Genius Clamp Bolt Selection Chart Rev 0
Bolt Length Selection Chart
Outside Diameter
1.00”
1.25”
1.50”
1.75”
2.00”
1.00 inch
4.0”
4.0”
4.5”
5.0”
5.0”
1.25 inch
4.0”
4.5”
5.0”
5.0”
5.5”
1.50 inch
4.5”
5.0”
5.0”
5.5”
5.5”
1.75 inch
5.0”
5.0”
5.5”
5.5”
6.0”
2.00 inch
5.0”
5.5”
5.5”
6.0”
6.5”
Part Number
Description
DXE-SSGC-2P
Genius Clamps, Stainless Steel, 1 to 2 inch OD, Pair
Part Number
Bolt Set Description
DXE-SSGC-Bolt-4
4.0 inch length Bolt and Hardware, 5/16-18 Stainless Steel, for Genius Clamp, set of 8
DXE-SSGC-Bolt-4-5
4.5 inch length Bolt and Hardware, 5/16-18 Stainless Steel, for Genius Clamp, set of 8
DXE-SSGC-Bolt-5
5.0 inch length Bolt and Hardware, 5/16-18 Stainless Steel, for Genius Clamp, set of 8
DXE-SSGC-Bolt-5-5
5.5 inch length Bolt and Hardware, 5/16-18 Stainless Steel, for Genius Clamp, set of 8
DXE-SSGC-Bolt-6
6.0 inch length Bolt and Hardware, 5/16-18 Stainless Steel, for Genius Clamp, set of 8
DXE-SSGC-Bolt-6-5
6.5 inch length Rod and Hardware, 5/16-18 Stainless Steel, for Genius Clamp, set of 8
DX Engineering Genius Clamps are designed for mounting round tubing and pipe members perpendicular to each other. If you
want to build a tower standoff to side mount a dipole, vertical or Yagi on your tower, Genius Clamps are perfect for the job.
They're so versatile that their use is limited only by imagination. The stainless steel Genius Clamps fit on ROHN 25, 45 or 55G
tower sections, or equivalent and facilitate creating side arm and other mounts for your antenna systems. They are sold as a
pair so you will have a set for each tower leg. Genius Clamps are not designed for parallel tube or pipe mounting applications,
only perpendicular.
Because their construction is high-quality 1/8- in. thick 304 stainless steel, Genius Clamps can last beyond the life of a steel
tower. These clamps can handle any size tubing or tower leg from 1.0 in. to 2.0 in. diameter, in both directions, 90
degrees from each other. Each clamp consists of three pieces; two identical single-direction flanged outer saddles and one unique inner saddle with dualdirection "side saddle" flanges. Match them with our DX Engineering SSGC-BOLT Series of stainless steel bolts and hardware for the ultimate in pipe or
tubing and tower fastening.
These clamps are sold in pairs for securely attaching one side mount cross arm tube to two tower legs, for example, which could be used to hang a wire
antenna. A different installation example pictured here shows a tower with a side-mounted vertical antenna, which demonstrates the use of three pairs of
Genius Clamps. The two pieces of tubing and the bolt set of the appropriate length that is required for the project are sold separately.
© DX Engineering 2015 - 1200 Southeast Ave. - Tallmadge, OH 44278 USA - Phone: (800) 777-0703 ∙ Tech Support and International: (330) 572-3200 - Fax: (330) 572-3279 ∙ E-mail: DXEngineering@DXEngineering.com
Loading...