dweLED DWLE1206 Installation & Assembly

INSTALLATION INSTRUCTION

877 - LED Pendant

PD-87720, PD-87723, PD-87735

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

HARDWARE

A

A1 B1 C1 D1 E1

B

C

D

E

Wire Connector

Wire Connector

Qty: 3pcs+1 Extra

Qty: 3 pcs + 1 Extra

P3

P3

waclighting.com

Phone [phone]
Fax [phone]

Junction Box Screw

Junction Box Screw

Qty: 2pcs+1 Extra

Qty: 2 pcs + 1 Extra

8#-32×13/16

#8-32x13/16

Nickel Plating

Nickel Plating

Mounting Screw

Mounting Screw

Qty:1 Extra
5/32"-32×1/2
Chrome Plating(CH)

Qty: 1 Extra

5/32"-32x1/2

Chrome Plating

White Painting(WT)

Headquarters/Eastern Distribution Center

44 Harbor Park Drive
Port Washington, NY 11050

Screw
Qty:1 Extra
M3×5
Chrome Plating(CH)

Screw

Qty: 1 Extra

M3x5

Chrome Plating

White Painting(WT)

Central Distribution Center

1600 Distribution Ct
Lithia Springs, GA 30122

Optional Metal Cap

Qty:1 Extra
Chrome Plating(CH)
White Painting(WT)

Western Distribution Center

1750 Archibald Avenue
Ontario, CA 91760

Optional Metal Clip

Qty: 1 Extra

Chrome Plating

1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.

INSTALLATION INSTRUCTION

877 - LED Pendant

PD-87720, PD-87723, PD-87735

FIG. 1 PD87720PD87735 PD87723

PD-87735

PD-87720 PD-87723

Junction Box

Ground Wire

Ground Wire Screw

Wire Connector

Junction Box Screw

A

A1

B

B1

Ground Wire Screw

Plate

Mounting Plate

Canopy

C

Driver

C1

Cable Gripper

Back Plate Dimensions

Mounting Screw

Driver

1 3/4"

PD-87720: Ø6 3/16"
PD-87723: Ø6 3/4"
PD-87735: Ø6 3/4"

Plastic Clip

Plastic

Screw

Push up

fi

D1

D

1 3/8"

G

N

D

PREPARATION

1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.

2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.

CONNECTING THE WIRES (Fig. 2)

PREPARATION

3. Remove the mounting screw (C) from the canopy.

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

4. Secure the mounting back plate to the junction box using junction box screws (B). The side of the mounting back plate marked”GND”

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

must face out.

5. Adjust the fixture wire length by pushing the cable gripper on the canopy and pulling the wire as desired. Make sure the wires are

CONNECTING THE WIRES (Fig. 2)

the same length.

3. Remove the mounting screws (C1) from the canopy.

a. Retract these wires close to a desirable length to within the canopy before securing the fixture in place. Using the cable gripper

4. Secure the mounting back plate to the junction box using junction box screws (B1). The side of the mounting back plate marked “GND”

to adjust more than 18” of wire length is not desirable.

must face out.

b. Warning: Shortening these cables without professional helps or electronic background is not advisable. Any modifications to the

5. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired. Make sure the wires are

fixture will result in voiding the warranty of the product.

the same length.

6. Connect the Driver’s input wires to junction box wires as shown in Fig. 2,

6. Connect the Driver’s input wires to junction box wires as shown in Fig. 2,

making sure that all wire connectors (A) are secured. If your outlet box has a

making sure that all wire connectors (A1) are secured. If your outlet box has

green or bare copper ground wire, connect the fixture’s ground wire to it.

a green or bare copper ground wire, connect the xture’s ground wire to it.

Otherwise, connect the fixture’s ground wire directly to the back plate using

Otherwise, connect the xture’s ground wire directly to the back plate using

the green screw provided. After wires are connected, tuck them carefully

the green screw provided. After wires are connected, tuck them carefully

inside the junction box.

inside the junction box.

MOUNTING THE FIXTURE(Fig.1)

MOUNTING THE FIXTURE (Fig. 1)

7. Secure the canopy to the mounting plate using the mounting screws (C1).

7. Secure the canopy to the mounting plate using the mounting screws(C)

8. There is optional metal clip in hardware bag, remove the screws (D1) to replace

8. There is optional metal clip in hardware bag, remove the screw (D) to

the plastic clip, secure the metal clip with screws (D1).

replace the plastic clip, secure the metal clip with screw (D).

Fig. 2 Wiring

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare wire
(Ground)

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

waclighting.com

Phone [phone]
Fax [phone]

Headquarters/Eastern Distribution Center

44 Harbor Park Drive
Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct
Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue
Ontario, CA 91760

2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.