DX Engineering DXE-NL-PRE-ATT-1 Instructions manual

Portable Receive

Preamplifier-Attenuator

DXE-NL-PRE-ATT-1

The DXE-NL-PRE-ATT-1, DX Engineering Portable Receive Preamplifier-Attenuator,
is a very handy device to use with your receiver; handheld, portable or base. This
attractive, light-weight unit comes completely assembled and tested, and provides a nominal 30

dB gain across the frequency range from 100 kHz through
30 MHz. Powered by an internal 9 volt battery (not
included), it features BNC connectors for RF Input and

Output, easy to use slide switches and a ‘power on’ LED

when the preamp is on. Attenuation is selected with
switches for -10 dB or -20 dB and -30 dB with both. Plus,
an AM Broadcast Band Rejection Filter can be switched in
or out, as needed. This unit is 3.25 x 7.00 x 1.00 in. and
weighs approx. 8-1/2 oz. with battery installed.

This Portable Preamplifier Attenuator unit is a perfect
companion for use with the DXE-NOISELOOP WD8DSB
Portable Receive Flag Antenna Kit, for RFI noise finding
and for MW through SW receiving. You can use Velcro
(not included) to mount the DXE-NL-PRE-ATT-1 on the
handle of the DXE-NOISELOOP, or onto your own project.

NOTE: The DXE-NL-PRE-ATT-1 Receive Preamplifier­Attenuator is a Receive Only device. Attempting to
transmit RF into this unit will cause damage that is not
covered by warranty.

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year
from date of shipment. DX Engineering’s sole obligation under these warranties shall be to issue credit, repair or replace any item or part
thereof which is proved to be other than as warranted; no allowance shall be made for any labor charges of Buyer for replacement of parts,
adjustment or repairs, or any other work, unless such charges are authorized in advance by DX Engineering. If DX Engineering’s products are
claimed to be defective in material or workmanship, DX Engineering shall, upon prompt notice thereof, issue shipping instructions for return to
DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by
Buyer unless made in writing. The above warranties shall not extend to any products or parts thereof which have been subjected to any
misuse or neglect, damaged by accident, rendered defective by reason of improper installation, damaged from severe weather including
floods, or abnormal environmental conditions such as prolonged exposure to corrosives or power surges, or by the performance of repairs or
alterations outside of our plant, and shall not apply to any goods or parts thereof furnished by Buyer or acquired from others at Buyer’s

specifications. In addition, DX Engineering’s warranties do not extend to other equipment and parts manufactured by others except to the

extent of the original manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof. These warranties provide exclusive remedies, expressly in lieu of all other remedies

including claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT STRICTLY IN ACCORDANCE WITH THE FOREGOING.

©DX Engineering 2021

DX Engineering®, DXE®, DX Engineering, Inc.

®,

, Hot Rodz®,, Maxi-Core®,, DX Engineering THUNDERBOLT®,, DX Engineering Yagi Mechanical®,, EZ-BUILD®,, TELREX®,, Gorilla Grip®, Stainless Steel Boom Clamps, Butternut®,,
SkyHawk™, SkyLark™, SecureMount™, OMNI-TILT™, RF-PRO-1B®, AFHD-4®, are trademarks of PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and
product names are the trademarks of their respective owners.. Specifications subject to change without notice.

Technical Support

If you have questions about DX Engineering products, or if you experience difficulties during the installation, contact DX Engineering at [phone]. You can also e-mail us at: [e-mail]

Information and Instruction Sheet Updates

Every effort is made to supply the latest information or instruction sheet revision with each product. Occasionally an information or instruction sheet will be updated between the time your DX Engineering product is shipped and when you
receive it. Please check the DX Engineering web site (www.dxengineering.com) for the latest revision information or instruction sheet.

© DX Engineering 2021

DX Engineering - 1200 Southeast Ave. - Tallmadge, OH 44278 USA

Phone: [phone] - Tech Support and International: [phone] - Fax: [phone]

E-Mail: [e-mail]

DXE-NL-PRE-ATT-1-INS Rev 0