Dwyer SSR-15 User Manual

3. Installation of Sensor Switch and Running of Field Wiring: (Cont)

Reference: Item D, previous page:

SSR-15

GROUP CAPACITANCE INDUCTANCE
A & B 0.6 uf 1.3 mh
C, E 1.9 uf 5.4 mh
D,F,G 1.9 uf 10 mh

Solid State Relay Model SSR-15

Instruction Bulletin

Example: Typical values of capacitance for a twisted pair of copper wires
is between 20 and 60 pf per foot. Using a maximum value of 60 pf/Ft,
groups A & B could have a run of 1500+ feet with safety. Inductance of a
typical twisted pair is between 0.10 and 0.20 uh/Ft, thus making a cable
run in this example essentially determined by the capacitance.

MAINTENANCE/REPAIR

Regular maintenance of the total system is recommended to assure sustained optimum performance. These
devices are not field repairable and should be returned to the factory if recalibration or other service is required.
After first obtaining a Returned Goods Authorization (RGA) number, send the unit freight prepaid to the
following. Please include a clear description of the problem plus any application information available.
Dwyer Instruments, Inc.
Attn: Repair Department
102 Highway 212

Michigan City, IN 46360

Important Points!

Product must be maintained and installed in strict accordance with the National Electrical

Code and Dwyer technical brochure and instruction bulletin. Failure to observe this warn­ing could result in serious injuries or damages.
An appropriate explosion-proof enclosure or intrinsically safe interface device must be
used for hazardous area applications involving such things as (but not limited to) ignitable
mixtures, combustible dust and flammable materials.
Pressure and temperature limitations shown on individual catalog pages and drawings
for the specified Dwyer products must not be exceeded. These pressures and tempera­tures take into consideration possible system surge pressures/temperatures and their fre­quencies.
Selection of materials for compatibility with the media is critical to the life and operation
of Dwyer products. Take care in the proper selection of materials of construction; particu­larly wetted materials.
Life expectancy of switch contacts varies with applications. Contact Dwyer if life
cycle testing is required.
Ambient temperature changes do affect switch set points, since the specific gravity of
a liquid can vary with temperature.
Dwyer products have been designed to resist shock and vibration; however, shock and
vibration should be minimized.
Liquid media containing particulate and/or debris should be filtered to ensure proper
operation of Dwyer products.
Electrical entries and mounting points may require liquid/vapor sealing if located in an
enclosed tank.
Dwyer products must not be field repaired. Physical damaged sustained by the product
may render it unserviceable.

DWYER INSTRUMENTS,INC.

P .O.BOX 373 MICHIGAN CITY, INDIANA 46361, U.S.A.

Phone: [phone] www.dwyer-inst.com
Fax: [phone] e-mail: [e-mail]
Lit-By Fax: [phone]

For use as “intrinsically safe switch connections” to non-voltage producing
sensors in the hazardous location. When the SSR installation is in accor­dance with this guide, these switch terminals are suitable for connection to
Class I; Division 1,2; Groups A, B, C & D and Class II; Division 1, 2; Groups
E, F, G and Class III, as defined by Article 500 of the National Electric Code.

IMPORTANT!

Read the following carefully and completely

before installing or connecting SSR units:

1. Associated Equipment - Caution: The SSR must be mounted outside the
hazardous area. Only the switch or sensor terminals provide an intrinsically
safe switch circuit (see Fig. 1.) [Exia] means associated equipment:
“Appareillage connexe”; located in safe area.

Fig. 1.

Connection Diagram: Dwyer SSR Models

VAC

Neutral

Hot

FUSE F1

LOAD

**

[Exia]

SSR

Non-Hazardous
Location

Hazardous
Location

Simple

Apparatus

Note: For 120V application, only one fuse is required in the ungrounded
circuit of the input line.

** Required torque on these terminals not to exceed 10 IN-LB on
stranded wire; 8 IN-LB on solid wire.

2. Mounting and Enclosure Considerations:
Field wiring of intrinsically safe circuits is to be segregated from non-

A.

intrinsically safe wiring by use of suitable barriers, separate wireways or
trays (See Fig. 2). Wire insulation to be .010", minimum.

Fig. 2.

Multiple SSR units Grouped on

Common Earth-Grounded Mounting Plate

Located in Non-Hazardous Area

Earth Ground

(2 Places)

Common

Earth Ground

Mounting Plate

Resistance to Gnd.
must be less than 1
ohm from mounting
screw or bracket to
earthing member to
insure integrity.

Non-Intrinsically

Safe Wiring

Fig. 3. Unit Mounting Detail

SSR-15

* Note:
Lockwashers to be internal
or external tooth-type.

Mounting Plate

Mounting Plate Grounding Detail

Fig. 4.

Mounting Plate

* Lockwasher

Nut

* Lockwasher

Notes:

Installation of Sensor Switch and Running of Field Wiring:

3.

1. Grounding Hardware to be #8 or larger and Stainless Steel.

2. * Lockwashers to be internal or external tooth-type.

Screw

* Lockwasher

Nut

#10 Screw

* #10 Lockwasher

* #10 Lockwasher

#10 Nut

Terminal Lug

Intrinsically Safe
Wiring to Sensors
Located in Hazardous
Area

Note:

All intrinsically safe wiring must be segregated from non-intrinsically

safe wiring and shall have a minimum insulation thickness of .010”.

Intrinsically safe and non-intrinsically safe connection points should be

B.

located sufficiently apart to prevent any possibility of bypassing or miswiring
during installation or servicing of equipment.

The enclosure shall contain a cautionary statement as follows: “CAUTION:

C.

ANY SUBSTITUTION OF COMPONENTS MA Y IMP AIR INTRINSIC
SAFETY”.

The SSR mounting bracket must be grounded to insure intrinsic safety.

D.

Resistance between bracket and ground electrode should be below one
ohm. (See Fig. 3 and Fig. 4 for recommended selection of grounding
hardware and refer to Article 250 of the National Electrical Code for methods

and practices.)

A. It is expected that the installation will be in accordance with Article 504 of the N.E.C.,

ANSI/NFP A 70 and/or C.E.C. Part 1*.

*Note: This is a CSA requirement. C.E.C. = Canadian Electrical Code.

B. The nature of the sensor switch must be that it is a non-voltage-producing, essentially

resitive device, containing no energy-storing components. (Simple Apparatus -flow
switches, level switches, pressure switches.)

C. The conductors of the intrinsically safe circuit should be sealed in a rigid metal conduit

at the point where the wiring enters the hazardous area. The wiring and contacting
device should be such that conductive dusts in the area will not close the circuit in
place of the contacts.

D. Hazardous area field wiring will store energy due to distributed capacitance and

inductance in proportion to its length. It is therefore recommended that the characteris­tics (available from the manufacturer) of the cable be known and judged against the
length of run and atmosphere of exposure. The conservative chart on the next page is
presented as a requirement in determining the limits of reactance for signal loops in
the hazardous area wiring for the SSR series.

E. Whenever possible, the actual measured parameters should be used in making the

determination of allowable length.

F. Shielded cable is not required; but if used in the application, the shield must be returned

to ground - the same as the SSR mounting bracket.

G. Non-intrinsically safe wiring cannot be run in conduit or open raceways together with

intrinsically safe wiring.