Dynabook Toshiba PS461E-0S70D3EN User Manual

Download

User's Manual

R30-C/R30t-C/A30-C/A30t-C

R40-C/A40-C

Chapter 1

Chapter 2

Chapter 3

TOSHIBA Legal, Regulatory, and Safety

Regulatory Information ......................................................................... 1-2

Video Standard Notice .......................................................................... 1-8

ENERGY STAR® Program .................................................................... 1-9

Disposing of the computer and the computer's batteries ................. 1-9

Optical disc drive safety instructions ............................................... 1-10

General Precautions ........................................................................... 1-11

Safety Icons ......................................................................................... 1-13

Getting Started

Equipment checklist ............................................................................. 2-1

Conventions ........................................................................................... 2-1

Short model name ................................................................................. 2-2

Using your computer for the first time ................................................ 2-2

Turning off the power ............................................................................ 2-7

System Recovery ................................................................................ 2-11

The Grand Tour

The Grand Tour for R30-C/A30-C ......................................................... 3-1

The Grand Tour for R40-C/A40-C ....................................................... 3-11

Internal Hardware Components ......................................................... 3-22

Power Condition Descriptions ........................................................... 3-24

Chapter 4

User's Manual ii

Operating Basics

Using the Touch Screen (only for R30t-C/A30t-C) .............................. 4-1

Using the Touch Pad ............................................................................. 4-1

The Keyboard ......................................................................................... 4-2

Using the AccuPoint ............................................................................. 4-5

Using the Fingerprint Sensor ............................................................... 4-6

Optical disc drive ................................................................................ 4-13

TOSHIBA VIDEO PLAYER ................................................................... 4-21

TOSHIBA Blu-ray Disc Player ............................................................ 4-23

Battery .................................................................................................. 4-25

Wireless WAN Device (R30-C/A30-C) ................................................ 4-32

Wireless WAN Device (R40-C/A40-C) ................................................ 4-33

GPS Function ....................................................................................... 4-35

Additional memory module (only for R30-C/A30-C) ......................... 4-35

LAN ....................................................................................................... 4-40

Memory media ..................................................................................... 4-42

Smart Card ........................................................................................... 4-46

External Display .................................................................................. 4-47

TOSHIBA Hi-Speed Port Replicator III 180W/120W .......................... 4-51

Security lock ........................................................................................ 4-53

Optional TOSHIBA Accessories ........................................................ 4-53

Sound System and Video mode ......................................................... 4-54

Chapter 5

Chapter 6

Chapter 7

Utilities and Advanced Usage

Utilities and Applications ...................................................................... 5-1

Special features ..................................................................................... 5-4

Using the TOSHIBA Sleep Utility ......................................................... 5-6

TOSHIBA Password Utility ................................................................... 5-8

TOSHIBA HWSetup ............................................................................. 5-10

TOSHIBA PC Health Monitor .............................................................. 5-11

Using the Hard Disk Drive (HDD) Protection .................................... 5-12

TOSHIBA Setup Utility ........................................................................ 5-14

Troubleshooting

Problem-solving process ..................................................................... 6-1

Hardware and system checklist ........................................................... 6-4

TOSHIBA support ................................................................................ 6-16

Appendix

Specifications ........................................................................................ 7-1

AC Power Cord and Connectors .......................................................... 7-3

Information for Wireless Devices ........................................................ 7-4

Information about Intel AMT ............................................................... 7-15

Legal Footnotes ................................................................................... 7-17

VCCI Class B Information (Japan Only) ............................................ 7-20

OpenSSL Toolkit License Issues ....................................................... 7-21

FreeType License Issues .................................................................... 7-23

Index

User's Manual iii

Chapter 1

TOSHIBA Legal, Regulatory, and Safety

This chapter states the legal, regulatory, and safety information applicable to TOSHIBA computers.

Copyright, Disclaimer and Trademarks

Copyright

© 2015 TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

First edition October 2015 Copyright authority for music, movies, computer programs, databases and

other intellectual property covered by copyright laws belongs to the author or to the copyright owner. Copyrighted material can be reproduced only for personal use or use within the home. Any other use beyond that stipulated above (including conversion to digital format, alteration, transfer of copied material and distribution on a network) without the permission of the copyright owner is a violation of copyright or author's rights and is subject to civil damages or criminal action. Comply with copyright laws in making any reproduction from this manual.

Disclaimer

This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for your computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.

Trademarks

Intel is a trademark or registered trademark of Intel Corporation. Windows, Microsoft, and Windows logo are registered trademarks of

Microsoft Corporation.

User's Manual 1-

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Secure Digital and SD are trademarks of SD Card Association. MultiMediaCard and MMC are trademarks of MultiMediaCard Association. Blu-ray Disc™, Blu-ray™, and the logos are trademarks of the Blu-ray Disc

Association. Realtek is a registered trademark of Realtek Semiconductor Corporation. All other product names and service names in this manual might be

trademarks or registered trademarks of their respective companies.

Regulatory Information

The regulatory information herein might vary. Check the ID information on the bottom of the device or box for specific information applicable to the model you purchased.

FCC information

FCC notice "Declaration of Conformity Information"

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

User's Manual 1-

Only peripherals complying with the FCC class B limits can be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external RGB monitor port, Universal Serial Bus (USB

2.0 or 3.0) ports, HDMI out port and Headphone/Microphone jack. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment.

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Contact

Address: TOSHIBA America Information Systems, Inc.

9740 Irvine Boulevard Irvine, California 92618-1697

Telephone: (949) 583-3000

This information is only applicable for the countries/regions where it is required.

EU Declaration of Conformity

This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA EUROPE GMBH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site

http://epps.toshiba-teg.com on the Internet.

CE compliance

This product is labeled with the CE Mark in accordance with the related European Directives, notably RoHS Directive 2011/65/EU and Electromagnetic Compatibility Directive 2004/108/EC for the notebook and

User's Manual 1-

the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 1999/5/ EC in case of implemented telecommunication accessories and the Low Voltage Directive 2006/95/EC for the supplied power adapter. Furthermore the product complies with the Ecodesign Directive 2009/125/EC (ErP) and its related implementing measures.

This product and the original options are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected/implemented those options/cables have to provide assurance that the system (PC plus options/cables) still fulfils the required standards. To avoid general EMC problems, the following guidance should be noted:

Only CE marked options should be connected/implemented Only best shielded cables should be connected

Working environment

This product was designed to fulfil the EMC (Electromagnetic Compatibility) requirements to be observed for so-called “Residential, commercial and light industry environments”. TOSHIBA do not approve the use of this product in working environments other than the above mentioned “Residential, commercial and light industry environments”.

For example, the following environments are not approved:

Industrial Environments (e.g. environments where a mains voltage of 380 V three-phase is used)

Medical Environments Automotive Environments Aircraft Environments

Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA.

The consequences of the use of this product in non-approved working environments may be:

Interference with other devices or machines in the near surrounding area.

Malfunction of, or data loss from, this product caused by disturbances generated by other devices or machines in the near surrounding area.

Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non-approved working environments before use. In the case of automobiles or aircraft, the manufacturer or airline respectively should be asked for permission before use of this product.

Furthermore, for general safety reasons, the use of this product in environments with explosive atmospheres is not permitted.

User's Manual 1-

Canadian regulatory information (Canada only)

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications.

Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Following information is only valid for EU-member States:

Information requirements Regulation EC 1275/2008

Additional information as required by Regulation (EC)

1275/2008 amended by Regulation (EU) 801/2013 implementing European Eco-Design Directive with regard to requirements for standby, off mode and networked standby electric power consumption of electrical and electronic household and office equipment can be found here:

http://www.toshiba.eu/Eco-Design

Disposal of products

The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres.

The black bar indicates that the product was placed on the market after August 13, 2005.

By participating in the separate collection of products and batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health.

For more detailed information about the collection and recycling programmes available in your country, please visit our website

( www.toshiba.eu/recycling ) or contact your local council office or the retail outlet where you purchased the product.

User's Manual 1-5

Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste.

If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the European Battery Directive, then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.

By participating in the separate collection of batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health. To achieve this you should take any battery and/or accumulator to your local recycling site, or to a retail outlet or facility that offers to collect these devices for environmentally friendly disposal, ensuring that the terminal contacts are covered by non-conductive tape.

For more detailed information about the collection and recycling programmes available in your country, please visit our website

( www.toshiba.eu/recycling ) or contact your local council office or the retail outlet where you purchased the product.

These symbols might not stick depending on the country and region where you purchased.

REACH - Compliance Statement

The European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007, with phased deadlines to 2018.

Toshiba will meet all REACH requirements and is committed to provide our customers with information about the presence in our articles of substances included on the candidate list according to REACH regulation.

Please consult the following website www.toshiba.eu/reach for information about the presence in our articles of

substances included on the candidate list according to REACH in a concentration above 0.1 % weight by weight.

User's Manual 1-

Following information is only for Turkey:

Disposal of products:

The crossed wheelie bin symbol means that this product should not be collected and disposed with other household wastes. When product become waste at the end-of-life, to protect environment and human health, it should be given to nearest collection recycling or disposal center. For more information about collection and recycling programs in your country please contact your local authority or the retailer where the product was purchased.

Toshiba meets all requirements of Turkish regulation 28300 “Restriction of the use of certain hazardous substances in electrical and electronic equipment”.

AEEE Yönetmeliğine Uygundur

Toshiba 28300 sayılı Türkiye ''Elektrikle çalişan ve elektronik ekipmanda belirli tehlikeli maddelerin kullanimiyla ilgili kisitlama” yönetmeliği gereklerini tamamen yerine getirmektedir

The number of possible pixel failures of your display is defined according to ISO 9241-307 standards. If the number of pixel failures is less than this standard, they will not be counted as defect or failure.

Battery is a consumption product, since the battery time depends on the usage of your computer. If the battery can not be charged at all, then it is a defect or failure. The changes in battery time is not a defect or failure.

Following information is only for India:

The use of this symbol indicates that this product may not be treated as household waste.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

For more detailed information about recycling of this product, please visit our website

( http://www.toshiba-india.com ) or contact call center (1800-200-8674).

These symbols might not stick depending on the country and region where you purchased.

User's Manual 1-7

Video Standard Notice

THIS PRODUCT IS LICENSED UNDER THE AVC, THE VC-1 AND MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (I) ENCODING VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS ("VIDEO") AND/OR (II) DECODING AVC, VC-1 AND MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE

http://www.mpegla.com

User's Manual 1-8

ENERGY STAR® Program

Your Computer model may be ENERGY STAR compliant. If the model you purchased is compliant, it uses the ENERGY STAR logo and the following information applies.

TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency. Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes.

To conserve energy, your computer is set to enter the lowpower Sleep Mode which shuts down the system and display within 15 minutes of inactivity in AC power mode.

TOSHIBA recommends that you leave this and other energy saving features active, so that your computer will operate at its maximum energy efficiency. You can wake the computer from Sleep Mode by pressing the power button.

Your ENERGY STAR certified computer should be set by default to enter a low-power "sleep mode" after a period of inactivity. Simply touching the mouse or keyboard "wakes" the computer in seconds. These sleep features can save you up to $23 per year (200 kWh per year in electricity) and prevent up to 300 pounds of greenhouse gas emissions annually. To learn how to adjust or activate these sleep settings on your computer, please go to:

www.energystar.gov/sleepinstructions To activate sleep settings organization-wide quickly and

easily through network tools, please go to: www.energystar.gov/powermanagement

Disposing of the computer and the computer's batteries

Discard this computer in accordance with applicable laws and regulations. For further information, contact your local government.

This computer contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you need to replace them. Under certain applicable laws and regulation, it might be illegal to dispose of old batteries by placing them in the trash.

User's Manual 1-

Please be kind to our shared environment. Check with your local

TOSHIBA SAMSUNG STORAGE TECHNOLOGY KOREA CORPORATION 14F, Bldg. No.102, Digital empire2, 486 Sin-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea, 443-734

government authority for details regarding where to recycle old batteries or how to dispose of them properly.

Optical disc drive safety instructions

Be sure to check the precautions at the end of this section.

The drive model employs a laser system. To ensure proper use of this product, read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

Use of controls, adjustments or the performance of procedures other than those specified might result in hazardous radiation exposure.

To prevent direct exposure to the laser beam, do not try to open the enclosure.

Location of the Required Label

(Sample shown below. Location of the label and manufacturing information might vary.)

Precautions

CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.

User's Manual 1-10

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.

Be certain to read the following general precautions and to note the cautions included in the text of the manual.

Provide adequate ventilation

Always make sure that your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep Mode). In this condition, observe the following:

Never cover your computer or AC adaptor with any object. Never place your computer or AC adaptor near a heat source, such as

an electric blanket or heater. Never cover or block the air vents including those at the base of the

computer. Always operate your computer on a hard flat surface. Using your

computer on a carpet or other soft material can block the vents. Always provide sufficient space around the computer.

Overheating your computer or AC adaptor could cause system failure, computer or AC adaptor damage or a fire, possibly resulting in serious injury.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they might overheat.

To keep your computer in prime operating condition, protect your work area from:

Dust, moisture, and direct sunlight. Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the computer) or speakerphones.

Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters.

Extreme heat, cold, or humidity. Liquids and corrosive chemicals.

User's Manual 1-11

Stress injury

Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. It also includes information on work space design, posture, and lighting that can help reduce physical stress.

Heat injury

Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.

If the computer has been used for a long time, avoid direct contact with the metal plate supporting the various interface ports as this can become hot.

The surface of the AC adaptor can become hot when in use but this condition does not indicate a malfunction. If you need to transport the AC adaptor, disconnect it and let it cool before moving it.

Do not lay the AC adaptor on a material that is sensitive to heat as the material could become damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer's components or otherwise cause it to malfunction.

Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust and dirt, and use care with all liquids around it.

Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely. In these circumstances, you should get the computer inspected by an authorized service provider in order to assess the scope of any damage.

Clean the plastics of the computer using a cloth slightly dampened with water.

You can clean the display screen by spraying a small amount of glass cleaner onto a soft, clean cloth and then wiping the screen gently with the cloth.

Never spray cleaner directly onto the computer or let liquid run into any part of it. Never use harsh or caustic chemical products to clean the computer.

User's Manual 1-12

Moving the computer

While the computer is designed for flexible day-to-day usage, you should exercise a few simple precautions when moving it in order to help ensure trouble-free operation.

Make sure all disk/disc activity has ended before moving the computer.

Turn off (shut down) the computer. Disconnect the AC adaptor and all peripherals before moving the

computer. Close the display panel. Do not pick up the computer by its display panel. Before carrying your computer, shut it down, disconnect the AC

adaptor and allow it to cool down. A failure to follow this instruction might result in minor heat injury.

Do not expose the computer to rapid temperature changes (for example, in a situation where you carry the computer from a cold environment to a warm room). Do not turn on the power until condensation disappears.

Be careful not to subject the computer to impact or shock. A failure to follow this instruction could result in damage to computer, computer failure, or loss of data.

Never transport your computer with any cards installed. This might damage either the computer and/or the card resulting in computer failure.

Always use a suitable carry case when transporting the computer. When carrying your computer, be sure to hold it securely so that it

does not fall or hit anything. Do not carry your computer by holding any of its protruding elements.

Mobile phones

Be aware that the use of mobile phones can interfere with the audio system. The operation of the computer will not be impaired in any way, but it is recommended that a minimum distance of 30 cm is maintained between the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort. Be sure to read it before using the computer.

Safety Icons

Safety icons are used in this manual to bring important information to your attention. Each type of message is identified as follows.

User's Manual 1-13

Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.

A caution informs you that improper use of equipment or failure to follow instructions might cause data loss, equipment damage, or might result in minor or moderate injury.

Please read. A note is a hint or advice that helps you make best use of your equipment.

User's Manual 1-14

Getting Started

This chapter provides an equipment checklist, and basic information to start using your computer.

If you use an operating system that was not pre-installed by TOSHIBA, some of the features described in this manual might not function properly.

Equipment checklist

Carefully unpack your computer, taking care to save the box and packaging materials for future use.

Hardware

Check to make sure that you have all the following items:

TOSHIBA Portable Personal Computer Battery pack (preinstalled in the computer) AC adaptor and power cord (2-pin plug or 3-pin plug)

Documentation

Chapter 2

Quickstart Instruction Manual for Safety and Comfort Warranty Information

If any of the items are missing or damaged, contact your dealer immediately.

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Start

Click Tap the Touch Pad or click the left Touch

User's Manual 2-1

The word "Start" refers to the " " button in Windows 7.

Pad control button once. Left-click the mouse once. Tap the touch screen once (only for touch

screen models).

Right-click Click the right Touch Pad control button

Double-click Tap the Touch Pad or click the left Touch

Internal Storage Drive Your computer is equipped with one of the

Short model name

Model name of your computer is shortened and referred to as the following in this manual.

LCD Full Model Name Short Model

33.8cm (13.3")

PORTÉGÉ R30-C/R30t-C/A30-C/A30t-C; Satellite R30-C/R30t-C/A30-C/A30t-C; Satellite Pro R30-C/R30t-C/A30-C/A30t-C

once. Right-click the mouse once. Press and hold on the touch screen (only for

touch screen models).

Pad control button twice. Left-click the mouse twice. Tap the touch screen twice (only for touch

screen models).

following storage devices:

HDD (Hard Disk Drive) SSD (Solid-State Drive)

In this manual, the word "internal storage drive" refers to either HDD or SSD unless otherwise stated.

Name

R30-C/A30-C

35.6cm (14.0")

TECRA A40-C; Satellite Pro A40-C; Satellite Pro R40-C

R40-C/A40-C

Using your computer for the first time

Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it, you can reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders, or neck.

This section provides basic information to start using your computer. It covers the following topics:

Connecting the AC adaptor Opening the display

User's Manual 2-

Turning on the power Initial setup Getting to know Windows

Use a virus-check program and make sure that it is updated regularly.

Never format storage media without checking its content - formatting destroys all stored data.

It is a good idea to back up the internal storage drive or other main storage device to external media periodically. General storage media is not durable or stable over long periods of time and under certain conditions might result in data loss.

Before you install a device or application, save any data in memory to the internal storage drive or other storage media. Failure to do so might result in data loss.

Connecting the AC adaptor

Attach the AC adaptor when you want to charge the battery or operate from AC power. The battery pack must be charged before you can operate from battery power.

The AC adaptor can automatically adjust to any voltage ranging from 100 volts to 240 volts and to a frequency of either 50 hertz or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer.

Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor might cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.

Never plug the AC adaptor into a power source that does not correspond to both the voltage range and the frequency specified on the regulatory label of the unit. Failure to do so might result in a fire or electric shock, possibly resulting in serious injury.

Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use. Failure to do so might result in a fire or electric shock, possibly resulting in serious injury.

The supplied power cord conforms to safety rules and regulations in the region the computer is bought and should not be used outside this region. For use in other regions, buy power cords that conform to safety rules and regulations in the particular region.

Do not use a 3-pin to 2-pin conversion plug.

User's Manual 2-3

When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in this User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug might hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.

Never place your computer or AC adaptor on a wooden surface, furniture, or any other surface that might be marred by exposure to heat since the computer base and the surface of the AC adaptor increase in temperature during normal use.

Always place your computer or AC adaptor on a flat and hard surface that is resistant to heat damage.

Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions.

1. Connect the power cord to the AC adaptor.

Figure 2-1 Connecting the power cord to the AC adaptor (2-pin plug)

Figure 2-2 Connecting the power cord to the AC adaptor (3-pin plug)

Either a 2-pin or 3-pin adaptor/cord is included with the computer depending on the model.

User's Manual 2-4

2. Connect the DC output plug of the AC adaptor to the DC IN 19V jack

on your computer.

Figure 2-3 Connecting the DC output plug to the computer (R30-C/A30-C)

Figure 2-4 Connecting the DC output plug to the computer (R40-C/A40-C)

1. DC IN 19V jack 2. DC output plug

Product appearance depends on the model you purchased.

3. Plug the power cord into a live wall outlet. The DC IN/Battery indicator glows.

Opening the display

The display panel can be opened to a wide range of angles for optimal viewing.

While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel. This will allow the angle of the display panel to be adjusted to provide optimum clarity.

Figure 2-5 Opening the display panel (R30-C/A30-C)

1. Display panel

Product appearance depends on the model you purchased.

User's Manual 2-

Open and close the display panel with reasonable care. Opening it vigorously or slamming it shut might damage the computer.

Do not put your fingers in the gap between the LCD panel and battery pack when closing your LCD, otherwise your fingers might get hurt.

Be careful not to open the display panel too far as this might put stress on the display panel’s hinges and cause damage.

Do not press or push on the display panel.

Do not lift the computer by the display panel.

Do not close the display panel with pens or any other objects left in between the display panel and the keyboard.

When opening or closing the display panel, place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the display panel (Do not use excessive force when opening or closing the display panel).

Turning on the power

This section describes how to turn on the power. The Power indicator indicates the status. Refer to the Power Condition Descriptions section for more information.

After you turn on the power for the first time, do not turn it off until you have set up the operating system.

Volume cannot be adjusted during Windows Setup.

Do not touch the display screen while turning on the computer.

1. Open the display panel. Press the power button.

User's Manual 2-

Figure 2-6 Turning on the power (R30-C/A30-C)

1. Power button

Product appearance depends on the model you purchased.

Initial setup

The Windows Startup Screen is the first screen displayed when you turn on the power. To install the operating system properly, follow the on-screen instructions on each screen.

When it is displayed, be sure to read the license terms and license agreement carefully.

Turning off the power

The power can be turned off in one of the following modes, either Shut Down Mode, Sleep Mode or Hibernation Mode.

Shut Down Mode

When you turn off the power in Shut Down Mode, no data will be saved and the computer will boot to the main screen of the operating system the next time it is turned on.

If you have entered data, either save it to the internal storage drive or

1. to other storage media.

2. Make sure all disk/disc activity has stopped before removing the disk/ disc.

If you turn off the power while a disk (disc) is being accessed, you might lose data or damage the disk.

Never turn off the power while an application is running. Failure to do so can cause data loss.

Never turn off the power, disconnect an external storage device, or remove storage media during data read/write. Failure to do so can cause data loss.

User's Manual 2-7

3. Click Start and then select Shut down. Turn off any peripheral devices connected to your computer.

Do not turn the computer or peripheral devices back on immediately. Wait a short period to avoid any potential damage.

Restarting the computer

Certain conditions require that you reset the computer, for example if:

You change certain computer settings.

To restart the computer, there are several ways this can be achieved:

Click Start. Point to the arrow ( ) beside the Shut down then select Restart.

Press CTRL, ALT, and DEL menu window, and then select Restart by clicking the power icon ( in the lower-right corner.

Before restarting the computer, be sure to save your data.

simultaneously (once) to display the

Sleep Mode

If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode, data is maintained in the main memory of the computer. When you turn on the power again, you can continue working right where you left off.

When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always shut down the computer. This includes turning off any wireless communication functionalities, and canceling settings that reactivate the computer automatically, such as a timer recording function. Failure to shut down the computer in this way might allow the operating system to reactivate and run pre-programmed tasks or preserve unsaved data, which might interfere with aviation or other systems, possibly causing serious injury.

button and

)

Before entering Sleep Mode, be sure to save your data.

To prevent data loss, do not switch to Sleep Mode while transferring data to external media, such as USB devices, memory media, or other external memory devices.

Do not remove the battery pack while the computer is in Sleep Mode (unless the computer is connected to an AC power source). It can cause data loss in the memory.

User's Manual 2-8

When the AC adaptor is connected, the computer will go into Sleep Mode according to the settings in the Power Options (to access it, click Start

-> Control Panel -> System and Security -> Power

Options).

To restore the operation of the computer from Sleep Mode, press and hold the power button or any key on the keyboard for a short amount of time. Note that keyboard keys can only be used if the Wake-up on Keyboard option is enabled within the TOSHIBA HWSetup.

If the computer enters Sleep Mode while a network application is active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.

To prevent the computer from automatically entering Sleep Mode, disable Sleep Mode within the Power Options.

To use the Hybrid Sleep function, configure it in the Power Options.

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

Restores the previous working environment more rapidly than the Hibernation Mode feature.

Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Sleep Mode feature.

Allows the use of the panel power off feature.

Executing Sleep Mode

You can enter Sleep Mode in one of following ways:

Click Start. Point to the arrow ( ) beside the Shut down

button and

then select Sleep. Close the display panel. Note that this feature must be enabled within

the Power Options. Press the power button. Note that this feature must be enabled within

the Power Options.

When you turn the power back on, you can continue where you left off when you shut down the computer.

When the computer is in Sleep Mode, the Power indicator blinks amber.

If you are operating the computer on battery power, you can lengthen the overall operating time by turning it off into Hibernation Mode. Sleep Mode consumes more power while the computer is off.

User's Manual 2-9

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

Power is turned back on immediately after shutting down. Memory circuits are exposed to static electricity or electrical noise. The battery power is exhausted and the AC Adaptor is not connected.

Hibernation Mode

The Hibernation Mode feature saves the contents of memory to the internal storage drive when the computer is turned off so that, the next time it is turned on, the previous state is restored. Note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer.

Save your data. While entering Hibernation Mode, the computer saves the contents of memory to the internal storage drive. However, for safety sake, it is best to save your data manually.

Data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed.

To prevent data loss, do not switch to Hibernation Mode while transferring data to external media, such as USB devices, memory media, or other external memory devices.

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

Saves data to the internal storage drive when the computer automatically shuts down because of a low battery condition.

You can return to your previous working environment immediately when you turn on the computer.

Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature.

Allows the use of the panel power off feature.

Starting Hibernation Mode

To enter Hibernation Mode, click Start, point to the arrow ( Shut down button and then select Hibernate

from the menu.

) beside the

Automatic Hibernation Mode

The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the display panel.To define these settings, do the following:

1. Click Start -> Control Panel -> System and Security -> Power Options.

User's Manual 2-10

2. Click Choose what the power button does closing the lid does.

3. Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid.

4. Click the Save changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer takes a moment to save the current data in memory to the internal storage drive.

After you turn off the computer, and the content of memory has been saved to the internal storage drive, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

System Recovery

There is a hidden partition allocated on the internal storage drive for the System Recovery Options in the event of a problem.

You can also create recovery media and restore the system. The following items are described in this section:

System Recovery Options Creating Recovery Media Restoring the pre-installed software from your created Recovery

Media Restoring the pre-installed software from the Recovery Partition

or Choose what

System Recovery Options

The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes tools to repair startup problems, run diagnostics, or restore the system.

See the Windows Help and Support content for more information about Startup Repair.

The System Recovery Options can also be run manually to repair problems.

The procedure is as follows. Follow the instructions shown on the onscreen menu.

Turn off the computer.

2. While holding the F8 key, turn on the computer.

3. The Advanced Boot Options menu is displayed. Use the arrow keys to select Repair Your Computer and press ENTER.

4. Follow the on-screen instructions.

User's Manual 2-11

Check your Windows® system (including the system image backup feature).

manual for more information on backing up your

Creating Recovery Media

This section describes how to create Recovery Media.

Be sure to connect the AC adaptor when you create Recovery Media.

Be sure to close all other software programs except the Recovery Media Creator.

Do not run software such as screen savers which can put a heavy load on the CPU.

Operate the computer at full power.

Do not use power-saving features.

Do not write to the media when the virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.

Do not use utilities, including those intended to enhance internal storage drive access speed. They might cause unstable operation and damage data.

Do not shut down/log off or Sleep/Hibernate while writing or rewriting the media.

Set the computer on a level surface and avoid places subjected to vibrations such as airplanes, trains, or cars.

Do not use on an unstable surface such as a stand.

A recovery image of the software on your computer is stored on the internal storage drive, and can be copied to either disc media or USB Flash Memory by using the following steps:

Select either blank disc or USB Flash Memory.

1. The application allows you to choose from a variety of different media onto which the recovery image can be copied including disc media and USB Flash Memory.

Some of the disc media might not be compatible with the optical disc drive connected to your computer. You should therefore verify that the optical disc drive supports the blank media you have chosen before proceeding.

USB Flash Memory will be formatted and all the data in the USB Flash Memory will be lost when proceeding.

2. Turn on your computer and allow it to load the Windows operating system from the internal storage drive as normal.

User's Manual 2-12

3. Insert the first blank disc into the optical disc drive tray, or insert the USB Flash Memory into one available USB port.

Click Start -> All Programs -> TOSHIBA -> Support & Recovery ->

4. Recovery Media Creator.

5. After Recovery Media Creator starts, select the type of media and the title you wish to copy, and then click the Create button.

Restoring the pre-installed software from your created Recovery Media

If the pre-installed files are damaged, you are able to use the Recovery Media you have created to restore the computer to the state it was in when you originally received it. To perform this restoration, do the following:

Make sure that the AC adaptor is connected during the restoring process.

Do not close the display panel during the restoring process.

When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

1. Load the Recovery Media into the Optical Disc Drive or insert the recovery USB Flash Memory into one available USB port.

Click Start. Point to the arrow (

2. then select Restart.

Hold down the F12 key and then release this key one second after the

3. computer is power on.

4. Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media.

5. A menu is displayed from which you should follow the on-screen instructions.

If you have previously chosen to remove the recovery partition and are trying to create "Recovery Media", the following message appears: "The Recovery Media Creator can not be launched because there is no recovery partition."

When there is no recovery partition, the Recovery Media Creator cannot make Recovery Media.

However, if you have already created a "Recovery Media", you can use it to restore the recovery partition.

If you have not created "Recovery Media", contact TOSHIBA support for assistance.

) beside the Shut down button and,

User's Manual 2-13

Restoring the pre-installed software from the Recovery Partition

A portion of the total internal storage drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem.

If you set up your internal storage drive again later, do not change, delete, or add partitions in a manner other than specified in the manual, otherwise you might find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the partitions on your internal storage drive, you might find that it becomes impossible to set up your computer.

Make sure that the AC adaptor is connected during the restoring process.

Do not close the display panel during the restoring process.

When you reinstall the Windows operating system, the internal storage drive will be reformatted and all data will be lost.

1. Click Start. Point to the arrow ( ) beside the Shut down button and, then select Restart.

Hold down 0 (zero) key and then release this key one second after the

2. computer is power on.

3. Follow the on screen instructions to finish the recovery.

User's Manual 2-14

Chapter 3

2 4

65 11

The Grand Tour

This chapter identifies the various components of the computer. It is recommended that you become familiar with each before you operate the computer.

Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, refer to the Legal

Footnotes section.

Handle your computer carefully to avoid scratching or damaging the surface.

The Grand Tour for R30-C/A30-C

Front with the display closed (R30-C/A30-C)

The following figure shows the front of the computer with the display panel in the closed position.

Figure 3-1 Front of the computer with display panel closed (R30-C/A30-C)

1. Stereo speakers 5. Memory media slot

2. DC IN/Battery indicator 6. Wireless communication indicator*

3. Power indicator 7. Wireless WAN indicator*

4. Internal storage drive indicator

* Provided with some models. Product appearance depends on the model you purchased.

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low battery condition, generated by the system.

User's Manual 3-1

DC IN/Battery indicator

Power indicator The Power indicator normally glows white when

The DC IN/Battery indicator shows the condition of the DC IN and the battery charge status. White indicates that the battery is fully charged while the power is being correctly supplied from the AC power adaptor.

Refer to the Power Condition Descriptions section for more information on this feature.

the computer is turned on. However, if you turn off the computer into Sleep Mode, this indicator flashes amber.

Internal storage drive indicator

Memory media slot This slot lets you insert an SD™/SDHC™/

Keep foreign metal objects, such as screws, staples, and paper clips, out of the Memory media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Wireless communication indicator

Wireless WAN indicator

The Internal storage drive indicator blinks white whenever the computer is accessing the internal storage drive.

SDXC™ memory card, miniSD™/microSD™ Card and MultiMediaCard™. Refer to the

Memory media section for more information.

The Wireless communication indicator glows white when the wireless functions are turned on.

Some models are equipped with wireless functions.

The Wireless WAN indicator glows blue when the Wireless WAN function is turned on.

For some models, the indicator blinks to indicate the connection status of the Wireless WAN function.

Some models are equipped with the Wireless WAN function.

Left side (R30-C/A30-C)

The following figure shows the left side of the computer.

User's Manual 3-

Figure 3-2 The left side of the computer (R30-C/A30-C)

1 2 3

1. DC IN 19V jack 4. Optical disc drive*

2. LAN jack 5. Smart Card slot*

3. Universal Serial Bus (USB 3.0) port

* Provided with some models. Product appearance depends on the model you purchased.

DC IN 19V jack The AC adaptor connects to this jack in order to

power the computer and charge its internal batteries. Note that you must only use the model of AC adaptor supplied with the computer at the time of purchase. Using the wrong AC adaptor can damage the computer.

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to Operating

Basics, for details.

Do not connect any cable other than a LAN cable to the LAN jack. It might cause damage or malfunction.

Universal Serial Bus (USB 3.0) port

One Universal Serial Bus port, which complies to the USB 3.0 standard, is provided on the left side of the computer.

The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices.

The port with the icon ( ) has Sleep and Charge function, and this function is only provided with some models.

USB 3.0 port(s) might work as USB 2.0 port(s) when operating in USB Legacy Emulation mode.

User's Manual 3-3

Note that it is not possible to confirm the operation of all functions of

1 2 4 6532

all USB devices that are available. Some functions associated with a specific device might not operate properly.

Before removing a USB device from the USB port of your computer, click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar, and then select the USB device that you want to remove.

Keep foreign metal objects, such as screws, staples, and paper clips, out of the USB port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Optical disc drive The computer might be configured with a DVD

Super Multi drive or Blu-ray drive. Some models are equipped with an Optical disc

drive.

2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.

Smart Card slot This slot allows you to install a Smart Card

device. Some models are equipped with a Smart Card

slot.

Right side (R30-C/A30-C)

The following figure shows the right side of the computer.

Figure 3-3 The right side of the computer (R30-C/A30-C)

1. Headphone/Microphone jack 4. External RGB monitor port

2. Universal Serial Bus (USB 3.0) port 5. Cooling vents

3. HDMI out port 6. Security lock slot

Product appearance depends on the model you purchased.

Headphone/ Microphone jack

User's Manual 3-4

A 3.5 mm mini headphone/microphone jack enables connection of a monaural microphone or stereo headphones.

Universal Serial Bus (USB 3.0) ports

Two Universal Serial Bus ports, which comply to the USB 3.0 standard, are provided on the right side of the computer.

USB 3.0 ports are compliant with USB 3.0 standard and backward compatible with USB 2.0 devices.

USB 3.0 port(s) might work as USB 2.0 port(s) when operating in USB Legacy Emulation mode.

Note that it is not possible to confirm the operation of all functions of all USB devices that are available. Some functions associated with a specific device might not operate properly.

Before removing a USB device from the USB port of your computer, click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar, and then select the USB device that you want to remove.

HDMI out port HDMI out port can connect with Type A

connector HDMI cable.

External RGB monitor port

This port provides 15-pin, analog RGB port. Refer to the External RGB monitor port pin

assignment section for information on external

RGB monitor port pin assignment. This port allows you to connect an external RGB monitor to the computer.

Cooling vents The cooling vents help the processor to avoid

overheating.

Do not block the cooling vents. Keep foreign metal objects, such as screws, staples, and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Carefully clean the dust on the surface of the cooling vents using a soft cloth.

Security lock slot A security cable can be attached to this slot and

then connected to a desk or other large object in order to deter theft of the computer.

User's Manual 3-5

Back (R30-C/A30-C)

The following figure shows the back of the computer.

Figure 3-4 The back of the computer (R30-C/A30-C)

1. Battery pack

Product appearance depends on the model you purchased.

Battery pack The rechargeable lithium-ion battery pack

provides power to the computer when the AC adaptor is not connected.

For more detailed information on the use and operation of the battery pack, refer to the Battery section.

Legal Footnote (Battery Life) For more information regarding Battery Life, refer to the Legal Footnotes

section.

Underside (R30-C/A30-C)

The following figures show the underside of the computer. Ensure that the display is closed before the computer is turned over to avoid causing any damage.

Figure 3-5 The underside of the computer (R30-C/A30-C)

1. Battery lock 4. Docking port*

2. Battery release latch 5. Memory module cover*

3. Cooling vents

* Provided with some models. Product appearance depends on the model you purchased.

User's Manual 3-

Battery lock Slide the battery lock to release the battery pack

ready for removal.

Battery release latch Slide and hold this latch into its "Unlock" position

in order to release the battery pack for removal. For more detailed information on removing the battery pack, refer to the Battery

section.

Cooling vents The cooling vents help the processor to avoid

overheating.

Carefully clean the dust on the surface of the cooling vents using a soft cloth.

Docking port This port enables connection of an optional

TOSHIBA Hi-Speed Port Replicator III 180W/ 120W described in TOSHIBA Hi-Speed Port

Replicator III 180W/120W.

Some models are equipped with the docking port.

Only the TOSHIBA Hi-Speed Port Replicator III 180W or 120W is compatible with the docking port.

Do not attempt to use any other Port Replicator.

Keep foreign objects out of the docking port. A pin or similar object can damage the circuitry of the computer.

Memory module cover

Some models are equipped with the memory module cover. The memory module slot under this cover allows for the installation, replacement and removal of additional memory module.

4GB or 8GB memory modules can be installed in the computer's two memory slots for a maximum of 16GB system memory. The actual amount of useable system memory is less than the installed memory modules.

Refer to the Additional memory module section.

User's Manual 3-

Front with the display open (R30-C/A30-C)

8 8

2 3

8 8

2 3

This section shows the computer with the display panel open. In order to open the display, lift up the display panel and position it at a comfortable viewing angle for you.

Figure 3-6 The front of the computer with the display panel open (R30-C/A30-C)

1. Wireless communication antennas (not shown)*

2. Microphone* 10. AccuPoint*

3. Microphone* 11. AccuPoint control buttons*

4. Web Camera* 12. Touch Pad ON/OFF icon

5. Web Camera LED* 13. TOSHIBA eco icon

6. Display screen 14. Touch Pad

7. Power button 15. Touch Pad control buttons

8. Display hinges 16. Fingerprint Sensor*

User's Manual 3-

* Provided with some models. Product appearance depends on the model you purchased.

9. Keyboard

Wireless communication antennas

Depending on the configuration of your computer, one or all of the following antennas are built-in:

Wireless LAN Wireless LAN/Bluetooth

Some models are equipped with wireless communication antennas.

Do not cover the wireless communication antennas area with any metal objects, otherwise the wireless function might not work.

Legal Footnote (Wireless LAN) For more information regarding Wireless LAN, refer to the Legal Footnotes

section.

Microphone The built-in microphone allows you to record

sounds for your application. Refer to the Sound

System and Video mode section for more

information. Some models are equipped with the built-in

microphone.

Web Camera Web Camera

is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool.

Some models are equipped with a Web Camera.

Do not point the web camera directly at the sun.

Do not touch or press strongly on the web camera lens. Failure to do so might reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.

Web Camera LED The Web Camera LED glows when the Web

Camera is operating. Some models are equipped with a Web Camera

LED.

User's Manual 3-9

Display screen 33.8 cm (13.3") LCD screen, configured with one

of the following resolutions depending on the model you purchased:

HD, 1366 horizontal x 768 vertical pixels FHD, 1920 horizontal x 1080 vertical pixels

Be aware that, when the computer is operating on the AC adaptor, the image displayed on the internal screen is somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when operating on batteries.

Legal Footnote (LCD) For more information regarding LCD, refer to the Legal Footnotes section.

Power button Press this button to power on/off the computer.

Display hinges The display hinges allow the display panel to be

positioned at a variety of easy-to-view angles.

Keyboard The keyboard contains character keys, control

keys, function keys, and special Windows keys, providing all the functionality of a full-size keyboard.

Refer to the The Keyboard

section for details.

AccuPoint A pointer control device located in the center of

the keyboard is used to control the on-screen pointer. Some models are equipped with an AccuPoint.

AccuPoint control buttons

Control buttons below the keyboard let you select menu items or manipulate text and graphics designated by the on-screen pointer. Only models equipped with an AccuPoint are equipped with AccuPoint control buttons.

Touch Pad ON/OFF icon

Double tap this icon to enable/disable the Touch Pad.

TOSHIBA eco icon Double tap this icon to launch the TOSHIBA eco

Utility.

User's Manual 3-10

Touch Pad The Touch Pad located in the palm rest is used

21 14

to control the movement of the mouse pointer. To use the Touch Pad, simply touch and move

your fingertip across it in the direction you want the mouse pointer to go.

Touch Pad control buttons

The two buttons below the Touch Pad are used like the buttons on a standard mouse. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using.

Fingerprint Sensor This sensor enables you to enroll and recognize

a fingerprint. Some models are equipped with a Fingerprint

Sensor.

The Grand Tour for R40-C/A40-C

Front with the display closed (R40-C/A40-C)

The following figure shows the front of the computer with the display panel in the closed position.

Figure 3-7 Front of the computer with display panel closed

1. Stereo speakers 3. Power indicator

2. DC IN/Battery indicator 4. Wireless communication indicator*

* Provided with some models. Product appearance depends on the model you purchased.

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low battery condition, generated by the system.

DC IN/Battery indicator

Refer to the Power Condition Descriptions section for more information on this feature.

User's Manual 3-11

Power indicator The Power indicator normally glows white when

1 2

43 5

the computer is turned on. However, if you turn off the computer into Sleep Mode, this indicator flashes amber.

Wireless communication indicator

The Wireless communication indicator glows white when the wireless functions are turned on.

Some models are equipped with wireless functions.

Left side (R40-C/A40-C)

The following figures show the left side of the computer.

Figure 3-8 The left side of the computer

1. Security lock slot 5. Memory media slot

2. Optical disc drive* 6. Smart Card slot*

3. Universal Serial Bus (USB 3.0) port 7. SIM card slot*

4. Headphone/Microphone jack 8. Wireless WAN indicator*

* Provided with some models. Product appearance depends on the model you purchased.

User's Manual 3-12

Security lock slot A security cable can be attached to this slot and

then connected to a desk or other large object in order to deter theft of the computer.

Optical disc drive The computer might be configured with a DVD

Super Multi drive. Some models are equipped with an Optical disc

drive.

2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.

Universal Serial Bus (USB 3.0) port

One Universal Serial Bus port, which complies to the USB 3.0 standard, is provided on the left side of the computer.

The USB 3.0 ports are compliant with USB 3.0 standard and backward compatible with USB 2.0 devices.

USB 3.0 port(s) might work as USB 2.0 port(s) when operating in USB Legacy Emulation mode.

Note that it is not possible to confirm the operation of all functions of all USB devices that are available. Some functions associated with a specific device might not operate properly.

Before removing a USB device from the USB port of your computer, click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar, and then select the USB device that you want to remove.

Headphone/ Microphone jack

A 3.5 mm mini headphone/microphone jack enables connection of a monaural microphone or stereo headphones.

Memory media slot This slot lets you insert an SD™/SDHC™/

SDXC™ memory card, miniSD™/microSD™ Card and MultiMediaCard™. Refer to the

Memory media section for more information.

Smart Card slot This slot allows you to install a Smart Card

device. Some models are equipped with a Smart Card

slot.

User's Manual 3-13

SIM Card slot This slot allows you insert a SIM card which

1 2 3 4

65 7

enables a high-speed access to the Internet, corporate Intranet and your email while you are away from office.

Refer to the Wireless WAN Device (R40-C/A40-

C) section for more information.

Some models are equipped with the SIM Card slot.

Wireless WAN indicator

The Wireless WAN indicator glows blue when the Wireless WAN function is turned on.

For some models, the indicator blinks to indicate the connection status of the Wireless WAN function.

Some models are equipped with the Wireless WAN function.

Right side (R40-C/A40-C)

The following figure shows the right side of the computer.

Figure 3-9 The right side of the computer

1. Universal Serial Bus (USB 3.0) port 5. Cooling vents

2. Universal Serial Bus (USB 3.0) port 6. LAN jack

3. HDMI out port* 7. DC IN 19V jack

4. External RGB monitor port

* Provided with some models. Product appearance depends on the model you purchased.

Universal Serial Bus (USB 3.0) ports

Two Universal Serial Bus ports, which comply to the USB 3.0 standard, are provided on the right side of the computer.

USB 3.0 ports are compliant with USB 3.0 standard and backward compatible with USB 2.0 devices.

The port with the icon ( ) has Sleep and Charge function, and this function is only provided with some models.

User's Manual 3-14

USB 3.0 port(s) might work as USB 2.0 port(s) when operating in USB Legacy Emulation mode.

Note that it is not possible to confirm the operation of all functions of all USB devices that are available. Some functions associated with a specific device might not operate properly.

Before removing a USB device from the USB port of your computer, click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar, and then select the USB device that you want to remove.

HDMI out port HDMI out port can connect with Type A

connector HDMI cable.

External RGB monitor port

This port provides 15-pin, analog RGB port. Refer to the External RGB monitor port pin

assignment section for information on external

RGB monitor port pin assignment. This port allows you to connect an external RGB monitor to the computer.

Cooling vents The cooling vents help the processor to avoid

overheating.

Carefully clean the dust on the surface of the cooling vents using a soft cloth.

LAN jack This jack lets you connect to a LAN. The adaptor

Basics, for details.

User's Manual 3-15

Do not connect any cable other than a LAN cable to the LAN jack. It might

cause damage or malfunction.

DC IN 19V jack The AC adaptor connects to this jack in order to

Back (R40-C/A40-C)

The following figure shows the back of the computer.

Figure 3-10 The back of the computer

1. Battery pack

Product appearance depends on the model you purchased.

Battery pack The rechargeable lithium-ion battery pack

provides power to the computer when the AC adaptor is not connected.

For more detailed information on the use and operation of the battery pack, refer to the Battery section.

Legal Footnote (Battery Life) For more information regarding Battery Life, refer to the Legal Footnotes

section.

Underside (R40-C/A40-C)

The following figure shows the underside of the computer. Ensure that the display is closed before the computer is turned over to avoid causing any damage.

User's Manual 3-16

Figure 3-11 The underside of the computer

1. Battery lock 3. Cooling vents

2. Battery release latch 4. Docking port*

* Provided with some models. Product appearance depends on the model you purchased.

Battery lock Slide the battery lock to release the battery pack

ready for removal.

Battery release latch Slide and hold this latch into its "Unlock" position

in order to release the battery pack for removal. For more detailed information on removing the battery pack, refer to the Battery

section.

Cooling vents The cooling vents help the processor to avoid

overheating.

Carefully clean the dust on the surface of the cooling vents using a soft cloth.

Docking port This port enables connection of an optional

TOSHIBA Hi-Speed Port Replicator III 180W/ 120W described in TOSHIBA Hi-Speed Port

Replicator III 180W/120W.

Some models are equipped with the docking port.

Only the TOSHIBA Hi-Speed Port Replicator III 180W or 120W is compatible with the docking port.

Do not attempt to use any other Port Replicator.

Keep foreign objects out of the docking port. A pin or similar object can damage the circuitry of the computer.

User's Manual 3-17

Front with the display open (R40-C/A40-C)

This section shows the computer with the display panel open. In order to open the display, lift up the display panel and position it at a comfortable viewing angle for you.

User's Manual 3-18

Figure 3-12 The front of the computer with the display panel open

8 8

2 3

8 8

2 3

1. Wireless communication antennas (not shown)*

2. Microphone* 10. AccuPoint*

3. Microphone* 11. AccuPoint control buttons*

4. Web Camera* 12. Touch Pad ON/OFF icon*

5. Web Camera LED* 13. TOSHIBA eco icon*

6. Display screen 14. Touch Pad

7. Power button 15. Touch Pad control buttons

8. Display hinges 16. Fingerprint Sensor*

User's Manual 3-19

* Provided with some models. Product appearance depends on the model you purchased.

9. Keyboard

Wireless communication antennas

Depending on the configuration of your computer, one or all of the following antennas are built-in:

Wireless LAN Wireless LAN/Bluetooth

Some models are equipped with wireless communication antennas.

Do not cover the wireless communication antennas area with any metal objects, otherwise the wireless function might not work.

Legal Footnote (Wireless LAN) For more information regarding Wireless LAN, refer to the Legal Footnotes

section.

Microphone The built-in microphone allows you to record

sounds for your application. Refer to the Sound

System and Video mode section for more

information. Some models are equipped with the built-in

microphone.

Web Camera Web Camera

is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool.

Some models are equipped with a Web Camera.

Do not point the web camera directly at the sun.

Do not touch or press strongly on the web camera lens. Failure to do so might reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.

Web Camera LED The Web Camera LED glows when the Web

Camera is operating. Some models are equipped with a Web Camera

LED.

User's Manual 3-20

Display screen 35.6 cm (14.0") LCD screen, configured with one

of the following resolutions depending on the model you purchased:

HD, 1366 horizontal x 768 vertical pixels FHD, 1920 horizontal x 1080 vertical pixels

Legal Footnote (LCD) For more information regarding LCD, refer to the Legal Footnotes section.

Power button Press this button to power on/off the computer.

Display hinges The display hinges allow the display panel to be

positioned at a variety of easy-to-view angles.

Keyboard The keyboard contains character keys, control

keys, function keys, and special Windows keys, providing all the functionality of a full-size keyboard.

Refer to the The Keyboard

section for details.

AccuPoint A pointer control device located in the center of

the keyboard is used to control the on-screen pointer. Some models are equipped with an AccuPoint.

AccuPoint control buttons

Touch Pad ON/OFF icon

Double tap this icon to enable/disable the Touch Pad.

Some models are equipped with the Touch Pad ON/OFF icon.

User's Manual 3-21

TOSHIBA eco icon Double tap this icon to launch the TOSHIBA eco

Utility. Some models are equipped with the TOSHIBA

eco icon.

Touch Pad The Touch Pad located in the palm rest is used

to control the movement of the mouse pointer. To use the Touch Pad, simply touch and move

your fingertip across it in the direction you want the mouse pointer to go.

Touch Pad control buttons

Fingerprint Sensor This sensor enables you to enroll and recognize

a fingerprint. Some models are equipped with a Fingerprint

Sensor.

Internal Hardware Components

This section describes the internal hardware components of your computer. The actual specifications might vary depending on the model you

purchased.

CPU The processor type varies depending on model.

To check which type of processor is included in your model, open the TOSHIBA PC Diagnostic Tool by clicking Start

TOSHIBA -> Support & Recovery -> PC Diagnostic Tool.

-> All Programs ->

Legal Footnote (CPU) For more information regarding CPU, refer to the Legal Footnotes section.

User's Manual 3-22

Internal Storage Drive The capacity of the internal storage drive varies

depending on the model. To check which type of internal storage drive is

included in your model, open the TOSHIBA PC Diagnostic Tool by clicking Start -> All

Programs -> TOSHIBA -> Support & Recovery

-> PC Diagnostic Tool.

Note that part of the internal storage drive overall capacity is reserved as administration space.

Some models are equipped with a "Solid-State Drive (SSD)" instead of a hard disk drive. In this manual, the word "HDD" or "Hard disk drive" also refers to the SSD unless otherwise stated.

SSD is a large-capacity storage device which uses Solid-State Memory in place of a magnetic disk of the hard disk.

Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the HDD/SSD might be vulnerable to data retention errors.

Legal Footnote (Internal Storage Drive Capacity) For more information regarding Internal Storage Drive Capacity, refer to the

Legal Footnotes section.

RTC battery The internal RTC battery backs up the Real-Time

Clock (RTC) and calendar.

Video RAM The memory in the graphics adaptor of the

computer, used to store the image displayed on a bitmap display.

The amount of Video RAM available depends on the system memory of the computer.

Click Start

-> Control Panel -> Appearance

and Personalization -> Display -> Adjust resolution.

The amount of Video RAM can be verified by clicking the Advanced settings button in the Screen Resolution window.

User's Manual 3-23

Graphics Processing Unit

Legal Footnote (Graphics Processing Unit (GPU)) For more information regarding Graphics Processing Unit (GPU), refer to

the Legal Footnotes section.

Graphics Processing Unit (GPU) performance might vary depending on product model, design configuration, applications, power management settings and features utilized. GPU performance is only optimized when operating in AC power mode and might decrease considerably when operating in battery power mode.

Intel® Display Power Saving Technology

Intel GPU models might include the Display Power Saving Technology feature that can save the power consumption of the computer by optimizing picture contrast on the internal LCD.

This feature can be used if the computer is:

running in battery mode using the internal LCD display

The Display Power Saving Technology feature is enabled at factory default. To turn this feature off, change it in the settings accordingly in the Intel® HD Graphics Control Panel.

You can access this control panel in the following way:

Right-click on the desktop and click Graphics Properties...

2. Click Power and then click On Battery in the upper-left corner.

3. Click Disable under Display Power Saving Technology.

4. Click Apply. If you want to enable this feature, click Enable under Display Power

Saving Technology.

Power Condition Descriptions

The computer operating capability and battery charge status are affected by different power conditions, including whether an AC adaptor is connected and what the battery charge level is.

DC IN/Battery indicator

Check the DC IN/Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected. The following indicator conditions should be noted:

Flashing Amber The battery charge is low. The AC adaptor must

be connected to recharge the battery.

User's Manual 3-24

Amber Indicates that the AC adaptor is connected and

the battery is charging.

White Indicates that the AC adaptor is connected and

the battery is fully charged.

Flashing White Indicates a problem with the computer.

Disconnect the AC adaptor and remove the battery for several seconds. Then reinstall the battery and reconnect the AC adaptor. After that, press the power button. If it still does not operate properly, you should contact your reseller or dealer.

No light Under any other conditions, the indicator does

not light.

If the battery pack becomes too hot while it is being charged, the charge stops and the DC IN/Battery indicator goes out. When the temperature of the battery pack falls to a normal range, charging will resume. This process occurs regardless of whether the computer's power is on or off.

Power indicator

Check the Power indicator to determine the power status of the computer. The following indicator conditions should be noted:

White Indicates that power is being supplied to the

computer, and the computer is turned on.

Flashing Amber Indicates that the computer is in Sleep Mode and

that there is sufficient power available (AC adaptor or battery) to maintain this condition.

No light Under any other conditions, the indicator does

not light.

User's Manual 3-25

Chapter 4

Operating Basics

This chapter describes the basic operations of your computer, and highlights the precautions that must be taken when using it.

Using the Touch Screen (only for R30t-C/A30t-C)

Some models are equipped with a touch screen. You can use your finger to manipulate icons, buttons, menu items, the on-

screen keyboard, and other items on the touch screen.

Tap Simply tap your finger once on the touch screen

to activate an item, such as an app.

Press and hold Press your finger down and leave it there for a

few seconds. This shows information to help you learn more about an item or opens a menu specific to what you are doing.

Pinch or stretch Touch the screen or an item with two or more

fingers, and then move the fingers toward each other (pinch) or away from each other (stretch). This visually zooms in or out.

Rotate Put two or more fingers on an item and then turn

your hand to rotate things in the direction you turn your hand. Only some items can be rotated.

Slide Drag your finger on the touch screen to move

through what is on the screen.

Using the Touch Pad

The Touch Pad on the palm rest might support the following gestures:

User's Manual 4-

Tap Tap once on the Touch Pad to activate an item,

Pinch or stretch Place two or more fingers down on the Touch

Two-Finger Scroll Place two fingers down and slide them vertically

Do not put items on the Touch Pad surface to prevent abnormal action.

Some of the Touch Pad operations described in this section are only supported in certain applications.

The Keyboard

The number of keys available on your keyboard depends on which country/ region your computer is configured for, with keyboards being available for numerous languages.

There are different types of keys, specifically typewriter keys, function keys, Windows special keys, and the keypad overlay.

Never remove the key caps on your keyboard. Failure to do so might damage the parts under the key caps.

such as an app.

Pad and move them toward each other (pinch) or away from each other (stretch). This visually zooms in or out.

or horizontally from anywhere on the Touch Pad. This allows you to operate the scroll bars of a window.

Keyboard indicator

The following figure shows the position of the CAPS LOCK When the CAPS LOCK indicator glows, the keyboard produces capitals

when any letter is typed.

User's Manual 4-

indicator.

Figure 4-1 CAPS LOCK indicator (R30-C/A30-C)

1. CAPS LOCK indicator

Product appearance depends on the model you purchased.

CAPS LOCK This indicator glows green when letter keys are

locked into their uppercase format.

Function Keys

The function keys (F1 ~ F12) are the12 keys at the top of your keyboard.

Function keys let you enable or disable certain features of the computer. The functions can be performed by pressing the associated function keys.

Key Combination Function

FN + F1 Enters ''Lock computer mode''.

To restore your desktop, you need to log on again.

FN + F2 Switches between the power plans.

FN + F3 Switches the system to Sleep Mode.

FN + F4 Switches the system to Hibernation Mode.

FN + F5 Changes the active display device.

To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device.

FN + F6 Decreases the brightness of the display panel in

individual steps.

FN + F7 Increases the brightness of the display panel in

individual steps.

FN + F8 Turns the Airplane mode on or off.

FN + F9 Enables or disables the Touch Pad.

User's Manual 4-3

FN + F10 Turns on Arrow Mode.

Key Combination Function

FN + F11 Turns on Numeric Mode.

FN + F12 Locks the cursor on a specific line.

FN + ESC Turns the sound on or off.

FN + 1 Reduces the icon size on the desktop or the font

sizes within one of the supported application windows.

FN + 2 Enlarges the icon size on the desktop or the font

sizes within one of the supported application windows.

FN + 3 Decreases the volume of the computer.

FN + 4 Increases the volume of the computer.

FN + 5 Switches between available cooling methods for

the current power plan. This function is supported with some models.

FN + Space Changes the display resolution.

FN + Z (

)

Toggles the mode of the keyboard backlight between Timer, On, and Off.

To set up the brightness, click Start

Programs -> TOSHIBA -> Tools & Utilities -> HWSetup. Click Keyboard tab, and select a level

under Keyboard Backlight Brightness Control. To set up the timer, launch the BIOS setup utility,

select Power Management -> Keyboard Backlight Control Mode, and select TIMER. Adjust the timer under Backlight Lighting Time.

This function is supported with some models.

Flash Cards

Flash Cards makes it visual and easy to access and use the function keys. Normally the cards are hidden from view. To activate and use the Flash Cards, do the following:

Standard F1-F12 mode

Press and hold the FN key.

1. Flash Cards appears on top of the screen by default.

2. Press the function key or click the card associated with the desired function.

The selected card with available options appears.

-> All

User's Manual 4-

3. Press the function key repeatedly to cycle through the available options and release the FN key when the desired option is selected.

You can also click the desired option.

Special function mode

Press the function key repeatedly to cycle through the available

1. options and release it when the desired option is selected.

For more information, refer to the TOSHIBA Flash Cards Help file. To access this help, click Start -> All Programs -> TOSHIBA -> Tools &

Utilities -> Flash Cards. In the Settings for Flash Cards window, click the Help button.

Sticky key

You can use the TOSHIBA Accessibility utility to make the FN key sticky, that is, you can press it once, release it, and then press a desired function key. To start the TOSHIBA Accessibility utility, click Start -> All Programs

-> TOSHIBA -> Tools & Utilities -> Accessibility.

Windows special keys

The keyboard provides two keys that have special functions in Windows, the Windows® logo key activates the Start menu while the application key has the same function as the secondary (right) mouse button.

This key activates the Windows Start menu.

This key has the same function as the secondary (right) mouse button.

Using the AccuPoint

To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer.

Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad.

Some models are equipped with an AccuPoint.

AccuPoint precautions

Certain conditions can affect the on-screen pointer when using AccuPoint. For example, the pointer might travel contrary to AccuPoint operation or an error message might appear, if

You touch the AccuPoint during power-up. You apply constant, soft pressure during power-up. There is a sudden temperature change.

User's Manual 4-

Strong stress is applied to the AccuPoint.

If an error message appears, reboot the computer. If an error message does not appear, wait a moment for the pointer to stop, then continue operation.

Replacing the cap

The AccuPoint cap is an expendable item that should be replaced after prolonged use.

To remove the AccuPoint cap, gently dig the cap out (with finger).

Figure 4-2 Removing the AccuPoint cap (R30-C/A30-C)

1. AccuPoint cap

Product appearance depends on the model you purchased.

Position a new cap on the peg and press it into place.

The peg is square, so be careful to align the cap’s square hole with the peg.

You can buy replacement AccuPoint caps from your TOSHIBA authorized dealer.

Using the Fingerprint Sensor

Some models have a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authentication feature, it is no longer necessary to input the password from the keyboard. Fingerprint feature enables you to:

Logon to Windows and access a security enabled homepage through Internet Explorer.

Files and folders can be encrypted/decrypted and third party access to them prevented.

Unlock the password-protected screen-saver. Authentication of the User Password (and, if applicable, the HDD/SSD

Password) when booting up the computer (Pre-Boot authentication). Single Sign-On feature

User's Manual 4-

Fingerprint cannot be used in models that do not have a fingerprint module

installed.

How to Swipe your Finger

Using the following steps when swiping fingers for fingerprint registration or authentication can help to minimize authentication failures:

Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible. In performing this process, you should also take care to ensure that the center of your fingerprint is on the sensor.

The following illustrations show the recommended way to swipe your finger over the fingerprint sensor.

Figure 4-3 Swipe the finger

1. Sensor

Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping. Either of these conditions might cause fingerprint reading to fail.

Check the center of the fingerprint whorl before swiping and then ensure this is swiped along the center line of the sensor.

There is a possibility of authentication failures if the finger is swiped too quickly or too slowly. Follow any on-screen instructions to adjust the speed used during the swipe process.

Points to note about the Fingerprint Sensor

Be aware of the following considerations when using the fingerprint sensor. A failure to follow these guidelines might result in damage to the sensor, sensor failure, fingerprint recognition problems or a lower fingerprint recognition success rate.

Do not scratch or poke the sensor with your nails or any hard or sharp objects.

Do not press the sensor strongly.

User's Manual 4-

Do not touch the sensor with a wet finger or any wet objects. Keep the sensor surface dry and free from water vapor.

Do not touch the sensor with a soiled or dirty finger as minute foreign particles of dust and dirt might scratch it.

Do not paste stickers or write on the sensor. Do not touch the sensor with a finger or any other object which might

have a build-up of static electricity on it.

Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition.

Wash and dry your hands thoroughly. Remove static electricity from your fingers by touching any metal

surface. Static electricity is a common cause of sensor failures, especially when the weather is dry.

Clean the sensor with a lint-free cloth. Do not use detergent or any other chemicals to clean the sensor.

Avoid the following finger conditions for enrollment or recognition as they might result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate

Soaked or swollen finger, for example as might occur after taking a bath.

Injured finger Wet finger Soiled or oily finger Extremely dry skin condition on finger

Observe the following to improve the fingerprint recognition success rate.

Enroll two or more fingers. Enroll additional fingers if a recognition failure often occurs when using

already enrolled fingers. Check the condition of your finger. Any conditions which have

changed since enrollment, such as injury, rough skin, and extremely dry, wet, soiled, dirty, oily, soaked or swollen fingers, might lower the recognition success rate. Also if the fingerprint is worn down or the finger becomes thinner or fatter, the recognition success rate might be lowered.

As the fingerprint for each finger is different and unique you should ensure that only the registered or enrolled fingerprint or fingerprints are used for identification.

Check the position and speed at which you swipe your finger across the sensor. Refer to the preceding drawing.

The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. However, there might be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.

The recognition success rate might differ from user to user.

User's Manual 4-

Points to note about Fingerprint Utility

If Windows file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software.

You can back up the fingerprint data or the information registered to Web Site Passwords.

Use Import/Export in TOSHIBA Fingerprint Utility main menu. Also refer to the fingerprint utility Help file for more information by

clicking ?

in TOSHIBA Fingerprint Utility main menu.

Fingerprint utility limitations

TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free, or that it will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software.

The recognition success rate might differ from user to user.

Set up Fingerprint Registration

Use the following procedure when first using fingerprint authentication.

In use, the fingerprint authentication system uses the same username and password as defined within the Windows operating system. If no Windows password has been configured, you must do this before starting the fingerprint registration process.

This sensor has the memory space for at least twenty fingerprint patterns. You might be able to register more fingerprint patterns depending on the sensor memory usage.

1. Click Start Fingerprint Utility.

2. The Enroll screen is displayed. Enter the current account password into the Windows Password field. If no Windows password has been configured, you will be asked to configure the new logon password. Then click Next.

3. Click the non-enrolled finger you want to register and then click Next.

4. The instructions for enrollment operation screen is displayed. Carefully read them and then click Next.

User's Manual 4-

-> All Programs -> TOSHIBA -> Tools & Utilities ->

5. The scanning practice screen is displayed. You are able to practice swiping (three times) your finger to ensure you use the correct method. When you have finished practicing swiping your finger, click Next.

Swipe four times with the same finger. If scanning of fingerprint

6. succeeds, "Enrollment succeeded! Do you want to save this fingerprint?" message box appears. Click OK.

7. The following message appears: "It’s strongly recommended you enroll one more fingerprint.". Click OK and repeat Step 3, 4, 5 and 6 with another finger.

It is strongly recommended that you register 2 or more fingerprints.

You cannot enroll the same fingerprint more than once, even on a different user account.

Delete the Fingerprint Data

Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, please uninstall the application or delete all the logs created by the application.

Delete the fingerprint data for the currently logged in user

1. In the TOSHIBA Fingerprint Utility main menu, select Fingerprint Enroll.

2. In the Fingerprint Enroll window, it enables you to delete the fingerprint data for the currently logged in user. Click an enrolled finger you want to delete. "Do you want to delete?" message box appears on the screen and then click OK. If you want to delete other fingerprints, repeat this step. If only one fingerprint is registered, the message "At least one fingerprint is required." appears after clicking OK. You are not allowed to delete a unique fingerprint.

3. Click Close.

4. "Do you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu.

Delete all users fingerprints

1. In the TOSHIBA Fingerprint Utility main menu, click Run as administrator.

2. User Account Control window is displayed. Click Yes.

3. Swipe your enrolled finger.

4. Select Fingerprint Management option.

5. A list of fingerprint information for all users is shown in the screen. Click the enrolled fingerprint data you want to delete, and then click Delete Selected Items.

User's Manual 4-10

6. "Do you want to delete the selected fingerprints?" message box appears on the screen. Click OK.

Click Close.

8. "Do you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu.

Windows Logon via Fingerprint Authentication

In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows.

This is useful especially when many users are using the PCs, as user selection can be skipped.

Fingerprint Authentication Procedure

1. Start up the computer.

2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor. If authentication is successful, the user will be logged on to Windows.

If the fingerprint authentication fails, please logon using the Windows logon password.

A warning message will be displayed when authentication is abnormal or authentication is not successful within a fixed duration.

Fingerprint Pre-Boot authentication and Single SignOn feature

Overview about Fingerprint Pre-Boot authentication

The fingerprint authentication system can be used to replace the keyboard based User Password authentication system when booting up.

If you do not want to use the fingerprint authentication system for password authentication when booting up, but prefer to use the keyboard-based system instead, follow the on-screen instructions when the Fingerprint System Authentication screen is displayed. This will switch the password input screen across to the keyboard-based one.

You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint Pre-Boot authentication and its extended function to allow fingerprints to be used to access the computer when it is turned on.

When swiping your finger, ensure that you do it slowly and at a constant speed. If you find that this does not improve the authentication rate, you should try to adjust the speed at which the finger is swiped.

User's Manual 4-11

If there are any changes in the environment or settings related to authorization, you will be required to provide authorization information such as a User Password (and, if applicable, the HDD/SSD Password).

Overview about Fingerprint Single Sign-On feature

This is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD/SSD Password) and logging onto Windows using only one fingerprint authentication when booting up.

It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint Pre-Boot authentication and this Fingerprint Single Sign-On Feature. Use the TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password.

Only one fingerprint authentication is required to replace the User/BIOS Password (and, if applicable, the HDD/SSD Password) and the Windows Logon Password.

How to Enable Fingerprint Pre-Boot authentication and Single Sign-On feature

It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint Utility prior to enabling and configuring the Pre-Boot authentication and Single Sign-On feature. You should check that your fingerprint is enrolled before configuring the settings.

1. Logon as Administrator (means a user has administrator privileges).

2. In the TOSHIBA Fingerprint Utility main menu, click Run As Administrator.

3. User Account Control window is displayed. Click Yes.

4. Swipe your finger across the fingerprint sensor.

5. Select Setting in the main menu to open the Setting window. You can: Select Pre-Boot authentication check box if you want to use the

fingerprint Pre-Boot authentication feature. Select Pre-Boot authentication and Single Sign-On check boxes if

you want to use the Single Sign-On feature.

6. Click Apply.

7. "Save successfully" is displayed. Click OK.

8. Click Close.

9. "Do you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu.

This modified configuration for fingerprint Pre-Boot authentication and Single Sign-On feature becomes effective the next time the system is booted up.

User's Manual 4-12

Optical disc drive

For R30-C/A30-C: Some models are equipped with a DVD Super Multi drive or Blu-ray™ Writer drive. When the computer is accessing an optical disc, the indicator on the drive glows.

For R40-C/A40-C: Some models are equipped with a DVD Super Multi drive.

Formats

The drives support the following formats.

DVD Super Multi drive

The drive supports the following formats: CD-ROM, DVD-ROM, DVDVideo, CD-DA, CD-Text, Photo CD™ (single/multi-session), CD-ROM Mode 1/Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CDEXTRA), Addressing Method 2, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL (Format1), DVD+R DL.

Blu-ray™ Writer drive BDXL™

In addition to the above formats, Blu-ray™ Writer drive BDXL™ supports BD-ROM, BD-ROM DL, BD-R, BD-R DL, BD-RE, BD-RE DL,BD-R TL, BDR QL and BD-RE TL.

Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable.

Using the optical disc drive

The full-size drive provides high-performance execution of disc based programs. You can run either 12 cm (4.72") or 8 cm (3.15") discs without an adaptor.

For precautions on writing to discs, refer to the Writing discs section. To load discs, do the following:

When the computer’s power is on, press the eject button to open the disc tray slightly.

User's Manual 4-13

2. Grasp the disc tray gently and pull until it is fully opened.

Figure 4-4 Pressing the eject button and pulling the disc tray open (R30-C/A30-

1. Eject button 2. Disc tray

Product appearance depends on the model you purchased.

Lay the disc, label side up, in the disc tray.

Figure 4-5 Inserting a disc (R30-C/A30-C)

1. Laser lens

Product appearance depends on the model you purchased.

When the disc tray is fully opened, the edge of the computer covers the disc tray slightly. Therefore, you must to turn the disc at an angle when you place it in the disc tray. After seating the disc, however, make sure it lies flat.

Do not touch the laser lens or any portion of its surrounding casing as this might cause misalignment.

Prevent foreign objects from entering the drive. Check the surface of the disc tray, especially the area behind the front edge of the disc tray, to make sure there are no such objects before closing the drive.

4. Press gently at the center of the disc until you feel it click into place. The disc should lie below the top of the spindle, flush with the spindle base.

User's Manual 4-14

5. Push the center of the disc tray to close it. Press gently until it locks

Φ1.0mm

into place.

If the disc is not seated properly when the disc tray is closed, the disc might be damaged. Also, the disc tray might not open fully when you press the eject button.

Removing discs

To remove the disc, do the following:

Do not press the eject button while the computer is accessing the optical disc drive. Wait for the optical disc drive indicator to go out before you open the disc tray (only for R30-C/A30-C). Also, if the disc is spinning when you open the disc tray, wait for it to stop before you remove it.

1. To pop the disc tray partially open, press the eject button. Gently pull the disc tray out until it is fully opened.

When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open.

2. The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc.

Push the center of the disc tray to close it. Press gently until it locks

3. into place.

How to remove disc when the disc tray will not open

Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 20 mm) such as a straightened paper clip into the manual eject hole near the eject button.

Figure 4-6 Manual release with the eject hole (R30-C/A30-C)

1. Manual eject hole

Product appearance depends on the model you purchased.

User's Manual 4-15

Turn off the power before you use the manual eject hole. If the disc is spinning when you open the disc tray, the disc might fly off the spindle and cause injury.

Writable discs

This section describes the types of writable discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs.

CDs

CD-R discs can be written only once. The recorded data cannot be erased or changed.

CD-RW discs including multi speed CD-RW discs, high-speed CD-RW discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs

DVD-R, DVD+R, DVD-R DL and DVD+R DL discs can be written only once. The recorded data cannot be erased or changed.

DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.

Blu-ray™ discs

BD-R, BD-R DL discs can be written only once. The recorded data cannot be erased or changed.

BD-RE, BD-RE DL discs can be recorded more than once.

Writing discs

TOSHIBA Disc Creator is provided as writing software with this computer. This utility can be used to write data.

You can use the DVD Super Multi drive to write data to either CD-R, CDRW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW or DVD-RAM discs.

You can use the Blu-ray™ Writer drive BDXL™ to write data to either CDR, CD-RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW, DVD-RAM, BD-R, BD-R DL, BD-RE, BD-RE DL,BD-R TL, BD-R QL or BDRE TL discs.

When writing information to media using an optical drive, you should always ensure that you connect the AC adaptor to a live electrical outlet. It is possible that, if data is written while powered by the battery pack, the write process might sometimes fail due to low battery power. In these instances, data loss might occur.

User's Manual 4-16

Important message

Before you write or rewrite to any of the media supported by the optical disc drive, read and follow all of the setup and operating instructions in this section. If you fail to do so, you might find that the optical disc drive might not function properly, and you might fail to write or rewrite information successfully. This might cause you to either lose data or incur other damage to the drive or media.

Disclaimer

TOSHIBA does not assume responsibility for the following:

Damage to any disc that might be caused by writing or rewriting with this product.

Any change or loss of the recorded contents of media that might be caused by writing or rewriting with this product, or for any business profit loss or business interruption that might be caused by the change or loss of the recorded contents.

Damage that might be caused by using third party equipment or software.

Given the technological limitations of current optical disc writing drives, you might experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents.

Before writing or rewriting

Based on TOSHIBA limited compatibility testing, we suggest the following manufacturers of disc media, however, it must be noted that disc quality can affect write or rewrite success rates. Also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc.

CD-R:

TAIYO YUDEN CO., Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD.

CD-RW: (Multi-Speed, High-Speed and Ultra-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.

DVD-R:

DVD Specifications for Recordable Disc for General Version 2.0

TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media)

DVD-R DL:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)

User's Manual 4-17

DVD+R:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media)

DVD+R DL:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x speed media)

DVD-RW:

DVD Specifications for Recordable Disc for Version 1.1 or version

1.2

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 6x speed media)

DVD+RW:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)

DVD-RAM: (DVD Super Multi drive only)

DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2

Panasonic Corporation (for 3x and 5x speed media)

BD-R:

Panasonic Corporation

BD-R DL:

Panasonic Corporation

BD-RE:

Panasonic Corporation

BD-RE DL:

Panasonic Corporation

BD-R TL:

TDK.

BD-RE TL:

Panasonic Corporation

Some types and formats of DVD-R DL and DVD+R DL discs might be unreadable.

Disc created in DVD-R DL format4 (Layer Jump Recording) cannot be read.

When writing or rewriting

Observe the following points while you write or rewrite data to a media:

User's Manual 4-18

Always copy data from the internal storage drive to the optical media. Do not use the cut-and-paste function as the original data will be lost if there is a write error.

Do not perform any of the following actions:

Change users in the Operating Systems. Operate the computer for any other function, including such tasks

as using a mouse or Touch Pad, or closing/opening the display panel.

Start a communication application. Apply impact or vibration to the computer. Install, remove or connect external devices, including such items

as a memory media card, USB device, external monitor or an optical digital device.

Use the audio/video control button to reproduce music or voice. Open the optical disc drive.

Do not use shut down, log off, Sleep Mode or Hibernation Mode functions while writing or rewriting.

Make sure that the write/rewrite operation is completed before going into either Sleep Mode or Hibernation Mode (You can remove an optical media on the optical disc drive after writing is completed).

If the media is of poor quality, or is dirty or damaged, writing or rewriting errors might occur.

Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. In addition, do not use the computer on an unstable surface such as a stand.

Keep mobile phones and other wireless communication devices away from the computer.

TOSHIBA Disc Creator

Be aware of the following limitations when you use the TOSHIBA Disc Creator:

DVD Video cannot be created using TOSHIBA Disc Creator. DVD Audio cannot be created using TOSHIBA Disc Creator. You cannot use the "Audio CD" function of TOSHIBA Disc Creator to

record music to DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, or DVD+RW media.

Do not use the "Disc Backup" function of TOSHIBA Disc Creator in order to copy DVD Video or DVD-ROM material that has copyright protection.

DVD-RAM discs cannot be backed up using the "Disc Backup" function of TOSHIBA Disc Creator.

You cannot back up CD-ROM, CD-R, or CD-RW media to DVD-R, DVD-R DL, or DVD-RW media using the "Disc Backup" function of TOSHIBA Disc Creator.

User's Manual 4-19

You cannot back up CD-ROM, CD-R, or CD-RW media to DVD+R, DVD+R DL, or DVD+RW media using the "Disc Backup" function of TOSHIBA Disc Creator.

You cannot back up DVD-ROM, DVD Video, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, or DVD+RW to CD-R or CD-RW media using the "Disc Backup" function of TOSHIBA Disc Creator.

TOSHIBA Disc Creator cannot record in packet format. You might not be able to use the "Disc Backup" function of TOSHIBA

Disc Creator to back up a DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, or DVD+RW disc that was made with other software on a different optical media recorder.

If you add data to a DVD-R, DVD-R DL, DVD+R, or DVD+R DL disc that you have already recorded to, you might not be able to read the added data under some circumstances. For example, it cannot be read under 16-bit operating systems, such as Windows 98SE and Windows Me, while in Windows NT4 you need Service Pack 6 or later, and in Windows 2000, you need Service Pack 2. In addition to this, some DVD-ROM and DVD-ROM/CD-R/RW drives cannot read this added data regardless of the operating system.

TOSHIBA Disc Creator does not support recording to DVD-RAM discs. To achieve this, you should use Windows Explorer or another similar utility.

When you back up a DVD disc, be sure that the source drive supports recording to DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, or DVD+RW media. If this is not the case, then the source disc might not be backed up correctly.

When you back up a DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, or DVD+RW disc, be sure to use the same type of disc.

You cannot partially delete any data written to a CD-RW, DVD-RW, or DVD+RW disc.

Data Verification

To verify that data has been written or rewritten correctly to a data disc, do the following before you begin the write/rewrite process:

1. Click Start -> All Programs -> TOSHIBA -> Media & Entertainment

-> Disc Creator to access the TOSHIBA Disc creator utility.

2. Display the setting dialog box by one of the following two steps: Click the Recording settings button (

) for writing on the main

toolbar in the Data CD/DVD mode. Select Settings for Each Mode

-> Data CD/DVD in the Settings

menu.

3. Mark the Verify Written Data check box.

4. Select File Open or Full Compare mode.

5. Click the OK button.

User's Manual 4-20

How to learn more about TOSHIBA Disc Creator

Refer to the Help files for additional TOSHIBA Disc Creator information.

TOSHIBA VIDEO PLAYER

TOSHIBA VIDEO PLAYER is only provided with some models. Please be aware of the following limitations when you use the TOSHIBA

VIDEO PLAYER:

Notes on use

This software can only be used on Windows operating system. TOSHIBA VIDEO PLAYER software is supported for playback of DVD

and video file. Frame dropping, audio skipping or out of sync audio and video might

occur during playback of some video titles. Close all other applications when using the TOSHIBA VIDEO

PLAYER. Do not open any other applications or carry out any other operations during video playback. Playback might stop or not function properly in some situations.

Unfinalized DVDs created on home DVD recorders might not be playable on the computer.

Use DVD-Video discs with a region code which is either "the same as the factory default setting" (if applicable) or "ALL".

Do not play back video while watching or recording television programs using other applications. Failure to do so might cause video playback or television program recording errors. In addition, if prescheduled recording starts during video playback it might cause video playback or television program recording errors. Please view video during times when there is no recording prescheduled.

The resume function cannot be used with some discs on the TOSHIBA VIDEO PLAYER.

It is recommended that the AC adaptor is connected when playing video. Power-saving features might interfere with smooth playback. When playing video using battery power, set the Power Options to "Balance".

The screen saver is disabled during video playback using the TOSHIBA VIDEO PLAYER. The computer will not automatically go into Hibernation, Sleep, or shutdown mode.

Do not configure the Display automatic power off function to run while the TOSHIBA VIDEO PLAYER is running.

Do not switch to Hibernation or Sleep Mode when running the TOSHIBA VIDEO PLAYER.

Do not lock the computer using the Windows logo ( ) + L keys when running the TOSHIBA VIDEO PLAYER. The TOSHIBA VIDEO PLAYER does not have a parental control

function.

User's Manual 4-21

In order to protect copyrights, the Windows Print Screen function is disabled when TOSHIBA VIDEO PLAYER is running.

(Print Screen functions are disabled even when running other applications besides TOSHIBA VIDEO PLAYER and when TOSHIBA VIDEO PLAYER is minimized.) Please close the TOSHIBA VIDEO PLAYER to use the Print Screen function.

Carry out the installation/uninstallation of the TOSHIBA VIDEO PLAYER under a user account with administrator rights.

Do not change Windows Users while TOSHIBA VIDEO PLAYER is running.

For some DVD or video files, using the control window to change the audio track will also change the subtitle track.

This software can only play back MPEG2, MP4 and WTV files created by the preinstalled applications on the same computer. Playback might not function properly if you use the files other than these types.

The playback of some media files might not be normal by this player. This might also happen when using Windows Media Player and Video app.

Display Devices & Audio

If the video image is not displayed on an external display or television, stop the TOSHIBA VIDEO PLAYER, and change the screen resolution. To change the screen resolution, click Start -> Control

Panel -> Appearance and Personalization resolution. However, video cannot be output to some external

displays and televisions due to output or playback conditions. When viewing video on an external display or TV, change the display

device before playing. Video can be played only on internal LCD displays or external displays. In Clone mode (Dual View), TOSHIBA VIDEO PLAYER might not function properly.

Do not change the screen resolution while running the TOSHIBA VIDEO PLAYER.

Do not change the display device while running the TOSHIBA VIDEO PLAYER.

-> Display -> Adjust

Starting TOSHIBA VIDEO PLAYER

Use the following procedure to start TOSHIBA VIDEO PLAYER.

Insert a DVD-Video in the optical disc drive while the operating system is running.

When a DVD-Video disc is set in the DVD drive (for models with DVD drive), TOSHIBA VIDEO PLAYER might start automatically.

2. Click Start -> All Programs -> TOSHIBA -> Media & Entertainment

-> TOSHIBA VIDEO PLAYER to start TOSHIBA VIDEO PLAYER.

User's Manual 4-22

Operating TOSHIBA VIDEO PLAYER

Notes on Using TOSHIBA VIDEO PLAYER.

Screen display and available features may vary amongst videos and scenes.

If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, Touch Pad and mouse menu operations may not be able to be used.

Open TOSHIBA VIDEO PLAYER Manual

TOSHIBA VIDEO PLAYER features and instructions are explained in details in TOSHIBA VIDEO PLAYER Manual. Use the following procedure to open TOSHIBA VIDEO PLAYER Manual.

Press the F1 key when TOSHIBA VIDEO PLAYER is launched and click the Help button.

TOSHIBA Blu-ray Disc Player

Please be aware of the following limitations when you use TOSHIBA Bluray Disc Player.

Notes on Use

This software can only be used on Windows operating system. TOSHIBA Blu-ray Disc Player is only provided with models configured

with a Blu-ray™ Writer drive. Playback of high bit rate content might cause frame dropping, audio

skipping or decrease in computer performance. Close all other applications before playing back video. Do not open

any other applications or carry out any other operations during video playback.

Do not switch to Hibernation or Sleep Mode when running the TOSHIBA Blu-ray Disc Player.

Because Blu-ray Disc™ playback operates according to programs built into the content, operation methods, operation screens, sound effects, icons and other features might vary from disc to disc. For more information on these items refer to instructions included with content or contact the content manufacturers directly.

Make sure to connect the AC adapter of the computer when playing a video.

TOSHIBA Blu-ray Disc Player supports AACS (Advanced Access Control System) copy protection technology. Renewal of the AACS key integrated into this product is required for uninterrupted enjoyment of Blu-ray Disc™. An Internet connection is required for renewal.

User's Manual 4-23

AACS key renewal is provided free of charge for 5 years after the purchase of this product, however renewal beyond 5 years is subject to conditions specified by the software provider, TOSHIBA Corporation.

Do not play back video while recording television programs using other applications. Failure to do so might cause video playback or television program recording errors. In addition, if pre-scheduled recording starts during video playback it might cause video playback or television program recording errors. Please view video during times when there is no recording prescheduled.

While playing a BD-J title, keyboard shortcut is ineffective. Resume play function cannot be used with some discs on TOSHIBA

Blu-ray Disc Player. The interactive function on Blu-ray™ discs might not work depending

on the contents or network situation. Blu-ray™ drives and their associated media are manufactured

according to the specifications of three marketing regions. Region codes can be set from TOSHIBA Blu-ray Disc Player. (Click the Setting button in the Display Area. And click the Region Menu). When you purchase Blu-ray™ Video, make sure it matches your drive, otherwise it will not play properly.

To play back video on an external display or TV using TOSHIBA Bluray Disc Player, use output devices like external displays or TV that have HDCP supported HDMI port. The video cannot be displayed on an external display or TV connected to the RGB connector.

The Blu-ray Disc™ movie can be played only on internal LCD displays or external devices connected via an HDMI output. In Clone mode (Dual View), TOSHIBA Blu-ray Disc Player might not function properly.

This product does not play HD DVD discs. Blu-ray™ discs with high definition content are required for HD viewing.

The playback of some media files might not be normal by this player. This might also happen when using Windows Media Player and Video app.

Display Devices & Audio

If the video image is not displayed on an external display or television, stop the TOSHIBA Blu-ray Disc Player, and change the screen resolution. To change the screen resolution, click Start -> Control

Panel -> Appearance and Personalization resolution. However, video cannot be output to some external

displays and televisions due to output or playback conditions.

User's Manual 4-24

-> Display -> Adjust

When viewing video on an external display or TV, change the display device before playing. Video can be played only on internal LCD displays or external displays. In Clone mode (Dual View), TOSHIBA Blu-ray Disc Player might not function properly.

Do not change the screen resolution while running the TOSHIBA Bluray Disc Player.

Do not change the display device while running the TOSHIBA Blu-ray Disc Player.

Starting TOSHIBA Blu-ray Disc Player

Use the following procedure to start TOSHIBA Blu-ray Disc Player.

Insert a Blu-ray™ Movie Disc in the optical disc drive while the operating system is running.

When a Blu-ray™ Movie Disc is set in the Blu-ray™ drive (for models with Blu-ray™ drive), TOSHIBA Blu-ray Disc Player might start automatically.

Click Start

-> TOSHIBA Blu-ray Disc Player.

-> All Programs -> TOSHIBA -> Media & Entertainment

Operating TOSHIBA Blu-ray Disc Player

Notes on using TOSHIBA Blu-ray Disc Player.

Screen display and available features might vary amongst Blu-ray™ Videos and scenes.

If the menu is opened in the Display Area using the Control Panel's Top Menu or Menu buttons, Touch Pad and mouse menu operations might not be able to be used.

Open TOSHIBA Blu-ray Disc Player Manual

TOSHIBA Blu-ray Disc Player features and instructions are explained in details in TOSHIBA Blu-ray Disc Player Manual.

Use the following procedure to open TOSHIBA Blu-ray Disc Player Manual.

Press the F1 key when TOSHIBA Blu-ray Disc Player is launched and click the Help button.

Battery

This section explains battery types, use, recharging methods and handling.

Battery types

The computer has different types of batteries.

User's Manual 4-25

Battery pack

When the AC adaptor is not connected, the main power source of the computer is a removable lithium ion battery pack, also referred to in this manual as the main battery. You can purchase additional battery packs for extended use of the computer away from an AC power source although you should not change the battery pack while the AC adaptor is connected.

Before you remove the battery pack, save your data and shut down the computer, or place the computer into Hibernation Mode. Be aware that, when placing the computer into Hibernation Mode, the contents of memory are saved to the internal storage drive, although for safety sake, it is best to also save your data manually.

Real-Time Clock (RTC) battery

The Real-Time Clock (RTC) battery provides power for the internal realtime clock and calendar function and also maintains the system configuration while the computer is turned off. If the RTC battery becomes completely discharged, the system will lose this information and the realtime clock and calendar will stop working.

You can change the Real-Time Clock settings in the TOSHIBA Setup Utility. Refer to Real-Time Clock for further information.

The RTC battery of the computer must be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled, or disposed of. Dispose of the battery as required by local ordinances or regulations.

Care and use of the battery pack

This section provides the important safety precautions in order to handle your battery pack properly.

Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions.

Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation might generate smoke or fire, or cause the battery pack to rupture.

Keep the battery pack out of reach of infants and children. It can cause injury.

The battery pack can explode if not replaced, used, handled or disposed of properly. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.

User's Manual 4-26

Charge the battery pack only in an ambient temperature from 5 through 35 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate, and the battery life might be shortened.

Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor. Never remove the battery pack while the computer is in Sleep Mode, as data might be lost.

Never remove the battery pack while the Wake-up on LAN function is enabled, as data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function.

Charging the batteries

When the power in the battery pack becomes low, the DC IN/Battery indicator flashes amber to indicate that only a few minutes of battery power remain. If you continue to use the computer while the DC IN/Battery indicator flashes, the computer enters Hibernation Mode so that you do not lose any data, and automatically turn itself off.

You must recharge the battery pack when it becomes discharged.

Procedures

To recharge a battery pack, connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet. The DC IN/Battery indicator glows amber while the battery is being charged.

Use only the computer connected to an AC power source or optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.

Charging Time (R30-C/A30-C)

The following table shows the approximate time required to charge an exhausted battery fully.

Battery type Power off Power on

Battery pack (45 Wh, 4 cell)

RTC battery Does not

User's Manual 4-27

about 3.5 hours about 3.5 ~ 10 hours

Does not charge

charge

Charging Time (R40-C/A40-C)

The following table shows the approximate time required to charge an exhausted battery fully.

Battery type Power off Power on

Battery pack (45 Wh, 4 cell)

about 3.0 hours about 3.0 ~ 10 hours

RTC battery Does not

charge

Be aware that the charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you are using the computer. If you make heavy use of external devices for example, the battery might scarcely charge at all during operation.

Does not charge

Charging notice

The battery might not begin charging immediately under the following conditions:

The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, charge it at room temperature of between 5°C to 35°C (41°F to 95°F).

The battery is nearly completely discharged. In this instance, leave the AC adaptor connected for a few minutes and the battery should begin charging.

The DC IN/Battery indicator might show a rapid decrease in battery operating time when you try to charge a battery under the following conditions:

The battery has not been used for a long time. The battery has completely discharged and been left in the computer

for a long time.

In such cases, do the following:

Fully discharge the battery by leaving it in the computer with the power on until the system automatically turns itself off.

2. Connect the AC adaptor to the DC IN 19V jack of the computer, and to a wall outlet that is supplying power.

3. Charge the battery until the DC IN/Battery indicator glows white.

Repeat these steps two or three times until the battery recovers normal capacity.

Monitoring battery capacity

Remaining battery power can be monitored using the following methods.

User's Manual 4-28

Clicking the battery icon on the Windows Taskbar Via the Battery Status in the Windows Mobility Center window

Wait several seconds to monitor the remaining operating time because the computer needs time to check the remaining capacity of the battery pack and then calculate the remaining operating time, based on this together with the current power consumption.

Be aware that the actual remaining operating time might differ slightly from the calculated time.

With repeated discharges and recharges, the battery capacity will gradually decrease. In view of this, it is noted that an often used, older battery will not operate for as long as a new battery even when both are fully charged.

Maximizing battery operating time

The usefulness of a battery depends on how long it can supply power on a single charge, while how long the charge lasts in a battery depends on:

Processor speed Screen brightness Internal storage drive power off period How often and for how long you use the internal storage drive and

external disk drives, for example, optical disc How much charge the battery contained to begin with How you use optional devices, such as a USB device, to which the

battery supplies power Where you store your programs and data Whether you close the display panel when you are not using the

keyboard - closing the display saves power The environmental temperature - operating time decreases at low

temperatures System Sleep Mode System Hibernation Mode Display power off period Whether you enable Sleep Mode, which can conserve battery power if

you are frequently turning the computer off and on The condition of the battery terminals. Always ensure the terminals

stay clean by wiping them with a clean dry cloth before installing the battery pack

Batteries exhausted time (R30-C/A30-C)

When you turn off the power of your computer with batteries fully charged, the batteries exhaust within the following approximate period.

User's Manual 4-29

Battery type Sleep Mode Shut Down Mode

Battery pack (45 Wh, 4 cell)

RTC battery about 7 years about 7 years

about 3 days about 65 days

Batteries exhausted time (R40-C/A40-C)

When you turn off the power of your computer with batteries fully charged, the batteries exhaust within the following approximate period.

Battery type Sleep Mode Shut Down Mode

Battery pack (45 Wh, 4 cell)

RTC battery about 8 years about 8 years

about 4 days about 60 days

Extending battery life

To maximize the life of your battery packs, do the following at least once a month.

Turn off the computer's power.

2. Disconnect the AC adaptor and turn on the computer's power. If it does not turn on then go to Step 4.

3. Operate the computer on battery power for five minutes. If you find that the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. However, if the DC IN/Battery indicator flashes or there is some other warning to indicate a low battery condition, go to Step 4.

4. Connect the AC adaptor to the DC IN 19V jack of the computer, and to a wall outlet that is supplying power. The DC IN/Battery indicator glows amber to indicate that the battery pack is being charged. However, if DC IN/Battery indicator does not glow, this indicates that power is not being supplied. Check the connections for the AC adaptor and the power cord.

5. Charge the battery pack until the DC IN/Battery indicator glows white.

Replacing the battery pack

Be aware that the battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through

repeated charging and discharging, and should be replaced when it reaches the end of its operating life. In addition to this, you might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source for an extended period of time.

User's Manual 4-30

This section explains how to remove and install the battery pack, and

begins with the removal process which is detailed through the following steps.

Do not remove the battery pack while the computer is in Sleep Mode, as data is stored in RAM, so if the computer loses power it might be lost.

In Hibernation Mode, data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed.

Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries.

Removing the battery pack

To remove a discharged battery, do the following:

1. Save your work.

2. Click Start, and click Shut down. Ensure that the Power indicator is off.

3. Remove all cables and peripherals that are connected to the computer.

4. Close the display panel and turn the computer upside down.

5. Slide the battery lock into its unlocked ( Slide and hold the battery release latch to disengage the battery pack

) position.

and then lift it up to remove it from the computer.

Figure 4-7 Releasing the battery pack (R30-C/A30-C)

1. Battery lock 3. Battery pack

2. Battery release latch

Product appearance depends on the model you purchased.

Installing the battery pack

To install a battery pack, do the following:

User's Manual 4-31

Do not touch the battery release latch while holding the computer or the

battery pack might fall out due to the unintentional release of the battery release latch and cause injuries.

1. Insert the battery pack as far as it will go into the computer. Ensure that the battery pack is securely in place and the battery lock is

2. in its locked (

Turn your computer over.

) position.

Wireless WAN Device (R30-C/A30-C)

Some models are equipped with the Wireless WAN device. This device gives you the ability for a high-speed connection to the Internet, corporate intranet, and your email while you are away from the office.

Installing a SIM card (R30-C/A30-C)

To install a SIM card, do the following:

1. Click Start, and click Shut down. Ensure that the Power indicator is off.

2. Remove the AC adaptor and all cables and peripherals connected to the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack.

5. Locate the SIM card slot.

6. To pop the SIM card tray partially open, insert a slender object (about 10mm, diameter 0.8mm), such as a straightened paper clip, into the eject hole. Gently pull to open the SIM card tray.

Never pull the SIM card tray completely out of the slot.

Figure 4-8 Open the SIM card tray with the eject hole (R30-C/A30-C)

1. Eject hole 3. SIM card

2. SIM card tray

Product appearance depends on the model you purchased.

User's Manual 4-32

7. Place the SIM card into the SIM card tray with the metal connectors facing up.

Insert the SIM card tray into the SIM card slot, and push the center of

8. the tray to close it. Press gently until it locks into place.

9. Install the battery pack.

Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.

Do not touch the connectors on the SIM card or on the computer. Debris on the connectors might cause access problems.

Removing a SIM Card (R30-C/A30-C)

To remove the SIM card, do the following:

Shut down the computer. Make sure the Power indicator is off.

2. Close the display panel.

3. Turn the computer upside down and remove the battery pack.

4. To pop the SIM card tray partially open, insert a slender object (about 10mm, diameter 0.8mm), such as a straightened paper clip, into the eject hole. Gently pull to open the SIM card tray.

5. Remove the SIM card from the SIM card tray.

6. Insert the SIM card tray back into the SIM card slot.

Wireless WAN Device (R40-C/A40-C)

Installing a SIM card (R40-C/A40-C)

To install a SIM card, do the following:

1. Click Start, and click Shut down. Ensure that the Power indicator is off.

2. Remove the AC adaptor and all cables and peripherals connected to the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack.

5. Locate the SIM card slot.

User's Manual 4-33

6. To pop the SIM card tray partially open, insert a slender object (about

10mm, diameter 0.8mm), such as a straightened paper clip, into the eject hole. Gently pull to open the SIM card tray.

Never pull the SIM card tray completely out of the slot.

Figure 4-9 Open the SIM card tray with the eject hole (R40-C/A40-C)

1. Eject hole

Product appearance depends on the model you purchased.

Place the SIM card into the SIM card tray with the metal connectors

7. facing up.

8. Insert the SIM card tray into the SIM card slot, and push the center of the tray to close it. Press gently until it locks into place.

9. Install the battery pack.

Figure 4-10 Installing the SIM Card (R40-C/A40-C)

1. SIM card tray 2. SIM card

Product appearance depends on the model you purchased.

User's Manual 4-34

Do not touch the connectors on the SIM card or on the computer. Debris on the connectors might cause access problems.

Removing a SIM Card

To remove the SIM card, do the following:

Shut down the computer. Make sure the Power indicator is off.

2. Close the display panel.

3. Turn the computer upside down and remove the battery pack.

4. To pop the SIM card tray partially open, insert a slender object (about 10mm, diameter 0.8mm), such as a straightened paper clip, into the eject hole. Gently pull to open the SIM card tray.

5. Remove the SIM card from the SIM card tray.

6. Insert the SIM card tray back into the SIM card slot.

GPS Function

Your computer might include a built-in GPS (Global Positioning System). The performance of GPS varies depending on the environment. Failure to

pinpoint a location might happen. Your current location might not be shown depending on the status of GPS

or the location. If you are obtaining your current location information from the computer, your current location might not be detected due to the information accuracy. Specifically, your current location might not be detected in the following places or situations:

Inside or directly under a building Inside a bag or box Among dense trees When there is an obstacle (person or object) in the front of the

antenna Underground tunnel, underground, or underwater Buildings, streets or residential areas Near to high voltage cables Bad weather, such as heavy rain or snow

Additional memory module (only for R30-C/A30C)

This section is only applicable for models equipped with the memory module cover.

You can install additional memory into the computer in order to increase the amount of system memory that is available. This section describes how to install and remove optional memory modules.

User's Manual 4-35

You should place a mat beneath the computer in order to prevent the computer's lid from scratches or damages when you are installing/ replacing the memory module. In this instance, you should avoid mats that are made of materials that hold or generate static electricity.

When installing or removing a memory module, you must ensure that you do not touch any other internal areas of the computer.

Use only memory modules approved by TOSHIBA.

Do not try to install or remove a memory module under the following conditions. a. The computer is turned on.

b. The computer was shut down in either Sleep or Hibernation Mode.

c. Wake-up on LAN is enabled.

d. The wireless communication function is on.

e. Sleep and Charge function is enabled.

Be careful not to let screws or other foreign matter fall into the computer. It might cause malfunction or electric shock.

Additional memory module is a precision electronic component that might be fatally damaged by static electricity. Since the human body can carry static electricity, it is important that you discharge yourself before touching or installing any additional memory modules. To discharge your body’s static electricity, simply touch any metal close to you with bare hands.

Use a point size 0 Phillips screwdriver to remove and fasten the screws. The use of an incorrect screwdriver can damage the screw heads.

Installing a memory module

To install a memory module, do the following:

Click Start, and click Shut down. Ensure that the Power indicator is

1. off.

2. Remove the AC adaptor, all cables, and peripherals connected to the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack.

5. Loosen the screws securing the memory module cover in place. Note that the screw is attached to the cover in order to prevent it from being lost.

User's Manual 4-36

6. Slide your fingernail or a thin object under the cover and lift it off.

Figure 4-11 Removing the memory module cover

1. Screws 2. Memory module cover

Product appearance depends on the model you purchased.

User's Manual 4-37

7. Align the notch of the memory module with that of the memory slot

and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place.

Figure 4-12 Seating the memory module

1. Notch 3. Slot B

2. Slot A

Product appearance depends on the model you purchased.

Do not touch the connectors on the memory module or on the computer. Debris on the connectors might cause memory access problems.

The slot A is reserved for the first memory module. Use the slot B for expanded memory. If only one module is installed, use the slot A.

Align the grooves along the edges of the memory module with the locking tabs on the connector and insert the module into the connector firmly. If you find it difficult to install the memory module, gently prise the locking tabs outwards using the tip of your finger.

Also ensure that you hold the memory module along its left and right hand edges - the edges with the grooves in.

User's Manual 4-38

8. Seat the memory module cover in place and secure it with the screw.

Ensure that the memory module cover is firmly closed.

Figure 4-13 Seating the memory module cover

1. Memory module cover 2. Screws

Product appearance depends on the model you purchased.

Install the battery pack.

10. Turn your computer over.

11. Connect the AC adaptor and turn on the computer. Make sure that the added memory is recognized. To confirm it, click Start -> Control Panel -> System and Security -> System.

Removing a memory module

To remove the memory module, do the following:

1. Click Start, and click Shut down. Ensure that the Power indicator is off.

2. Remove the AC adaptor, all cables, and peripherals connected to the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack.

5. Loosen the screw securing the memory module cover in place. Note that the screw is attached to the cover in order to prevent it from being lost.

6. Slide your fingernail or a thin object under the cover and lift it off.

7. Push the latches away from the module in order to release it. A spring forces one end of the module up at an angle.

User's Manual 4-39

8. Grasp the module by its edges and remove it from the computer.

If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them.

Do not touch the connectors on the memory module or on the computer. Debris on the connectors might cause memory access problems.

Figure 4-14 Removing the memory module

1. Latches

Product appearance depends on the model you purchased.

Seat the memory module cover in place and secure it with the screw.

Ensure that the memory module cover is firmly closed.

10. Install the battery pack.

11. Turn your computer over.

12. Connect the AC adaptor and turn the computer on.

LAN

The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).

This section describes how to connect/disconnect to a LAN.

The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.

User's Manual 4-40

The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on).

LAN cable types

The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings might cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.

If you are using Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T), be sure to connect with a CAT5e cable or higher. You cannot use a CAT3 or CAT5 cable.

If you are using Fast Ethernet LAN (100 megabits per second, 100BASETX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable.

If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable.

Connecting the LAN cable

To connect the LAN cable, do the following:

Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system might hang up.

Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage might occur.

Do not connect any power supplying device to the LAN cable that is connected to the LAN jack. Otherwise, malfunctions or damage might occur.

1. Turn off the power to all external devices connected to the computer.

User's Manual 4-41

2. Plug one end of the cable into the LAN jack. Press gently until you

hear the latch click into place.

Figure 4-15 Connecting the LAN cable (R30-C/A30-C)

Figure 4-16 Connecting the LAN cable (R40-C/A40-C)

1. LAN jack 2. LAN cable

Product appearance depends on the model you purchased.

Plug the other end of the cable into a LAN hub connector or router.

3. Check with your LAN administrator and hardware or software vendor before using or configuring a network connection.

Memory media

The computer is equipped with a memory media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants.

Keep foreign objects out of the memory media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or Keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.

An adaptor is required to use miniSD/microSD Card.

Not all memory media have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all memory media can operate properly.

User's Manual 4-42

Figure 4-17 Examples of memory media

Secure Digital (SD) Card microSD card adaptor and

microSD card

MultiMediaCard (MMC)

Points to note about the memory media card

SD/SDHC/SDXC memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or play back protected material on another computer or other device, and you cannot reproduce any copyrighted material except for your personal enjoyment.

The following is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards.

SD, SDHC and SDXC memory cards appear the same externally. However, the logo on memory cards is different, so pay careful attention to the logo when purchasing.

The SD memory card logo is ( ).

The SDHC memory card logo is ( ).

The SDXC memory card logo is ( ).

The maximum capacity of SD memory cards is 2 GB. The maximum capacity of SDHC memory cards is 32 GB. The maximum capacity of SDXC memory cards is 128 GB.

Memory media format

New media cards are formatted according to specific standards. If you wish to reformat a media card, be sure to do so with a device that uses media cards.

Formatting a memory media card

Memory media cards are sold already formatted in conformity to specific standards. If you reformat a memory card, be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards, not with the format command provided within Windows.

User's Manual 4-43

To format all areas of the memory card, including the protected area, you must obtain an appropriate application that applies the copy protection system.

Media care

Observe the following precautions when handling the card.

Do not twist or bend cards. Do not expose cards to liquids or store in humid areas or lay media

close to containers of liquid. Do not touch the metal part of a card or expose it to liquids or let it get

dirty. After using card, return it to its case. The card is designed so that it can be inserted only one way. Do not

try to force the card into the slot. Do not leave a card partially inserted in the slot. Press the card until

you hear it click into place. Set the write-protect switch to the lock position, if you do not want to

record data. Memory cards have a limited lifespan, so it is important to back up

important data. Do not write to a card if the battery power is low. Low power might

affect writing accuracy. Do not remove a card while read/write is in progress.

For more details on using memory cards, see manuals accompanying the cards.

About the write-protect feature

Memory media cards have a write-protect function.

SD Card (SD memory card, SDHC memory card and SDXC memory card)

Set the write-protect switch to the lock position, if you do not want to record data.

Inserting memory media

The following instructions apply to all types of supported media devices. To insert memory media, do the following:

Turn the memory media so that the contacts (metal areas) face down.

2. Insert the memory media into the memory media slot on your computer.

User's Manual 4-44

Dynabook Toshiba PS461E-0S70D3EN User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Copyright, Disclaimer and Trademarks

Copyright

Disclaimer

Trademarks

Regulatory Information

FCC information

EU Declaration of Conformity

Canadian regulatory information (Canada only)

Following information is only valid for EU-member States:

REACH - Compliance Statement

Following information is only for Turkey:

Following information is only for India:

Video Standard Notice

ENERGY STAR® Program

Disposing of the computer and the computer's batteries

Optical disc drive safety instructions

Location of the Required Label

Precautions

General Precautions

Provide adequate ventilation

Creating a computer-friendly environment

Stress injury

Heat injury

Pressure or impact damage

Cleaning the computer

Moving the computer

Mobile phones

Instruction Manual for Safety and Comfort

Safety Icons

Equipment checklist

Hardware

Documentation

Conventions

Short model name

Using your computer for the first time

Connecting the AC adaptor

Opening the display

Turning on the power

Initial setup

Turning off the power

Shut Down Mode

Restarting the computer

Sleep Mode

Hibernation Mode

System Recovery

System Recovery Options

Creating Recovery Media

Restoring the pre-installed software from your created Recovery Media

Restoring the pre-installed software from the Recovery Partition

The Grand Tour for R30-C/A30-C

Front with the display closed (R30-C/A30-C)

Left side (R30-C/A30-C)

Right side (R30-C/A30-C)

Back (R30-C/A30-C)

Underside (R30-C/A30-C)

Front with the display open (R30-C/A30-C)

The Grand Tour for R40-C/A40-C

Front with the display closed (R40-C/A40-C)

Left side (R40-C/A40-C)

Right side (R40-C/A40-C)

Back (R40-C/A40-C)

Underside (R40-C/A40-C)

Front with the display open (R40-C/A40-C)

Internal Hardware Components

Intel® Display Power Saving Technology

Power Condition Descriptions

DC IN/Battery indicator

Power indicator

Using the Touch Screen (only for R30t-C/A30t-C)

Using the Touch Pad

The Keyboard

Keyboard indicator

Function Keys

Flash Cards

Sticky key