DW Drums 2000 Series Owner`s Manual

Thank you for purchasing this DW pedal. It has been designed and
manufactured to provide a lifetime of trouble-free service. Please take a moment to familiarize yourself with the exclusive features and operating suggestions contained in this manual in order to ensure its optimum performance. Should you have any further questions, feel free to contact your local authorized DW dealer.
-Don Lombardi President, Drum Workshop, Inc
DW Pedal 5-Year Limited Warranty
For a period of ve years from the date of purchase, Drum Workshop, Inc. guarantees the original owner when presented with proof of purchase, that all 2000 Series Bass Drum Pedal cast parts are free of material and manufacturing defects. This warranty is limited to cast parts only such as the base casting, footboard, beater hub, sprocket, heel and cam casting. This warranty does not include moving parts such as the spring assembly, beater ball, hex shaft, ball bearings, etc. Moving parts have a six month warranty from the date of purchase. If under normal playing conditions parts covered in the limited ve year warranty fail, they will be replaced at no charge. Return the pedal to your authorized DW dealer, or if there is not a dealer in your area, contact DW directly. DO NOT send pedal to DW without rst receiving a Return Authorization (RA) number. Shipping charges to DW will be paid by the consumer.
OWNER’S MANUAL
2000 Series Bass Drum Pedals
DRUM WORKSHOP INC.
3450 Lunar Court - Oxnard, CA 93030 USA
www.dwdrums.com
www.dwdrums.com
to the desired position, then retighten the key screws. of key screws on the middle section of the linkage and adjust the length and angle of the linkage correct playing position, attach the linkage and tighten the auxiliary side key screw. Loosen the set tightening the key screw. Rotate the beater, casting and hex shaft on the auxiliary pedal to the Use the provided drum key or any standard drum key to secure the linkage to the primary pedal by
need to heat them with a heat gun or hair dryer for 2-3 minutes. loosening during playing. In order to loosen the chemical lock holding these screws, you may rst Note: Some of the screws on the pedal have been treated with a chemical lock to prevent unwanted
Primary Pedal
Pedal Plate
Spur
Hoop Clamp Key Screw
Adjustment Nut Spring Tension
Hoop Clamp
Spring
Rocker Hub
Stroke Adjustment
Beater Hub
Beater Shaft
Two-Way Beater
Double Pedal Linkage
Auxiliary Pedal
Heel Plate
Footboard
Base Casting
Single Chain
Accelerator Sprocket
Attaching and adjusting the linkage assembly (Double Pedals)-
for most general playing situations and preferred by many drummers. as directed by moving it to an alternate hole in the sprocket. The factory settings are recommended the chain, carefully remove the master link connector from the chain and sprocket and reposition it with the beater height and stroke adjustment, the length of the stroke. To change the position of The length of the chain determines the angle of the footboard and, when adjusted in combination
Chain Position & Footboard Angle Adjustment-
pedals to prevent bass drum crawl. All DW Bass Drum Pedals include built in adjustable spurs and non-skid Velcro on the bottom of the
Non-Skid Spurs and Velcro-
hoop protector to avoid damage to the bass drum hoop. pedal on the center of the hoop and tighten the side key screw securely. Use the provided rubber The DW Toe Clamp is designed to t a wide variety of manufacturers’ bass drum hoops. Position the
Hoop Clamp-
lock in the adjustment. the lock nut to create the desired tension, then release the hex nut and retighten the knurled nut to the spring assembly and pull down on the spring to release the locking hex nut. Tighten or loosen mechanism. To increase or decrease the spring tension, loosen the round knurled nut at the base of DW drum pedal springs feature an internal noise reduction damper as well as a tension locking
Spring Tension-
hard plastic side for a brighter attack, much like wood, but without the weight. The standard Two-Way Beater has both a curved, medium felt side for a warmer attack and a at,
Beater Playing Surface-
height is achieved, secure the beater shaft by tightening the beater hub key screw. beater should hit the center or an area 1-2 inches above the center of the drum. Once the desired The length of the beater shaft can be adjusted to achieve the desired feel and impact area. The
Beater Height-
Stroke Adjustment-
Loading...