Dwyer Instruments Series DH3 Digihelic, Series DH3, DH3 DIGIHELIC Operating And Installation Instruction

Bulletin B-30

Series DH3 Digihelic®Differential Pressure Controller

Specifications - Installation and Operating Instructions

DWYER INSTRUMENTS, INC.

Phone: [phone] www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, IN 46360, U.S.A. Fax: [phone] e-mail: [e-mail]

1.800.868.7495

QualityInstruments-Direct.ca

2

SPECIFICATIONS
Service: Air and non-combustible, compat-

ible gases.

Wetted Materials: Consult factory.
Housing Material: Die cast aluminum

case and bezel.
Accuracy: ±1.5% for 0.25˝ and ±0.25˝ w.c.
ranges. Ranges 0.5˝ to 5˝ w.c. and corre­sponding bi-directional (except ±2.5˝ w.c.):
±1%; All other ranges: ±0.5% @ 77°F
(25°C) including hysteresis and repeatabili­ty (after 1 hour warm-up).

Stability: < ±1% per year.
Pressure Limits: Ranges

≤ 2.5˝ w.c.: 25 psi; ±2.5˝, 5˝ w.c.: 5 psi;
10˝: w.c. 5 psi; 25˝ w.c.: 5 psi; 50˝ w.c.: 5
psi; 100˝ w.c.: 9 psi.
Temperature Limits: 32 to 140°F (0 to
60°C).
Compensated Temperature Limits: 32 to
140°F (0 to 60°C).
Thermal Effects: 0.020%/°F (0.036/°C)
from 77°F (25°C). For 0.25˝ and ±0.25˝
w.c. ranges: ±0.03%/°F (±0.054%/°C).

Power Requirements: 12-24 VAC/VDC.
Power Consumption: 3 VA max.

Output Signal: 4-20 mA DC into 900

ohms max.
Zero & Span Adjustments: Accessible via
menus.
Response Time: 250 ms (dampening set
to 1).
Display: Backlit 4 digit LCD 0.4˝ height
LED indicators for set point and alarm sta­tus.
Electrical Connections: 15 pin male high
density D-Sub connection. 18˝ (46 cm)
cable with 10 conductors included.
Process Connections: 1/8˝ female NPT.
Side or back connections.
Mounting Orientation: Mount unit in verti­cal plane.
Size: 5˝ (127 mm) O.D. x 3-1/8˝ (79.38
mm).

Weight: 1.75 lbs. (794 g).
Agency Approvals: CE.

SWITCH SPECIFICATIONS
Switch Type: 2 SPDT relays.
Electrical Rating: 1 amp @ 30 VAC/VDC.
Set Point Adjustment: Adjustable via key-

pad on face.

DIMENSIONS

(4) 6-32 HOLES

EQUALLY SPACED ON A

5-1/8 (130.18) B.C.
PANEL MOUNTING

1/8 FEMALE NPT LOW

PRESSURE CONNECTION

1/8 FEMALE NPT HIGH

PRESSURE CONNECTION

2-1/16

(52.39)

2

(50.80)

1-1/4

(31.75)

ø4-47/64

(120.25)

Ø5

(127.00)

Ø4 (101.60)

FACE

5-1/2 (139.70) O.D.

MOUNTING RING

5/8 (15.88)

PANEL MAX

2-1/2

(63.50)

3/16

(4.76)

1/8 FEMALE NPT HIGH
PRESSURE CONNECTION

1/2

(

12.70)

1-9/32

(32.54)

1

1/16

(17.46)

30°

1-3/4

(44.45)

1/2 (12.70)

11/16

(17.46)

1/8 FEMALE NPT LOW

PRESSURE CONNECTION

(3) Ø3/16 (4.77) HOLES EQUALLY
SPACED ON A 4-1/8 (104.78) B.C.
SURFACE MOUNTING

1.800.868.7495

QualityInstruments-Direct.ca

INSTALLATION
LOCATION: Select a clean, dry location free from shock and vibration where temperature

limits will not be exceeded. Distance from the transmitter to the receiver is limited only by
total loop resistance. See ELECTRICAL CONNECTIONS. Tubing feeding pressure to the
instrument can be practically any length required, but long lengths will increase response
time slightly.

POSITION: All standard models are calibrated for use in a vertical mounting position.
Higher range models will perform properly at other angles but should be spanned and
zeroed in the position in which they will be used. Because of their sensitivity to gravitation­al forces, models with ranges under 1˝ w.c. (25.4 mm w.c.) must always be mounted ver­tically.

PRESSURE CONNECTIONS: For installation convenience two sets of 1/8˝ female NPT
pressure ports are supplied. Be sure to seal the unused ports with pipe plugs included.

Positive Pressure - Connect tubing to HIGH PRESSURE port and vent LOW PRESSURE
port to atmosphere.

Negative (Vacuum) Pressure - Connect tubing to LOW PRESSURE port and vent HIGH
PRESSURE port to atmosphere. (When operating this device in a dusty environment,
install an optional A-331 Filter Vent Plug in the vented port to keep interior clean.)

Differential Pressure - Connect tubing from the higher source to HIGH PRESSURE port
and from the lower source to LOW PRESSURE port.

3

1-1/2

[38.1]

5/16

[7.94]

11/16

[17.46]

3/4

[19.05]

1-3/32

[27.78]

1-3/4

[44.45]

1/2 [12.70]

(3) Ø3/16 [4.77] HOLES EQUALLY
SPACED ON A 4-1/8 [104.78] B.C.

Ø1/2 [12.70] HOLE FOR
LOW PRESSURE CONNECTION

Ø1/2 [12.70] HOLE FOR
HIGH PRESSURE CONNECTION

Fig. A

1.800.868.7495

QualityInstruments-Direct.ca

4

MOUNTING: The DH 3 may be either panel (flush) mounted or surface mounted.

Panel Mounting - Cut a 4-13/16˝ or 122 mm diameter hole in the panel and insert the unit

from the front. Slip on the mounting ring with the stepped side facing rear. Next, fit the snap
ring into the narrow groove at back edge of bezel. Thread four (6) 32 x 1-1/4˝ mounting
screws into tapped holes in mounting ring and set it against snap ring. Tighten screws
against rear of panel. See Fig. B.

Surface Mounting - Drill (3) 3/16˝ (4.76 mm) diameter holes for mounting and cut a 9/16˝
x 1-1/2˝ (14.3 x 38.1 mm) opening for access to terminal block as indicated in Fig. B. If rear
pressure connections are to be used, also provide 1/2˝ diameter holes as shown in Figs.
A and C. Insert 6-32 machine screws from rear of mounting surface, thread into tapped
holes on back of transmitter and tighten.

Fig. B

Fig. C

Ø4-3/4 [120.65] HOLE

PNEUMATIC
PRESSURE TAP S

SNAP RING

GROOVE

1.800.868.7495

QualityInstruments-Direct.ca

WIRING

The DH 3 uses a standard 15 pin male high density D-Sub connector available from
most electronic distributors. A pre-wired 18˝ cable is included with each unit.
See below table for cable color wiring information.

NOTES:

1. If 12-24 VDC power is used, the polairty is unimportant.

2. Wire in accordance with an equivalent national standard or code. Use copper conduc­tors only rated for 60°C.

3. All terminals are rated CLASS 2.

4. ISOLATION: All inputs and outputs to each other: 500 VAC.

5. 4-20 mA Transmitter – Check the specifications for the device receiving this signal for
input resistance. Typical 250 to 600 OHMS, 600 OHMS maximum.

5

Function

12-24 VAC/VDC Power
12-24 VAC/VDC Power
4-20mA XMTR Output ­4-20mA XMTR Output +
SP1 Relay N/O
SP1 Relay Com
SP1 RELAY N/C
SP2 or ALarm Relay N/O
SP2 or ALarm Relay Com
SP2 or ALarm Relay N/C

15 PIN Connector
Terminal

1
6
2
11
12
13
14
15
10
5

Cable Color

Brown
Yellow
Black
Red
Vilolet
Grey
White
Blue
Green
Orange

1.800.868.7495

QualityInstruments-Direct.ca

6

SP/ALSP/AL

M

ENUMENU

EE

RSTRST

Home
Position Function

Sequences the display
through SET POINT and
ALARM settings
Allows access to the menus

Displays full scale
range of unit

Clears or resets an Alarm
(alarm set for manual reset)

Main Menu Function

Return to home
position

Return to home
position

Sequences through
menus

Sequences through
menus

Enter into SUB MENU

Sub Menu Function

Return to home position

Return to previous menu

Increments a value

Decrements a value

Changes a value or
setting. Press ENTER and
display will blink. Adjust
with UP or DOWN arrows.
Press ENTER to store.
Display will stop blinking.

Peak/Valley SUB 
MENU resets display to
present value.

SP/AL

MENU

UP

ARROW

DOWN

ARROW

ENTER

RESET

KEY FUNCTIONS

INWCINWC

1.0001.000

SP1SP1

SP2SP2

ALHIALHI

ALLOALLO

SP/ALSP/AL

RSTRST

MENUMENU

EE

X1KX1K

FRONT PANEL

ALARM
DESCRIPTOR

UNITS

I

NPUT VALU E

MULTIPLIER

DESCRIPTOR

VISABLE WITH

SOME VELOCITY

A

ND FLOW

RANGES

SP2 DESCRIPTOR

SP1 DESCRIPTOR

1.800.868.7495

QualityInstruments-Direct.ca

7

SETTING SET POINTS AND ALARMS

The hot key provides direct access to the Set Point and Alarm MENU. The Set
Point and Alarm MENUS that are displayed are based upon the Control (CtrL) SUB
MENU.

S

P/ALSP/AL

S

P/ALSP/AL

S

P/ALSP/AL

SP/ALSP/AL SP/ALSP/AL

S

P/ALSP/AL

S

P/ALSP/AL

SP/ALSP/AL

SP/ALSP/AL SP/ALSP/AL

SP/ALSP/AL

S

P/ALSP/AL

S

P/ALSP/AL

Visible whenVisible when

Visible whenVisible when

Visible whenVisible when

mode =mode =

mode =mode =

mode =mode =

CONTROL MODECONTROL MODE

CONTROL MODECONTROL MODE

CONTROL MODECONTROL MODE

SET POINT ADJUSTMENT

Adjusting the DH

®

3 Set Points is quick and simple. Instead of setting a set point and dead-

band, simply adjust

SP1H

or

SP2H

for the desired relay turn on point, and then adjust

SP1L

or

SP2L

for the desired relay turn off point.

PRES

SURE

PRESSURE

00

00

TIMETIME

0.20.2

0.40.4

0.60.6

0.80.8

1.0

(in. w.c.)

In the above graph, an instrument with a 1.0˝ range would have the SP1 relay turn on at

0.8˝ and off at 0.4˝.

SP1H

sets the relay turn on point, and

SP1L

sets the relay turn off point.
The relays outputs normally function in the direct acting mode, which means the relays turn
on with an increase in pressure. SP1 may be configured to act as a reverse acting relay
(refer to the 1SP SUB MENU setting, page 15). When set for reverse acting,

SP1H

sets the

relay turn OFF point, and

SP1L

sets the relay turn ON point. SP2 is always direct acting.

SP/ALSP/AL

1.800.868.7495

QualityInstruments-Direct.ca

8

MENU MAPMENU MAP

CONTINUED

CONTINUED

SETTINGSSETTINGS

MAIN MENUS SUB MENUS

MENUS

UNAVAILABLE

FOR

BI-DIRECTIONAL

RANGES AND

RANGES ABOVE

25 IN. W.C.

EE

MENUMENU

1.800.868.7495

QualityInstruments-Direct.ca

9

CONTINUEDCONTINUED

SETTINGSSETTINGS

MAIN MENUS SUB MENUS

0PEn

EE

MENUMENU

1.800.868.7495

QualityInstruments-Direct.ca

10

MAIN MENUS SUB MENUS

SETTINGS

Menus present only

in pressure operation

EE

MENUMENU

1.800.868.7495

QualityInstruments-Direct.ca

11

M

ain Menu Selections (Upper Right Display Reads

M

ENU

)

SECr

Security - Lock out access to Set Point and Alarm settings, or lock out access to

all settings.

OPEr

Operation - Selection of Pressure, Velocity or Flow and corresponding engineering

units.

OUt

Output - Select a Single Set Point, 2 Set Points, or a Set Point and an Alarm

mode of operation.

d.S

Display - Monitor and adjust display related settings: Peak, Valley, display reso-

lution, % output and dampening.

AdU

Advanced functions - Modify advanced function parameters, transmitter output

scaling, Maintenance Set Point settings and calibration.

1.800.868.7495

QualityInstruments-Direct.ca

12

MAIN MENUS and SUB MENUS

SECr

(Security) MAIN MENU

SECr

is the only SUB MENU in the security MENU. When the security SUB MENU
is selected, the present security level is displayed in the upper right hand display. To
change the security level, adjust the number displayed to the number shown in the
following table for the desired security level.

The password values shown in the table cannot be altered, so retain a copy
of these pages for future reference.

OPEr

(Operation) MAIN MENU

The

OPEr

MENU selects the measurement type of the instrument.

The SUB MENUS are:

PrES

- Pressure

KFAC

- K Factor

XDIM

- X Dimension

UEL

- Velocity

ArEA

- Area

YDIM

- Y Dimension

FLO

- Flow

DIA

- Diameter

If the instrument is set for Velocity, the

OPEr

MENU will have an additional

KFAC

SUB

MENU. If the instrument is set for Flow, the

OPEr

MENU will have additional

KFAC

and

ArEA

SUB MENUS. These will be discussed under Velocity and Flow. When scrolling

through the

OPEr

SUB MENUS, the measurement type the unit is currently set for will
show the units in the upper right display. The other measurement types will have a blank
upper right display.

Security Level
Displayed

1
2

3

4

Access

All menus access

Menu Access
SP/AL Locked
SP/AL Access
Menus Locked
All settings locked

Password Value
to Enter

10

70

90

111

Units visible, so unit
is presently set to
measure pressure

is presently set to
measure pressure

Units not visibleUnits not visible Units not visibleUnits not visible

1.800.868.7495

QualityInstruments-Direct.ca

13

PrES

(Pressure) SUB MENU

For pressure measurement, the following units are available:

Table 1 Pressure Range vs. Available Units

INWC

.1000
.2500
.5000

1.000

2.500

5.000

10.00

25.00

50.00

100.0

FTWC

.2083
.4167
.8333

2.083

4.167

8.333

MMWC

2.540

6.350

12.70

25.40

63.50

127.0

254.0

635.0
1270
2540

CMWC

.2540
.6350

1.270

2.540

6.350

12.70

25.40

63.50

127.0

254.0

PSI

.1806
.3613
.9032

1.806

3.613

INHG

.1839
.3678
.7356

1.839

3.678

7.356

MMHG

.1868
.4671
.9342

1.868

4.671

9.342

18.68

46.71

93.42

186.8

MBAR

.2491
.6227

1.245

2.491

6.227

12.45

24.91

62.27

124.5

249.1

PA

24.91

62.27

124.5

249.1

622.7
1245
2491
6227

KPA

.1245
.2491
.6227

1.245

2.491

6.227

12.45

24.91

HPA

.2491
.6227

1.245

2.491

6.227

12.45

24.91

62.27

124.5

249.1

OZIN

.1445
.2890
.5780

1.445

2.890

5.780

14.45

28.90

57.80

UEL

(Velocity) SUB MENU

For velocity measurement, the following units are available:

SFPM

- Standard feet per minute

M/S

- Meters per second

Table 2 Available Velocity Ranges

NOTE: Air velocity and flow readings are based upon standard dry air conditions with an

ambient temperature of 70°F and a barometric pressure of 29.92 INHG.

INPUT RANGE
INWC

0 - 0.1
0 - 0.25
0 - 0.5
0 - 1
0 - 2.5
0 - 5
0 - 10
0 - 25

SFPM
RANGE

0 - 1266
0 - 2002
0 - 2832
0 - 4004
0 - 6332
0 - 8954
0 - 12.66 x IK
0 - 20.02 x IK

M/S RANGE

0 - 6.431
0 - 10.17
0 - 14.39
0 - 20.35
0 - 32.17
0 - 45.48
0 - 64.33
0 - 101.7

INWC

- Inches of water column

FTWC

- Feet of water column

MMWC

- Millimeters of water column

CMWC

- Centimeters of water column

PSI

- Pounds per square inch

INHG

- Inches of mercury

MMHG

- Millimeters of mercury

MBAR

- Millibar

PA

- Pascal

KPA

- Kilopascals

HPA

- Hectopascals

OZIN

- Ounce inches

NOTE:

OVFL

(over flow) or

UnFL

(under flow) will appear when the ranges have been

exceeded above or below full scale by 2%.

1.800.868.7495

QualityInstruments-Direct.ca

14

F

LO

(

Flow) SUB MENU

For flow measurements the following units are available:

SCFM

- Standard cubic feet per minute

M^3H

- Cubic meters per hour

FLO r

(Flow Range) SUB MENU

LO

- 99.99 x 1K flow range

HI

- 999.9 x 1K flow range

Tables 3-6 show the flow ranges available, and the maximum duct size that can be set
for each input range.

Table 3

FLOr = LO

Maximum Duct Size (English)

RANGE
IN WC

0.1

0.25

0.5
1

2.5
5
10
25

SCFM
RANGE

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

MAX. DUCT
SIZE, SQ.
FT.

78.9

49.9

35.3

24.9

15.7

11.1

7.8

4.9

KFAC

SUB MENU

KFAC

K Factor - becomes accessible if the instrument is set for Velocity or Flow.

When the DH3

®

is used with a Pitot tube, the manufacturer may specify a K

Factor. The adjustment range is 0.01 to 2.00. The factory setting is 1.

Table 4

FLOr = HI

Maximum Duct Size (English)

RANGE
IN WC

0.1

0.25

0.5
1

2.5
5
10
25

SCFM
RANGE

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

MAX. DUCT
SIZE, SQ.
FT.

789.8

499.5

353.1

249.7

157.9

111.7

78.9

49.9

Table 5

FLOr = LO

Maximum Duct Size (Metric)

RANGE
IN WC

0.1

0.25

0.5
1

2.5
5
10
25

Mˆ3/Hr
RANGE

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

99.99 x 1K

MAX. DUCT
SIZE Mˆ2

4.32

2.73

1.93

1.37

0.86

0.61

0.43

0.27

Table 6

FLOr = HI

Maximum Duct Size (Metric)

RANGE
IN WC

0.1

0.25

0.5
1

2.5
5
10
25

M

3

/Hr

Range

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

999.9 x 1K

MAX. DUCT
SIZE, M

2

43.19

27.31

19.3

13.64

8.63

6.10

4.31

2.73

1.800.868.7495

QualityInstruments-Direct.ca

15

A

rEA

,

D

IA

,

X

DIM

a

nd

Y

DIM

S

UB MENUS

These SUB MENUS become accessible if the instrument is set for flow. When measuring
flow, the area of the duct must be specified. Tables 3 and 4 show the input range vs max­imum flow and duct size. For a rectangular duct the maximum size is specified in square
feet or meters. For a circular duct the maximum size is specified as the diameter. X, Y and
circular dimensions are entered in feet with 0.01 foot resolution for

FLOr = LO

and 0.1 foot

resolution for

FLOr = HI

, or entered in millimeters with 1 millimeter resolution.

ArEA

- Area, select

CIR

for a circular duct or

RECT

for a rectangular duct. If a

circular duct is selected, the

DIA

SUB MENU will be activated. If a rectangular duct

is selected, the

XDIM

and

YDIM

SUB MENUS will be activated.

DIA

- Diameter, enter the diameter of a duct

XDIM

- Enter the “X” dimension of a duct

YDIM

- Enter the “Y” dimension of a duct

OUt

(Output) MAIN MENU

The

OUt

MENU selects the output type of the instrument. The SUB

MENUS are:

CtrL

- Control type

ALrE

- Alarm reset, manual or auto

ISP

- SP1 reverse or direct acting

AL.H

- Alarm inhibit

AL

- Alarm type

ALDL

- Alarm delay

Y

X

1.800.868.7495

QualityInstruments-Direct.ca

16

0

100

Process

Rever

se A

ct

i

ng

Tim

e

SPH

SPL

Relay Inactive

Relay Active

C

trL(Control) SUB MENU

1SP

- Single set point

2SP

- Two fully independent set points

SPAL

- Single set point and alarm

1SP

(SP1 Reverse or Direct Acting) SUB MENU

DIR

- Direct. Relay turns on with increasing pressure

REV

- Reverse. Relay turns on with decreasing pressure

0

100

Process

D

i

re

ct

Act

i

n

g

T

im

e

SPH

SPL

Relay Inactive

Relay Active

1.800.868.7495

QualityInstruments-Direct.ca

17

T

he following alarm function SUB MENUS are activated when

C

trL

i

s set to

S

PAL

:

AL

(Alarm Type) SUB MENU

HI

- High alarm

LO

- Low alarm

HILO

- For a high/low guardband type alarm

ALARM ADJUSTMENT

Alarm settings are dependent upon the selected alarm mode. The DH3

®

differential pres­sure controller alarm may be configured as a High Alarm, Low Alarm, or High/Low Alarm.
Alarm settings are all absolute and may be set to anywhere within the range of the instru­ment. The dead bands of the alarms are fixed at 1% of full scale.

MIN. PRESSURE

MAX. PRESSURE

ALHI

Relay OFF Relay ON

HIGH ALARM FUNCTION

MIN. PRESSURE

MAX. PRESSURE

ALLO

Relay ON Relay OFF

LOW ALARM FUNCTION

MIN. PRESSURE

MAX. PRESSURE

ALLO

Relay ON Relay OFF Relay ON

HIGH/LOW ALARM

FUNCTION

ALHI

1.800.868.7495

QualityInstruments-Direct.ca

18

A

L0S

(

Alarm Output State) SUB MENU

CL0S

- Alarm relay contacts close upon alarm condition

0PEN

- Alarm relay contacts open upon alarm condition

ALrE

(Alarm Reset) SUB MENU

ONOF

- Automatic reset

HOLD

- Manual reset. An alarm is reset by the RESET key on the front

panel, or an external reset switch.

AL.H

(Low Alarm Inhibit) SUB MENU

ON

- Alarm inhibit is on

OFF

- Alarm inhibit is off

If

AL.H

is selected ON, a low alarm condition is suspended upon power up until the

process value passes through the alarm set point once.

ALDL

(Alarm Delay) SUB MENU

Sets the amount of time an alarm condition must be continuously met before
the alarm condition is recognized. The alarm delay is adjustable from 0-3600
seconds.

d.S

(Display) MAIN MENU

PEAK

- Peak value

rESO

- Resolution

VALy

- Valley value

Pd.S

- Process display

ZERO

- Zero

DAMP

- Dampening level

PEAK

(Peak) SUB MENU

The Peak feature stores the highest pressure reading the instrument has measured
since the last reset or power up. At power up

PEAK

is reset to the present pressure

reading. To manually reset the

PEAK

value, press the RESET key while in the

PEAK

SUB MENU.

VALy

(Valley) SUB MENU

The valley feature stores the lowest pressure reading the instrument has measured
since the last reset or power up. At power up

VALy

is reset to the present pressure

reading. To manually reset the

VALy

value, press the RESET key while in the

VALy

SUB MENU.

1.800.868.7495

QualityInstruments-Direct.ca

19

r

ESO

(

Resolution) SUB MENU

The DH 3 is capable of displaying four digits of resolution. However, at very low
pressures the instability of the pressure may cause fluctuations in the least
significant digit causing the least significant digit to be of little value.
Three digit resolution (

3DIG

) can only be active when there is at least one digit to the

right of a decimal.

3DIG

- Set display for 3 digit resolution

4DIG

- Set display for 4 digit resolution

Pd.S

(Process Display) SUB MENU

STD

- Display reads pressure, velocity, or flow values

PCT

- Display reads % of full scale value

When the display is reading percent,

PCT

is displayed in the upper right of the

display. The percent display is only available in pressure operation.

DAMP

(Dampening) SUB MENU

Adjust from 1-16

Dampening stabilizes the display from instabilities due to things such as vibration and
excessive pressure fluctuations. The dampening setting adjusts the amount of
readings that are averaged for each display update. Adjust the dampening value until
the display reads a stable value for the application.

AdU

(Advanced) MAIN MENU

POL

- Process output low

ZERO

- Zero calibration

POH

- Process output high

SPAN

- Span calibration

MSP1

- Maintenance set point 1

MSP2

- Maintenance set point 2

POL

and

POH

(Process Output Low and High) SUB MENUS

This feature is used in pressure operation only.

Process output low and high are used to scale the 4-20 mA output. Set

POL

to the

desired display reading for 4mA output, and set

POH

to the desired display reading

for 20 mA output.

POH

must be higher than

POL. POL

may be adjusted 2% BELOW

minimum scale up to

POH. POH

may be adjusted from

POL

to 2% ABOVE maximum

scale.

1.800.868.7495

QualityInstruments-Direct.ca

M

SP1

a

nd

M

SP2

(

Maintenance Set Point 1 & 2) SUB MENUS

Adjust for the desired maintenance set points when the unit is placed in the
maintenance mode. The deadband is fixed at 2% of full scale. To enter or
leave the maintenance mode, press and hold the for 8 seconds.

ZERO

and

SPAN

(Calibration of Zero and Span) SUB MENUS

The lower display reads

CAL

in this mode.

ZERO

Calibration

NOTE: For accurate calibration, DO NOT apply any pressure when

performing this function.

With the display reading

ZERO

, press the ENTER key. The upper display will
blink. Press ENTER again to complete the zeroing of the instrument or press
the

MENU

key to cancel.

SPAN

Calibration

With the display set to

SPAN

, apply full scale pressure to the unit. Press the
ENTER key. The upper display will blink. Press ENTER again to complete the
calibration or press the

MENU

key to cancel.

SP/ALSP/AL

©Copyright 2012 Dwyer Instruments, Inc.

Printed in U.S.A. 2/12

FR# 443555-00 Rev.3

DWYER INSTRUMENTS, INC.

Phone: [phone] www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, IN 46360, U.S.A. Fax: [phone] e-mail: [e-mail]

1.800.868.7495

QualityInstruments-Direct.ca