Dwyer WHP Manual

Bulletin W-WHP

5

[127.00]

2-1/2

[63.50]

1/2˝ NPT CONDUIT KNOCKOUT

3X 1/2˝ NPT

6 [152.40]

4-5/32

[105.41]

5

[127.00]

2-1/2

[63.50]

1/2˝ NPT
CONDUIT
KNOCKOUT

3X
1/2˝ NPT

6-3/4

[171.71]

2-3/4

[69.85]

1-1/16

[26.92]

4-1/2

[114.30]

COOL

WARM

Series WHP Wireless Humidity/Temperature Sensors

Specifications - Installation and Operating Instructions

WALL MOUNT

The Series WHP Wireless Humidity/Temperature Sensors provides flexibility in

locating sensors and reduces wiring cost. Using a 418 MHz transmitter, the sensor
can transmit data up to 100 feet without the use of a repeater. When coupled with
a receiver and output module, the Series WHP can output voltage, current or
resistance values for humidity and temperature. Since the unit is battery powered
using two AA batteries, users can change the location of the sensor to a different
wall or duct without worry about extra wiring cost. With the transmit rate at
approximately one reading every 10 seconds, the battery is estimated to last 5 to
8 years.

The duct mount and outside air mount sensors come standard with sintered filters
to protect the sensor from particulates. Set point adjustment and/or manual
override buttons are available on wall mount sensors.

OSA MOUNT

DUCT MOUNT

SPECIFICATIONS
Relative Humidity Range: 0 to 100%.
Temperature Range: -40 to 185°F (-40 to 85°C).
Accuracy: ±0.3°C, ±2% RH.
Temperature Limits: 32 to 140°F (0 to 60°C).
Power Requirements: (2) AA 3.6V lithium batteries.
Transmitter Interval Rate: Approximately 10-15 seconds.
Housing Material: ABS plastic.
Enclosure Rating: UL 94 V-0.
Antenna: 418 MHz - Built inside enclosure.
Weight: Dust/OSA: 1.25 lb (567 g); Wall: 0.25 lb (113 g).
FCC Approval: FCC ID# T4F061213RSO.
Agency Approvals: RoHS.

NOTICE

DWYER INSTRUMENTS, INC.

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: [phone] e-mail: [e-mail]

When inserting batteries, observe polarity markings
inside unit for proper operation.

Phone: [phone] www.dwyer-inst.com

MOUNTING

FIGURE 1: Mounting Diagram

OSA/Duct Sensors

Mount unit to surface using four #10 screws through the holes in the mounting feet.
For concrete or cinder block, pre-drill four 5/32˝ (4 mm) holes to 1-3/4˝ (45 mm)
depth. On duct models, only compress gasket half of original thickness. For OSA
models, follow orientation as shown in Figure 2.

FIGURE 2: OSA Mounting Orientation

Wall

Use the base plate to mark two holes on the surface that the sensor will be
mounted. Drill two 3/16˝ holes in the center of each marking. Insert drywall anchor
into each hole. Attach back plate to surface using the provided #6 screws into
anchors. Attach cover and use Allen wrench to tighten locking screw until it is flush
with bottom of cover.

Training Output Models

• Attach desired output modules to receiver as described in output
module manual.

• Apply power to the receiver and output modules (LED on receiver
should be lit. LED on output module will flash and go out).

• Remove cover of sensor and install the batteries (observe polarity).
LED next to the transmitter training button will flash every 10 seconds.

• Press and hold the plastic service button on the output module to be
programmed. At the same time, press for one second and release the
button on the sensor. When the LED on the output module lights,
release the service button. The LED on the output module will go out
after the button is released.

• Output module LED will flash when it receives data from sensor.

• Use same procedure for other modules.

• Close cover when all of the output modules have been trained.

FIGURE 3: Battery Polarity

DIAGNOSTICS

Error

Temperature or humidity
reading is incorrect

Temperature or humidity
reading is coming out of
wrong output module

MAINTENANCE, CLEANING AND REPAIR

After final installation of the unit, no routine maintenance is required. A periodic
check of the system calibration is recommended. The Series WHP is not field
serviceable and should be returned if repair is needed (field repair should not be
attempted and may void warranty). Be sure to include a brief description of the
problem plus any relevant application notes. Contact customer service to receive
a return goods authorization number before shipping.

Required Action(s)

• Check wire from output modules to
controller for proper connections and
polarities.

• Check to see if the controller’s software
is configured correctly.

• Check transmitter to see if its LED
flashes every 10 seconds. If not, change
batteries.

• Check power to the receiver and output
module.

• Check output module LED. If blinking
fast, retrain output module.

• Retrain output module.

©Copyright 2009 Dwyer Instruments, Inc. Printed in U.S.A. 12/09 FR# R6-443761-00

DWYER INSTRUMENTS, INC.

Phone: [phone] www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: [phone] e-mail: [e-mail]