Dwyer Instruments RP2 Operating Manual

Model RP2 Wireless Thermo-Hygrometer Probe for UHH

1-41/64

[41.62]

14-25/64 [365.39]

-3/64

[

153.63]

[

15.87]

-5/32

[

29.31]

5/16

[7.95]

Specifications - Installation and Operating Instructions

he Model RP2 Wireless Thermo-Hygrometer Probe measures relative

umidity, temperature, dew point, and wet bulb temperatures when combined with

he Model UHH Universal Handheld. In order to protect the sensor in higher air

t flow ducts, each probe comes with a membrane filter. Factory calibrated replacement humidity sensors can plug directly into the probe without requiring additional calibration.

Wireless probes can take measurements up to 50 feet away from the UHH. A bicolor LED flashes on the handle of the probe to indicate communication status with the handheld. The battery is rechargeable via the mini-USB connector on the bottom of the probe.

NOTICE

(1) This device may not cause harmful interference. and (2) this device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à des règlements d'Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) Ce dispositif ne doit pas causer d'interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant entraîner un fonctionnement indésirable.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

Bulletin TE-RP2

PECIFICATIONS

ervice: Clean air.

S Temperature Limits:

Process: -4 to 140°F (-20 to 60°C); Ambient: 5 to 125°F (-15 to 51°C); Battery Charging: 32 to 113°F (0 to 45°C).

Range:

RH: 0 to 100% (non-condensing); Temperature: -22 to 140°F (-30 to 60°C).

Accuracy:

RH: ±2% @ 25°C (10 to 90% RH); ±4% (0 to 10, 90 to 100% RH); Temperature: ±0.54°F @ 77°F (±0.3°C @ 25°C).

Response Time: 1.5 s. Probe Length: 8˝ (203 mm) insertion. Power Requirements: 3.7 V YT562447 Lithium ion battery, installed functional,

user replaceable.

Maximum Wireless Distance: 50´ (15 m). Handle Enclosure: Thermoplastic elastomer over polycarbonate. Supplied With: Wrist strap. Weight: 11.2 oz (331.22 g). Agency Approvals: CE (not while charging), RoHS, FCC compliant.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.

CHARGING BATTERY

NOTICE

When the charge of the battery is almost used up, the LED on the handle of the wireless probe will turn solid red. There is approximately 5 minutes of battery life left at this point. If the probe is not already paired to the UHH, it will not pair while in low battery condition.

Step 1: Open the USB cover on the bottom of the probe handle. Step 2: Plug the mini-USB connector end of the cable into the probe handle. Step 3: Plug the USB connector end of the cable into the port on the charger or PC. Step 4: Plug the charger into either an electrical outlet or car charging port (LED on the charger and the handle should both light up). Step 5: The LED on the handle will turn off when fully charged. Step 6: Remove charger from electrical outlet. Step 7: Remove USB connectors from the handle and the charger. Step 8: Replace the USB cover on the bottom of the probe handle.

It is required prior to the initial usage to charge the battery for 12 hours.

DWYER INSTRUMENTS, INC.

Phone: 219/879-8000 www.dwyer-inst.com

WARNING

Instruments, Inc. approved charging device in a well ventilated area away from any flammable materials or gases. Do not incinerate the battery. Only charge between 32 to 113°F (0 to 45°C).

NOTICE

Lithium ion polymer batteries are very volatile and can cause a fire if punctured or severely damaged. Only use a Dwyer

If desired, can be operated with USB cables less than 3 m in length when connected to the charger or PC.

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: 219/872-9057 e-mail: info@dwyermail.com

AIRING WIRELESS PROBES

. Turn on Model UHH Universal Handheld by pressing the button.

. Press the and buttons to scroll through the menu headings at the top of the

2 display.

3. When PROBE is highlighted, hit the button to access the probe menu.

4. Press the directional arrow to scroll through the sub-menu headings. The current elected parameter will be highlighted in yellow.

. When PAIRING MODE is highlighted, hit the button to access the pairing

ode.

. Turn on the wireless probe(s) to be paired. After a period of up to 15 to 20 seconds,

6 the UHH screen will update with the information about the wireless probe(s) just turned on.

NOTICE

. Press the button to scroll through the available probes. The current selected

robe will be highlighted in yellow.

8. When the desired probe to be paired is highlighted, hit the button to pair the

probe. Once it is paired, it will be removed from the list automatically.

9. Once all the desired probes are paired, press button.

0. Repeat step 9 to go back to the home screen and begin readings.

ELECTING A PROBE

In order to cycle through the probes that are paired to the Model UHH Universal Handheld, press the or buttons while in the view data mode.

SETTINGS

hen using the Model RP2 Wireless Thermo-Hygrometer Probe, the base unit can

isplay Relative Humidity, Dew Point, Wet Bulb Temperature, along with Temperature.

he settings allow users to select between relative humidity / wet bulb temperature /

T dew point, engineering units, measurement range, and which parameters to show on the display. To access the settings menus:

1. Press the or directional arrows to scroll through the menu headings at the

top of the display.

2. When PROBE is highlighted, hit the button to access the probe menu.

3. Press the directional arrow to scroll through the sub-menu headings. The

currently selected parameter will be highlighted in yellow.

Units Selection

1. When sub-menu TYPE (next to humidity or temperature) is highlighted, hit the

button to access the settings sub-menu.

2. Press the directional arrow to scroll through the parameter headings. The

currently selected parameter will be highlighted in yellow.

3. When UNITS is highlighted, press the button and the current units will be

highlighted.

4. Pressing the or buttons will cycle through the available units. If humidity is

selected for type, the units can be %RH, dew point in °F or °C, or wet bulb temperature in °F or °C.

5. Once the desired selection is made, press the button.

Display Measurements

NOTICE

can be turned off.

1. When SOURCE is highlighted, press the button and the measurement type

selected will be highlighted.

2. Pressing the or buttons will cycle through the available parameters.

3. Once the desired selection is made, press button.

4. In order to turn off the secondary displays, use the and to select the

measurement type that is not selected for the SOURCE.

5. When the desired sub-menu TYPE is highlighted, hit the button to access the

settings sub-menu.

6. Press the directional arrow to scroll through the parameter headings. The

currently selected parameter will be highlighted in yellow.

7. When VISIBLE is highlighted, press the button and either ON or OFF will be

highlighted. The measurement will be displayed when set to ON and not displayed when set to OFF.

8. Pressing the or buttons will alternate between ON and OFF.

9. Once the desired selection is made, press button.

f a probe does not appear, power the probe down, then power

t back on.

The measurements on the main display will always be displayed, but the measurements on the secondary displays

OGGING MEASUREMENTS

he UHH series can log the data being measured either a single point at a time or by

ontinuously logging at a user defined sample rate. When the trigger is selected to be

c a single point at a time, pressing the power button on the probe handle or the store button on the handheld will store a reading into the currently open file until the user creates a new file. If there is not a file open, the handheld will ask to create one. For

anual trigger, the power button on the probe handle or the store button on the base

nit will start the logging, and the logging will end after a user selected duration or

hen the power button on the probe handle or stop button on the handheld is

epressed. When the trigger is set for event, the user will select the upper and lower

d limit of a range and select whether the logging should take place while the measurements are within or outside of the range. The handheld can also record up to 2 minutes before the event (pre-trigger) and up to 24 hours after the event (post-

rigger). If the measurements don’t match the trigger event, a minimum elapsed data

apture time can be set.

ccessing Log Settings

1. Press the or arrows to scroll through the menu headings at the top of the display

2. When LOG is highlighted, hit the button to access the log menu. . Press the or arrows to scroll through the sub-menu headings. The currently

elected parameter will be highlighted in yellow.

. When the sub-menu RATE is highlighted, hit the arrow button to set the sampling

4 rate.

5. Use the and arrows to select the desired sampling rate.

6. Once the desired sampling rate is selected, press the arrow.

7. When the sub-menu FILE FORMAT is highlighted, hit the arrow button to hoose the file type.

. Use the and arrows to toggle between CSV and TSV file formats.

. Once the desired file format is selected, press the arrow.

10. When the sub-menu Media is highlighted, hit the arrow button to choose where

to save the files.

11. Use the and arrows to toggle between internal memory and the SD card, if

present.

12. Once the desired location is selected, press the arrow.

13. When the sub-menu TRIGGER is highlighted, hit the button to access the

trigger settings sub-menu.

14. Press the arrow to scroll through the parameter headings. The currently

selected parameter will be highlighted in yellow.

Selecting Trigger Source

1. When SOURCE is highlighted, press the arrow and the currently selected

parameter for the trigger source will be highlighted.

2. Press the or arrows to cycle through the available source.

3. Once the desired selection is made press the arrow.

Selecting Trigger Type

1. When the sub-menu TRIGGER is highlighted, hit the arrow and the currently

selected trigger type will be highlighted

2. Press the or arrows to cycle through the available trigger types.

3. Once the desired selection is made press the arrow.

Viewing Stored Files

1. Press the or arrows to scroll through the menu headings at the top of the

display.

2. When LOG is highlighted, hit the button to access the log menu.

3. Press the or arrow to scroll through the sub-menu headings. The currently

selected parameter will be highlighted in yellow.

4. When the sub-menu LOG FILES is highlighted, hit the arrow button to access

the log files.

5. Use the and arrows to select the desired log file.

6. Pressing the VIEW soft key will allow the user to view the first data point. The units,

sensor, time, and date will be shown for each data point.

7. Pressing the and arrows will cycle through all of the data points in the

selected file.

8. Data points can be deleted by pressing the DEL soft key.

9. Pressing the BACK soft key will exit out of the file.

10. Pressing the STAT soft key will show the average, peak, and valley statistics for

the data in the selected log file.

11. Pressing the BACK soft key will exit out of the file.

12. An entire file can be deleted by pressing the DELETE soft key.

13. To exit the LOG FILE sub-menu, press the arrow.

+ 2 hidden pages