DX Engineering DXE-RADW-40MK Instructions manual

PRE-CUT RADIAL WIRE KITS

DXE-RADW-1K/40MK/80MK

Pre-Cut Radials for

10, 15, 20, 40, 80 Meter

Elevated Vertical Antennas

DXE-RADW-K-MK-INS Rev 1b

DXE-RADW-1K - Twelve (12) Pre-Cut Radial Wires. Four (4) each for: 10 Meters, 15 Meters and 20 Meters. 12 each 1/4" ring terminals.
Lengths for the bands are: 10 Meters = 8 feet, 9 inches. 15 Meters = 11 feet, 9 inches. 20 Meters = 17 feet, 6 inches.

DXE-RADW-40MK - Four (4) Pre-Cut Radial Wires - 35 feet each and includes 4 each 1/4" ring terminals.
DXE-RADW-80MK - Four (4) Pre-Cut Radial Wires - 70 feet 3 inches each and includes 4 each 1/4" ring terminals.

The DXE-RADW-K Pre-Cut Radial Wire Kits include the highest quality 14 AWG copper stranded copper wire with a relaxed black PVC insulation for
easy installation of your radial system. Also included are 1/4" ring terminals. These Pre-Cut Radial Wire Kits are specifically designed for users of Elevated
Vertical Antenna Systems which have the need of a high quality radial system for optimum performance.

Strip one end of the pre-cut radial wire approximately 1/4" and crimp one 1/4" ring terminal in place on the exposed wire. You may solder the terminals if
desired. When laying out the elevated radial wires, space them evenly around the antenna base. The optional laser cut stainless steel DXE-RADP-3 Radial
Plate, may be used to hold them in place using the optional DXE-RADP-1HWK Hardware Kit which contains all stainless steel 1/4" bolts, nuts, flat
washers, split washers, and star washers. Do not zig-zag, bunch or cross over other radial wires. Space them out evenly around the antenna base. Care should
be taken when using elevated radials so they will not interfere with objects, animals or people that may come into contact with them. As with any antenna
system, stay away from power lines, power sources, other antennas or metallic objects. Note: JTL-12555 Jet-Lube SS-30 Anti-Seize should be used on all
clamps, bolts and stainless steel threaded hardware to prevent galling and to ensure proper tightening.

Note: These pre-cut radial kits are custom made for elevated vertical antenna installations. For ground mounted vertical antenna installations refer to the
DXE-RADW-RT Radial Wire kits, Bulk Radial kits and quality supplies available from DX Engineering.

Optional DXE-RADP-1HWK Radial Plate Hardware

Radials symmetrically placed around the optional DXE-RADP-3 Radial Plate

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1200 Southeast Ave, Tallmadge, OH 44278 USA

Phone: [phone] ∙Tech Support and International: [phone]

Fax: [phone] ∙ E-mail: [e-mail]

Technical Support

If you have questions about this product, or if you experience difficulties during the installation, contact DX Engineering at [phone]. You can also e-mail us at:

[e-mail]

For best service, please take a few minutes to review this instruction sheet before you call.

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from date of shipment. DX Engineering’s sole obligation
under these warranties shall be to issue credit, repair or replace any item or part thereof which is proved to be other than as warranted; no allowance shall be made for any labor charges of Buyer for
replacement of parts, adjustment or repairs, or any other work, unless such charges are authorized in advance by DX Engineering. If DX Engineering’s products are claimed to be defective in material
or workmanship, DX Engineering shall, upon prompt notice thereof, issue shipping instructions for return to DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach
of these warranties shall be deemed to be waived by Buyer unless made in writing. The above warranties shall not extend to any products or parts thereof which have been subjected to any misuse or
neglect, damaged by accident, rendered defective by reason of improper installation, damaged from severe weather including floods, or abnormal environmental conditions such as prolonged exposure
to corrosives or power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any goods or parts thereof furnished by Buyer or acquired from others at Buyer’s

specifications. In addition, DX Engineering’s warranties do not extend to other equipment and parts manufactured by others ex cept to the extent of the original manufacturer’s warranty to DX

Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof. These warranties provide exclusive remedies, expressly in lieu of all other remedies including
claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY
NOT STRICTLY IN ACCORDANCE WITH THE FOREGOING.
©DX Engineering 2021
DX Engineering®, DXE®, Hot Rodz™, Maxi-Core™, THUNDERBOLT™, Antenna Designer™, Yagi Mechanical™, and Gorilla Grip® Stainless Steel Boom Clamps, are trademarks of PDS
Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and product names are the trademarks of their respective owners.
Specifications subject to change without notice. Date Printed: 3/2/2021 11:41 AM