To keep your sWaP Classic BX1-S watch in good operating condition
Watch Phone
6
please read this manual carefully before using it.
The sWaP Classic BX1-S watch is a combination of intricate design,
delicate craftsmanship, comfortable to wear, a convenient handwriting
recognition function and touch keypad, colorful touch screen, ring tones, file
management, camera and video function, voice record function, MP3/MP4
players, supports MMS, WAP.
1.2 Safety notice
★ If your phone is lost or stolen, please notify your network provider to
initiate the cancellation of the sim card. You make be asked for the IMEI
number. This should be written down and stored in a safe place. To find
your IMEI number, please check the battery compartment or the box which
the sWaP Classic BX1-S phone was issued in.
★To avoid misuse of your phone, please enable the safety measures,
Such as:
Setting SIM card and PIN No.
Setting phone PIN
1.3Safety alert and notice
★ Please do not use your sWaP Classic BX1-S watch when you are
driving, in extreme circumstances, use hand free accessories to accept
calls. Please remember, it is illegal in some countries to make/receive calls
when driving.
★All mobile devices may cause interference to radio devices, using
sWaP Classic BX1-S mobile on plane is illegal and dangerous, please
make sure keep your phone power off during flight.
★ Power OFF within dangerous areas such as:
At Petrol and Gas stations, oil digging plants, chemical plant or explosion
areas, you must abide by relevant law or rules, and power off your phone.
Watch Phone
sWaP Classic BX1-S
7
sWaP Classic BX1-S
professionals;
★Abide by special regulations
Abide by special regulations, and keep your phone powered off at places
which may cause interference or danger to other equipment (such as in
hospitals)
★Interference
Any phone may have talk quality interference by other radio waves.
★ Servicing Your Phone.
The mobile phone watch must be installed and maintained by
unauthorized installing and repairing may cause danger, and will lead to
invalidation of the warranty.
★ Fittings and battery
Only use the fittings and battery approved by sWaP Classic BX1-S.
★ Use properly
★ Emergency call
Make sure your phone is powered on and in service, input emergency call
NO, (such as 999 and others), dial to call, tell your position and make a
brief of status, and please do not terminate conversation without
permission.
★Note: As any other mobiles, for the reason of network or signal
transfer status may not support all the functions of this mobile. Certain
networks may even not support 112 emergency calls. So you can not
depend on your sWaP Classic BX1-S mobile totally. When there is
important communication, (such as medical first aid).
★ Please contact local network supplier for information and check.
1.4 Battery Charging.
(1) You need to completely charge the battery before use. For a new
product, it’s better that charge the battery for up to 10 hours. This is so the
battery can achieve full performance.
(2) When you charge the battery, the sWaP Classic BX1-S watch will feel
warm, but it is installed temperature protection will control the change of
temperature and the charge, usually you need charge for 4 hours.
Watch Phone
8
(3) When the battery meter is low, the screen will show “Battery low”. This is
to remind for charge the sWaP Classic BX1-S watch.
Notice: The battery’s functions (such as standby time and talk time) are
different when working due to operation and network system.
1.5 Usage notice
Your mobile watch is of delicate craftsmanship, it should be protected
carefully. The following suggestions will help your machine serve you well
for many years.
⑴ Don’t touch screen with sharp objects and keep screen clean. Never
use the product when it is damaged. It is normal if the screen startup slowly
under low temperature.
⑵ Keep your mobile watch other parts and fittings beyond the reach of
children and animals.
(3) Please note: you must avoid water splashes/drops onto the mobile
watch or on its body, if this happens, it will not work, and this is not covered
in the standard warranty policy.
Keep the product dry, keep away from rain, moisture and liquid which may
contain corrosive matters, if the mobile is wet, please take out battery
immediately and only reinstall battery after it has complete dried.
(4) Do not use or store the product in dusty places in order to avoid its parts
be damaged.
⑸ Do not put the product in places of heat. High temperature will shorten
the life of electronic circuit board.
(6) Do not put the product at cold places, otherwise the mobile will have
humidity damage and ruin the electronic circuit board.
(7) Do not throw, beat or vibrate your mobile which will damage the
electronic circuit board and structure.
(8) Do not use corrosive chemical product, cleanser or scour to clean the
watch mobile. Please use a soft towel to clean.
Watch Phone
sWaP Classic BX1-S
9
(9) If your product or accessories do not work, please send to professional
service station, Professionals there will provide maintain service for you.
Ⅱ、 Introduction to your watch mobile
1>picture induction
1:touch screen 2:watchcase 3:band 4:cameraslot
5:powerkey 6:menu & ok key 7:USB jack
2> key pad
Power key: Press this key to turn on or turn off the mobile watch, Return to
the standby mode by pressing this key under the turning-on status.
Confirmation key: perform the words at down left on scream bottom line.
3> Install SIM Card (insert/take out SIM card)
(1) Attention: The sWaP Classic BX1-S watch must be powered off when
you insert or remove the SIM card / Micro SD card.
(2) Remove the battery.
The SIM card should be inserted carefully making sure the contact area face
down and the nicked face inside. Turn on the sWaP Classic BX1-S. The sWaP
Classic BX1-S will auto search network and go to standby status.
10
Watch Phone
sWaP Classic BX1-S
If you would like to change to another SIM card, you should confirm mobile
shut down, and follow the procedure to remove the SIM Card,
Failure to follow the procedure correctly will result in damage to your SIM
card and possibly your sWaP Classic BX1-S Watch.
(3) SIM cards have your information, including your mobile number, PIN,
PIN2, PUK (PIN unlock key), PUK2 (PIN2 unlock key) and IMSI Code and
network info, phonebook and messages.
Please Note:
☆ The sWaP Classic BX1-S mobile will support 3V SIM card.
☆
☆ Please keep your mobile and SIM card beyond the reach of Children.
Install steps :Press On-off Key for a few seconds to power off, then put SIM
card face downwards into SIM card seat and push SIM card in carefully.
(4)Insert Micro SD card
You can insert or remove the Micro SD card by sliding the silver slot forward
and when you want to lock the Micro SD card slot, back.
(5) Attach battery and power on.
4>Screen
Screen includes three parts.
(1) A:Standby menu: you can choice various pictures to show time and
date. (can set accord to your requirement)
B:Shut down setting:you can choice various pictures to show end (can set accord
to your requirement)
11
Watch Phone
sWaP Classic BX1-S
sWaP Classic BX1-S
(2)Icons on top indicate the signal status and battery volume, etc.
GPRS function
MMS
Signal Level
Earphone
Lock key is open
Lock key is close
Bluetooth
Alarm
Common mode
Missed call
SMS or MMS full
Battery Meter
(3) Middle area indicates messages, indication and other input content, including
numbers, words and dynamic icons.
(4) Bottom area has two divisions: two icons and four function icons.
Menu、message dial mp3 player camera 、
12
Watch Phone
Phonebook
5> Dial call
Touch icon with touch pen at standby status, this will then bring an
on-screen keyboard. Use the stylus to press the numbers required, then press
confirm key to dial call, press On-off key or press Cancel on the screen to end
call.
(1)To view phone book by press icon in menu under the standby status,
finding the number you want, then press “ IP dial” in “Option”, the phone
could dial the correspond number automatically.
Re-dial number
(2)To display call records by press icon in the menu under the standby
status, please choose number from call number display, then dial the number.
(3) Speed Dial.
To setup Speed Dial go into:
-Settings
-Phone setup
-Speed dial.
You now have the option to choose
1. Enable speed Dial
2. Set Number.
If you enable speed dial, this will allow you to use the on screen numeric keypad
to speed dial.
Watch Phone
sWaP Classic BX1-S
13
Set Number allows you to edit position 2-9 for your speed dial numbers.
To assign the speed dials simply go to:
Set Number
Choose the field i.e. 2-9,
Then click on the field.
Choose EDIT
And scroll through your phone book list until you find the number/name you
require.
Click on the name/number and the process is complete.
Press under the standby status to show digital simulate keypad, press any
No. from 2~9, and dial the quick Number.
6> Answer phone
Press “confirmation key” to answer.
Press “On-off key” to stop a call.
Press “On-off key” to refuse a call.
Press “Option” to “Pause, stop, new call, phone book, message, voice record,
mute/restore, double music multi frequency and so on.
7> Input switch
This mobile support hand write, spell, number, English, capital English input, and
could be used in editing phonebook, message, memo, file management, greetings
and other file editing.
(1) Input icon
After enter into editing windows (include editing phonebook, message, and
memo), the icons are following: