Dwyer SC4151 User Manual

IsoVerter®II

®

Models SC4130, SCL4130, SC4151 & SCL4151

INST ALLATION INSTRUCTIONS

Getting Started

1.) Using a small screwdriver, ball point pen, etc. set the Output Switch
(SW-1) on the side of the unit (see Output Programming on page 2).

2.) Mount unit into panel. (see Mounting on page 2).

3.) Connect unit to input signal, output signal, and power wiring (see Wir­ing on page 3).

4.) Check calibration (See Calibration on page 3).

Specifications are on page 4.

Dimensions

22.5

(0.886)

POWER

ZERO

SPAN

75

(2.950)

INPUT

1

4

+

OUTPUT

7

0

1

POWER

INPUTRANGE:

S/N:

MODEL:

+

_

2

3

6

5

290-2886

DIV.OF DWYERINSTRUMENTS,INC.

MICHIGANCITY, IN 46361,U.S.A.

MADEIN U.S.A.

_

8

9

2

1

1

1

ISO-VERTER®

CURRENT 4-20mA

II

LOVE CONTROLS

DIN EN 50022-35

(not supplied)

NOT

BLANK==APPLICABLE

KEY

OFF

ON

VOLTAGE 0-10V

OUTPUT RANGE

SW1

1 2 3456

123456

ON

35.5

(1.40)

98.5

(3.880)

ADAPTER BRACKET
FOR SURFACE
MOUNTING (OPTIONAL)
KIT#: 1007-35DINADPTR

Dimensions in
millimeters (inches)

9

12

8
7

11
10

LOVE CONTROLS

LOVE

®

949-0528-2 Page 1 of 4 June, 2000

a Division of Dwyer Instruments, Incorporated

PO Box 338 Michigan City, IN 46361-0338

[phone] [phone] FAX [phone]

❍

❍

❍

www.love-controls.com

Output Programming

T

MODE SELECTION SWITCH BANK (SW-1)

1. For VOLTAGE OUTPUT (0 to 10 VDC) turn switches one, two,

and three ON and switches four, five, and six OFF.

2. For CURRENT OUTPUT (4 to 20 mADC) turn switches one, two,

and three OFF and switches four, five, and six ON

ON

KEY

ON
OFF

BLANK =
NOT
APPLICABLE

VOLTAGE 0-10 V
CURRENT 4-20 mA

1 2 3 4 5 6

SW1

OUTPUT RANGE

1 2 3456

W ARNING: Do not attempt to operate this de­vice with the cover removed. Potentially le­thal voltage is present on some of the internal
components. Do not open the unit. There are
no internal adjustments or user serviceable
parts in the unit.

Mounting

Mount the unit in a panel that will not be subject to excessive tempera­ture, shock, or vibration. All models are designed for mounting on an
industry standard 35 mm DIN rail. An optional surf ace mount­ing kit is available from the factory (P/N 35DINADPTR).

To install hold the SC4130 / SCL4130 / SC4151 / SCL4151 so
that is the front is higher than the rear. Place the upper slot
on the rear of the SC4130 / SCL4130 / SC4151 / SCL4151 on
the top edge of the DIN rail. Slowly rotate the front down until
the bottom spring clip snaps over the bottom edge of the DIN
rail.

To remove from the DIN rail, place a small slotted screw­driver in the slot in the spring clip under the housing. Pry the
slot downward to release the SC4130 / SCL4130 / SC4151 /
SCL4151 from the bottom of the rail.

Slot

June, 2000 Page 2 of 4 949-0528-2