Dwyer Instruments 490W-6-HKIT, 490W-6-HKIT-NIST User manual

Bulletin TE-490W-QS

5/8

®

Series 490W Hydronic Differential Pressure Manometer ­Hydronic Application Software

Specications - Installation and Operating Instructions

Series 490W Hydronic Differential Pressure Manometer is the most accurate
and easy to operate manometer on the market. By using wireless transducers and
a versatile handheld, a single operator can monitor and balance a hydronic system
in less time than traditional hydronic balancers. The Series 490W utilizes mobile
technology to communicate via a Bluetooth connection with the transducers to

monitor differential pressure and ow on up to three different valves. Being wireless

means there are no hoses to carry, snag on equipment or needing to be drained. The
490W includes Dwyer’s Hydronic Application Software that contains valve charts for

numerous manufacturers, which converts differential pressure to ow directly on the

screen.

INCLUDED WITH THE 490W

1. Handheld test instrument with Dwyer Hydronic App preloaded onto device

2. Pressure transducers (4 per kit) with case

3. Installation and operating manual

4. 1/4˝ SAE 45° x 1/4˝ Male NPT straight adapter (2 per kit)

5. 1/4” Female elbow x 1/4˝ Male NPT tting (2 per kit)

6. Piercing gauge adapters [2 per size] (6 per kit)

-1/8˝ DIA x 1-1/2˝ length

-1/8˝ DIA x 3˝ length

-1/16˝ x 1-1/2˝ length

7. 490W fabric carrying case

8. Piercing gauge adapters and ttings case (2 per kit)

9. Charger cable and power adapter for handheld test instrument

3-17/64 [83]

6-17/64

[159]

SPECIFICATIONS

Wireless Distance: Up to 65´ (19.8 m).
Service: Compatible gases & liquids.
Wetted Materials: 316 SS, PTFE, brass.
Accuracy: 2% of reading, ±1 psi.

Compensated Temperature Range: 14 to 140°F (-10 to 60°C).

Pressure Hysteresis: ±0.25% FS.

Pressure Range: See chart.
Process Temperature Limits: -4 to 185°F (-20 to 85°C).

Display: 5˝ Gorrilla

Resolution: 0.01 psi.
Process Connections: Two 1/4˝ male NPT.
Power Requirements: CR2050 or CR2032 lithium battery, user replaceable.
Weight: 2 lb (907 g).
Agency Approvals: CE, FCC.

®

glass 3, touch screen, 1280x720.

[16]

1.000

2.940

.944
HEX

MODEL CHART
Model English Range Metric Range Maximum Range Available Engineering Units
490W-6-HKIT/NIST 0 to 50 psi, 0 to 200 psi 0 to 344.7 kPa, 0 to 1379 kPa 100 psi (6.89 bar), 400 psi (27.58 bar) psi, ft w.c., in w.c., Pa, kPa, hPa, cm w.c., mm w.c.
REPLACEMENT TRANSDUCERS

A-490W-1
A-490W-2
A-490W-3
A-490W-4
A-490W-5
A-490W-6

Find Quality Products Online at: [e-mail]

0 to 15 psi

0 to 30 psi

0 to 50 psi

0 to 100 psi

0 to 500 psi

0 to 200 psi

1.034 bar

2.069 bar

3.447 bar

6.895 bar

34.47 bar

13.79 bar

30 psig
60 psig
100 psig
200 psig
1000 psig
400 psig

psi, ft w.c., in w.c., Pa, kPa, hPa, cm w.c., mm w.c.
psi, ft w.c., in w.c., Pa, kPa, hPa, cm w.c., mm w.c.
psi, ft w.c., in w.c., Pa, kPa, hPa, cm w.c., mm w.c.
psi, ft w.c., in w.c., Pa, kPa, hPa, cm w.c., mm w.c.
psi, ft w.c., in w.c., Pa, kPa, hPa, cm w.c., mm w.c.
psi, ft w.c., in w.c., Pa, kPa, hPa, cm w.c., mm w.c.

Gorilla® is a registered trademark of Corning, Incorporated

www.GlobalTestSupply.com

FEATURE OUTLINE

Headset speaker

Headphone
connection with
integral protective

rubber cap

Camera

Power/sleep

button

Backlit

touchscreen
LCD

Handheld menu

button

OPERATION
Powering On/Off

To turn on the handheld, press and hold the power button. Wait approximately 15

seconds for it to fully power on. Swipe to unlock the unit.

To turn off the unit, either press and hold the power/sleep button and press Power Off
when prompted on the LCD or press the reset button.

Handheld Battery

The universal handheld utilizes an internal rechargeable battery. The battery symbol in
the top right of the screen shows the status of the battery.

TRANSDUCER BATTERY INSTALLATION

The unit is shipped with a CR2050 lithium battery installed. To replace battery, unscrew

black top cap from transducer. Tilt transducer to remove old battery. Install new battery
and replace top cap.

NOTICE

necessary, use only a CR2050 or CR2032 type such as a Sony CR2050W or

CR2032W.

Low Battery Indicator
A weak battery can cause improper operation or inaccurate measurements. The unit
is supplied with a battery that can last up to 2 years, depending on usage. When

transducers are sent in for annual recertication, the battery will be replaced.

Battery life depends on its capacity, operating temperature and
signal transmission interval. When battery replacement becomes

Handheld back

button

Handheld home

button

Figure 1

Volume
buttons

NOTICE

the battery is low, the battery symbol will turn red. When this occurs, use the included
USB charging cable and charging power adapter to recharge the unit.

NOTICE

When the 490W is received, the handheld test instrument will only
have a partial charge. Be sure to fully charge before using. When

The handheld test instrument comes factory paired to the included
wireless pressure transducers.

Rugged protective
housing

Speaker

Hand strap clip

Google Play™ is a trademark of Google, Inc.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Dwyer Hydronic App Operation

First turn on the handheld by pushing the power button (See Figure 1). Once fully

powered on, unlock the handheld by swiping the screen to the right. The Dwyer
Hydronic app is located at the bottom of the main screen. Click on the icon to open
the app.

Discovering the wireless pressure transducer

In the Sensor Discovery screen press the scan button to connect to transducers.
Note: In this screen, up to three sets of transducers may be paired simultaneously

to read differential pressure or up to six transducers may be may be paired to read

single pressure.

NOTICE

stopped by adding a Google Play

Valve Selection

Once the app is open, the Dwyer Hydronic App home screen will be shown. Press
the START button. The Valve Selection screen will now be displayed. Press the make
button to select a manufacturers valve. Then press the model button to select a valve
model. In the list of valve manufacturers, there is an option to choose a manual valve.

The ow coefcient (CV) is needed to use the manual valve, see Figure 2. Press the
next button to proceed.

Touch to

start app

When the app is opened, permission messages will pop up. This
can be bypassed by pressing ALLOW and can be permanently

®

account in the device’s settings menu.

NOTICE

(high) and blue (low) band to distinguish which transducer is high or low. Once the

transducers are paired by MAC Address, select the High Side box for the transducer

which has the red band. Its paired transducer will automatically be set to the low side.

After the high and low transducers are marked, press the Selected box to choose

pairs to use.

NOTICE

upon receiving communications from the Hydronic Application

Be sure the selected transducers’ MAC addresses have the
same maximum pressure. Each transducer is marked with a red

The transducers will automatically go into low power/sleep mode

to conserve battery energy. The transducers exit low power mode

Touch SCAN

button to scan for
transducers

Touch to

select valve

make and

model

Touch

the NEXT

button to

proceed

Figure 2

Select pair to
measure pressure

and ow

Low side is

automatically
selected once

high is chosen

Touch to mark
transducer as high

Figure 3

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ZEROING THE TRANSDUCERS

In order for the transducers to be zeroed, place them near the location of the process

connection. Note: Be sure to zero transducers outside the process connection without

any pressure applied.

In the Hydronic app, press the “Zero” button (Ø) to zero the pressure readings. The
zeroing process will began by displaying a dialog box “Zeroing Please Wait”. Once the
dialog box disappears, the transducers can be connected to the process connection

to read pressure.

Zero
button

Reading Differential Pressure and Flow

Data can be collected in the Flow Reading screen after the transducers connection
status indicates CONNECTED. The application converts differential pressure to ow

directly on the screen.

FCC RF EXPOSURE INFORMATION AND STATEMENT

The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device
types: S09 (FCC ID: ZHN-W63) has also been tested against this SAR limit. The
highest SAR value reported under this standard during product certication for use at

the ear is 0.430 W/kg and when properly worn on the body is 0.772 W/kg. This device

was tested for typical body-worn operations with the back of the handset kept 1.5
cm from the body. To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 1.5 cm separation distance between the user’s body and

the back of the handset. The use of belt clips, holsters, and similar accessories should
not contain metallic components in its assembly. The use of accessories that do not

satisfy these requirements may not comply with FCC RF exposure requirements and

should be avoided.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interface received, including interference that may cause
undesired operation.

Note: The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modication to this equipment. Such modications could void the user’s

authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by one of more of the
following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

MAINTENANCE/REPAIR

Upon nal installation of the Model 490W, no routine maintenance is required. The
Model 490W is not eld serviceable and should be returned if repair is needed. Field

repair should not be attempted and may void warranty.

WARRANTY/RETURN

Refer to “Terms and Conditions of Sale” in our catalog and on our website. Contact
customer service to receive a Return Goods Authorization Number before shipping the

product back for repair. Be sure to include a brief description of the problem plus any
additional application notes.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com