DX Engineering DXE-LLSP-RP Instructions manual

Ladder Line Surge Protector

Repair Parts Kit

DXE-LLSP-RP

DXE-LLSP-RP-INS Rev 1

Lightning or surges can do havoc - even if the surge is not near your location, damage can happen. This kit of
parts will provide you with the needed components to repair your DXE-LLSP Ladder Line Surge Protector. Included in
this kit is a new printed circuit board (PCB), two resistors, two capacitors and two gas discharge tubes. Assembly is
straight forward using a standard soldering iron and good quality solder. There are no polarity requirements for the parts.
Install the capacitors in C1 and C2. Install the resistors in R1 and R2. Install the gas discharge tubes in GDT1 and GDT2.
Once the components are installed, you can reuse the hardware from your DXE-LLSP to install the replacement PCB in
place.












Parts Kit Parts Assembled PCB Mounted inside DXE-LLSP




Phone: [phone] ∙ Tech Support and International: [phone]

1200 Southeast Ave. - Tallmadge, OH 44278 USA

Fax: [phone] ∙ E-mail: [e-mail]

DX Engineering 2019

Technical Support

If you have questions about this product, or if you experience difficulties during the installation, contact DX Engineering at [phone]. You can
also e-mail us at:

[e-mail]

For best service, please take a few minutes to review this instruction sheet before you call.

Warranty

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from date of shipment. DX En gineering’s sole obligation under these warranties
shall be to issue credit, repair or replace any item or part thereof which is proved to be other than as warranted; no allowance shall be made for any labor charges of Buyer for replacement of parts, adjustment or repairs, or any
other work, unless such charges are authorized in advance by DX Engineering. If DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering shall, upon prompt notice thereof, issue
shipping instructions for return to DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by Buyer unless made in writing. The above
warranties shall not extend to any products or parts thereof which have been subjected to any misuse or neglect, damaged by accident, rendered defective by reason of improper installation, damaged from severe weather
including floods, or abnormal environmental conditions such as prolonged exposure to corrosives or power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any goods or parts

thereof furnished by Bu yer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties do not extend to other equipment and parts manufactured by others except to the extent of the original
manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof. These warranties provide exclusive remedies, expressly in lieu of all other remedies

including claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT STRICTLY IN ACCORDANCE
WITH THE FOREGOING.

©DX Engineering 2019

DX Engineering®, DXE®, DX Engineering, Inc.®, Hot Rodz®, Maxi-Core®, DX Engineering THUNDERBOLT®, DX Engineering Yagi Mechanical®, EZ-BUILD®,
TELREX®, Gorilla Grip® Stainless Steel Boom Clamps, Butternut®, SkyHawk™, SkyLark™, SecureMount™, OMNI-TILT™, RF-PRO-1B®, AFHD-4® are
trademarks of PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and product
names are the trademarks of their respective owners.

Specifications subject to change without notice.

