Dwyer Instruments AQH-20 Operating Manual
Bulletin ES-AQH-1
81/4
[209.44]
63/4
[171.34]
RS
232
DC
9V
S
ET
HOLD
C
AL
Esc
M /AV
MODE
DP/WBT
N
X
2
11/64
[
55.07]
1
5/16
[
33.36]
MODE
DP/WBT
M /AV
N
X
DP/WBT
MODE
Model AQH-20 Handheld Indoor Air Quality Meter
Specifications - Installation and Operating Instructions
he Model AQH-20 Indoor Air Quality Meter reduces the number of instruments
T
a contractor has to carry by measuring the carbon dioxide concentration, air
temperature, and humidity in one device. A large backlit LCD display shows all
three parameters simultaneously. The Model AQH-20 can display dew point, or wet
bulb temperatures in place of the ambient temperature. Minimum, maximum, and
average readings are easily accessible through the function buttons. By pressing
the hold key, the current values are held so that they can be recorded. An audible
alarm warns the user that the current ambient conditions are becoming hazardous.
The Model AQH-20 includes a hard carrying case and four AA alkaline batteries.
OPERATING INSTRUCTIONS
Taking Measurements
Press the button to turn the meter on. The meter takes 30 seconds to warm up
before displaying the current reading.
CO
measurement is shown in top display
2
Air temperature, dew point, or wet bulb temperature is shown in lower left display
Humidity measurement is shown in lower right display
PECIFICATIONS
S
Measurement Ranges:
CO
: 0 to 2000 ppm.
2
Temperature: 14 to 140°F (-10 to 60°C).
Relative Humidity: 0.0 to 99.9% RH.
Accuracy:
CO
: ±30 ppm ±5% of reading;
2
Temperature: ±0.9°F (±0.6°C);
Humidity: ±3% RH (10 to 90%), ±5% (0.0 to 9.9% or 90 to 99.9%).
Resolution:
CO
: 1 ppm;
2
Temperature: 0.1°F (0.1°C);
Humidity: 0.1% RH.
Response Time:
CO
: < 30 seconds;
2
Temperature: < 2 minutes;
Humidity: <10 minutes.
Display: Four digits for temperature/CO
CO
Sensor: Non-dispersive infrared.
2
Operating Temperature: 32 to 122°F (0 to 50°C).
and 3 digits for humidity.
2
Operating Humidity (Non-Condensing): 0 to 95% RH.
Power Requirements: (4) 1.5 V AA alkaline batteries, included, user replaceable.
Warm Up Time: 30 seconds.
Weight: 6.76 oz (200 g).
Agency Approval: CE.
Selection of Temperature Parameter
The Model AQH-20 can display ambient air temperature, dew point temperature,
or the wet bulb temperature. Press the button to cycle between air
temperature, dew point temperature, and wet bulb temperature. The temperature
and measurement type will be displayed in the lower left corner of the display.
NOTICE
When Model AQH-20 experiences a large variation in
environment, the meter may take 30 seconds to respond.
Press the button for at least one second, to activate backlight. Do the same
to turn off the backlight.
Changing the CO
Hold down for more than one second during normal mode.
When “Al” and “P1.0” are displayed on the LCD, press the button to enter
alarm setup mode.
The current alarm value will be blinking on the LCD. “Al and P1.0” will be displayed
on the bottom displays. Press the button to increase the value and press the
Alarm Set Point
2
button to decrease the value.
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com
hen desired value is reached, press the button to save the value and
M /AV
N
X
M /AV
N
X
M
/AV
N
X
CAL
Esc
CAL
Esc
C
AL
Esc
DP/WBT
MODE
DP/WBT
M
/AV
N
X
C
AL
Esc
MODE
HOLD
CAL
Esc
HOLD
M /AV
N
X
W
eturn to the main menu or press button to return to main menu without
r
aving the changes.
s
If the alarm sounds, simply press any key (but power key) to silence the alarm.
Changing Engineering Units
old down for more than one second during normal mode to reach the main
H
enu.
m
ress the or the to toggle between alarm setup and unit setup.
P
O
C
alibration
C
2
he CO
T
n good weather conditions. Do not calibrate in areas with high CO
i
s
ensor should be calibrated in fresh outdoor air that is well ventilated and
s
2
uch as crowded areas.
oncentrations
c
2
Procedure:
1. Place meter in the calibration site.
. Turn the unit on and hold down and simultaneously to enter CO
2
alibration mode.
c
. “400ppm” and “CAL” should be blinking on the display.
3
. Wait 10 minutes until the blinking stops and the unit returns to normal mode.
4
2
When “Units” and “P3.0” are displayed on the LCD, press the button to
enter engineering unit setup.
he current temperature unit will be blinking on the lower left of the display. Press
T
he or the to toggle between Celsius and Fahrenheit.
t
When desired unit is set, press the button to save and return to the main
menu or press button to return to the main menu without saving the changes.
olding the Current Value
H
ress and release the to freeze the primary temperature display. “HOLD”
P
ill appear at the top left of the screen.
w
In order to return to normal operation, press the button again and the “HOLD”
icon disappears from the display.
ax, Min, and Average Data Functions
M
ress the button to cycle through the MIN, MAX, STEL, and TWA functions.
P
o exit, cycle through until none of the four mentioned functions appear on the
T
screen.
MIN and MAX readings show the minimum and maximum CO
main display, respectively. STEL and TWA readings show the weighted average of
the CO
readings on the main display. STEL uses all the CO2readings from the
2
past 15 minutes to calculate the average. TWA uses all the readings from the past
readings on the
2
8 hours to calculate the average. The current temperature and humidity continues
to be displayed at the bottom of the LCD.
NOTICE
Model AQH-20 requires at least 5 minutes worth of values in
order to calculate either of the CO
averages.
2
Automatic Power Off (Sleep Mode)
The instrument will shut off automatically after 20 minutes of operation to conserve
battery life if no button is pressed. To disable the sleep mode, press “Ø set” and the
“HOLD” buttons simultaneously before power on. An “n” icon will appear in the
center of the display once disabled.
To abort the calibration, turn the meter off at any time.
H Calibration
R
OTICE
N
The RH calibration should be done at 25ºC and humidity close
to the calibration salt being used (must at least be stable).
The RH must be calibrated with the default calibration salt. If not done properly and
with the correct salts, it will cause permanent damage.
3% Calibration Procedure:
3
. Plug sensor probe into 33% salt bottle.
1
2. Hold down and under normal mode to enter 33% calibration.
3. “CAL” and the calibrating value should be blinking on the LCD with current
temperature displayed but not blinking.
4. Wait about 60 minutes until “CAL” and the calibrating value stop blinking.
5% Calibration Procedure:
7
. After 33% calibration, plug the sensor probe into 75% salt bottle.
1
2. Press the button to enter 75% calibration mode.
3. “CAL” and the calibrating value should be blinking on the LCD with current
temperature displayed but not blinking.
4. Wait about 60 minutes until “CAL” and the calibrating value stop blinking and the
meter returns to normal mode.
Users can also calibrate either calibration point individually. For the 33% calibration
point, press the once the 33% calibration is complete. For the 75%
calibration point, press the or within the first five minutes while
initializing the 33% calibration.
MAINTENANCE
A periodic check of the system calibration is recommended. Model AQH-20 is not
field serviceable and should be returned if repair is needed (field repair should not
be attempted and may void warranty). Be sure to include a brief description of the
problem plus any relevant application notes. Contact customer service to receive a
return goods authorization number before shipping.
BATTERY REPLACEMENT
The Air Quality Handheld displays as a visual low battery indication.
When “Lob” appears on the LCD and a beeper sounds, the batteries must be
replaced.
NOTICE
If the unit fails to power on, it is likely that the batteries also need
to be replaced.
To Replace the Battery:
1. Make sure the unit is powered off.
2. Lay face down on a clean, flat surface.
3. Open battery compartment by pushing in tab and lifting cover.
4. Replace battery, taking note of the indicated polarity.
5. Replace the cover.
NOTICE
Failing to turn the handheld off may result in malfunction of the
unit. Dispose of used batteries promptly and keep away from
children.
©Copyright 2013 Dwyer Instruments, Inc. Printed in U.S.A. 8/13 FR# R6-443744-00 Rev.2
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com
Loading...