DX Engineering DXE-UT-80P Instructions manual

PL-259 Connector Installation Tool

DXE-UT-80P

US Patent No. 8,701,278 and 9,614,341

DXE-UT-80P-INS Rev 2c

This patented assembly tool allows simple threading of the PL-259 sleeve onto the vinyl jacket of DXE-8U, DXE-11U, DXE-213U, DXE400MAX,
RG-8/U, RG-11U, RG-213/U, LMR-400 and other similar size cables. First properly strip the coaxial cable with the DXE-UT-8213 Cable Stripping
Tool. Place the collar on the cable and slide it out of the way. Place the threaded sleeve of the PL-259 connector over the end of the coaxial cable.
Start the coaxial cable end into the body of the connector and make sure all the strands of the center conductor of the cable are inserted into the center
pin. Then, use this simple hand-gripped tool - forget about those pliers that scarred the connector and ripped off chunks of metal - and thread the
connector body onto the stripped cable end. Tighten the tool until the PL-259 is fully seated on the coaxial cable. A visual guide at the end allows
easy viewing of the cable center conductor for proper depth of installation. When the PL-259 is fully on the coaxial cable, remove it from the
assembly. This tool allows a perfect and easy connector installation every time!

Properly prepare coaxial cable Insert coaxial cable into PL-259 Use PL-259 Connector Installation Tool

Verify strands are fully into center pin Remove tool and you're ready to solder

DX Engineering 2017

1200 Southeast Ave. - Tallmadge, OH 44278 USA

Phone: [phone] ∙ Tech Support and International: [phone]

Fax: [phone] ∙ E-mail: [e-mail]

Technical Support

If you have questions about this product, or if you experience difficulties during the installation, contact DX Engineering at [phone]. You can
also e-mail us at:

[e-mail]

For best service, please take a few minutes to review this instruction sheet before you call.

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from date of shipment.
DX Engineering’s sole obligation under these warranties shall be to issue credit, repair or replace any item or part thereof which is proved to be other than as warranted;
no allowance shall be made for any labor charges of Buyer for replacement of parts, adjustment or repairs, or any other work, unless such charges are authorized in
advance by DX Engineering. If DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering shall, upon prompt notice thereof,
issue shipping instructions for return to DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to
be waived by Buyer unless made in writing. The above warranties shall not extend to any products or parts thereof which have been subjected to any misuse or neglect,
damaged by accident, rendered defective by reason of improper installation, damaged from severe weather including floods, or abnormal environmental conditions such
as prolonged exposure to corrosives or power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any goods or parts
thereof furnished by Buyer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties do not extend to other equipment and parts
manufactured by others except to the extent of the original manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties are limited to
the precise terms thereof. These warranties provide exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential damages.
SELLER NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION
OR LIABILITY NOT STRICTLY IN ACCORDANCE WITH THE FOREGOING.

©DX Engineering 2017

DX Engineering®, DXE®, DX Engineering, Inc.®, Hot Rodz®, Maxi-Core®, DX Engineering THUNDERBOLT®, DX Engineering Yagi Mechanical®, EZ-BUILD®,
TELREX®, Gorilla Grip® Stainless Steel Boom Clamps, Butternut®, SkyHawk™, SkyLark™, SecureMount™, OMNI-TILT™, RF-PRO-1B®, AFHD-4® are trademarks
of PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and product names are the
trademarks of their respective owners.

Specifications subject to change without notice.



-