dweLED CBWR1195 Installation & Assembly

INSTALLATION INSTRUCTIONS

639-LED Pendant

PD-63944

CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.

• Read all instructions before installing.

• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

• When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.

• Retain installation instructions for future maintenance reference.

WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.

MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.

• Lisez toutes les instructions avant l’installation.

• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux

règlements locaux.

• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un chiffon humide.

HARDWARE

Wire Connector Qty: 3 pcs+1 Extra

dweLED.com

Phone (800) 526.2588 Fax (800) 526.2585

dweLED retains the right to modify the design of our products at any time as part of the company's continuous impro

Headquarters/Eastern Distribution Center

44 Harbor Park Drive Port Washington, NY 11050

Wire Connector Qty: 2 pcs+1 Extra

Mounting Screw Qty: 1 Extra

Central Distribution Center

1600 Distribution Ct Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue Ontario, CA 91760

vement program. Feb 2019

INSTALLATION INSTRUCTIONS

639-LED Pendant

PD-63944

PREPARATION

MOUNTING THE FIXTURE (FIG. 1)

4. Secure the mounting back plate to the junction box using the screws provided with the junction box.

NOTE: The side of the mounting plate marked “GND” must face out.

5. Choose the number of downrods suitable to your application.

CONNECTING THE WIRES

7. Connect the driver input/output wires with junction box wires as shown . Make sure that all wire connectors (A, B) are secure.

ground wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.

NOTE: DIMMING WIRING INSTRUCTIONS

his fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wires information.

1. T

2. To utilize ELV or TRAIC dimming: use black (hot), white (neutral) and bare copper ground wire s (ground).

3. To utilize 0-10V dimming: use purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wire s (ground). NOTE: Make sure to connect 0-10V prior to powering up the fixture in order to allow the 0-10V dimming to function properly.

FIG.1

6” Rod

Wire Connector

To Fixture

3-12” Rod

Junction Box

Ground Wire

Mounting Plate

Junction Box Screw

Driver (3

Mounting Screw

2/3”L X 32/3”W X 5/8”H)

Fixture

Back Plate Dimensions

FIG.2 SEALING

FIG.3

Black - Hot

White - Neutral

13/4”

3/8”

Fixture Wires

Black or Smooth

Fixture Wires

White or Ribbed

Fixture Wires Bare Wire (Ground)

3/8”

House Wires

Black (Hot)

House Wires

White (Neutral)

House Wires Green or Bare Copper (Ground)

Purple - Dim+

Gray - Dim-

Red - Fixture+ Black - Fixture-