DX Engineering DXE-RADW-32RT Instructions Rev

RADIAL WIRE KITS

DXE-RADW-20RT/32RT/65RT/120RT

20 Feet / 32 Feet / 65 Feet / 120 Feet

DXE-RADW-RT-INS Rev 2

DXE-RADW-20RT - 20 Pre-Cut Radial Wires, each 20 Ft long with one 1/4" Ring Terminal professionally crimped and soldered.
DXE-RADW-32RT - 20 Pre-Cut Radial Wires, each 32 Ft long with one 1/4" Ring Terminal professionally crimped and soldered.
DXE-RADW-65RT - 20 Pre-Cut Radial Wires, each 65 Ft long with one 1/4" Ring Terminal professionally crimped and soldered.
DXE-RADW-120RT - 10 Pre-Cut Radial Wires, each 120 Ft long with one 1/4" Ring Terminal professionally crimped and soldered.

The DXE-RADW-Radial Wire Kits include the highest quality 14 gage copper stranded wire with a relaxed black PVC insulation for easy installation of your radial
system. The pre-cut radial wires include 1/4" Ring Terminals professionally crimped and soldered on one end. These Radial Wire Kits are designed for users of
Vertical Antenna Systems which have the need of a high quality radial system for optimum performance. Note: JTL-12555 Jet-Lube SS-30, PTX-81343 Never-Seez
or DXE-NSBT8 Anti-Seize should be used on all clamps, bolts and stainless steel threaded hardware to prevent galling and to ensure proper tightening.

When laying out the radial wires, space them evenly around the optional DXE-RADP-3 Radial Plate, holding them in place using the DXE-RADP-1HWK Hardware Kit
containing all stainless steel 1/4" bolts, nuts, flat washers, split washers, and star washers. If your available space does not allow the complete length radial wire
supplied, cut the radial as required. Do not zig-zag, or cross over other radial wires. You may solder the terminals if desired. No need to bury your radials! - Use
the DXE-STPL-100P Radial Steel Wire Anchor Pins (also called Lawn Staples) which are perfect for fastening radials below the grass line to eliminate the risk of
damaging your radials during lawn maintenance. DX Engineering also offers the ecologically friendly DXE-STPL-100BD Biodegradable staples which will disappear
in about a year - after the grass root system has captured the radial wires. Please visit the DX Engineering web site at www.dxengineering.com and read our Tech
Article on, How to Install Disappearing Radial Wires without Digging for further information on utilizing our Radial Wire Anchor Pins.

Optional DXE-RADP-1HWK Radial Plate Hardware

Optional DXE-STPL-100P
Steel Radial Wire Anchor Pins Radials symmetrically placed
around the optional DXE-RADP-3

Radials shown as red for illustration purposes
Optional DXE-STPL-100BD
Biodegradable Lawn Staples Radials shown cut to fit in the available space

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Technical Support

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from date of shipment. DX Engineering’s sole obligation under these
warranties shall be to issue credit, repair or replace any item or part thereof which is proved to be other than as warranted; no allowance shall be made for any labor charges of Buyer for replacement of parts,
adjustment or repairs, or any other work, unless such charges are authorized in advance by DX Engineering. If DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering
shall, upon prompt notice thereof, issue shipping instructions for return to DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived
by Buyer unless made in writing. The above warranties shall not extend to any products or parts thereof which have been subjected to any misuse or neglect, damaged by accident, rendered defective by reason of
improper installation, damaged from severe weather including floods, or abnormal environmental conditions such as prolonged exposure to corrosives or power surges, or by the performance of repairs or
alterations outside of our plant, and shall not apply to any goods or parts thereof furnished by Buyer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties do not extend to other
equipment and parts manufactured by others except to the extent of the original manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof.
These warranties provide exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY
WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX
ENGINEERING ANY OBLIGATION OR LIABILITY NOT STRICTLY IN ACCORDANCE WITH THE FOREGOING.
©DX Engineering 2016 Specifications subject to change without notice.
DX Engineering®, DXE®, DX Engineering, Inc. ®, Hot Rodz®, Maxi-Core®, DX Engineering THUNDERBOLT®, DX Engineering Yagi Mechanical®, EZ-BUILD®, TELREX®, Gorilla Grip® Stainless Steel Boom Clamps,
Butternut®, SkyHawk™, SkyLark™, SecureMount™, OMNI-TILT™ are trademarks of PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other
brands and product names are the trademarks of their respective owners.

If you have questions about this product, or if you experience difficulties during the installation, contact DX Engineering at [phone]. You can also e-mail us at:

For best service, please take a few minutes to review this instruction sheet before you call.

1200 Southeast Ave ∙ Tallmadge, OH 44278 USA

Phone: [phone] ∙Tech Support and International: [phone]

Fax: [phone] ∙ E-mail: [e-mail]

[e-mail]