Dynabook UPP20XWL User Manual

TOSHIBA 2010

Portable Personal Computer

User ’s Manual

© 2002 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

TOSHIBA 2010 Portable Personal Computer User’s Manual

First edition September 2002

Disclaimer

This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA 2010 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.

Trademarks

Intel and Pentium are registered trademarks and SpeedStep is a trademark of Intel Corporation. Windows and Microsoft are registered trademarks of Microsoft Corporation. Photo CD is a trademark of Eastman Kodak. Other trademarks and registered trademarks not listed above may be used in this manual.

FCC information

Product Name : Model number :

Portégé 2010

PP201

FCC notice "Declaration of Conformity Information"

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

❑ Reorient or relocate the receiving antenna. ❑ Increase the separation between the equipment and receiver. ❑ Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

❑ Consult the dealer or an experienced radio/TV technician for help.

WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port and microphone jack. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment. The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer.

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Contact

Address: TOSHIBA America Information Systems, Inc.

9740 Irvine Boulevard Irvine, California 92618-1697

Telephone: (949) 583-3000

EU Declaration of Conformity

TOSHIBA declares, that the product: PP201* conforms to the following Standards: Supplementary Information: “The product complies with the requirements

of the Low V oltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”

This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.

VCCI Class B Information

Modem warning notice

Conformity Statement

The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network (PSTN).

However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.

In the event of problems, you should contact your equipment supplier in the first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.

Germany ATAAB AN005,AN006,AN007,AN009,AN010 and

DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04 Portugal ATAAB AN001,005,006,007,011 and P03,04,08,10 Spain ATAAB AN005,007,012, and ES01 Switzerland ATAAB AN002 All other countries/regions ATAAB AN003,004 Specific switch settings or software setup are required for each network, please refer

to the relevant sections of the user guide for more details. The hookflash (timed break register recall) function is subject to separate national

type approvals. It has not been tested for conformity to national type regulations, and no guarantee of successful operation of that specific function on specific national networks can be given.

Japan regulations

Region selection

If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection.

Redial

Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.

Japan’s Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes.

The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.

A00-0940JP

Pursuant to FCC CFR 47, Part 68:

When you are ready to install or use the modem, call your local telephone company and give them the following information:

❑ The telephone number of the line to which you will connect the modem ❑ The registration number that is located on the device

The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main system label.

❑ The Ringer Equivalence Number (REN) of the modem, which can vary. For the

REN of your modem, refer to your modem’s label.

The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.

Type of service

Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.

Telephone company procedures

The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.

If problems arise

If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.

Disconnection

If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.

Fax branding

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other entity or individual. In order to program this information into your fax modem, you should complete the setup of your fax software before sending messages.

Instructions for IC CS-03 certified equipment

1 The Industry Canada label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection.

The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

2 The user manual of analog equipment must contain the equipment’s Ringer

Equivalence Number (REN) and an explanation notice similar to the following: The Ringer Equivalence Number (REN) of the modem, which can vary. For the

REN of your modem, refer to your modem’s label.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

3 The standard connecting arrangement (telephone jack type) for this equipment is

jack type(s): USOC RJ11C. The IC registration number of the modem is shown below.

Canada: 1353 11026A

Notes for Users in Australia and New Zealand

Modem warning notice for Australia

Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner. To verify that the country/region is correctly set, enter the command ATI which displays the currently active setting.

To set the country/region permanently to Australia, enter the following command sequence:

A T%TE=1 ATS133=1 AT&F AT&W A T%TE=0 ATZ

Failure to set the modem to the Australia country/region setting as shown above will result in the modem being operated in a non-compliant manner. Consequently, there would be no permit in force for this equipment and the Telecoms Act 1991 prescribes a penalty of $12,000 for the connection of non-permitted equipment.

Notes for use of this device in New Zealand

❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance

of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.

❑ In addition to satisfactory line conditions a modem can only work properly if:

a/ it is compatible with the modem at the other end of the call and b/ the application using the modem is compatible with the application at the

other end of the call - e.g., accessing the Internet requires suitable software in addition to a modem.

❑ This equipment shall not be used in any manner which could constitute a

nuisance to other Telecom customers.

❑ Some parameters required for compliance with Telecom’s PTC Specifications

are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications:

a/ There shall be no more than 10 call attempts to the same number within

any 30 minute period for any single manual call initiation, and

b/ The equipment shall go on-hook for a period of not less than 30 seconds

between the end of one attempt and the beginning of the next.

c/ Automatic calls to different numbers shall be not less than 5 seconds

apart.

❑ Immediately disconnect this equipment should it become physically damaged,

and arrange for its disposal or repair.

❑ The correct settings for use with this modem in New Zealand are as follows:

ATB0 (CCITT operation) AT&G2 (1800 Hz guard tone) AT&P1 (Decadic dialing make-break ratio =33%/67%) ATS0=0 (not auto answer) ATS10=less than 150 (loss of carrier to hangup delay, factory default of 15

recommended) ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)

❑ When used in the Auto Answer mode, the S0 register must be set with a value

of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the

modem answers. This confirms that the call has been successfully switched through the network.

(b) caller identification information (which occurs between the first and

second ring cadences) is not destroyed.

❑ The preferred method of dialing is to use DTMF tones (ATDT...) as this is

faster and more reliable than pulse (decadic) dialing. If for some reason you must use decadic dialing, your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand “Reverse Dialing” standard.

Number to be dialed: 0 1 2 3 4 5 6 7 8 9 Number to program into computer: 0 9 8 7 6 5 4 3 2 1 Note that where DTMF dialing is used, the numbers should be entered

normally.

❑ The transmit level from this device is set at a fixed level and because of this

there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.

❑ It is recommended that this equipment be disconnected from the Telecom line

during electrical storms.

❑ When relocating the equipment, always disconnect the Telecom line connec-

tion before the power connection, and reconnect the power first.

❑ This equipment may not be compatible with Telecom Distinctive Alert ca-

dences and services such as FaxAbility.

NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOM

General conditions

As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications.

The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The Telepermit may not be assigned to other parties or other products without Telecom approval.

A Telepermit artwork for each device is included from which you may prepare any number of Telepermit labels subject to the general instructions on format, size and colour on the attached sheet.

The Telepermit label must be displayed on the product at all times as proof to purchasers and service personnel that the product is able to be legitimately connected to the Telecom network.

The Telepermit label may also be shown on the packaging of the product and in the sales literature, as required in PTC 100.

The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original.

An invoice for $NZ1237.50 will be sent under separate cover.

Table of Contents

Preface

Manual contents ............................................................................... xix

Conventions ........................................................................................xx

Abbreviations .......................................................................................xx

Icons ................................................................................................... xx

Keys ................................................................................................... xx

Key operation ..................................................................................... xxi

Display ............................................................................................... xxi

Messages .......................................................................................... xxi

General Precautions

Stress injury .................................................................................... xxiii

Heat injury....................................................................................... xxiii

Pressure or impact damage .......................................................... xxiii

PC card overheating .......................................................................xxiv

Chapter 1 Introduction

Equipment checklist ..........................................................................1-1

Features ............................................................................................. 1-2

Special features ................................................................................. 1-6

Utilities................................................................................................ 1-8

Options ............................................................................................. 1-10

Chapter 2 The Grand Tour

Front with the display closed ........................................................... 2-1

Left side.............................................................................................. 2 -2

Right side ........................................................................................... 2-3

Back side............................................................................................ 2-4

Underside ...........................................................................................2-5

Front with the display open.............................................................. 2-6

Indicators............................................................................................ 2-8

High Capacity 2nd Battery Pack..................................................... 2-10

AC adaptor ....................................................................................... 2-11

xiii

Chapter 3 Getting Started

Setting up your work space.............................................................. 3-1

General conditions.............................................................................. 3-2

Placement of computer....................................................................... 3-2

Seating and posture ........................................................................... 3-3

Lighting .............................................................................................. 3-3

Work habits........................................................................................ 3-4

Opening the display ..........................................................................3-5

Connecting the AC adaptor .............................................................. 3-5

Turning on the power ....................................................................... 3-7

Windows XP Professional/2000 setup .............................................. 3-8

Turning off the power ....................................................................... 3-8

Shut Down mode (Boot mode) ............................................................ 3 -8

Hibernation mode ............................................................................... 3-9

Standby mode .................................................................................. 3-11

Restarting the computer ................................................................. 3-13

Restoring the preinstalled software from the Product

Recovery CD-ROM.................................................................... 3-14

Chapter 4 Operating Basics

Using the TouchPad ..........................................................................4-1

Using the USB FDD Kit ...................................................................... 4 -2

Connecting 3 1/2" diskette drive .........................................................4-3

Disconnecting 3 1/2" diskette drive ..................................................... 4-4

Diskette care...................................................................................... 4-4

Wireless communications................................................................. 4-4

Wireless LAN .....................................................................................4-5

Wireless communication switch ......................................................... 4-5

Wireless communication LED ............................................................ 4-5

LAN ..................................................................................................... 4-6

LAN cable types................................................................................. 4-6

Connecting cable................................................................................ 4-6

Disconnecting cable ........................................................................... 4-7

Using the internal modem ................................................................ 4-8

Region selection................................................................................. 4-8

Properties menu ................................................................................. 4-9

Connecting ....................................................................................... 4-11

Disconnecting................................................................................... 4-12

Cleaning the computer ................................................................... 4-12

xiv

Moving the computer ...................................................................... 4-12

Heat dispersal .................................................................................. 4-13

Chapter 5 The Keyboard

Typewriter keys ................................................................................. 5-1

F1 … F12 function keys ..................................................................... 5-2

Soft keys: Fn key combinations........................................................ 5-2

Emulating keys on enhanced keyboard .............................................. 5-2

Hotkeys.............................................................................................. 5-4

Fn Sticky key..................................................................................... 5-6

Windows special keys ....................................................................... 5-7

Keypad overlay.................................................................................. 5-7

Turning on the overlays ....................................................................... 5-7

Temporarily using normal keyboard (overlay on).................................. 5-8

Temporarily using overlay (overlay off) ................................................. 5-9

Temporarily changing modes ..............................................................5-9

Generating ASCII characters ............................................................ 5-9

Chapter 6 Power and Power-Up Modes

Power conditions............................................................................... 6-1

Power indicators ............................................................................... 6- 4

Battery indicators ............................................................................... 6-4

DC IN indicator ................................................................................... 6-4

Power indicator................................................................................... 6-5

Battery types ...................................................................................... 6-5

Main battery ....................................................................................... 6-5

Secondary battery ..............................................................................6-6

Real time clock battery....................................................................... 6-6

Care and use of the Battery Pack .................................................... 6-7

Safety precautions.............................................................................. 6-7

Charging the batteries ...................................................................... 6-10

Monitoring battery capacity .............................................................. 6-11

Maximizing battery operating time .................................................... 6-12

Retaining data with power off ............................................................ 6-13

Extending battery life........................................................................ 6-13

Replacing the Battery Pack ............................................................ 6-14

Main Battery Pack............................................................................ 6-14

High Capacity 2nd Battery Pack....................................................... 6-16

Starting the computer by password ............................................... 6-19

Power-up modes ............................................................................. 6-20

Windows utilities .............................................................................. 6-20

Hotkeys............................................................................................ 6-20

Panel power off ............................................................................... 6-20

System Auto Off ............................................................................... 6-20

Chapter 7 HW Setup and Passwords

HW Setup ........................................................................................... 7-1

Accessing HW Setup .........................................................................7-1

HW Setup window ..............................................................................7-2

Supervisor password....................................................................... 7-10

Chapter 8 Optional Devices

PC cards ............................................................................................. 8- 2

Installing a PC card ............................................................................ 8-2

Removing a PC card ........................................................................... 8 -4

SD cards ............................................................................................. 8- 5

Installing an SD card .......................................................................... 8-5

Removing an SD card .........................................................................8-6

Memory expansion............................................................................ 8-6

Installing memory module................................................................... 8-7

Removing memory module.................................................................. 8-9

Battery Pack..................................................................................... 8-10

High Capacity 2nd Battery Pack..................................................... 8-10

Universal AC Adaptor ...................................................................... 8-10

Battery Charger ............................................................................... 8-11

USB FDD Kit ..................................................................................... 8-11

Slim Port Replicator........................................................................ 8-11

Ports ................................................................................................ 8-11

High Capacity 2nd Battery Pack....................................................... 8-12

External monitor.............................................................................. 8-12

Security lock .................................................................................... 8-13

Chapter 9 Troubleshooting

Problem solving process................................................................... 9-1

Preliminary checklist ..........................................................................9-1

Analyzing the problem ........................................................................ 9-2

xvi

Hardware and system checklist........................................................ 9-3

System start-up.................................................................................. 9 -3

Self test.............................................................................................. 9-4

Power ................................................................................................. 9-4

Password ........................................................................................... 9-7

Keyboard............................................................................................ 9-8

LCD panel ..........................................................................................9-8

Hard disk drive.................................................................................... 9-9

Diskette drive.................................................................................... 9-10

Infrared port ...................................................................................... 9-10

Pointing device ................................................................................. 9-11

PC card ............................................................................................ 9-13

SD card ............................................................................................ 9-13

Monitor ............................................................................................. 9-14

Sound system .................................................................................. 9-14

USB ................................................................................................. 9-15

Modem ............................................................................................. 9-15

LAN .................................................................................................. 9-17

Wireless LAN ................................................................................... 9-17

TOSHIBA support ............................................................................. 9-18

Before you call ................................................................................. 9-18

Where to write .................................................................................. 9-18

Appendixes

Appendix A

Specifications ................................................................................... A-1

Appendix B

Display Controller and Modes ......................................................... B-1

Appendix C

AT Commands .................................................................................. C-1

Appendix D

S-registers ......................................................................................... D-1

Appendix E

V.90.....................................................................................................E-1

Appendix F

Wireless LAN......................................................................................F-1

xvii

Appendix G

AC Power Cord and Connectors...................................................... G-1

Appendix H

Internal Modem Guide ..................................................................... H-1

Appendix I

Parts Numbers ....................................................................................I-1

Glossary

Index

xviii

Preface

Congratulations on your purchase of the TOSHIBA 2010 computer. This powerful, lightweight notebook computer is designed to provide years of reliable, highperformance computing.

This manual tells how to set up and begin using your 2010 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you’re new to portable computing, first read over the Introduction and The Grand Tour chapters to familiarize yourself with the computer’s features, components and accessory devices. Then read Getting Started for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the preface to learn how this manual is organized, then become acquainted with this manual by browsing through its pages. Be sure to look over the Special features section of the Introduction, to learn about features that are uncommon or unique to the computers and carefully read HW Setup and Passwords. If you are going to install PC cards or connect external devices such as a monitor, be sure to read Chapter 8, Optional

Devices.

Manual contents

This manual is composed of nine chapters, nine appendixes, a glossary, and an index.

Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and options.

Chapter 2, The Grand Tour, identifies the components of the computer and briefly explains how they function.

Chapter 3, Getting Started, provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area.

Chapter 4, Operating Basics, includes instructions on using the following devices: TouchPad, external diskette drive, wireless communication features, LAN and internal modem.

Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hotkeys.

xix

User's Manual

Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes.

Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password.

Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on how to perform some

diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.

The Appendixes provide technical information about your computer. The Glossary defines general computer terminology and includes a list of acronyms

used in the text. The Index quickly directs you to the information contained in this manual.

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on.

Keys

The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key.

Conventions

Key operation

Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.

ABC When procedures require an action such as clicking an icon or entering

text, the icon’s name or the text you are to type in is represented in the type face you see to the left.

Display

ABC Names of Windows® or icons or text generated by the computer that

appears on its display screen is presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.

CAUTION: Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.

NOTE: Please read. A note is a hint or advice that helps you make best use of your equipment.

xxi

User's Manual

xxii

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.

Be certain to read the general precautions below and to note the cautions included in the text of the manual.

Stress injury

Carefully read the Instruction Manual for Safety & Comfort. It contains information on prevention of stress injuries to your hands and wrists than can be caused by extensive keyboard use. Chapter 3, Getting Started, also includes information on work space design, posture and lighting that can help reduce physical stress.

Heat injury

❑ Avoid prolonged physical contact with the computer. If the computer is used

for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, or if you keep your hands on the palm rest, for example) your skin might suffer low-heat injury.

❑ If the computer has been used for a long time, avoid direct contact with the

metal plate supporting the I/O ports. It can become hot.

❑ The surface of the AC adaptor can become hot when in use. This condition

does not indicate a malfunction. If you need to transport the AC adaptor, disconnect it and let it cool before moving it.

❑ Do not lay the AC adaptor on a material that is sensitive to heat. The material

could be damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact. Excessive pressure or impact can cause damage to computer components or otherwise cause malfunctions.

xxiii

User's Manual

PC card overheating

Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time.

xxiv

Chapter 1

Introduction

Equipment checklist ........................................................................... 1-1

Features .............................................................................................. 1-2

Special features .................................................................................. 1-6

Utilities................................................................................................. 1-8

Options .............................................................................................. 1-10

NTRODUCTION

INTRODUCTION

Chapter 1

Introduction

This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories.

CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA.

Equipment checklist

Carefully unpack your computer. Save the box and packing materials for future use. Check to make sure you have all the following items:

❑ PORTÉGÉ 2010 Portable Personal Computer ❑ Universal AC Adaptor and power cord ❑ High Capacity 2nd Battery Pack (option with some models, which come with a

standard Battery Pack)

❑ Modular cable The computer is configured with one of two sets of preinstalled software, manual

packages and auxiliary media depending on your choice of operating system. “Windows XP” is the Microsoft® Windows® XP Professional operating system. “Windows 2000” is the Microsoft® Windows® 2000 Professional operating

system. ❑ The following software is preinstalled:

• Microsoft® Windows XP Professional/2000

• TOSHIBA Wireless LAN Driver

• TOSHIBA Software Modem Driver

• TOSHIBA SD card Driver

• TOSHIBA Utilities

• TOSHIBA Hotkey Utility for Display Devices

• TOSHIBA Power Saver

• TOSHIBA Mobile Extension

NTRODUCTION

1-1

User's Manual

• TOSHIBA Common Modules

• TOSHIBA Controls

• TOSHIBA Console

• TOSHIBA Client Manager

INTRODUCTION

• TOSHIBA Network Device Switch

• SPANworks 2000 Professional

• TOSHIBA Skins for Windows Media Player

• Online manual

❑ Documentation:

• 2010 Portable Personal Computer User’s Manual

• Microsoft Windows XP Professional/2000 manual package

• Instruction Manual for Safety & Comfort

• End User License Agreement

• International Limited Warranty (ILW) Instruction

(This instruction is included only with computers sold in ILW supported areas.)

❑ Product Recovery CD-ROM (contains TOSHIBA Management Console and

TOSHIBA TouchPad On/Off Utility, which are not preinstalled)

If any of the items are missing or damaged, contact your dealer immediately.

Features

The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits:

Processor

Built-in Ultra Low Voltage Mobile Intel® Pentium® III processor

866 MHz-M with Enhanced Intel® SpeedStep™ Technology incorporates a math coprocessor and 32 KB cache.

1-2

Features

Memory

Built-in 256 MB of memory is installed on the main board.

Slots A 256 MB memory module can be installed in the memory

slot for a maximum of 512 MB system memory.

Level 2 cache A 512 KB level 2 cache is provided to maximize perfor-

mance.

Video RAM 16 MB of RAM is provided for video display.

(occupied from system memory)

Disks

Built-in Hard disk

40 billion bytes (37.26 GB)

Display

The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability.

Built-in 12.1" XGA-TFT, 1024 horizontal x 768 vertical pixels, up

to 16 M colors

Graphics controller A 128-bit graphics controller maximizes display

performance. Refer to Appendix B for more information.

NTRODUCTION

Keyboard

TouchPad

Built-in 84 keys or 85 keys, compatible with IBM enhanced

keyboard, embedded numeric overlay, dedicated cursor control, and keys.

Built-in A TouchPad and control buttons in the palm rest enable

control of the on-screen pointer and scrolling of windows.

1-3

User's Manual

Power

Battery Pack The computer is powered by one rechargeable lithium-ion

polymer Battery Pack.

INTRODUCTION

High Capacity 2nd This Battery Pack (PA3155U) increases your computer’s

Battery Pack operating time when a main Battery Pack is also installed.

RTC battery The internal RTC battery backs up the Real Time Clock

(RTC) and calendar.

AC adaptor The universal AC adaptor provides power to the system

and recharges the batteries when they are low. It comes with a detachable power cord. Because it is universal, it can receive a range of AC voltage between 100 and 240 volts.

Ports

Headphone Enables connection of a stereo headphone

Microphone Enables connection of a monaural microphone

Infrared This infrared port is compatible with Infrared Data

Association (IrDA 1.1) Fast InfraRed (FIR) standards. It enables cableless 4 Mbps data transfer with IrDA 1.1 compatible external devices.

External monitor 15-pin, analog VGA port supports VESA DDC2B compat-

ible functions.

Docking Special port for connecting an optional Slim Port Replicator

or High Capacity 2nd Battery Pack.

Universal Serial Bus The computer has two Universal Serial Bus ports that

(USB 2.0) comply with the USB 2.0 standard, which enables data

transfer speeds 40 times faster than the USB 1.1 standard. (The ports also support USB 1.1.)

Slots

1-4

PC card A PC card slot accommodates:

One 5 mm Type II Refer to Chapter 8, Optional Devices, for details.

SD card The SD card slot accommodates:

SD cards Refer to Chapter 8, Optional Devices, for details.

Features

Multimedia

Sound System Windows Sound System compatible sound system

provides internal speaker as well as jacks for an external microphone and headphone.

Communications

Modem An internal modem provides capability for data and fax

communication. It supports V.90. Refer to Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets.

L AN The computer is equipped with a LAN card that supports

Ethernet LAN (10 Mbit/s, 10BASE-T) and Fast Ethernet LAN (100 Mbit/s, 100BASE-Tx). It is preinstalled as a standard device in some markets.

Wireless LAN In some markets, the computer is equipped with a Wireless

LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with the IEEE 802.11 Standard (Revision B). It supports data transfer up to 11 Mbit/s. It has Frequency Channel Selection (2.4 GHz) and allows roaming over multiple channels.

TOSHIBA Console Press this button to launch an application automatically.

button In W indows XP/2000 the default is TOSHIBA Console.

Use the TOSHIBA Control to associate an application to this button.

Internet button Press this button to launch an Internet browser. See

Chapter 2, Grand Tour, for details.

NTRODUCTION

Security

Security lock slot Connects an optional security lock to anchor the computer

to a desk or other large object

1-5

User's Manual

Software

Operating System One of the following operating systems are available

Windows XP/2000. Refer to the preinstalled software

INTRODUCTION

TOSHIBA Utilities A number of utilities and drivers are preinstalled to make

Plug and Play When you connect an external device to the computer or

section at the front of this chapter.

your computer more convenient to use. Refer to the Utilities section in this chapter.

when you install a component, Plug and Play capability enables the system to recognize the connection and make the necessary configurations automatically.

Special features

The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use.

Hotkeys Key combinations let you quickly modify the system

configuration directly from the keyboard without running a system configuration program.

Keypad overlay Gray keys with gray lettering make up the keypad overlay,

which lets you use the keyboard for ten-key operations or cursor control.

Display automatic This feature automatically cuts off power to the internal

power off display when there is no keyboard input for a time

specified. Power is restored when any key is pressed. You can specify the time in the Turn off monitor item of the Power Save Mode window in Power Saver.

HDD automatic This feature automatically cuts off power to the hard disk

power off drive when it is not accessed for a time specified. Power is

restored when the hard disk is accessed. You can specify the time in the Turn off hard disks item of the Power Save Mode window in Power Saver.

System automatic This feature automatically turns off power to the system

power off when there is no input for a time specified. You can specify

the time in the System standby or System hibernate item of the System Power Mode window in Power Saver.

1-6

Special features

Battery save mode This feature lets you save battery power. You can specify

the Power Save Mode in the Running on batteries item of the Power Save Modes window in Power Saver.

Power on password Two levels of password security are available: supervisor

and user. This feature prevents unauthorized access to your computer.

Instant security A hotkey function blanks the screen and disables the

computer providing quick and easy data security.

Panel power on/off This feature turns power to the computer off when the

display panel is closed and turns it back on when the panel is opened. You can specify the setting in the When I close the lid item of the System Power Mode window in Power Saver.

Auto power on This feature lets you set a time and date for the computer

to turn on automatically. The feature is useful for receiving remote communications while you are asleep or away. You can specify the setting in Scheduled Tasks.

Standby If you have to interrupt your work, you can turn off the

power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off.

Hibernation This feature lets you turn off the power without exiting

from your software. The contents of main memory is saved to the hard disk, when you turn on the power again, you can continue working right where you left off.

NTRODUCTION

1-7

User's Manual

Heat dispersal To protect from overheating, the CPU has an internal

temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. Use the Fan item of the

INTRODUCTION

Power Save Modes window in Power Saver. Maximum Turns on fan first, then if necessary

Performance lowers CPU processing speed. Performance Uses a combination of fan and

lowering the CPU processing speed.

Battery optimized Lowers the CPU processing speed

first, then if necessary turns on the fan.

Utilities

This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme files.

TOSHIBA Power Saver To access this power savings management program in

Windows 2000, open the Control Panel and double-click the TOSHIBA Power Saver icon. In Windows XP, open the Control Panel, click Performance and Maintenance and click the TOSHIBA Power Saver icon.

HW Setup This program lets you customize your hardware settings

according to the way you work with your computer and the peripherals you use. To start the utility in Windows 2000, open the Control Panel and double-click the TOSHIBA HW Setup icon. In Windows XP, open the Control Panel, click Printers and Other Hardware and click the TOSHIBA HW Setup icon.

Fn-esse This Windows program lets you define your own “short-

cut” keys to quickly launch applications and speed your work in Windows. To start the utility, click the Windows Start button, point to Programs (Windows XP only, point to All Programs), point to TOSHIBA Utilities and click Fnesse.

Supervisor Password This utility for Windows lets you register a Supervisor

Utility for Windows Password, which restricts access to HW Setup.

1-8

Utilities

Display Driver The display driver enables simultaneous display on the

for Windows internal LCD, and on an external computer monitor. To

enable this function, use the Display Properties dialogue box.

Sound drivers A broad range of audio controls are possible through the

ALi sound driver, including Software Synthesize, Mic volume and Power management. Click Control Panel and click the ALi sound setup icon to adjust power management settings.

For other sound settings, use the Windows Device Manager, Multimedia panel or volume control dial.

LAN drivers This preinstalled driver makes the computer LAN-ready for

a computer running Windows 2000. To make LAN settings, click Start, point to Settings, click Control Panel and double-click the Network icon.

TOSHIBA Accessibility This utility lets you make the Fn key sticky, that is, you

can press it once, release it, and they press an “F number” key. The Fn key remains active until another key is pressed.

Hotkey utility This utility lets you display or hide a confirmation message

when you press Fn + F3 or Fn + F4.

TOSHIBA Controls Use this utility to customize TOSHIBA Console button

settings.

TOSHIBA Console TOSHIBA Console is a graphical user interface that

provides easy access to help and services. It is the default function launched by the TOSHIBA Console button.

Network Device The Network Device Switch enables quick and easy setup

Switch of Internet and network settings. The Network Device

Switch manages profiles captured from the computer settings for each network that you use. When you select a profile, your network settings change. To access this utility click Start, point to All Programs and click Network Device Switch.

NTRODUCTION

1-9

User's Manual

Options

You can add a number of options to make your computer even more powerful and convenient to use. The following options are available:

INTRODUCTION

Memory expansion One memory expansion slot is available for installing a 256

MB memory module. The module is SD Random Access Memory (SD-RAM).

Battery Pack An Battery Pack (PA3154U) can be purchased from your

TOSHIBA dealer. The Battery Pack is identical to the one that came with your computer. Use it as a spare or replacement.

High Capacity 2nd This Battery Pack (PA3155U) increases your computer’s

Battery Pack operating time when a main Battery Pack is also installed.

Universal AC Adaptor If you use your computer at more than one site, it may be

convenient to purchase an additional Universal AC Adaptor for each site so you will not have to carry the adaptor with you.

USB FDD Kit A 3 1/2" diskette drive accommodates 1.44-megabyte or

720-kilobyte diskettes. It connects to a USB port. (You cannot format 720-kilobyte diskettes on Windows XP, but you can use previously formatted disks.)

Battery Charger The Battery Charger lets you charge extra batteries outside

the computer. It must be used with the Battery Charge cable that is supplied only with the Slim Port Replicator. See chapter 8, Optional Devices, for details.

Security lock A slot is available to attach a security cable to the com-

puter to deter theft.

Slim Port Replicator The Slim Port Replicator provides the following: an external

monitor port, four USB ports, a port for charging a High Capacity 2nd Battery Pack, a LAN jack and a DC-IN socket.

1-10

Chapter 2

The Grand Tour

Front with the display closed ............................................................ 2-1

Left side............................................................................................... 2- 2

Right side ............................................................................................ 2 -3

Back side............................................................................................. 2-4

Underside ............................................................................................2-5

Front with the display open............................................................... 2-6

Indicators............................................................................................. 2-8

High Capacity 2nd Battery Pack...................................................... 2-10

AC adaptor ........................................................................................ 2-11

RAND

OUR

THE GRAND TOUR

Chapter 2

The Grand Tour

This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer.

RAND

Front with the display closed

Figure 2-1 shows the computer’s front with its display panel in the closed position.

POWER SOURCE/SYSTEM INDICATORS

DISPLAY LATCH

Figure 2-1 Front of the computer with display closed

Display latch This latch secures the LCD panel in its closed position.

Push the latch to open the display.

Power source/ LEDs let you monitor the status of various computer

system indicators functions. Details are given in the Indicators section.

OUR

2-1

User's Manual

Left side

Figure 2-2 shows the computer’s left side.

SECURITY LOCK SLOT

SD CARD INDICATOR

FAN VENT

Figure 2-2 The left side of the computer

THE GRAND TOUR

Security lock A security cable attaches to this slot. The optional security

slot cable anchors your computer to a desk or other large object

to deter theft.

Fan vent Provides air flow for the fan.

CAUTION: Be careful not to block the fan vent. Also be careful to keep foreign objects out of the vents. A pin or similar object can damage the computer’s circuitry.

SD card slot This slot lets you transfer data from the device to your

computer.

CAUTION: Keep foreign objects out of the SD card slot. A pin or similar object can damage the computer’s circuitry.

SD card indicator This indicator glows green when the computer is

accessing the SD card Slot.

SD CARD SLOT

2-2

Right side

Figure 2-3 shows the computer’s right side.

WIRELESS COMMUNICATION SWITCH

HEADPHONE JACK

communication Slide it to the left to turn off the functions. (This switch

MICROPHONE JACK

Figure 2-3 The right side of the computer

Wireless Slide this switch to the right to turn on Wireless LAN.

switch is only on models with Wireless LAN functions.)

Off On

Headphone jack A standard 3.5 mm mini headphone jack enables connec-

tion of a stereo headphone (16 ohm minimum) or other device for audio output. When you connect headphones, the internal speaker is automatically disabled.

PC CARD SLOT

INFRARED PORT

Right side

RAND

OUR

Microphone jack A standard 3.5 mm mini microphone jack enables connec-

tion of a monaural microphone or other device for audio input.

Infrared port This infrared port is compatible with Infrared Data Associa-

tion (IrDA 1.1) standards. It enables cableless 4 Mbps,

1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or

9.6 kbps data transfer with IrDA 1.1 compatible external devices.

PC card slot A PC card slot can accommodate one 5 mm PC card (Type

II). The slot supports 16-bit PC cards and CardBus PC

CAUTION: Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry.

cards.

2-3

User's Manual

Back side

Figure 2-4 shows the computer’s back side.

LAN INDICATOR

EXTERNAL MONITOR PORT

THE GRAND TOUR

MODEM JACK

Modem jack In areas where an internal modem is installed as standard

CAUTIONS: 1. In case of a lightning storm, unplug the modem cable

LAN jack This jack lets you connect to a LAN. The adaptor has

Ether

LAN indicator This indicator glows green when the computer is

Universal Two Universal Serial Bus ports are on the left side. The

Serial Bus ports comply with the USB 2.0 standard, which enables

(USB 2.0) ports data transfer speeds 40 times faster than the USB 1.1

LAN JACK

Figure 2-4 The computer’s back side

equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line. The modem is not supported in some marketing regions.

from the telephone jack.

2. Do not connect the modem to a digital telephone line. A digital line will damage the modem.

built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx).

accessing the LAN.

standard. (The ports also support USB 1.1.)

USB PORTS

DC IN 15V

CAUTION: Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry.

NOTE: Operation of all functions of all USB devices has not been confirmed. Some functions might not execute properly.

2-4

Underside

External monitor This 15-pin port lets you connect an external monitor.

port

DC IN 15V The AC adaptor connects to this socket. Use only the

DC IN 15V

model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer.

Underside

RAND

Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer.

BATTERY

LOCK

DOCKING

HOLES

DOCKING

PORT

MEMORY MODULE

COVER

DOCKING

HOLE

SPEAKER

BATTERY PACK

Figure 2-5 The underside of the computer

Docking port Use this port to connect an optional Slim Port Replicator or

High Capacity 2nd Battery Pack.

CAUTION: Keep foreign objects out of the docking port. A pin or similar object can damage the computer’s circuitry.

Docking holes These holes ensure a proper connection between the

computer and a High Capacity 2nd Battery Pack.

Expansion Use this socket to install a memory module to increase

memory socket your computer’s memory by 256 MB. Refer to the Memory

expansion section in Chapter 8, Optional Devices.

OUR

2-5

User's Manual

Battery Pack The Battery Pack powers the computer when the AC

adaptor is not connected. The Batteries section in Chapter 6, Power and Power-Up Modes, describes how to access the Battery Pack. Battery Packs can be purchased from your TOSHIBA dealer to extend the computer’s battery operating time.

Battery lock A sliding lock prevents inadvertent release of the Battery

Pack.

Speaker The speaker emits sound generated by your software as

well as audio alarms, such as low battery condition,

THE GRAND TOUR

generated by the system.

Front with the display open

Figure 2-6 shows the front of the computer with the display open. To open the display, push the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle.

DISPLAY SCREEN

DISPLAY

HINGE

POWER

BUTTON

2-6

INTERNET

BUTTON

TOSHIBA CONSOLE

BUTTON

TOUCHPAD

TOUCHPAD CONTROL BUTTONS

Figure 2-6 The front with the display open

DISPLAY HINGE

SENSOR

SWITCH

Front with the display open

Display screen The full-color LCD displays high-contrast text and

graphics and is compatible with the industry standard Video Graphics Array (VGA). The LCD consists of up to 1024 × 768 pixels or dots. The computer has a Thin-Film Transistor (TFT) display. Refer to Appendix B.

When the computer operates on power through the AC adaptor, the display screen’s image will be somewhat brighter than when it operates on battery power. The lower brightness level is intended to save battery power.

Display hinge The display hinge holds the display screen at easy-to-view

angles.

Power button Press the power button to turn the computer’s power on

and off.

Internet button Press this button to launch an Internet browser. If the

computer’s power is off, you can press this button to turn on the computer’s power and launch the browser automatically in one step.

TOSHIBA Console Press this button to launch an application automatically.

button The default is TOSHIBA Console.

RAND

OUR

TouchPad A TouchPad located in the center of the palm rest is used

to control the on-screen pointer. Refer to the Using the TouchPad section in Chapter 4, Operating Basics.

TouchPad Control buttons below the TouchPad let you select menu

control buttons items or manipulate text and graphics designated by the

on-screen pointer.

Sensor switch This switch shuts down the computer when you close the

cover and the panel power on/off feature is enabled.

2-7

User's Manual

Indicators

Figure 2-7 shows the indicators, which light when various computer operations are in

THE GRAND TOUR

progress.

POWER

MAIN

BATTERY

SECONDARY

BATTERY

DC IN

Figure 2-7 The power source/system indicators

DISK

WIRELESS

COMMUNICATION

Power source/system indicators

DC IN The DC IN indicator glows green when DC power is

supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.

Power The Power indicator glows green when the computer is

on. If you select Standby from Shut Down Windows, this indicator flashes orange (one second on, two seconds off) while the computer shuts down.

Main battery The Main battery indicator shows the condition of the

charge. Green means fully charged and orange means being charged. Refer to Chapter 6, Power and Power-Up Modes.

Secondary The Secondary battery indicator shows the condition of

battery the charge of a High Capacity 2nd Battery Pack. Green

means fully charged and orange means being charged.

Refer to Chapter 6, Power and Power-Up Modes.

2-8

Indicators

Disk The Disk indicator glows green when the computer is

accessing a disk drive.

Wireless The Wireless communication indicator lights when the

communication Wireless LAN function is turned on. (This indicator is used

only models with Wireless LAN functions.)

The figures below show the positions of the keypad overlay indicators and the CapsLock indicator.

When the F10 key indicator glows, the keypad overlay lets you control the cursor. When the F11 key indicator glows, the keypad overlay lets you enter numbers.

NUMERIC MODE

ARROW MODE

RAND

OUR

Figure 2-8 Keypad overlay indicators

When the CapsLock indicator glows, the keyboard is in all-caps mode.

CAPS LOCK

Figure 2-9 CapsLock indicator

2-9

User's Manual

Keyboard indicator

Caps Lock This indicator glows green when the alphabet keys are

locked in uppercase.

Arrow mode When the Arrow mode indicator lights green, you can

use the keypad overlay (white labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard.

Numeric mode You can use the keypad overlay (white labeled keys) for

numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard.

THE GRAND TOUR

High Capacity 2nd Battery Pack

You can install a High Capacity 2nd Battery Pack in the computer. A High Capacity 2nd Battery Pack (PA3155U) is seated in a base that fits beneath the computer. It provides about twice the power and operating time as the standard Battery Pack. Refer to the Replacing the Battery Pack section in Chapter 6, The Power and Power-Up Modes.

NOTE: The High Capacity 2nd Battery Pack is provided as standard equipment with some models. You can purchase optional High Capacity 2nd Battery Packs from your dealer.

Figure 2-10 The High Capacity 2nd Battery Pack

2-10

AC adaptor

The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region.

To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6 Power and Power-Up Modes for details.

RAND

OUR

Figure 2-11 The AC adaptor

CAUTION: Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case.

2-11

User's Manual

THE GRAND TOUR

2-12

Chapter 3

Getting Started

Setting up your work space.........................................................3-1

General conditions.........................................................................3-2

Placement of computer..................................................................3-2

Seating and posture ......................................................................3-3

Lighting .........................................................................................3-3

Work habits...................................................................................3-4

Opening the display .....................................................................3-5

Connecting the AC adaptor .........................................................3-5

Turning on the power ..................................................................3-7

Windows XP Professional/2000 setup .........................................3- 8

Turning off the power ..................................................................3-8

Shut Down mode (Boot mode) .......................................................3-8

Hibernation mode ..........................................................................3-9

Standby mode ............................................................................. 3-11

Restarting the computer ............................................................ 3-13

Restoring the preinstalled software from the Product

Recovery CD-ROM...............................................................3-14

ETTING

TARTED

GETTING STARTED

Chapter 3

Getting Started

This chapter provides basic information to get you started using your computer. It covers the following topics:

❑ Setting up your work space — for your health and safety

NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

❑ Opening the display ❑ Connecting the AC adaptor ❑ Turning on the power ❑ Windows XP Professional/2000 setup ❑ Turning off the power ❑ Restarting the computer ❑ Restoring the preinstalled software from the Product Recovery CD-ROM

If you are a new user, follow the steps in each section of this chapter as you prepare to operate your computer.

NOTE: All users should read the section Windows XP Professional/2000 setup.

Setting up your work space

Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation. This section discusses the following topics:

❑ General conditions ❑ Placement of the computer ❑ Seating and posture

ETTING

TARTED

3-1

User's Manual

❑ Lighting ❑ Work habits

General conditions

In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment.

❑ Make sure there is adequate space around the computer for proper ventilation. ❑ Make sure the AC power cord connects to an outlet that is close to the

computer and easily accessible.

❑ The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees

Fahrenheit) and the relative humidity should be 20 to 80 percent.

❑ Avoid areas where rapid or extreme changes in temperature or humidity may

occur.

❑ Keep the computer free of dust, moisture, and exposure to direct sunlight. ❑ Keep the computer away from heat sources, such as electric heaters. ❑ Do not use the computer near liquids or corrosive chemicals. ❑ Do not place the computer near objects that create strong magnetic fields

GETTING STARTED

(e.g., stereo speakers).

❑ Do not operate the computer in close proximity to a mobile phone. ❑ Leave ample ventilation room for the fan. Do not block the vents.

Placement of the computer

Position the computer and peripheral devices to provide comfort and safety. ❑ Set the computer on a flat surface at a comfortable height and distance. The

display should be no higher than eye level to avoid eye strain.

❑ Place the computer so that it is directly in front of you when you work and

make sure you have adequate space to easily operate other devices.

❑ Allow adequate space behind the computer to let you freely adjust the

display. The display should be angled to reduce glare and maximize visibility.

❑ If you use a paper holder, set it at about the same height and distance as the

computer.

3-2

Setting up your work space

Seating and posture

The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1.

BELOW EYE LEVEL

ETTING

FOOT REST

Figure 3-1 Posture and positioning of the computer

❑ Place your chair so that the keyboard is at or slightly below the level of your

elbow. You should be able to type comfortably with your shoulders relaxed.

❑ Your knees should be slightly higher than your hips. If necessary, use a foot

rest to raise the level of your knees to ease pressure on the back of your thighs.

❑ Adjust the back of your chair so it supports the lower curve of your spine. ❑ Sit straight so that your knees, hips and elbows form approximately 90 degree

angles when you work. Do not slump forward or lean back too far.

90O ANGLES

Lighting

Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect

off the screen. Use tinted windows, shades or other screen to eliminate sun glare.

TARTED

3-3

User's Manual

❑ Avoid placing the computer in front of bright light that could shine directly in

your eyes.

❑ If possible, use soft, indirect lighting in your computer work area. Use a lamp to

illuminate your documents or desk, but be sure to position the lamp so that it does not reflect off the display or shine in your eyes.

Work habits

A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.

❑ Sit in a relaxed posture. Good positioning of your chair and equipment as

described earlier can reduce tension in your shoulders or neck and ease back strain.

❑ Vary your posture frequently. ❑ Occasionally stand up and stretch or exercise briefly. ❑ Exercise and stretch your wrists and hands a number of times during the day. ❑ Frequently, look away from the computer and focus your eyes on a distant

GETTING STARTED

object for several seconds, for example 30 seconds every 15 minutes.

❑ Take frequent short breaks instead of one or two long breaks, for example, two

or three minutes every half hour.

❑ Have your eyes examined regularly and visit a doctor promptly, if you suspect

you might be suffering from a repetitive strain injury.

A number of books are available on ergonomics and repetitive strain injury or repetitive stress syndrome. For more information on these topics or for pointers on exercises for such stress points as hands and wrists, please check with your library or book vendor. Also refer to the computer’s Instruction Manual for Safety & Comfort.

3-4

Connecting the AC adaptor

Opening the display

The display panel can be rotated in a wide range of angles for optimal viewing.

1. Push down the display latch on the front of the computer to unlatch the display panel.

2. Lift the panel up and adjust it to the best viewing angle for you.

NOTE: When you open the display, hold it with both hands and lift up slowly.

ETTING

TARTED

Figure 3-2 Opening the display panel

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the Battery Pack will need to be charged before you can operate from battery power.

The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the Battery Pack, refer to Chapter 6, Power and Power-Up Modes.

3-5

User's Manual

1. Connect the power cord to the AC adaptor.

Figure 3-3 Connecting the power cord to the AC adaptor

2. Connect the AC adaptor’s DC output plug to the DC IN port on the back of the computer.

GETTING STARTED

Figure 3-4 Connecting the adaptor to the computer

3. Plug the power cord into a live wall outlet. The Battery and DC IN indicator on the front of the computer should glow.

3-6

Turning on the power

This section describes how to turn on the power.

NOTE: After you turn on the power for the first time, do not turn it off until you have set up the operating system (OS) and the OS has started up.

1. If the external diskette drive is connected, make sure it is empty. If a diskette is in the drive, press the eject button and remove the diskette.

2. Open the display panel.

3. Press and hold the button for two or three seconds.

ETTING

TARTED

Figure 3-5 Turning on the power

3-7

User's Manual

Windows XP Professional/2000 setup

When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Professional/2000 Startup Screen Logo.

Follow the on-screen directions.

Turning off the power

The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode.

Shut Down mode (Boot mode)

When you turn off the power in Shut Down mode, no data is saved and the computer will boot to the operating system’s main screen.

1. If you have entered data, save it to the hard disk or to a diskette.

2. Make sure all disk activity has stopped, then remove any CDs or diskette.

CAUTION: Make sure the Disk is off. If you turn off the power while a

GETTING STARTED

disk is being accessed, you can lose data or damage the disk.

3. If you are using Windows XP, click start then click Turn off computer . From the Turn off computer menu select Turn off .

If you are using Windows 2000, click Start and click Shut Down. From the Shut Down menu select Shut Down.

4. Turn off the power to any peripheral devices.

CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

3-8

Turning off the power

Hibernation mode

The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The hibernation feature does not save the status of peripheral devices.

CAUTIONS: 1. While entering hibernation mode, the computer saves

the contents of memory to the HDD. Data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed. Wait for the Disk indicator to go out.

2. Do not install or remove a memory module while the computer is in hibernation mode. Data will be lost.

Benefits of hibernation

The hibernation feature provides the following benefits: ❑ Saves data to the hard disk when the computer automatically shuts down

because of a low battery.

NOTE: For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby will be lost.

❑ You can return to your previous working environment immediately when you

turn on the computer.

❑ Saves power by shutting down the system when the computer receives no

input or hardware access for the duration set by the System hibernate feature.

❑ You can use the panel power off feature.

ETTING

TARTED

3-9

User's Manual

Starting Hibernation

To enter Hibernation mode, follow the steps below.

Windows XP

1. Click Start .

2. Select Turn Off Computer.

3. Open the Turn Off Computer dialog box. Hibernate is not displayed.

4. Press the Shift key. The Standby item will change to Hibernate.

5. Select Hibernate.

Windows 2000

1. Click Start and click Shut Down.

2. In Shut Down Windows select Hibernate and click the OK button.

The computer will also enter Hibernate mode automatically when you:

❑ Press the power button. ❑ Close the lid.

GETTING STARTED

First, however, make the appropriate settings according to the steps below.

Windows XP/2000

1. In Windows XP, open the Control Panel, click Performance and Maintenance and click the TOSHIBA Power Saver icon.

In Windows 2000, open the Control Panel and double-click the TOSHIBA Power Saver icon.

2. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button.

3. Select the Power Save Modes window.

4. Double-click Power Save Mode and open the System Power Mode window.

5. Enable the desired Hibernation settings for When I press the power button and When I close the lid.

6. Click the OK button.

3-10

Turning off the power

Data save in hibernation mode

When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Disk indicator will light.

After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices.

CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

Standby mode

In standby mode the power remains on, but the CPU and all other devices are in sleep mode.

Standby precautions

❑ Before entering Standby mode, be sure to save your data. ❑ Do not install or remove a memory module while the computer is in standby

mode. The computer or the module could be damaged.

❑ Observe the following precautions regarding standby mode:

• Do not remove the memory module.

• Do not remove the Battery Pack.

Either action could cause the computer to hang up the next time you turn it on.

The computer could also hang up at power on if it shut down automatically in standby mode because of a low battery.

In any of the above cases, the standby configuration will not be saved.

ETTING

TARTED

The following message appears when you turn on the power:

WARNING: RESUME FAILURE. PRESS ANY KEY TO CONTINUE.

If the computer hangs up when you turn it on, perform the following: Press the power button and hold it down for five seconds, then turn the

power on again.

3-11

User's Manual

❑ If you carry the computer on board an aircraft or into a hospital, be sure to shut

down the computer in hibernation mode or in shutdown mode to avoid radio signal interference.

Benefits of standby

The standby feature provides the following benefits: ❑ Restores the previous working environment more rapidly than does hiberna-

tion.

❑ Saves power by shutting down the system when the computer receives no

input or hardware access for the duration set by the System Standby feature.

❑ You can use the panel power off feature.

Executing standby

You can enter standby mode in one of three ways:

1. In Windows XP, click Start, click Turn Off Computer and click Stand by. In Windows 2000, click Start, click Shut Down, select Stand by and click

OK.

2. Close the display panel. This feature must be enabled. Refer to the System

GETTING STARTED

Power Mode item in Power Saver Utility described in the Control Panel. In Windows XP, click Performance and Maintenance and click the

TOSHIBA Power Saver icon. In Windows 2000, double-click the TOSHIBA Power Saver icon.

3. Press the power button. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility described in the Control Panel.

In Windows XP, click Performance and Maintenance and click the TOSHIBA Power Saver icon.

In Windows 2000, double-click the TOSHIBA Power Saver icon.

When you turn the power back on, you can continue where you left when you shut down the computer.

NOTES: 1. When the computer is shut down in standby mode, the

power indicator glows orange.

2. If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Standby mode consumes more power.

3-12

Restarting the computer

Standby limitations

Standby will not function under the following conditions:

❑ Power is turned back on immediately after shutting down. ❑ Memory circuits are exposed to static electricity or electrical noise.

Restarting the computer

Certain conditions require that you restart the computer system. For example, if:

❑ You change certain computer settings. ❑ An error occurs and the computer does not respond to your keyboard

commands.

There are two ways to restart the computer system:

1. If you are using Windows XP, click start then click Turn off computer. From the Turn off computer menu select Restart.

If you are using Windows 2000, click Start and click Shut Down. From the Shut Down menu select Restart.

2. Press the power button and hold it down for five seconds. Wait 10 to 15 seconds, then turn the power on again by pressing the power button.

ETTING

TARTED

3-13

User's Manual

Restoring the preinstalled software from the Product Recovery CD-ROM

If preinstalled files are damaged, use the Product Recovery CD-ROM to restore them. To restore the operating system and all preinstalled software, follow the steps below.

CAUTION: When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

1. Load the Product Recovery CD-ROM in the optional optical disk drive and turn off the computer’s power.

2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key.

3. Use the left or right cursor key to select the CD-ROM icon in the display menu. For details, refer to the Boot priority section in Chapter 7, HW Setup.

4. Follow the on-screen instructions.

GETTING STARTED

3-14

Chapter 4

Operating Basics