MICRO INVERTER DXM300
USER MANUAL
System Function
◆ Power line carrier-current communication(this is optional function,please confirm the spec outside the box first .)
: . : :
:
. :
◆ 6-grade power search---
◆ Wide voltage input(22-50VDC)---
◆ High-frequency two-way and one-way grid function---
◆ Kinds of frequency output function---
◆Directly connected to the solar panels (do not need to connect the battery)
◆ AC 0 angle with high precision auto-detection---
◆ Synchronous High- frequency M
odulation
◆ Pure Sine Wave Output---
◆ Power Automatically Locked (APL)---
◆ Constant Current, Constant Power---
◆ Exactly and timely automatic Island Effect Protection
◆ High-Frequency High Conversion Rate---
.
◆ Maximum Power Point Tracking (MPPT)---
◆ Stack using---
◆ DC input---
◆ AC output---
By using electric power as a carrier of AC alternating current, can modulate high-frequency and carrier frequency (60KHz) in AC
wire transmission and can achiev
e the communication/ newsletter between inverters or between inverter and computer. And it
can transfer the power data . Also monitor all functions of inverter.
1.Carrier frequency 60KHZ(Frequency customizable); 2 Interface way TTL level serial interface; 3.Carrier rate 300BPS;
4.Serial rate 9600PS(Can customize according to customer's request);
5 Modulation mode FSK+DSSS; 6.Newsletter distance:400m;
In overcast weather, the PV Panel’s output current is extreme
ly tiny, then inverter will automatic
open 6-grade power search function,and keep outputing efficent and steady during the low power .
1.DC voltage input:22~50VDC; 2.Second level power variable voltage conversion.
1.High frequency direct modulation, AC half wave synthesis;
2.Two-way grid means: Load consume directly. And can reverse AC current transmission.
1.It can apply to 50Hz and 60Hz frequency of AC; 2.Frequency range: 45Hz ~ 64Hz;
High-precision analysing the AC
phase angle .The phase shift rate is less
than 1%, thus achieve high-precision with phase modulation AC output together.
1.AC phase shift: < 1%; 2.Over-zero protection: 0.2 VAC; 3.AC switching: 50Hz / 60Hz.
1.Modulation synthesis: half wave and full-bridge modulation synthesis (100Hz / 120Hz) ;
2.Synthetic way: MOSFET full-bridge; 3.High frequency: 50KHz.
Use SPWM directly to make pure sine wave output.
1.Output waveform: Adopt complementary PWM to push-pull pure sine wav
e; 2.Generate means: enhancement-mode SPWM.
automatically powers locked in maximum power point, made output more stable.
constant current and output power, without any overload, over-current phenomenon.
Adapt high frequency converter, the output more efficient
high-precision (MPPT) operation power, automatic and immediate adjust the solar
panels output power at the maximum output point,made the inverter discharge to power grid with the highest efficiency.
S
uch as: 4 micro inverter of 260W stacking can achieve 1040W. the number of the stacking is unlimited.
Input voltage range: 22V to 50V,PV Panel: Recommend using the power more than 30W and the standard voltage
of 36V PV panels.Suggestion making the PV in parallel.
220VAC: 180V - 262V, 50HZ; 110V AC: 80V - 160V, 60HZ.
Notes:
Accessories for product:
LED Display
★Please connect the inverter following the operation instruction show above. If have any question please contact
with relative persons.
Non-professionals do not disassemble.Only qualified personnel may repair this product.
Please install inverter in the low humidity and well-ventilated place to avoid the inverter over-heating,and clear
around the inflammable and explosive materials.
When using this product, avoid children touching,playing, to avoid electric shock.
Connected solar panels, battery or wind generators
DC input DC power supply cable.
1.One warranty card;
2.One user manual;
3.One certificate of quality;
4.1 pouch of screw for micro inverter in tallation;
5.One AC Cable;
★
★
★
★
s
1.Red light 3 second---Red LED light 3 second while device starts , then in working condition;
2.Green flash fast---MPPT searching;
3.Green flash slow---MPPT + searching;
4. Red flash slow---MPPT - searching;
5.Green lights on 3s and off 0.5s---MPPT locked;
6.Red light steady---a. Islandi
ng protection;b.Over-temperature protection;c.Over / low AC voltage protection;
d. Over / low DC voltage protection; e.Fault
Remarks:
LED flashing in the process of being working condition:inverters connected to AC & DC sides→Red LED light 3
second→Green LED flash fast(MPPT searching)→Green LED flash slow(MPPT + searching) / Red LED flash slow
(MPPT - searching) / reen LED lights on 3s and off 0.5s (MPPT locked) .