Page 1
DVTEL INC.
65 Challenger Road
Ridgefield Park, NJ 07660
The contents of this guide may not be reproduced
or reprinted in whole or in part without the
express written permission of DVTEL, Inc.
ioi HD CB-5222
Bullet Analytic IP Camera
User and Installation Guide
Rev 0.18 January 21, 2016
Page 2
Table of Contents
Table of Contents
1 Document Information ........................................................................................................... v
2 Overview ............................................................................................................................... 1
Features ................................................................................................................................. 1
Package Contents .................................................................................................................. 2
3 Introduction to the CB-5222 Analytic Bullet IP Camera ............................................................ 3
CB-5222 Camera Dimensions ................................................................................................ 3
System Cable ......................................................................................................................... 4
3.2.1 Alarm Input/Output Pin-out .............................................................................................. 5
3.2.2 Power Input/Output Pin-out ............................................................................................. 5
3.2.3 Waterproofing the Camera Cable Connectors .................................................................. 7
3.2.4 Connecting the Unit to the Network ................................................................................. 8
3.2.5 Connecting Power to the Camera ..................................................................................... 8
4 System Requirements ............................................................................................................ 9
5 Installation .......................................................................................................................... 11
Setting the Camera’s Focal Length ...................................................................................... 11
Initial Camera Configuration ............................................................................................... 11
Camera Mounting Instructions ............................................................................................ 13
6 Using the DNA Utility to Search and Access the Camera ........................................................ 15
7 Using the Web Browser to Access the Camera ...................................................................... 17
8 Adjusting and Framing-Up the Camera View ......................................................................... 19
9 Configuration and Operation ................................................................................................ 20
CB-5222 Web Interface ....................................................................................................... 20
Settings ................................................................................................................................ 24
9.2.1 System Settings ............................................................................................................... 24
9.2.2 Streaming Settings .......................................................................................................... 48
9.2.3 Camera Settings .............................................................................................................. 53
9.2.4 Analytics Settings ............................................................................................................ 63
Log Out ................................................................................................................................ 86
Appendices ................................................................................................................................ 87
i
Page 3
CB-5222 User and Installation Guide
Technical Specifications ....................................................................................................... 88
Internet Security Settings .................................................................................................... 91
Install UPnP Components .................................................................................................... 93
Deleting the Existing DVPlayer ............................................................................................ 95
Deleting Temporary Internet Files ....................................................................................... 96
Mounting Accessories ......................................................................................................... 97
Outdoor Camera Installation ............................................................................................... 98
Wall Mount Junction Box ................................................................................................ 98
Pole Mount Junction Box .............................................................................................. 102
Contacting DVTEL ..................................................................................................................... 106
ii
Page 4
Table of Contents
List of Figures
Figure 1: ioi HD Analytic Bullet IP Camera .............................................................................................. 1
Figure 2: Package Contents..................................................................................................................... 2
Figure 3: CB-5222 Dimensions (Front View) ........................................................................................... 3
Figure 4: CB-5222 Dimensions (Side View) ............................................................................................ 3
Figure 5: CB-5222 Camera Input/Output Connections ............................................................................ 4
Figure 6: Camera Cables ......................................................................................................................... 7
Figure 7: System Cable ............................................................................................................................ 7
Figure 8: System Cable Hose and Wiring ................................................................................................ 7
Figure 9: Discovered IP Devices ............................................................................................................ 12
Figure 10: Assign IP Dialog Box ............................................................................................................ 12
Figure 11: Login Window ....................................................................................................................... 17
Figure 12: DVPlayer Add-On Message .................................................................................................. 17
Figure 13: Installing the ActiveX Component ......................................................................................... 18
Figure 14: Render.cab Download Dialog Box ........................................................................................ 18
Figure 15: Live Screen ........................................................................................................................... 18
Figure 16: Mounting Bracket .................................................................................................................. 19
Figure 17: Rotating the Camera ............................................................................................................. 19
Figure 18: ioi HD Web Interface with Callouts ....................................................................................... 20
Figure 19: View Mode Function Buttons ................................................................................................ 22
Figure 20: System Screen ...................................................................................................................... 25
Figure 21: Security > User Screen ......................................................................................................... 26
Figure 22: Editing Password and Privileges .......................................................................................... 27
Figure 23: IP Filter Screen ..................................................................................................................... 28
Figure 24: IEEE 802.1X/EAP-TLS Screen ............................................................................................. 29
Figure 25: Network > Basic Screen ....................................................................................................... 30
Figure 26: QoS Screen .......................................................................................................................... 32
Figure 27: SNMP Settings Screen ......................................................................................................... 33
Figure 28: UPnP Screen ........................................................................................................................ 34
Figure 29: Direct Access to Camera with UPnP Enabled ...................................................................... 35
Figure 30: DDNS Screen ....................................................................................................................... 35
Figure 31: Mail Screen – SMTP ............................................................................................................. 36
Figure 32: FTP Screen ........................................................................................................................... 37
Figure 33: Events Setup > IO Screen .................................................................................................... 38
Figure 34: Triggered Action – Upload Image by FTP ............................................................................ 39
Figure 35: Triggered Action – Upload Image by E-Mail ......................................................................... 40
Figure 36: Events Setup > Network Failure Detection Screen .............................................................. 41
Figure 37: Schedule Screen................................................................................................................... 42
Figure 38: File Location Screen ............................................................................................................. 43
Figure 39: System Log Screen .............................................................................................................. 43
Figure 40: View Information > User Information Screen ........................................................................ 44
Figure 41: View Information > User Information – Get User Privacy Screen ........................................ 44
Figure 42: Factory Default Screen ......................................................................................................... 45
Figure 43: Software Version Screen ...................................................................................................... 45
Figure 44: Software Upgrade Screen .................................................................................................... 46
Figure 45: File Type Drop-Down List ..................................................................................................... 46
Figure 46: Parameters Screen ............................................................................................................... 47
Figure 47: Import/Export Screen ............................................................................................................ 47
Figure 48: Configuration File Information Bar ........................................................................................ 48
Figure 49: Streaming > Video Format Screen ....................................................................................... 48
Figure 50: Streaming > Video Compression Screen ............................................................................. 50
Figure 51: Streaming > Video OCX Protocol Screen............................................................................. 51
Figure 52: Streaming > Video Frame Rate Screen ................................................................................ 51
Figure 53: Audio Screen ........................................................................................................................ 52
Figure 54: Exposure Screen with Shutter WDR On ............................................................................... 53
Figure 55: Multiple Shutter RSS Exposure Screen ................................................................................ 55
Figure 56: Exposure Screen with Shutter WDR Off ............................................................................... 55
Figure 57: Manual Exposure Mode with Shutter WDR Off .................................................................... 58
Figure 58: Picture Adjustment Screen ................................................................................................... 58
Figure 59: Advanced Picture Settings Screen with WDR On ................................................................ 59
iii
Page 5
CB-5222 User and Installation Guide
Figure 60: Advanced Picture Settings Screen with WDR Off ................................................................ 60
Figure 61: IR Function Screen ............................................................................................................... 61
Figure 62: Misc. Screen ......................................................................................................................... 61
Figure 63: Shutter WDR On ................................................................................................................... 62
Figure 64: Shutter WDR Off ................................................................................................................... 62
Figure 65: Analytics > Manual Depth Screen ........................................................................................ 63
Figure 66: Auto Depth Screen - Auto Calibration .................................................................................. 64
Figure 67: Horizon Line .......................................................................................................................... 65
Figure 68: Analytics > Depth > Solo Setup Instructions ........................................................................ 67
Figure 69: Analytics > Depth Control Panel ........................................................................................... 69
Figure 70: Analytics > Depth > Step 1: Ground & Height Screen .......................................................... 70
Figure 71: Analytics > Depth > Step 1: Ground & Height Instructions ................................................... 70
Figure 72: Analytics > Depth > Step 2: Camera & Horizon Screen ....................................................... 71
Figure 73: Analytics > Depth > Step 2: Camera & Horizon Instructions ................................................ 71
Figure 74: Analytics > Depth > Step 3: Advanced Depth Regions Screen ............................................ 72
Figure 75: Analytics > Depth > Step 3: Advanced Depth Regions Instructions ..................................... 72
Figure 76: Analytics > Depth > Step 4: Verification Screen ................................................................... 73
Figure 77: Analytics > Depth > Step 4: Verification Instructions ............................................................ 74
Figure 78: Analytics > Rules Screen ...................................................................................................... 74
Figure 79: Rules Drop-down List ........................................................................................................... 75
Figure 80: Analytics > Rules > Basic Attributes Tab .............................................................................. 75
Figure 81: Analytics > Rules > Advanced Attributes Tab ...................................................................... 76
Figure 82: Analytics > Responses Screen ............................................................................................. 77
Figure 83: Responses > Triggering Event Tab ...................................................................................... 77
Figure 84: Responses > Actions Tab ..................................................................................................... 78
Figure 85: Responses > Actions Table .................................................................................................. 80
Figure 86: Responses > Schedule Tab ................................................................................................. 80
Figure 87: Sched. Actions > Actions Tab ............................................................................................... 81
Figure 88: Responses > Actions Table .................................................................................................. 82
Figure 89: Sched. Actions > Schedule Tab ........................................................................................... 83
Figure 90: Analytics > On Screen Display Screen ................................................................................. 84
Figure 91: Analytics > Firmware Screen ................................................................................................ 85
Figure 92: Analytics > Backup & Restore Screen .................................................................................. 86
Figure 93: Logout Message ................................................................................................................... 86
Figure 94: Command Bar Toolbar – Select Internet Options ................................................................. 91
Figure 95: Internet Options Screen ........................................................................................................ 91
Figure 96: Command Bar Toolbar – Internet Options ............................................................................ 92
Figure 97: Schedule Screen................................................................................................................... 92
iv
Page 6
Document Information
Note:
This document is intended for use by technical users who have a basic understanding of CCTV
camera/video equipment and LAN/WAN network connections.
Remarque:
Ce document est destiné aux utilisateurs techniciens qui possèdent des connaissances de base des
équipements vidéo/caméras de télésurveillance et des connexions aux réseaux LAN/WAN.
Warning:
Installation must follow safety, standards, and electrical codes as well as the laws that apply
where the units are being installed.
Avertissement:
L'installation doit respecter les consignes de sécurité, les normes et les codes électriques, ainsi que
la législation en vigueur sur le lieu d'implantation des unités.
1 Document Information
Document Scope and Purpose
The purpose of this document is to provide instructions and installation procedures for physically
connecting the ioi HD CB-5222 analytic bullet IP camera. After completing the physical installation,
additional setup and configurations may be required before video analysis and detection can
commence. For information on the unit setup and configuration, refer to the HTML Edition Units
User’s Guide.
Proprietary Rights and Non-Disclosure
This manual is delivered subject to the following restrictions and conditions:
This document contains proprietary information belonging to DVTEL, Inc. This information
is supplied solely for the purpose of assisting explicitly the licensee of the DVTEL units.
No part of this document contents may be used for any other purpose, disclosed to any
third party or reproduced by any means, electronic or mechanical, without the express
prior written permission of DVTEL, Inc.
Trademarks and Copyrights
DVTEL, the DVTEL logo, ioi, the ioi logo, ioi analytics, ioibox, ioicam, ioi HD, ioi IP, ioi Thermal, and Site
Viewer are trademarks of DVTEL, Inc. Products and trademarks mentioned herein are for
identification purposes only and may be registered trademarks of their respective companies. DVTEL,
Inc. makes no representations whatsoever about any other products or trademarks mentioned in the
manual. This manual and its contents herein are owned by DVTEL, Inc. © DVTEL, Inc. 2015. All rights
reserved.
v
Page 7
CB-5222 User and Installation Guide
Disclaimer
Users of DVTEL products accept full
responsibility for ensuring the suitability and
considering the role of the product detection
capabilities and their limitation as they apply to
their unique site requirements.
DVTEL, Inc. and its agents make no guarantees
or warranties to the suitability for the users’
intended use. DVTEL, Inc. accepts no
responsibility for improper use or incomplete
security and safety measures.
Failure in part or in whole of the installer,
owner, or user in any way to follow the
prescribed procedures or to heed WARNINGS
and CAUTIONS shall absolve DVTEL, Inc. and its
agents from any resulting liability.
Specifications and information in this guide are
subject to change without notice.
Avis de non-responsabilité
Il incombe aux utilisateurs des produits DVTEL de
vérifier que ces produits sont adaptés et d'étudier le
rôle des capacités et limites de détection du produit
appliqués aux exigences uniques de leur site.
DVTEL, Inc. et ses agents ne garantissent d'aucune
façon que les produits sont adaptés à l'usage auquel
l'utilisateur les destine. DVTEL, Inc. ne pourra être tenu
pour responsable en cas de mauvaise utilisation ou de
mise en place de mesures de sécurité insuffisantes.
Le non respect de tout ou partie des procédures
recommandées ou des messages d'AVERTISSEMENT ou
d'ATTENTION de la part de l'installateur, du
propriétaire ou de l'utilisateur dégagera DVTEL, Inc. et
ses agents de toute responsabilité en résultant.
Les spécifications et informations contenues dans ce
guide sont sujettes à modification sans préavis.
Document Conventions
WARNING and CAUTION notes are distributed
throughout this document, whenever
applicable, to alert you of potentially
hazardous situations. These may be hazards
associated with a task or a procedure you are
carrying out or are about to carry out.
The following document conventions are used
throughout this manual:
Conventions relatives au document
Les remarques AVERTISSEMENT et ATTENTION sont
réparties dans l'ensemble du document, en fonction
des besoins, afin de vous avertir des situations
potentiellement dangereuses. Il peut s'agir de risques
associés à une tâche ou à une procédure que vous
effectuez ou êtes sur le point d'effectuer.
Les conventions suivantes sont utilisées dans
l'ensemble du document:
A Warning is a precautionary message that indicates a procedure or condition where there are
potential hazards of personal injury or death.
Avertissement est un message préventif indiquant qu'une procédure ou condition présente un
risque potentiel de blessure ou de mort.
A Caution is a precautionary message that indicates a procedure or condition where there are
potential hazards of permanent damage to the equipment and or loss of data.
Attention est un message préventif indiquant qu'une procédure ou condition présente un risque
potentiel de dommages permanents pour l'équipement et/ou de perte de données.
vi
Page 8
Document Information
A Note is useful information to prevent problems, help with successful installation, or to provide
additional understanding of the products and installation.
Une Remarque est une information utile permettant d'éviter certains problèmes, d'effectuer une
installation correcte ou de mieux comprendre les produits et l'installation.
A Tip is information and best practices that are useful or provide some benefit for installation and
use of DVTEL products.
Un Conseil correspond à une information et aux bonnes pratiques utiles ou apportant un
avantage supplémentaire pour l'installation et l'utilisation des produits DVTEL.
General Cautions and Warnings
This section contains information that indicates
a procedure or condition where there are
potential hazards.
SAVE ALL SAFETY AND OPERATING
INSTRUCTIONS FOR FUTURE USE.
Although the unit is designed and
manufactured in compliance with all applicable
safety standards, certain hazards are present
during the installation of this equipment.
To help ensure safety and to help reduce risk
of injury or damage, observe the following:
Précautions et avertissements d'ordre
général
Cette section contient des informations indiquant
qu'une procédure ou condition présente des risques
potentiels.
CONSERVEZ TOUTES LES INSTRUCTIONS DE SÉCURITÉ
ET D'UTILISATION POUR POUVOIR VOUS Y RÉFÉRER
ULTÉRIEUREMENT.
Bien que l'unité soit conçue et fabriquée conformément
à toutes les normes de sécurité en vigueur, l'installation
de cet équipement présente certains risques.
Afin de garantir la sécurité et de réduire les risques de
blessure ou de dommages, veuillez respecter les
consignes suivantes:
vii
Page 9
CB-5222 User and Installation Guide
Warning:
1. The unit’s cover is an essential part of the product. Do not open or remove it.
2. Never operate the unit without the cover in place. Operating the unit without the
cover poses a risk of fire and shock hazards.
3. Do not disassemble the unit or remove screws. There are no user serviceable parts
inside the unit.
4. Only qualified trained personnel should service and repair this equipment.
5. Observe local codes and laws and ensure that installation and operation are in
accordance with fire, security and safety standards.
Avertissement:
1. Le cache de l'unité est une partie essentielle du produit. Ne les ouvrez et ne les retirez
pas.
2. N'utilisez jamais l'unité sans que le cache soit en place. L'utilisation de l'unité sans
cache présente un risque d'incendie et de choc électrique.
3. Ne démontez pas l'unité et ne retirez pas ses vis. Aucune pièce se trouvant à l'intérieur
de l'unité ne nécessite un entretien par l'utilisateur.
4. Seul un technicien formé et qualifié est autorisé à entretenir et à réparer cet
équipement.
5. Respectez les codes et réglementations locaux, et assurez-vous que l'installation et
l'utilisation sont conformes aux normes contre l'incendie et de sécurité.
Caution:
To avoid damage from overheating or unit failure, assure that there is sufficient temperature
regulation to support the unit’s requirements (cooling/heating). Operating temperature should
be kept in the range specified for the product (-40o to 50o C/-40° to 122°F for AC/DC/PoE+
operation and -10° to 50°C/14° to 122°F for PoE operation) with no more than 90% noncondensing humidity.
Attention:
Afin d'éviter tout dommage dû à une surchauffe ou toute panne de l'unité, assurez-vous que la
régulation de température est suffisante pour répondre aux exigences de l'unité
(refroidissement/chauffage). La température de fonctionnement doit être maintenue dans la
plage de température spécifiée pour le produit (-40o à 50o C/-40° à 122°F pour l'utilisation
AC/CC/PoE+ et -10° à 50°C/14° à 122°F pour l'utilisation PoE) sans condensation d'humidité
supérieur à 90%.
viii
Page 10
Electrical Safety Notice and Warnings
Warning:
1. Read the installation instructions before you connect the unit to a power source.
2. Electrical safety should always be observed. All electrical connections must be
performed by a certified electrician.
3. If the unit uses a three-wire power cord, make sure that the product is properly
grounded when in use. This is a safety feature. If the intended power outlet does not
support three prongs, one of which is a ground, contact an electrician to install the
appropriate outlet. NEVER remove or otherwise attempt to bypass the ground pin of
the power cord. Do not operate the unit in the absence of a suitably installed ground
conductor.
4. If you use an extension cord with this system, make sure that the total ampere rating on
the products plugged into the extension cord does not exceed the extension cord
ampere rating.
5. To avoid possible shock hazards or damaging the unit, assure that the positive and
negative of the power leads are properly connected to the terminal block connector
before plugging it into the unit or turning on the power source.
6. In the following situations, the electric power should be turned off immediately and
appropriate repairs, replacements or remedies should be taken if:
The power line is damaged, frayed or shows heavy wear.
The unit has been physically crushed or deformed.
The unit has been exposed to water.
The unit has been exposed to, or shows signs of damage from, fire, intense heat,
heavy smoke, fumes, or vapors.
Electrical connections of the unit become abnormally hot or generate smoke.
The unit has been dropped, damaged or shows signs of loose internal parts.
The unit does not operate properly.
Document Information
ix
Page 11
CB-5222 User and Installation Guide
Avertissement:
1. Lisez les instructions d'installation avant de brancher l'unité à une source d'alimentation
électrique.
2. Les consignes de sécurité électrique doivent toujours être respectées. Toutes les
connexions électriques doivent être effectuées par un électricien qualifié.
3. Si l'unité utilise un cordon d'alimentation à trois fils, assurez-vous que le produit est
correctement mis à la terre du produit lors de son utilisation. Ne retirez JAMAIS, et ne
tentez pas de contourner la broche de mise à la terre du cordon d'alimentation.
N'utilisez pas l'unité en l'absence d'un conducteur de mise à la terre installé
correctement.
4. Si vous utilisez une rallonge avec ce système, assurez-vous que l'ampérage total des
produits branchés sur la rallonge ne dépasse pas l'ampérage nominal de celle-ci.
5. Pour éviter tout risque de choc électrique ou d'endommager l'unité, assurez-vous que les
bornes plus et moins de l'alimentation sont correctement raccordées au connecteur du
bloc de jonction avant de le brancher sur l'unité ou d'activer la source d'alimentation.
6. Dans les situations suivantes, l'alimentation électrique doit être coupée immédiatement,
et les réparations, remplacements ou solutions suivants doivent être effectués si :
Le cordon d'alimentation ou la prise (le cas échéant) est endommagé,
effiloché ou très usé.
L'unité a subi un choc ou a été déformée.
L'unité a été exposée à de l'eau.
L'unité a été exposée à, ou montre des signes de dégâts par le feu, une
chaleur intense, une fumée épaisse, des émanations ou des vapeurs.
Les connexions électriques chauffent de façon anormale ou produisent de la
fumée.
L'unité est tombée, a été endommagée, ou certaines pièces internes semblent
détachées.
L'unité ne fonctionne pas correctement.
Minimizing EMI and RFI
When wires run for a significant distance in an
electromagnetic field, electromagnetic
interference (EMI) can occur. Strong EMI (e.g.
lightning or radio transmitters) can destroy the
units and can pose an electrical hazard by
conducting power through lines and into the
system. Poor quality or worn wiring can result
in radio frequency interference (RFI). To
minimize the effects of EMI and RFI, consult
your reseller.
Minimisation des IEM et des IRF
Lorsque des câbles parcourent une distance
importante dans un champ électromagnétique, des
interférences électromagnétiques (IEM) peuvent se
produire. D'importantes IEM (comme la foudre ou un
émetteur radio) peuvent détruire les unités et
présenter un risque électrique si elles se propagent sur
les câbles et dans le système. Des câbles de mauvaise
qualité ou usés peuvent provoquer des interférences
radioélectriques (IRF). Pour minimiser les effets des
IEM et des IRF, consultez votre revendeur.
Avis et avertissements relatifs à la sécurité électrique
x
Page 12
Document Information
Site Preparation
There are several requirements that should be properly addressed prior to installation at the site. The
following specifications are requirements for proper installation and operation of the unit:
Ambient Environment Conditions: Avoid positioning the unit near heaters or heating
system outputs. Avoid exposure to direct sunlight. Use proper maintenance to ensure that
the unit is free from dust, dirt, smoke, particles, chemicals, water or water condensation,
and exposure to EMI.
Accessibility: The location used should allow easy access to unit connections and cables.
Safety: Cables and electrical cords should be routed in a manner that prevents safety
hazards, such as from tripping, wire fraying, overheating, etc. Ensure that nothing rests on
the unit’s cables or power cords.
Ample Air Circulation: Leave enough space around the unit to allow free air circulation.
Cabling Considerations: Units should be placed in locations that are optimal for the
type of video cabling used between the unit and the cameras and external devices.
Using a cable longer than the manufacturer’s specifications for optimal video signal
may result in degradation of color and video parameters.
Physical Security: The unit provides threat detection for physical security systems. In order
to ensure that the unit cannot be disabled or tampered with, the system should be installed
with security measures regarding physical access by trusted and un-trusted parties.
Network Security: The unit transmits over IP to security personnel for video surveillance.
Proper network security measures should be in place to assure networks remain operating
and free from malicious interference. The unit is intended for installation on the backbone
of a trusted network.
Electrostatic Safeguards: The unit as well as other equipment connected to it (relay
outputs, alarm inputs, racks, carpeting, etc.) shall be properly grounded to prevent
electrostatic discharge.
The physical installation of the unit is the first phase of making the unit operational in a security plan.
The goal is to physically place the unit, connect it to other devices in the system, and to establish
network connectivity.
xi
Page 13
Page 14
Overview
Analytic relay events
Reduced false alarm rate
Increased detection distance
Unattended baggage
detection
Intrusion detection
Object removal detection
Stopped vehicle detection
Loitering detection
Camera tampering detection
Automatic depth calibration
2 Overview
The ioi HD CB-5222 bullet camera is a 2.1 megapixel, Full HD 1080p device that features built-in
video analytics. The camera includes a varifocal motorized auto-focus DC-Iris lens with True
Day/Night performance. The camera provides real-time, H.264 and MJPEG streaming video with the
highest quality image. The lightweight, weatherproof, indoor/outdoor camera is easy to install and
operate and features a compact, sophisticated and aesthetic mechanical design.
Three models are available:
CB-5222-11 − F1.4, 3-10.5mm lens
CB-5222-21 − F1.4, 7-22mm lens
CB-5222-31 − F1.6, 6-50mm lens
The ioi HD bullet camera delivers outstanding analytic peformance. It offers enhanced detection,
even of small objects from a distance, even in scenes where there are large or multiple objects and
movement in up to 80% of the frame. The system can detect sophisticated intruders and enable the
identification of people standing upright, which reduces false alarms.
The camera’s video analytics provides alarms when it automatically detects specific events, such as
region entrance, fence trespassing, tripwire crossover, which trigger an automatic notification. You
can define the events and location in the video of the image that can be detected with usercustomizable rules, positioning criteria, responses, and scheduled actions.
Figure 1: ioi HD Analytic Bullet IP Camera
Related Documentation
ioi HTML Edition Units User’s Guide
ioi HD CB-5222 Quick Installation Guide
DNA 2.1 User Manual
Features
The camera supports the following analytic functions:
1
Page 15
CB-5222 User and Installation Guide
Advanced video analytics
Superior intruder
detection
Customizable rules and actions
H.264 and MJPEG compression
HTTP streaming MPEG
Progressive scan CMOS sensor
Detection event-driven alarms
Alarm input driven events
Relay output actions on alarm
Day/Night (IR Cut Filter)
Low lux
2D/3D noise reduction
RTSP support
Digital WDR
True multi-exposure
Wide Dynamic Range
ONVIF-conformant
Built-in web application/
web server
SNMP v1/v2/v3 SNMP traps
Up to two E-mail SMTP alarms
(excluding analytic alarms)
FTP upload
(up to two addresses)
Upload alarm images to FTP
(excluding analytic alarms)
UPnP support
BNC analog video output
Security IP restricted access
allow/deny list
Multiple users
Group permissions
Per-user permissions
Built-in heater
Supports PoE/PoE+/
12VDC/ 24VAC
IP Bullet Analytic Camera
1x 4-pin connector and 1x 3-pin
connector
Quick Installation Guide
CD with bundled software
and documentation
5x Philips screws
(34 x 4mm/1.345” x 0.132”) with
plastic plugs, plus 1x Torx screw
(6.65 x 2.77mm/0.263” x 0.108”)
The camera includes the following key general features:
Package Contents
Before proceeding, check that the box contains the items listed here. If any item is missing or has
defects, do not install or operate the product. Contact your dealer for assistance.
2
Figure 2: Package Contents
Page 16
Introduction to the CB-5222 Analytic Bullet IP Camera
Note:
The camera length is 285mm (11.1 in.) with the sunshield and fully extended mounting arm.
3 Introduction to the CB-5222 Analytic Bullet IP Camera
This chapter provides the camera dimensions for reference before installation.
The chapter includes the following topics:
CB-5222 Camera Dimensions
System Cable
CB-5222 Camera Dimensions
The mechanical dimensions of the CB-5222 Analytic Bullet IP Camera are shown below.
Figure 3: CB-5222 Dimensions (Front View)
Figure 4: CB-5222 Dimensions (Side View)
3
Page 17
CB-5222 User and Installation Guide
Cable
Pin No./ Connector Type
Definition
Description
Ethernet
RJ45, Network LEDs
10/100/1000Mbps
Ethernet/PoE/PoE+
For network, Power over
Ethernet (PoE), or PoE+
connection
Audio In
3.5mm audio plug (pink)
Line in
For connecting line-level audio
input or microphone with builtin pre-amplifier
Audio Out
3.5mm audio plug (green)
Line out
For connecting headphone or
loudspeakers with built-in
amplifier
Video
BNC
Analog video
For video output
Power
1- Power (+)
2- Earth GND
3- Power (-)
12VDC/24VAC
3-terminal connection block
Alarm
DI - Input (+)
DI - Input (-)
Alarm input
4-terminal connection block
DO - Output (+)
DO - Output (-)
Alarm output
System Cable
Figure 5 shows the system cable.
Figure 5: CB-5222 Camera Input/Output Connections
The connectors, pin numbers and signal definitions related to each pin are listed below:
4
Page 18
Introduction to the CB-5222 Analytic Bullet IP Camera
Pin No.
Designation
Terminal Block
Alarm Connections
DI-
Input (-)
DI+
Input (+)
DO-
Output (-)
DO+
Output (+)
Pin
Symbol
Designation
Terminal Block
Power Connections
-
Negative
Ground
+
Positive
3.2.1 Alarm Input/Output Pin-out
The alarm input and output connections are shown below.
3.2.2 Power Input/Output Pin-out
The power input and output connections are shown below.
5
Page 19
Page 20
Introduction to the CB-5222 Analytic Bullet IP Camera
System Cable
IP66 RJ45 Cable
3.2.3 Waterproofing the Camera Cable Connectors
Follow the instructions below to waterproof the connectors for the different types of cables included
in the system cable. The cables are shown below.
Figure 6: Camera Cables
System Cable
To waterproof the system cable
1. Connect all the required devices to the system cable.
2. Coat the joints with silicone gel. There should be no gap between the connectors and the
cables. For alarm I/O connector and power connector, make sure the side with wires
attached is also sealed with silicone gel.
Figure 7: System Cable
3. Seal the end of the rubber coating of the system cable as indicated in the figure below. Use
enough silicone gel to fill in the hose and wrap around each wire in order to properly
waterproof the cable.
Figure 8: System Cable Hose and Wiring
7
Page 21
CB-5222 User and Installation Guide
A flashing green PWR LED indicates a 10/100/1000 Mbps full-duplex connection.
A steady green PWR LED indicates a 10/100/1000 Mbps half-duplex connection.
A flashing yellow LNK LED indicates the amount of network activity. The faster the
flashing, the greater the amount of data that is being transmitted.
3.2.4 Connecting the Unit to the Network
To ensure transmission quality, cable length should not exceed 100 meters (328 feet). Connect one
end of the Ethernet cable to the RJ45 connector of the system cable, and plug the other end of the
cable to the network switch or PC. Check the status of the link and the activity LEDs. If the LEDs are
unlit, check the LAN connection.
A Cat 5 Ethernet cable is recommended for network connection. For best transmission quality, the
cable length should not exceed 100 meters (328 feet). Connect one end of the Ethernet cable to the
CB-5222 camera and the other end of the cable to the network switch or PC. Check the status of the
link indicator and activity indicator LEDs. If the LEDs are unlit, check the LAN connection.
3.2.5 Connecting Power to the Camera
The camera can be powered by Power over Ethernet (PoE), PoE+, or by an external 12VDC, 24VDC,
or 24VAC adaptor (not included in the package).
If using an external power supply, connect the power leads or three-pin power terminal
block to the power supply.
If using PoE or PoE+, make sure that a Power Sourcing Equipment (PSE) device is used in the
network.
Make sure the camera’s power cable is properly connected. All electrical work must be performed in
accordance with local regulatory requirements.
For operation at -40o to 50o C/-40° to 122°F, use an AC, DC, or PoE+ power source. For operation at
-10° to 50°C/14° to 122°F, use a PoE power source.
8
Page 22
System Requirements
Item
Camera Client Application System Requirements
Personal
Computer
Intel® Pentium® M, 2.16 GHz or Intel® CoreTM2 Duo, 2.0 GHz
2GB RAM or better
Operating System
Windows 7, 8, or 8.1
Web Browser
Microsoft Internet Explorer 9, 10, 11
Network Card
10Base-T (10 Mbps), 100Base-TX (100 Mbps), or 1000Base-T (1Gbps) operation
Viewer
ActiveX control plug-in for Microsoft IE
4 System Requirements
To access the CB-5222 bullet IP camera via a web browser, ensure that your PC has the proper
network connection and meets the system requirements described below.
9
Page 23
Page 24
Installation
Setting the Camera’s
Focal Length
Initial Camera
Configuration
Camera Mounting
Instructions
Note:
Use a short focal length to cover a wide area and detect objects at close distances. Use a long
focal length to achieve greater detection distances while narrowing the Field of View.
Caution:
If you are using DVTEL Latitude, we recommend that you configure the camera’s settings via the
AdminCenter. This is because the camera’s web-based interface might be overwritten by
Latitude settings. Refer to the Latitude online help for information regarding configuring camera
settings.
Attention:
Si vous utilisez DVTel Latitude, nous vous conseillons de configurer les paramètres de la caméra
via l'AdminCenter. En effet, l'interface Internet de la caméra peut être remplacée par les
paramètres Latitude. Veuillez consulter l'aide en ligne Latitude pour de plus amples informations
sur la configuration des paramètres de la caméra.
5 Installation
Follow the instructions below for installation of the ioi HD CB-5222 camera.
Related Links
Setting the Camera’s Focal Length
Focal length determines the scene’s viewing angle, or, in other words, the dimensions of the scene which
will be generated by the camera. The trade-off for focal length is between the width of the scene and the
magnification of objects appearing in the scene. The longer the focal length is, a narrower scene will be
achieved, while the size of objects will increase. Greater size means that more pixels will be used to
represent each object, and greater level of details will be present.
In a similar manner, the shorter the focal length is, the smaller the size of each object will be, while the
captured scene will become wider.
After you select your lenses and see the amount of detail provided, consider your security
surveillance coverage, camera locations, and any additional needs that may be discovered. Consult
your DVTEL representative if you have any questions.
Initial Camera Configuration
To perform the initial camera configuration
Unpack the camera and remove the protective cover.
Remove the PE cloth sheet and lens cap.
Connect one end of the Cat 5 Ethernet cable to the Ethernet port of the camera and the
RJ45 connector at other end to the Power Sourcing Equipment (PSE) device, such as a
PoE or PoE+ switch.
Verify that the RJ45 connector LEDs illuminate flashing green (indicating proper
operation) and flashing yellow (indicating network activity).
11
Page 25
CB-5222 User and Installation Guide
Note:
DNA is a user-friendly utility that is designed to easily discover and configure DVTEL
edge devices on a network. The ioi HD bullet camera is supported by DNA version
2.0.4.8 and above. For instructions how to use DNA, download the DNA User
Manual from the Downloads tab at http://www.dvtel.com/products-
solutions/tools/.
Note:
The camera default IP Address and the subnet mask IP Address are automatically
supplied by the DHCP server.
Copy and run the dna.exe file from the included CD.
Mark the unit requiring IP assignment.
Figure 9: Discovered IP Devices
Right-click on the mouse and select the assigned IP or press the Assign IP button to
open the DNA Assign IP screen.
In the dialog box that is displayed, enter values for the IP Address, Gateway and
Netmask.
Click Update and wait for OK status to be displayed.
Figure 10: Assign IP Dialog Box
Disconnect the Ethernet cable. The camera is ready for deployment (mounting) in a site
installation.
12
Page 26
Installation
Tip:
A camera setup adapter, such as Veracity Pinpoint, can be used to connect a laptop
directly to the camera when using PoE.
Caution:
To avoid damage from overheating or unit failure, assure that there is sufficient
temperature regulation to support the unit’s requirements (cooling/heating). Operating
temperature should be kept in the range specified for the product with no more than
90% relative humidity, non-condensing.
Attention:
Afin d'éviter tout dommage dû à une surchauffe ou toute panne de l'unité, assurez-vous
que la régulation de température est suffisante pour répondre aux exigences de l'unité
(refroidissement/chauffage). La température de fonctionnement doit être maintenue
dans la plage de température spécifiée pour le produit sans condensation d'humidité
supérieur à 90%.
Camera Mounting Instructions
Read the instructions provided in this chapter thoroughly before installing the CB-5222 camera. The
following points are additional considerations:
There must be a fuse or circuit breaker at the starting point of the electrical wiring
infrastructure.
For indoor installations, such as industrial applications, the CB-5222 camera must be
protected from hostile external elements (e.g., corrosive environment, metallic dust,
extreme temperatures, soot, moisture, over spray, etc.)
Do not place the CB-5222 camera on or near radiators and heat sources.
All electrical work must be performed in accordance with local regulatory requirements.
To mount the camera
Screw the camera’s mounting base into the ceiling/wall/flat surface.
Set the camera in a fixed position for the Field of View required.
Connect the cables and wiring to the camera. See Figure 5: CB-5222 Camera
Input/Output Connections.
13
Page 27
Page 28
Using the DNA Utility to Search and Access the Camera
Note:
The ioi HD bullet camera is supported by DNA version 2.1 and above. For detailed guidelines
about DNA and its usage, refer to the DNA 2.1 User Manual, which is included in the CD
provided with the camera. You can also download the manual from the Downloads tab at
http://www.dvtel.com/products-solutions/tools/.
6 Using the DNA Utility to Search and Access the Camera
The DVTEL Network Assistant (DNA) is a user-friendly utility that is designed to easily discover and
configure DVTEL edge devices on a network. The DNA tool has a simple user interface and does not
require any installation. The software is provided as a single, standalone executable. It runs on any
PC.
DNA provides a central location for listing all the DVTEL camera models accessible over the network.
Once listed, each camera can be right-clicked to access and change the network settings. If the
network settings are changed for some reason, a new search will relist the units. The units may then
be configured via the web interface.
If the camera is managed by DVTEL’s Horizon or Meridian NVR and is configured as a DHCP server,
Horizon or Meridian automatically assigns the camera an IP address. Configure the camera with
DHCP-enabled.
If DVTEL Latitude is being used, configure the unit with a static IP address rather than with DHCP.
This ensures that the IP address will not automatically change in the future and interfere with
configurations and communication. The camera must be made accessible for the network’s
addressing.
15
Page 29
Page 30
Using the Web Browser to Access the Camera
Note:
Users who have previously installed the DVPlayer application on the PC should delete the
existing DVPlayer from the PC before accessing the camera. For information on how to uninstall
and clear temporary Internet files, see Deleting the Existing DVPlayer (page 95).
Note:
1. The user name and password are case-sensitive.
2. For security purposes, it is recommended to change the user name and
password.
3. If the password is changed and DVTEL Latitude AdminCenter Discovery feature is
in use, deselect all other proprietary types. Select IOimage as the Unit Type so
that the new password can be configured in the Latitude Discovery tab settings.
7 Using the Web Browser to Access the Camera
The DVTEL DVPlayer web player software is used for accessing the camera, configuring its properties, and
viewing video through your web browser.
To install the DVPlayer software online
Open your web browser and type the camera’s IP address. The unit’s Login Window opens.
Figure 11: Login Window
Enter the default user name (“admin”) and password (“admin”).
Upon initial connection to the camera, a prompt to install the DVPlayer application appears.
Click Allow.
Figure 12: DVPlayer Add-On Message
17
Page 31
CB-5222 User and Installation Guide
Do one of the following:
If the web browser does not allow DVTEL Web Player to install, check the Internet
security settings or ActiveX controls and plug-in settings to continue the process. See
Internet Security Settings.
If the ActiveX installation message is displayed:
Click the Click here link to install the ActiveX component.
A dialog box opens, requesting you to install the render.cab file.
Figure 13: Installing the ActiveX Component
Figure 14: Render.cab Download Dialog Box
Click Install. The application closes and reopens on the Live screen.
Figure 15: Live Screen
If the video is not displayed, the DVPlayer Add-On Message is displayed (see Figure 12).
Click the Click here link. The video is displayed in the Live screen.
18
Page 32
Adjusting and Framing-Up the Camera View
Tip:
To view greater image detail for more accurate high-definition focusing, on the
web interface Home page, click the Full Screen button and use the full
screen view to check the focus.
8 Adjusting and Framing-Up the Camera View
After the camera is connected to the network and is running, it is necessary to frame-up the scene
and adjust the camera settings to optimize the picture for the individual scenes. If Latitude is being
used, consider scheduling different settings for changing ambient conditions throughout the day,
week, month or seasons.
To adjust and frame-up the camera view
From the unit’s Camera > Exposure screen, do one of the following:
If you selected Shutter WDR On from the Camera > Misc. screen, select the default
mode (WDR Multiple Shutter).
If you selected Shutter WDR Off from the Camera > Misc.screen, select the default
mode (Auto Shutter).
Save changes and complete the focusing steps.
Adjust the pan and tilt:
Loosen the tension screw on the mounting bracket.
Figure 16: Mounting Bracket
Rotate (pan and tilt) the camera so that the Field of View is optimized for your
scene.
Figure 17: Rotating the Camera
Tighten the tension screw to hold the camera in place.
When finished, set your exposure settings as needed.
19
Page 33
CB-5222 User and Installation Guide
9 Configuration and Operation
The ioi HD camera is provided with a browser-based configuration interface for video playback and
recording. If DVTEL’s Latitude VMS is used, many of the configurations and features of DVTEL’s VMS
provide additional configuration and automation options for the camera.
This section includes the following information:
CB-5222 Web Interface
Live Screen
Settings Screens
Log Out
CB-5222 Web Interface
The figure below explains the ioi HD camera’s web-based user interface.
Figure 18: ioi HD Web Interface with Callouts
20
Page 34
Configuration and Operation
The user interface displays the following information:
1. The Navigation Bar is displayed in the center of the screen containing Live and Settings
buttons.
Live Button
The Live screen opens by default when the camera logs on. It is used to monitor live
video of the targeted area, adjust the display size, take snapshots of the view area,
stop/start video streaming, record video in a designated file location, activate or deactivate a loudspeaker (audio function). An explanation of the items on the screen is
included below.
Settings Button
Clicking the Settings button opens the Settings screen, whose sidebar which includes
three tabs − System, Streaming, and Camera − that are used for to configure system
settings.
System Settings
The administrator can configure settings for basic system parameters, security,
network operation, events, recording, storage, system maintenance, and more.
Details are discussed in System Settings.
Streaming Settings
The administrator can modify video and audio settings on this page. Details are
discussed in Streaming Settings.
Camera Settings
The administrator can adjust many of the camera settings on this page, such as
Exposure, Picture Adjustment, IR Function, and TV System. Details are discussed
in Camera Settings.
Analytics
The Analytics tab is used for configuring video analytics settings for depth, rules,
responses, scheduled actions, on-screen display, firmware, and backup & restore.
Details are discussed in Analytics.
2. The Language Bar is displayed to the right of the Navigation Bar. Supported languages
include English, German, Spanish, Italian, Japanese, Korean, Portuguese, Russian, Simplified
Chinese, and Traditional Chinese. The Analytics screens support only English, Spanish,
Japanese, Russian, and Traditional Chinese
3. The Log out link is located to the right of the Language Bar. Click the Log Out link to exit the
application or log into the camera with a different username and password. See Log Out.
4. The camera model number is displayed under the Log out link.
5. The current date and time are displayed under the model number.
6. The video format is displayed to the left of the date and time.
7. Function buttons are displayed to the left of the Live View window. These are discussed in
the following section. In the center of the interface is the Live View window, which displays
the image that the camera is monitoring.
8. The Live View window in the center of the interface displays the monitored scene.
9. The camera’s firmware version is displayed under the Live View window on the right side.
10. The Arm/Disarm button is displayed under the Live View window. Click Arm to start the
analytics engine. Click Disarm to stop the analytics engine.
21
Page 35
CB-5222 User and Installation Guide
Full-Window Display
Full-Screen Mode
Snapshot
Note:
When using Windows 8 OS, the storage location cannot be C:\. You must define a storage
location that does not require Administrator privileges on the PC.
Record/Pause
Half-Window Display
11. The Clear Alarms button is displayed under the Arm/Disarm button. Click Clear Alarms to
stop the alarms and return analytics to their initial stage.Live Screen
The camera’s Live screen is used to monitor live video (see Figure 15: Live Screen). The View Mode
pane in the Live screen includes the following function buttons:
Figure 19: View Mode Function Buttons
Click this button to view the live video in the full Live Video window.
Click this button to view the live video in half of the Live View window.
Click this button to view the live video on the full screen of your monitor. Click the ESC (Escape) key
on your keyboard to exit Full-Screen Mode.
Click this button to automatically save the JPEG snapshots in the specified location. The default
location to save snapshots is: C:\.To change the storage location, refer to File Location.
Pressing the Recording button stores recordings from the Live View in the location specified on the
local hard drive, which can be configured in the File Location screen. The default storage location for
the web recording is: C:\. Refer to File Location for details.
22
Page 36
Configuration and Operation
Note:
When using Windows 8 OS, the storage location cannot be C:\. You must define a storage
location that does not require Administrator privileges on the PC.
Video Streaming Restart/Stop
Mic
Speaker
Zoom: Wide/Tele
Note:
Changing zoom settings will delete the analytic settings.
Zoom Reset
Note:
Changing zoom settings will delete the analytic settings.
Step: Wide/Tele
Note:
Changing zoom settings will delete the analytic settings.
Step Range
Focus: Near/Far
Press the Stop button to disable video streaming and to display the live video as black. Press Restart
to show the live video again.
The Microphone button allows the local site to talk to the remote site. Click the button to switch it
on/off. This function is available only to a user who has been granted this privilege by the
Administrator. Refer to User in the Security section for further details.
Click the Speaker button to mute/activate the audio. This function is available only to a user who has
been granted this privilege by the Administrator. Refer to User in the Security section for further
details.
Press the Tele or Wide button to implement continuous zoom adjustment.
Press the Reset button to calibrate the camera lens at full wide end.
Press the Wide Step or Tele Step button to alternate the zoom between wide and telephoto views
within a user-defined range of steps, which can be selected from the drop-down list shown below.
Select from a user-defined range of up to 128 steps from the drop-down list.
Press the Near or Far button to implement continuous focus adjustment.
23
Page 37
CB-5222 User and Installation Guide
Focus Reset
Step: Near/Far
Step Range
AF: Manual
AF: Zoom
AF: Push
System
Security
Network
Events Setup
Schedule
File Location
Maintenance
Import/Export
Note:
The System screen is accessible only by the Administrator.
Press the Reset button to calibrate the camera lens at infinity focus.
Press the Near Step or Far Step button to alternate the focus between near and far views.
Select from a user-defined range of up to 128 steps from the drop-down list.
Click the Manual button to manually change the focus.
Click the Zoom button so that the focus will be adjusted automatically after changing zoom.
Click the Push button once to adjust zoom or focus. In this mode, the camera starts the focusing
process automatically and stops after it receives a focused image.
Settings
The Settings tab in the Navigation Bar opens the sections in the sidebar that are used for configuring
the camera. Four sections are available for configuration: System, Streaming, Camera, and Analytics.
9.2.1 System Settings
The System section in the sidebar includes the following tabs:
24
Page 38
Configuration and Operation
System Screen
The System screen is used for entering the camera’s friendly name and date and time settings.
Figure 20: System Screen
Host Name
The host name is for camera identification. If the alarm function is enabled and is set to send an
alarm message by Mail or FTP, the host name entered here is displayed in the alarm message. See
Events Setup.
Time Zone
Select the time zone from the drop-down list.
Enable Daylight Saving Time
To enable daylight saving time, check the Enable daylight saving time box. Then specify time offset
(number of hours or minutes difference between daylight saving time and standard time). The
format for time offset is [hh:mm:ss]. For example, if the amount of time offset is one hour, enter
01:00:00 in the field. Finally, enter the start time for daylight saving time and end time for daylight
saving time.
Time format
Enables a choice of formats: either year, month, and day (yyyy/mm/dd); day, month, and year
(dd/mm/yyyy); or month, day, and year (mm/dd/yyyy).
Sync with Computer Time
Select this button to synchronize the camera’s date and time display with the PC. You can change
the PC date and time in the respective text box.
25
Page 39
CB-5222 User and Installation Guide
User
IP Filter
IEEE 802.1X
Note:
The following characters are valid: A-Z, a-z, 0-9,!#$%&’-.@^_~.
Manual
The Administrator can set the camera’s date and time manually. Entry format should be identical
with that displayed to the right of the text box.
Sync with NTP Server
Network Time Protocol (NTP) is an alternate way to synchronize the camera’s clock with an NTP
server. Select Sync with NTP Server. In the NTP server text box, enter the network time server host
name or IP address to synchronize. Then, from the Update interval drop-down list, select an update
interval (every hour, day or week). For further information about NTP, visit www.ntp.org.
Click SAVE when finished.
Security
The Security section in the sidebar includes the following tabs:
9.2.1.2.1 User
The User screen is used for entering and managing user credentials and privileges, as well as
configuring authentication settings.
Figure 21: Security > User Screen
Admin Password
Change the administrator’s password by entering the new password in both text boxes. The input
characters/numbers are displayed as dots for security purposes. After clicking SAVE, the web
browser asks the Administrator for the new password (maximum 14 digits).
26
Page 40
Configuration and Operation
Note:
You must enter the user password and also select the authorized function(s). When
finished, click SAVE to modify the account authority.
Add user
The user name and passwords are limited to 14 characters. There is a maximum of 20 user accounts.
To add a new user
In the Add User section, enter the new user name and password in the respective fields.
Select the appropriate check boxes to give the user I/O Access, Camera Control, Talk,
Listen, or Analytics permissions.
I/O access – Basic functions that enable the user to view video when accessing the
camera.
Camera control – Allows the user to change camera parameters on the Camera tab.
Talk – Allows the user at the local site to talk to the administrator at the remote site.
Listen – Allows the user at the local site to listen to the administrator at the remote
site.
Analytics – Allows the user to define analytic parameters from the Analytics tab.
Click ADD.
Manage User
To delete a user, pull down the user list and select the user name to delete. Click DELETE to
remove it.
To edit a user, pull the user list down and select a user name. Click EDIT to edit the user’s
password and privileges.
Figure 22: Editing Password and Privileges
Streaming Authentication Setting
From the drop-down list, select one of the following options:
Disable – Do not use streaming authentication (default setting).
Basic – A form of authentication that uses unencrypted base64 encoding. Basic
Authentication should generally only be used where transport layer security is provided.
Digest – A form of authentication used over RTSP in which credentials are encrypted when
transmitted.
27
Page 41
CB-5222 User and Installation Guide
9.2.1.2.2 IP Filter
The IP Filter screen is used for restricting access to the camera by denying/allowing specific IP
addresses.
To enable the IP filter
Check the box to enable the IP Filter function. Once enabled, the listed IP addresses
(IPv4) are allowed/denied access to the camera.
Select Allow or Deny from the drop-down list.
Click the APPLY button to determine the IP Filter behavior.
To add or delete an IP address
Enter the IP address in the Filtered IP Addresses text box.
Click ADD to add a new filtered address. The Filtered IP Addresses box shows the
currently configured IP addresses. Up to 256 IP address entries may be specified.
To remove an IP address from the list, select the IP address and then click DELETE.
Figure 23: IP Filter Screen
28
Page 42
Configuration and Operation
9.2.1.2.3 IEEE 802.1X
The IEEE 802.1X screen is used for enabling the camera to access a network protected by
802.1X/EAPOL (Extensible Authentication Protocol over LAN). Users must contact the network
administrator to obtain certificates, user IDs, and passwords.
Figure 24: IEEE 802.1X/EAP-TLS Screen
CA Certificate
The CA certificate is created by the Certificate Authority for the purpose of validating itself. Click
Browse to locate the certificate. Then click UPLOAD to check the server’s identity.
Client Certificate/Private Key
Click Browse to locate the Client Certificate and Private Key. Then click UPLOAD to upload the Client
Certificate and Private Key to authenticate the camera.
Settings
Identity – Enter the user identity associated with the certificate. Up to 16 characters can be
used.
Private Key Password – Enter the password associated with the user identity. Up to 16
characters can be used.
Enable IEEE 802.1X
Check the box to enable IEEE 802.1X. The setting is disabled by default. Click SAVE to save the IEEE
802.1X/EAPTLS setting.
29
Page 43
CB-5222 User and Installation Guide
Basic
QoS
SNMP
UPnP
DDNS
Mail
FTP
Network
The Network section on the sidebar includes the following tabs:
9.2.1.3.1 Basic
The Basic screen is used for configuring general and advanced network settings. You can connect to
the camera with either fixed or dynamic (DHCP) IP address. The camera also provides PPPoE (Pointto-Point Protocol over Ethernet) support for users who connect to the network via PPPoE.
The screen is divided into two sections: General and Advanced.
30
Figure 25: Network > Basic Screen
Page 44
Configuration and Operation
Note:
For future reference, record the camera’s MAC address, which is found on the camera
label.
Note:
If you change the default HTTP port number and are using Latitude, you must rediscover
the unit.
Select one of the following options in the General area for configuring network settings:
Get IP address automatically (DHCP)
If you select Get IP address automatically, you can use the DNA utility, which is provided in
the supplied CD, to obtain the IP address. See Using the DNA Utility to Search and Access the
Camera.
Use fixed IP address
The camera’s default setting is Use fixed IP address. You may use DNA or enter the IP
address in your browser’s URL address bar.
To set up a new static IP address
Select the Use fixed IP address option.
Enter the following information:
IP address – The IP address is necessary for network identification.
Subnet mask – Used to determine if the destination is in the same subnet. The default
value is 255.255.255.0.
Default gateway – Used to forward frames to destinations in a different subnet. An
invalid gateway setting causes transmission to destinations in other subnets to fail.
Primary DNS – The primary domain name server that translates host names into IP
addresses.
Secondary DNS – A secondary domain name server that backs up the primary DNS.
Use PPPoE – If you are using PPPoE, enter the PPPoE user name and password in the
respective fields.
Click SAVE to confirm the settings.
Enter the following advanced parameters in the Advanced section of the screen:
Enable Gigabit Ethernet – Select the checkbox to enable a 1Gbps network connection. By
default, network negotiation is limited to maximum 100 Mbps and the checkbox is disabled.
Web Server port – The default web server port is 80. Once the port is changed, the user must
be notified the change for the connection to be successful. For instance, when the
Administrator changes the HTTP port of the camera whose IP address is 192.168.0.100 from
80 to 8080, the user must type in the web browser http://192.168.0.100:8080 instead of
http://192.168.0.100.
31
Page 45
CB-5222 User and Installation Guide
Note:
Be sure to assign a different port number for each separate service mentioned above.
Note:
To enable this function, make sure the switches/routers in the network support QoS.
RTSP port – The default setting of the RTSP port is 554. The range is from 1024 to 65535.
MJPEG over HTTP port – The default setting of MJPEG over HTTP port is 8008. The range is
from 1024 to 65535.
MTU – The MTU (Maximum Transmission Unit) is the greatest amount of data that can be
transferred in one physical frame on the network. For Ethernet, the MTU is 1500 bytes
(default setting). For PPPoE, the MTU is 1492. The range is from 700 to 1500 bytes.
Click SAVE to save the settings.
9.2.1.3.2 QOS
The QoS (Quality of Service) screen enables you to configure differentiated service levels for
different types of traffic packets and to guarantee delivery of priority services during periods of
network congestion. Adapting the Differentiated Services (DiffServ) model, traffic flows are classified
and marked with DSCP (DiffServ Code point) values, and as a result receive the corresponding
forwarding treatment from DiffServ-capable routers.
Figure 26: QoS Screen
DSCP Settings
The DSCP value range is from 0 to 63. The default DSCP value is 0 (DSCP disabled). The camera uses
the following QoS classes: Video, Audio, and Management.
Video DSCP – This class consists of applications such as MJPEG over HTTP, RTP/RTSP and
RTSP/HTTP.
Audio DSCP – The cameras support audio.
Management DSCP – This class consists of HTTP traffic (web browsing).
Click SAVE when complete.
32
Page 46
Configuration and Operation
9.2.1.3.3 SNMP
The SNMP (Simple Network Management Protocol) screen enables the camera to be monitored and
managed remotely by the network management system.
Figure 27: SNMP Settings Screen
SNMP v1/v2
Enable SNMP v1 or Enable SNMP v2 – Select the version of SNMP (v1 or v2) to use by
checking the relevant box.
Read Community – Specify the community name that has read-only access to all supported
SNMP objects. The default value is public.
Write Community – Specify the community name that has read/write access to all supported
SNMP objects (except read-only objects). The default value is private.
SNMP v3
SNMPv3 provides important security features including:
Confidentiality – Encryption of packets to prevent snooping by an unauthorized source.
Integrity – Message integrity to ensure that a packet has not been tampered with in transit
including an optional packet replay protection mechanism.
Authentication – To verify that the message is from a valid source.
33
Page 47
CB-5222 User and Installation Guide
Note:
You may have to consult with your System Administrator to activate this function.
To enable the SNMP v3 protocol, enter the appropriate data and passwords requested:
Enable SNMP v3 – Select the checkbox.
Security Name – See note below.
Authentication Type – Select MD5 or SHA from the drop-down list. See note below.
Authentication Password – See note below.
Encryption Type – Select DES or AES from the drop-down list. See note below.
Encryption Password – See note below.
Traps for SNMP v1/v2/v3
Traps are used by the camera to send messages to a management system for important events or
status changes. Configure the following settings as required:
Enable traps – Check this box to activate trap reporting.
Trap address – Enter the IP address of the management server.
Trap community – Enter the community to use when sending a trap message to the
management system. The default value is public.
Warm start – Select this checkbox if you want the camera to perform a software reload
(warm start SNMP trap).
Click SAVE when complete.
9.2.1.3.4 UPnP
The UPnP screen enables the Universal Plug-and-Play protocol on your network devices.
Figure 28: UPnP Screen
34
Page 48
Configuration and Operation
Note:
To enable this function, make sure the UPnP component is installed on your computer.
Refer to Install UPnP Components for the Windows 7, Windows 8, and Windows 8.1
procedure.
Note:
To enable this function, ensure that your router supports UPnP and is activated.
UPnP Setting
Enable UPnP – This is the default setting. If UPnP is enabled and a camera is discovered on
the LAN, the icon of the connected camera appears in My Network Places, allowing direct
access, as seen below.
Figure 29: Direct Access to Camera with UPnP Enabled
Enable UPnP port forwarding – When UPnP port forwarding is enabled, the camera is
allowed to open the web server port on the router automatically.
Friendly name – Set the name for the camera for identification.
Click SAVE to save the settings.
9.2.1.3.5 DDNS
The DDNS (Dynamic Domain Name System) screen allows a host name to be constantly synchronized
with a dynamic IP address. This permits those using a dynamic IP address to be accessed by a static
domain name. DDNS is not enabled by default.
Figure 30: DDNS Screen
35
Page 49
CB-5222 User and Installation Guide
Enable DDNS
Check this box to enable DDNS.
Provider – Select a DDNS host provider name from the drop-down list:
DynDNS.org (Dynamic)
DynDNS.org (Custom)
No-IP
ChangeIP
Host name – Enter the registered domain name in the field.
Username/E-mail – Enter the username or e-mail address required by the DDNS provider for
authentication.
Password/Key – Enter the password or key required by the DDNS provider for
authentication.
Click SAVE to save the setting.
9.2.1.3.6 Mail
The Mail screen is used for configuring Simple Mail Transfer Protocol (SMTP) settings. SMTP is a
protocol for sending e-mail messages between servers. It is a relatively simple, text-based protocol,
where one or more recipients of a message are specified and the message text is transferred.
The following screen shows the SMTP configuration.
Figure 31: Mail Screen – SMTP
The Administrator can send an e-mail via Simple Mail Transfer Protocol (SMTP) when an alarm is
triggered. Two SMTP server accounts can be configured. Enter the settings for the 1st SMTP server
and 2nd SMTP server in the appropriate fields. Settings include SMTP server, server port (default port
is 25), account name, password, and recipient e-mail address settings. For SMTP server details,
contact your network service provider.
36
Page 50
Configuration and Operation
To use SSL encryption of the email, select the 1st SMTP SSL or 2nd SMTP SSL checkbox for the
respective server.
Enter the sender’s email address in the text box.
Click SAVE when finished.
9.2.1.3.7 FTP
The Administrator can send an alarm message to one or two File Transfer Protocol (FTP) sites when
motion is detected. The following screen shows the FTP settings.
Figure 32: FTP Screen
For each server, enter the server IP address, server port number, user name, password, and remote
folder path.
To use passive mode, select the 1st FTP passive mode or 2nd FTP passive mode checkbox for the
respective server. In passive mode, FTP the client initiates both connections to the server, solving
the problem of firewalls filtering the incoming data port connection to the client from the server.
In order to support passive mode FTP on the server-side firewall, the following communication
channels must be opened:
FTP server's port 21 from anywhere (client initiates connection)
FTP server's port 21 to ports > 1023 (server responds to client's control port)
FTP server's ports > 1023 from anywhere (client initiates data connection to random port
specified by server)
FTP server's ports > 1023 to remote ports > 1023 (server sends ACKs and data to client's data
port)
To test the connection to the specified FTP server, click TEST for the first or second server.
Click SAVE when finished.
37
Page 51
CB-5222 User and Installation Guide
Note:
Actions related to an analytic event that is defined in the Analytics > Responses screen are not
affected by the status of the alarm switch.
Events Setup
The Events Setup section on the sidebar includes the following tabs: IO and Network Failure
Detection.
9.2.1.4.1 IO
The IO screen enables control over the input and output alarms, which are generated if an event is
recognized by the system.
Figure 33: Events Setup > IO Screen
Alarm Switch
The Administrator can select from the following options:
Select Off to disable an alarm.
Select On to enable an alarm (default setting).
Select By schedule to set a schedule. Then click Please Select to select up to 10 schedules
from the drop-down list that opens. The selected schedules are displayed in the Please
Select text box. To set a schedule, open the Schedule tab.
Click Save after configuring the settings.
Alarm Type
Select an alarm type (Normal close or Normal open) that corresponds to the alarm application.
Normal open is the default setting. Click SAVE after configuring the settings.
38
Page 52
Configuration and Operation
Note:
This option is valid only when using MJPEG as the camera stream.
Note:
Make sure that FTP configuration has been completed. See FTP for details.
Alarm Output
Define the normal alarm output signal as Normal close or Normal open, according to the current
alarm application. Normal open is the default setting. Click SAVE after configuring the settings.
Triggered Action
The Administrator can specify various alarm actions to take when an alarm is triggered. The
following options are available:
When an alarm is triggered, event images are uploaded to the designated FTP site. Follow these
steps:
From the FTP address drop-down list, select one of the two FTP addresses to use.
From the Pre-trigger buffer and Post-trigger buffer drop-down lists, select the
number of frames for the buffer from 1-20 frames.
Figure 34: Triggered Action – Upload Image by FTP
Select the Continue image upload checkbox to upload an image by FTP for a defined
period of time or while the trigger is active. Select one of the following options:
To specify the length of time for the upload, select Upload for and enter the
number of seconds in the text box.
To upload while the trigger is active, select Upload while trigger is active.
In the Image Frequency text box, from the drop-down list select the number of
frames per seconds from 1-15 for the upload.
39
Page 53
CB-5222 User and Installation Guide
Note:
This option is valid only when using MJPEG as the camera stream.
Note:
Make sure that SMTP configuration has been completed. See Mail for
details.
From the E-Mail address drop-down list, select one of the two e-mail addresses.
From the Pre-trigger buffer and Post-trigger buffer drop-down lists, select the
number of frames for the buffer from 1-20 frames.
Figure 35: Triggered Action – Upload Image by E-Mail
Check the Continue image upload box if you wish to upload an image by e-mail for a
defined period of time or while the trigger is active. Select one of the following
options:
To specify the length of time for the upload, select Upload for and enter the
number of seconds in the text box.
To upload while the trigger is active, select Upload while trigger is active.
In the Image Frequency text box, from the drop-down list select the number of
frames per seconds from 1-15 for the upload.
Click Save after configuring the settings.
File Name
File Name – Enter a file name in the field, for example image.jpg. The uploaded image’s file
name format is set in this section. Select one that meets your requirements.
Add date/time suffix (default setting)
File name: imageYYMMDD_HHNNSS_XX.jpg
Y: Year, M: Month, D: Day
H: Hour, N: Minute, S: Second
X: Sequence Number
Add sequence number suffix (no maximum value)
File name: imageXXXXXXX.jpg
X: Sequence Number
Add sequence number suffix (limited value)
File Name: imageXX.jpg
X: Sequence Number
The file name suffix ends at the number being set. For example, if the setting is up to
“10,” the file name will start from 00, end at 10, and then start over again.
40
Page 54
Configuration and Operation
Note:
Make sure that FTP configuration has been completed. See FTP for details.
Overwrite
The original image in the FTP site will be overwritten by the new uploaded file with a
static filename.
Click SAVE after configuring the settings.
9.2.1.4.2 Network Failure Detection
The network failure detection function allows the IP camera to periodically ping another IP device
within the network to detect a network failure if, for example, a video server is disconnected. It can
be associated with an action of sending a notification via an alarm output, e-mail or FTP message.
Figure 36: Events Setup > Network Failure Detection Screen
Detection Switch
The Administrator can select from the following options:
Select Off to disable an alarm (default setting).
Select On to enable an alarm.
Select By Schedule to set a schedule. Then click Please Select to select up to 10 schedules
from the drop-down list that opens. The selected schedules are displayed in the Please
Select text box. To set a schedule, open the Schedule tab.
Click SAVE after configuring the settings.
Detection Type
In the text box, enter the IP address to ping and the time interval (in minutes) between pings. Click
Save after configuring the settings.
Triggered Action
The Administrator can specify various alarm actions to be taken when an alarm is triggered. The
following options are available:
41
Page 55
CB-5222 User and Installation Guide
Note:
Make sure that SMTP configuration has been completed. See Mail for details.
Note:
This function is not used for recording live video.
Click SAVE after configuring the settings.
Schedule
The Schedule screen is used to set schedules for recording of events triggered in the Events Setup >
IO and Events Setup > Network Failure Detection screens.
Figure 37: Schedule Screen
The functions in this tab allow administrators to create customized schedules for the camera that
uses this option. If a schedule exists, the administrator can apply that schedule to this camera using
the available drop-down list.
To create a new schedule or edit an existing schedule
Click the appropriate checkboxes relating to the days of the week (Sun, Mon, Tue, Wed,
Thu, Fri and Sat) to create a schedule.
Set Start time (for example, 09:00) and Duration (for example, 4:00 hours).
Click SAVE to apply the newly created schedule to the camera.
To remove a schedule
Select the schedule by clicking the line.
Click DELETE to remove the schedule.
42
Page 56
Configuration and Operation
Note:
1. Make sure the selected file path contains valid characters.
2. When using Windows 8 OS, the storage location cannot be C:\. You must define a storage
location that does not require Administrator privileges on the PC.
Log File
User
Information
Factory
Default
Software
Version
Software
Upgrade
Parameters
File Location
From the File Location screen, specify a storage location for snapshots and web recordings. The
default setting is: C:\. After confirming the setting, click SAVE to save the snapshots and recordings in
the designated location.
Figure 38: File Location Screen
Maintenance
The Maintenance section on the sidebar includes the following tabs:
9.2.1.7.1 Log File
The log file provides information about connections after system boot-up. Click Log File to view the
system log file. The Log File screen opens.
Figure 39: System Log Screen
43
Page 57
CB-5222 User and Installation Guide
Note:
User privileges are defined in the Security > User screen.
9.2.1.7.2 User Information
The Administrator can view each user’s login information and privileges in the User Information
screen shown below.
View User Login Information
Click GET USER INFORMATION to see each user’s details. For example: admin: admin. This indicates
that the user’s login username is admin and the password is admin.
Figure 40: View Information > User Information Screen
View User Privilege
Click GET USER PRIVACY to view each user’s privileges.
Figure 41: View Information > User Information – Get User Privacy Screen
By default, the Admin is granted all privileges: 1 (I/O access), 2 (Camera control), 3 (Talk), 4 (Listen),
and 5 (Analytics). In this example, the user “Alvie” has been assigned all privileges except Analytics.
44
Page 58
Configuration and Operation
Note:
The IP address and all other settings will be restored to factory default settings.
Note:
Analytics firmware is stored in a separate file than the camera system firmware. To backup and
restore the analytics firmware version, see Analytics > Backup & Restore.
Note:
To view the analytics firmware version, see Analytics > Firmware.
9.2.1.7.3 Factory Default
The Factory default screen is shown below. Follow the instructions to reset the camera system
settings to factory default settings if needed.
Figure 42: Factory Default Screen
Full Restore
Click FULL RESTORE to restore the factory default settings of the camera system. The system restarts
in 30 seconds.
Partial Restore
Click PARTIAL RESTORE to restore the factory default settings of the camera system, but save the
network settings. The system restarts in 30 seconds.
Analytics Restore
Click ANALYTICS RESTORE to reset the analytic firmware.
Reboot
Clicking REBOOT restarts the system without changing current settings.
9.2.1.7.4 Software Version
The current version of the camera system software is displayed in the Software version screen.
Figure 43: Software Version Screen
45
Page 59
CB-5222 User and Installation Guide
Note:
1. Make sure that the software upgrade file is available before performing a software upgrade.
2. Analytics firmware is stored in a separate file than the camera system software. To upgrade
the analytics firmware version, see Analytics > Firmware.
3. Do not change the upgrade file name or the system will fail to find the file.
Warning:
1. Do not unplug power while entering file names.
2. Do not unplug power or change the screen while upgrading software.
Avertissement:
Ne débranchez pas l'alimentation pendant la modification des noms de fichiers.
Ne débranchez pas l'alimentation pendant la mise à niveau du logiciel.
9.2.1.7.5 Software Upgrade
Select the Software Upgrade tab to select binary files to upload and upgrade. The Software Upgrade
screen is shown below.
Figure 44: Software Upgrade Screen
To upgrade the software
In the Step 1 text box, click Browse and select the binary file to be uploaded, for
example, uImage_userland_ioi_HD_camera_20151023.img.
From the drop-down list of binary files in Step 2, select the uImage_userland File
Type to upgrade.
Figure 45: File Type Drop-Down List
Click UPGRADE. The system verifies that the upgrade file exists and begins to upload the
file. The upgrade status bar is displayed on the screen. After the upgrade process has
finished, the Home page is displayed.
46
Page 60
Configuration and Operation
Note:
Slide the sidebar located on the right of the screen to view the entire list of parameters.
Note:
1. The camera firmware and the analytics firmware use separate configuration files. For analytic
firmware configuration file, see Analytics > Backup & Restore.
2. It is not possible to import or export analytic settings from this screen.
Warning:
Do not unplug power while changing file names.
Avertissement:
Ne débranchez pas l'alimentation pendant la modification des noms de fichiers.
9.2.1.7.6 Parameters
The Parameters screen enables viewing all of the system’s parameter settings (excluding analytics
parameters).
Figure 46: Parameters Screen
Import/Export
From the Import/Export screen, you can save system settings by importing and exporting the
configuration file (.bin) to a specified location for future use.
Figure 47: Import/Export Screen
47
Page 61
CB-5222 User and Installation Guide
Video
Format
Video
Compression
Video OCX
Protocol
Video Frame
Rate
Audio
To export a configuration file
Click EXPORT. An information bar opens.
Figure 48: Configuration File Information Bar
Click Save.
Specify a location to save the configuration file.
To import a configuration file
Click Browse to select the configuration file
Click UPLOAD. The file is uploaded to the camera.
9.2.2 Streaming Settings
Select the Streaming tab in the navigation bar at the top of the screen to display the configurable
video and audio selections in the sidebar. The Administrator can configure specific video resolution,
video compression mode, video protocol, audio transmission mode, etc. Further details of these
settings are specified in the following sections:
Video Format
From the Video Format screen, you can configure the following settings:
Video Resolution
GOV Settings
H.264 Profile
Figure 49: Streaming > Video Format Screen
48
Page 62
Configuration and Operation
PAL
NTSC
1920 x 1080
1920 x 1080
1280 x 720
1280 x 720
720 x 576
720 x 480
Video Resolution
The ioi HD camera supports H.264/MJPEG streaming for resolutions up to 1080p. The default setting
is 1920 x 1080. Both H.264 and MJPEG streaming support analog BNC video connections.
Following are the supported resolutions:
GOV Settings
You can set the GOV length to determine the frame structure (I-frames and P-frames) in a video
stream for saving bandwidth. The setting range is from 1 to 255. A longer GOV decreases the
frequency of I-frames. Click SAVE to confirm the GOV setting.
H.264 Profile
The H.264 standard defines 21 sets of capabilities. These are referred to as profiles and they target
specific classes of applications. In the security industry, the most common are as follows:
Baseline Profile (BP)
Primarily for low-cost applications that require additional data loss robustness, Baseline
Profile is used in some videoconferencing and mobile applications. This is the most common
profile used in IP security cameras due to the low computational cost of processing the video
using this profile.
Main Profile (MP)
This profile provides improved picture quality at reduced bandwidths and storage costs and
is becoming more common as the camera processors (DSPs) become more able to handle
the processing load. Main Profile can save 10-30% over Baseline. This is the default setting.
High Profile (HP)
High Profile is the primary profile for HD broadcast and Blu-ray HD disc media applications. It
can save 10-30% of the storage cost over Main Profile. However, it may also increase video
latency, depending on the stream structure. ioi HD models default to the Main Profile to
provide the best trade-off between storage size and video latency.
Click SAVE to confirm the settings.
49
Page 63
CB-5222 User and Installation Guide
Note:
CBR mode affects image quality.
Video Compression
From the Video Compression screen, you can specify MJPEG and H.264 compression settings.
Figure 50: Streaming > Video Compression Screen
MJPEG Compression Setting
A higher value implies higher bit rates and higher visual quality. The default setting of the MJPEG
Q Factor is 35. The setting range is from 1 to 45. Click SAVE to confirm the setting.
H.264 Compression Setting
The default setting of H.264 is 2074 kbps. The setting range is from 64 to 8192 kbps. Click SAVE to
confirm the setting.
Compression Information Setting
Select the checkbox to display compression information on the Home page. The default setting is
Display compression information in the home page. Click SAVE to confirm the setting.
CBR Mode Setting
If available bandwidth is limited, check Enable H.264 CBR mode to use Constant Bit Rate. The default
setting is Enable H.264 CBR mode. To operate the camera in Variable Bit Rate (VBR) mode, uncheck
the CBR checkbox. Click SAVE to confirm the setting.
50
Page 64
Configuration and Operation
Video OCX Protocol
From the Video OCX Protocol screen, you can select various protocols for streaming media over the
network. In the case of multicast networking, select Multicast mode.
Figure 51: Streaming > Video OCX Protocol Screen
Video OCX protocol setting options include:
RTP over UDP (default setting)
RTP over RTSP (TCP)
RTSP over HTTP
MJPEG over HTTP
Multicast mode – Enter in each field all required data, including Multicast H.264 Video
Address and Port, Multicast MJPEG Video Address and Port, Multicast Audio Address and
Port, and Multicast TTL. The default Multicast TTL (time-to-live) setting is 1, which prevents
multicast datagrams from being forwarded beyond a single sub-network.
Click SAVE to confirm the settings.
Video Frame Rate
From the Video Frame Rate screen, you can specify the frames per second (fps) for each video
compression format.
Figure 52: Streaming > Video Frame Rate Screen
51
Page 65
CB-5222 User and Installation Guide
MJPEG/H.264 Frame Rate Setting
The default setting of the MJPEG frame rate is 30 fps in NTSC and 25 fps in PAL.
The default setting of the H.264 frame rate is 30 fps in NTSC and 25 fps in PAL The setting
range is from 1 to 30 in NTSC and 1 to 25 in PAL. Settings are:
PAL: 1, 5, 13, and 25 fps
NTSC: 1, 2, 3, 6, 7.5, 10, 15, and 30 fps
Click SAVE to confirm the settings.
Audio
From the Audio screen you can select the Transmission Mode, Server Gain, and Bit Rate.
To set the Transmission Mode
Select one of the following options:
Full-duplex (Talk and listen simultaneously) – In this mode, the local and remote sites
can communicate with each other simultaneously, i.e. both sites can speak and be
heard at the same time. This is the default setting.
Half-duplex (Talk or listen, not at the same time) – In this mode, the local or remote
site can only talk or listen to the other site at one time.
Simplex (Talk only) – In this mode, the local/remote site can only talk to the other site.
Simplex (Listen only) – In this mode, the local/remote site can only listen to the other
site.
Disable – Select this option to turn off the audio transmission function.
To set the Server Gain
From the Input gain drop-down list, select a setting from 1 to 10 or Mute, which turns
off the audio. The default setting is 3.
From the Output gain drop-down list, select a setting from 1 to 6 or Mute, which turns
off the audio. The default setting is 3.
Figure 53: Audio Screen
52
Page 66
Configuration and Operation
Note:
Latitude does not support G.726 bit rates.
Exposure
Picture
Adjustment
Advanced
Picture Settings
IR Function
Miscellaneous
To set the Bit Rate
Select one of the following settings: 16 kbps (G.726), 24 kbps (G.726), 32 kbps (G.726),
40 kbps (G.726), µLAW (G.711) and ALAW (G.711). Both µLAW and ALAW signify 64
kbps, but in different compression formats. A higher bit rate enables higher audio
quality, but requires higher bandwidth. The default setting is uLAW.
Click SAVE to confirm the settings.
9.2.3 Camera Settings
From the Camera tab, the administrator can adjust the following camera settings:
Exposure
The Exposure screen is used to configure lens settings and exposure modes. The exposure is the
amount of light received by the camera’s sensor. It is determined by the sensor’s shutter speed, lens
aperture, and scene illumination.
Administrators may configure the camera to automatically select an exposure level using a
programmed algorithm or set a manual level. The higher the shutter speed that the administrator
selects, the lower the exposure level and vice versa.
The displayed Exposure screen depend on whether Shutter WDR is configured as On or Off in the
Camera > Misc. screen.
9.2.3.1.1 Exposure Screen with Shutter WDR On
Two exposure options are available when Shutter WDR is set to On: WDR Multiple Shutter and WDR
Multiple Shutter RSS.
Figure 54: Exposure Screen with Shutter WDR On
53
Page 67
CB-5222 User and Installation Guide
Caution:
Using a slow shutter speed causes moving objects to be blurred.
Attention:
L'utilisation de vitesses d'obturation faibles peut rendre les objets en mouvement flous.
Caution:
The noise level might increase if the gain level is set too high in low-light scenes.
Attention:
Le niveau de bruit peut augmenter si le niveau de gain est trop élevé dans les scènes
à faible luminosité.
WDR Multiple Shutter
Min Shutter Speed
WDR Multiple Shutter
Min Shutter Speed
PAL
NTSC
PAL
NTSC
1/425
1/500
1/100
1/100
1/300
1/350
1/75
1/90
1/215
1/250
1/50
1/60
1/150
1/180
1/25
1/30
1/120
1/125
1/12
1/15
To set the Exposure mode
From the Auto Mode Max Gain drop-down list, set the maximum gain in 3db steps from
Off to 54dB. Increasing the gain lightens dark pictures resulting from low-level lighting.
The default setting is 36dB.
Select one of the following modes:
WDR Multiple Shutter (True WDR) – This is the default setting. In WDR Multiple
Shutter mode, the camera’s shutter speed works automatically to achieve a consistent
video output level. Select the shutter speed that provides the ideal image quality
according to the environmental luminance.
From the drop-down list, select Normal or WDR First.
Normal – Select this setting for low-light conditions.
WDR First – This mode is recommended for indoor environments with mixed
lighting sources where the main source is indoor lighting and natural light
enters the scene through windows and other exposed areas. The setting
reduces the overexposure in the area with natural lighting.
From the Min Shutter Speed drop-down list, select a shutter speed from 1/12 to
1/425 sec (PAL) or 1/15 to 1/500 sec (NTSC). The default setting is 1/12 (PAL) or
1/15 (NTSC). The following table displays the options.
Click SET to confirm the new setting.
54
Page 68
Configuration and Operation
WDR Multiple Shutter RSS
Min Shutter Speed
WDR Multiple Shutter RSS
Min Shutter Speed
PAL
NTSC
PAL
NTSC
1/425
1/500
1/100
1/100
1/300
1/350
1/75
1/90
1/215
1/250
1/50
1/60
1/150
1/180
1/25
1/30
1/120
1/125
1/12
1/15
WDR Multiple Shutter RSS – This setting is recommended when flickering occurs in
indoor applications where fluorescent lighting is used. The shutter speed decreases in
order to compensate for decreased ambient lighting.
Figure 55: Multiple Shutter RSS Exposure Screen
From the drop-down list, select Normal or WDR First.
Normal – See explanation above.
WDR First – See explanation above.
From the Min Shutter Speed drop-down list, select a shutter speed. A fixed
exposure is set, while other parameters can change. The range is from 1 to 1/500
sec (NTSC) or 1/1.5 to 1/425 sec (PAL). The following table displays the options.
Click SET to confirm the new setting.
9.2.3.1.2 Exposure Screen with Shutter WDR Off
Five exposure options are available when Shutter WDR is set to Off: Auto Iris, Auto Shutter, Shutter
Priority, Flickerless, and Manual Mode.
Figure 56: Exposure Screen with Shutter WDR Off
55
Page 69
CB-5222 User and Installation Guide
Caution:
Using a slow shutter speed causes moving objects to be blurred.
Attention:
L'utilisation de vitesses d'obturation faibles peut rendre les objets en mouvement flous.
Caution:
The noise level might increase if the gain level is set too high in low-light scenes.
Attention:
Le niveau de bruit peut augmenter si le niveau de gain est trop élevé dans les scènes
à faible luminosité.
Auto Iris
Min Shutter Speed
PAL
NTSC
1/25
1/30
1/12
1/15
To set the Exposure mode
From the Auto Mode Max Gain drop-down list, set the maximum gain in 3db steps from
Off to 54dB. Increasing the gain lightens dark pictures resulting from low-level lighting.
The default setting is 36dB.
Select one of the following modes:
Auto Iris– This mode is recommended to be used in indoor environments involving
mixed lighting sources where the main source is fluorescent lighting combined with
natural light that enters the scene through windows and other exposed areas.
This mode limits the shutter speed in order to prevent flickering. The exposure priority
is given to the iris. Shutter speed will be slower in low-light scenes according to the
minimum shutter speed set below. The AGC circuit functions automatically in
cooperating with the iris to achieve a consistent exposure output.
From the Min Shutter Speed drop-down list, select one of the following shutter speed
options. The default setting is 1/12 (PAL) or 1/15 (NTSC).
Auto Shutter – This is the default exposure mode of the camera. It is recommended
for the following scenarios: outdoor environments or indoor environments with
unified lighting (either with constant or changeable lighting conditions), as long as the
main light source is a flickering light source, such as fluorescent lighting.
Select this mode so that the camera’s shutter speed works automatically to achieve a
consistent video output level. You can select a suitable minimum shutter speed
according to the environmental luminance.
56
Page 70
Configuration and Operation
Auto Shutter
Min Shutter Speed
Auto Shutter
Min Shutter Speed
PAL
NTSC
PAL
NTSC
1/425
1/500
1/100
1/100
1/300
1/350
1/75
1/90
1/215
1/250
1/50
1/60
1/150
1/180
1/25
1/30
1/120
1/125
1/12
1/15
Shutter Priority
Shutter Speed
Shutter Priority
Shutter Speed
PAL
NTSC
PAL
NTSC
1/425
1/500
1/100
1/100
1/300
1/350
1/75
1/90
1/215
1/250
1/50
1/60
1/150
1/180
1/25
1/30
1/120
1/125
Flickerless
Min Shutter Speed
PAL
NTSC
1/100
1/100
1/75
1/90
1/50
1/60
1/25
1/30
1/12
1/15
Caution:
Noise levels can be compromised using the 2DNR/3DNR functions.
Attention:
Les niveaux de bruits peuvent être compromis avec les fonctions 2DNR/3DNR.
From the Min Shutter Speed drop-down list, select one of the following shutter speed
options. The shutter speed range is from 1/12 to 1/425 sec (PAL) to 1/15 to 1/500 sec
(NTSC). The default setting is 1/12 (PAL) or 1/15 (NTSC).
Shutter Priority – Select this mode to set a fixed shutter speed while other parameters
can change. The shutter speed range is from 1/25 to 1/425 sec (PAL) to 1/30 to 1/500
sec (NTSC). The default setting is 1/25 (PAL) or 1/30 (NTSC). From the Shutter Speed
drop-down list, select one of the following shutter speed options.
Flickerless – This mode is used to eliminate flicker for indoor applications where
fluorescent lighting is used. The darker the ambient lighting, the slower the shutter
speed should be. The shutter speed range is from 1/12 to 1/100 sec (PAL) or 1/15 to
1/100 sec (NTSC). The default setting is 1/12 (PAL) or 1/15 (NTSC). From the Min
Shutter Speed drop-down list, select one of the following shutter speed options.
Manual Mode – This mode should only be used in indoor scenes with consistent
lighting. Manual Mode opens the iris completely and requires the user to set values
for shutter and gain levels. Increasing the value of the fixed shutter increases the
amount of light entering the sensor. This allows a brighter and more detailed image.
Similarly, utilizing gain and increasing its level increases the sensitivity of the image
sensor, which brightens the image and add details. This increases the level of noise in
the image.
57
Page 71
CB-5222 User and Installation Guide
Manual Mode
Fixed Shutter Speeds
Manual Mode
Fixed Shutter Speeds
PAL
NTSC
PAL
NTSC
1/10000
1/10000
1/215
1/250
1/3500
1/4000
1/150
1/180
1/2500
1/3000
1/120
1/125
1/1750
1/2000
1/100
1/100
1/1250
1/1500
1/75
1/90
1/1000
1/1000
1/50
1/60
1/600
1/725
1/25
1/30
1/425
1/500
1/12
1/15
1/300
1/350
Figure 57: Manual Exposure Mode with Shutter WDR Off
From the Shutter drop-down list, select a suitable shutter speed according to the
environmental luminance from 1 to 1/10000 sec (PAL) or 1 to 1/10000 sec (NTSC). The
default setting is 1/150 (PAL) or 1/180 (NTSC). The following table displays the options.
From the Gain drop-down list, set the maximum gain in 3db steps from Off to 54dB.
Increasing the gain lightens dark pictures resulting from low-level lighting. The default
setting is 36dB.
Click SET to confirm the new setting.
Picture Adjustment
Adjustment of some qualities of the video is made possible by selecting Picture Adjustment in the
Camera tab. Brightness, Sharpness, Contrast, Saturation and Hue may all be adjusted via drop-down
lists from this window, as shown below.
Figure 58: Picture Adjustment Screen
58
Page 72
Configuration and Operation
Caution:
Noise levels can be compromised using the 2DNR/3DNR functions.
Attention:
Les niveaux de bruits peuvent être compromis avec les fonctions 2DNR/3DNR.
Brightness
You can adjust the image’s brightness by adjusting this parameter. Select from the range between
+1 to +25. To increase video brightness, select a larger number. The default setting is 0. Click SET to
confirm the new setting.
Sharpness
Increasing the sharpness level can make the image look sharper, especially enhancing the object’s
edge. Select from the range between -15 to +10 in 1dB steps. The default setting is -10. Click SET to
confirm the new setting.
Contrast
Camera image contrast level is adjustable: select from a range of -13 to +12 in 1dB steps. The default
setting is 0. Click SET to confirm the new setting.
Saturation
Camera image saturation level is adjustable: select from a range of -12 to +13. The default setting is
0. Click SET to confirm the new setting.
Hue
Camera image hue level is adjustable: select from a range of +1 to +12. The default setting is 0. Click
SET to confirm the new setting.
Advanced Picture Settings
The options for the Advanced Picture Settings screen depend on whether Shutter WDR is configured
as On or Off from the Camera > Misc. screen. In both cases, 3DNR and 2DNR noise reduction settings
are configured from this screen.
Advanced Picture Settings with WDR On
When Advanced Picture Settings are enabled (configured as On), the user can configure only 3DNR
and 2DNR settings from this screen.
Figure 59: Advanced Picture Settings Screen with WDR On
3DNR
3DNR provides superior noise reduction and is recommended for use in in extra low-light conditions.
It is especially useful for reducing blur with moving objects. There are four options for 3D Noise
Reduction (3DNR). A higher level of 3DNR generates relatively enhanced noise reduction. From the
drop-down list, select Off, Low, Middle or High. The default setting is Low. Click SET to confirm the
new setting.
59
Page 73
CB-5222 User and Installation Guide
2DNR
The 2DNR Noise Reduction function analyzes pixel by pixel and frame by frame to eliminate
environmental noise and deliver optimized image quality, especially in low-light conditions. From the
drop-down list, select Disable or Enable. The default setting Disable. Click SET to confirm the new
setting.
Advanced Picture Settings with WDR Off
When Advanced Picture Settings are disabled (configured as Off), in addition to 3DNR and 2DNR
settings, the user can configure Backlight Compensation and Gamma WDR from this screen.
Figure 60: Advanced Picture Settings Screen with WDR Off
Backlight compensation is used in images where a bright light source is behind the subject of
interest. Without backlight compensation, the subject would normally appear in silhouette. The
backlight function of the camera allows it to adjust the exposure of the entire image to properly
expose the subject in the foreground. The default setting Off.
To configure backlight compensation
From the Camera > Misc. screen, select Shutter WDR Off.
From the Camera > Advanced Picture Settings screen’s Backlight drop-down list, select
On.
Click SET.
Gamma WDR, also known as Digital WDR, improves the image quality and amount of details in high
contrast scenes. Such scenes combine areas with different lighting conditions, where some areas are
very bright and others are dark. If this function was not used, the image either would be
overexposed or too bright in bright areas and completely dark in dark areas. Gamma WDR helps to
improve image quality by producing a larger amount of details in both the dark and bright areas of
the image. The default setting On.
To configure Gamma WDR
From the Camera > Misc. screen, select Shutter WDR Off.
From the Camera > Advanced Picture Settings screen’s Gamma WDR drop-down list,
select On.
60
Click SET.
Page 74
Configuration and Operation
Note:
The selection of Shutter WDR On or Off determines which Camera > Exposure screen is
displayed.
Note:
After changing the video format, the camera resets and restarts automatically. The camera
restores to factory defaults and the analytics settings are deleted.
IR Function
The IR Function setting activates the IR Cut (IRC) filter for day/night operation. The day/night IRC
switching mechanism operates according to the ambient light level.
Figure 61: IR Function Screen
From the Day/Night Function drop-down list, select one of the four settings:
Auto – The camera converts from Day mode (color) to Night mode (monochrome)
automatically at nighttime or in low light conditions. When there is sufficient light,
the camera switches automatically from Night mode to Day mode. This is the default setting.
Night – Activates IR mode by putting the camera into monochrome (Night) mode.
Day – Deactivates IR mode by putting the camera into color (Day) mode.
Smart – Default mode. Smart mode enhances monochrome/Night mode stability when IR
illumination is dominant and keeps the camera from switching between Day and Night
modes. In this mode, the IR Cut filter is on (i.e. monochrome/Night mode) when an external
IR LED projector also is activated. This prevents the camera from returning to color/Day
mode.
Click SET to confirm the new setting.
Misc. Screen
The Misc. (Miscellaneous) screen is used for setting the TV system standard and for enabling Shutter
WDR.
Figure 62: Misc. Screen
TV System
Select the video format that matches your TV system: PAL or NTSC. The default setting is NTSC. Click
SET to confirm the new setting.
61
Page 75
CB-5222 User and Installation Guide
Figure 63: Shutter WDR On
Figure 64: Shutter WDR Off
Shutter WDR
The Shutter WDR (Wide Dynamic Range) function, also known as True WDR or multi-exposure WDR,
resolves high contrast or changing light issues and creates a constant video output level. The camera
creates a new image with a wide dynamic range by using a combination of slow- and fast-exposure
shutters and an algorithm to determine the optimal mix of light and dark regions within the scene
from the two shutters.
Shutter WDR is selectable between On or Off:
When On is selected, the image has a wide dynamic range, so that the IP camera can capture
a greater scale of brightness. This is the default setting.
Selecting Off disables this function.
Click SET to confirm the new setting.
62
Page 76
Configuration and Operation
9.2.4 Analytics Settings
The ioi HD camera includes a rich set of video analytic functionality embedded in its firmware. The
Analytics tab contains menus for defining the camera’s Field of View depth and detection rules,
including region entrance, loitering, tripwire crossover, fence trespass, unattended baggage,
stopped vehicle, and object removal.
Figure 65: Analytics > Manual Depth Screen
In real-time, the camera sends notifications and alarms upon the occurrence of events. You can set
customizable rules and criteria to define the perimeter, region, and what to detect. The camera’s
analytic software ensures a high probability of detection with an extremely low false alarm rate.
Use the Analytics tab to configure the following functions:
Depth
Rules
Responses
Scheduled Actions
On-Screen Display
Firmware
Backup & Restore
63
Page 77
CB-5222 User and Installation Guide
Caution:
The camera is disarmed when configuring Analytics. Detection will not take place until
the camera is manually re-armed from the Home screen.
Attention:
La caméra est désactivée lors de la configuration d'Analytics. La détection n'aura lieu
qu'après que la caméra soit réactivée depuis l'écran Accueil.
Note:
The Auto screen remains the default setting unless you select the Manual depth screen. If you
select the Manual screen and click APPLY, the Manual screen remains the default setting until
you select the Auto screen again and the Auto Calibration process is completed.
Depth
The Depth screen enables you define the perspective of the scene being monitored and to. It is used
to set human markers, ground guidelines, camera height, horizon, and advanced depth regions (such
as hills, planes and fences), which create a virtual 3D model for measurement of distances and sizes
from the perspective of the camera. The screen contains a wizard that facilitates configuring the
depth settings. See Figure 65: Analytics > Manual Depth Screen (page 63).
9.2.4.1.1 Automatic Calibration
Depth settings can be configured automatically by using the Auto Calibration (automatic depth
calibration) algorithm from the Auto depth screen. By default, the Auto screen is displayed.
Figure 66: Auto Depth Screen - Auto Calibration
64
Page 78
Configuration and Operation
Note:
If you use the Auto Calibration function, it is possible to configure additional settings manually
and verify the Auto Calibration settings after the Auto Calibration process is completed. Click
MANUAL in order to configure additional settings.
Note:
While Auto Calibration is in progress, you can proceed with the next steps in the
analytic configuration.
Caution:
1. The Auto Configuration algorithm takes at least five minutes to run. If you stop
the procedure before the progress bar reaches 100%, the analytic process will
reset.
2. If you change from Auto to Manual mode, you must wait until the analytic
process resets in order to use Manual mode.
The Auto Calibration function automatically configures scene depth and calculates camera height,
focal length, and tilt angle according to the scene depth. The system discovers people in the scene
and configures human markers automatically. This function eliminates the time and effort required
to manually add human markers.
To automatically configure depth settings
1. Verify that the camera is installed at a height of at least four meters (13 feet).
2. Verify that the horizon is less than 30% of the Field of View (FoV).
Figure 67: Horizon Line
3. From the Settings tab, select Analytics > Depth. The Auto depth screen opens. See
Figure 66: Auto Depth Screen - Auto Calibration.
4. From the Units drop-down list, select Feet or Meter.
5. Select Set estimated height.
6. Enter the estimated camera height in the text box.
7. Click START. The camera automatically calibrates the depth.
8. Be sure that a person is walking along the Y (Vertical) axis of the FoV while Auto
Calibration is in process. When the progress bar reaches 100%, the Auto Calibration is
completed and the calculated results are displayed.
9. Select the Auto > Step 2: Verification tab.
65
Page 79
CB-5222 User and Installation Guide
Note:
If the results are unsatisfactory, run Auto Calibration again (follow Step #1 onscreen) or click MANUAL to manually configure the depth settings.
Note:
1. It is possible to select the Step 4: Verification tab to verify and apply settings at any
time.
2. For detailed instructions how to set markers and guidelines, follow instructions in
the HTML Edition Units User’s Guide.
10. Verify that the horizon, camera height, and human marker settings are correct.
11. After finishing the Auto Configuration, click the MANUAL tab.
12. Select the Manual > Step 4: Verification tab to complete the depth configuration.
9.2.4.1.2 Manual Depth Calibration
If you select the MANUAL depth button, there are two methods to manually configure depth
settings:
If you are performing setup by yourself, click the Solo Setup tab.
If you are not performing setup alone, proceed to Configuring Ground and Height Settings.
9.2.4.1.3 Solo Setup
The Solo Setup function enables you to install and setup the camera at a remote site without
requiring another person’s assistance. It is very useful and should be used even if you have another
person’s assistance.
With this feature, you can:
Move around within the camera’s Field of View.
Use the camera to record a set of snapshots of the scene while the user is moving around
the camera Field of View. Creating the recording of the person in the FoV can be used to
adjust settings without requiring another physical walk through the FoV.
Use the recording of his movement to setup the depth by marking his height on the
camera’s Field of View.
66
Page 80
Configuration and Operation
Follow the instructions in the Solo Setup tab to single-handedly setup the camera:
Figure 68: Analytics > Depth > Solo Setup Instructions
67
Page 81
CB-5222 User and Installation Guide
Icon
Function
Notes
Start Recording
Starts recording and browses to destination folder
where the clip will be saved
Stop Recording
Stops recording
Browse
Browses to the destination folder where clip is stored
and loads the clip
Play/Pause
Speed X1/X0
Fast Forward
Speed X2, X4, X8, X16. Click to increase or decrease
speed.
Rewind
Speed -X2, -X4, -X8, -X16. Click to increase or decrease
speed.
To perform a solo setup
1. Click the Solo Setup tab. The Solo Setup keypad opens with the following control icons:
2. On the Solo Setup control keypad, click Start Recording to record a view in the
camera’s Field of View.
3. Select a folder where to store the clip. Recording starts when the folder is selected.
4. Walk through various locations across the vertical axis of the camera’s Field of View in
order to place ground and height markers and guidelines in the clip.
5. Click Stop Recording .
6. Click Step 1: Ground & Height and follow the instructions.
7. Click Browse to load the clip from the folder where it is saved.
8. Use the Play , Pause , Fast Forward , and Rewind buttons on the
Solo Setup keypad to explore the clip. The status of the view is displayed on the bottom
left side of the screen.
68
Page 82
Configuration and Operation
Note:
At any time it is possible to click the Verification tab to verify and apply settings.
9. Click the round Play button on the control panel located to the left of the monitor
to exit Clip mode and return to Live mode. The caption under the monitor changes from
Clip to Live.
Figure 69: Analytics > Depth Control Panel
10. Proceed to the tabs for Steps 2-4 of the Depth Setup to complete the setup and apply
settings.
69
Page 83
CB-5222 User and Installation Guide
9.2.4.1.4 Configuring Ground and Height Settings
If you are not performing a solo setup, do the following:
To configure ground and height settings
1. Click the Step 1: Ground & Height tab. The Step 1: Ground & Height screen opens.
70
Figure 70: Analytics > Depth > Step 1: Ground & Height Screen
2. Follow the instructions on screen.
Figure 71: Analytics > Depth > Step 1: Ground & Height Instructions
3. Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring
these settings.
4. Click APPLY when finished or continue to the next step.
Page 84
Configuration and Operation
9.2.4.1.5 Configuring Camera and Horizon Settings
After completing Solo Setup or manually configuring ground and height settings, configure camera
height and horizon settings. The Camera & Horizon tab is used for manually discovering people in
the scene and configuring human markers.
To manually configure camera and horizon settings
1. Click the Step 2: Camera & Horizon tab. The Step 2: Camera & Horizon screen opens.
Figure 72: Analytics > Depth > Step 2: Camera & Horizon Screen
2. Follow the on-screen instructions to configure camera and horizon settings.
Figure 73: Analytics > Depth > Step 2: Camera & Horizon Instructions
3. Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring
these settings.
4. Click APPLY when finished or continue to the next step.
71
Page 85
CB-5222 User and Installation Guide
9.2.4.1.6 Configuring Advanced Depth Region Settings
After configuring camera and horizon settings, configure advanced depth region settings.
To configure advanced depth region settings
1. Click the Step 3: Advanced Depth Regions tab. The Step 3: Advanced Depth Regions
screen opens.
72
Figure 74: Analytics > Depth > Step 3: Advanced Depth Regions Screen
2. Follow the on-screen instructions to configure advanced depth region settings.
Figure 75: Analytics > Depth > Step 3: Advanced Depth Regions Instructions
Page 86
3. Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring
these settings.
4. Click APPLY when finished or continue to the next step.
9.2.4.1.7 Settings Verification
After configuring advanced depth region settings, verify your settings.
To verify settings
Click the Step 4: Verification tab. The Step 4: Verification screen opens.
Configuration and Operation
Figure 76: Analytics > Depth > Step 4: Verification Screen
73
Page 87
CB-5222 User and Installation Guide
Follow the on-screen instructions to verify settings.
Figure 77: Analytics > Depth > Step 4: Verification Instructions
Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring
these settings.
Click APPLY when finished.
Rules
The Rules tab enables you to define detection rules according to the type of detection you want to
be notified about. By default, the Human or vehicle enter region rule is enabled.
74
Figure 78: Analytics > Rules Screen
Page 88
Configuration and Operation
To select a different rule, click the Human or vehicle enter region link. Select the rule from the drop-
down list.
Figure 79: Rules Drop-down List
You can assign a name for the rule in the Name text box at the top of the screen. Select the Enable
checkbox to activate the rule.
Detection occurs when one or more detection rules are active, the camera is in Arm mode, and the
scenario on the video (scene) fits the detection criterion specified. When the conditions of a
detection rule are met, an alarm is shown in which you can observe the detection and take the
appropriate action.
Rules are configured by clicking the Basic or Advanced Attributes tabs. The Basic tab displays
minimal information for the rule. Click RESTORE DEFAULT to return to factory default settings.
Figure 80: Analytics > Rules > Basic Attributes Tab
The Basic tab includes a setting, Enable detection of small, crawling, or slow intruders, which is
enabled by default. The setting can detect sophisticated intruders (for example a camouflaged or
crawling person) and identify people who are standing or moving upright, which helps to reduce
false alarms.
75
Page 89
CB-5222 User and Installation Guide
Note:
The following limitations apply to this function:
1. It is possible that a person who is not standing upright might not be detected when:
Crawling
Walking on all four (like an animal)
Camouflaged to look like an inanimate object (i.e., small tree)
Running and viewed from the side
Bent over and viewed from the side
2. The camera should not be facing straight down (i.e., it should be at a 30-40 degree
angle from the object).
The Advanced tab displays additional information for the rule. Click RESTORE DEFAULT to return to
factory default settings.
Figure 81: Analytics > Rules > Advanced Attributes Tab
Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings.
76
Page 90
Configuration and Operation
Responses
The camera’s embedded event engine enables you to define a set of responses (automatic actions)
for selected events and to perform actions (scheduled actions) at pre-defined times during a defined
monitoring period. Refer to the HTML Edition Units User’s Guide for detailed instructions on
configuring these settings.
Figure 82: Analytics > Responses Screen
Each automatic response definition includes the following three parameters: Triggering event,
Actions and Schedule.
Figure 83: Responses > Triggering Event Tab
77
Page 91
CB-5222 User and Installation Guide
To define a triggering event
Click ADD. A new Response is displayed in the top of the screen.
Select Enable to activate the Response.
From the Detection by type drop-down list, select one of the following detection types:
Any detection (default), Intrusion detection, Vehicle Stopped, Unattended Object, Object
Removed, Tripwire detection, Fence detection, or Loitering detection. The selection is
displayed in the top of the screen.
From the Detection by rule drop-down list, select a rule that was defined in the Rules
tab.
From the External alarm (dry contact) drop-down list, select Alarm Input -1 or Alarm
Input - 2. Then select Open or Close to trigger an event when the contact is Normally
Open or Normally Closed.
Select No more detections left in scene if you want the triggering event to occur when
there are no additional objects remaining in the scene to be detected.
From the Video Signal drop-down list, select one of the following: Any tamper, Video
Signal Ok, No Video Signal, Low Video Signal, Bad Video Signal, or Camera Shift.
Select one of the following operations to define when the triggering action will occur:
Power on
Arm
Disarm
Click APPLY to save the configuration.
To delete a triggering event
Select the event from the top of the Responses screen.
Click DELETE. The event is deleted.
78
Figure 84: Responses > Actions Tab
Page 92
Note:
Actions related to an analytic event that is defined in this screen are not affected by the status
of the alarm switch configured on the Events Setup > IO screen.
To define an action
From the Action drop-down list, select one of the following Actions. The selection is
displayed at the top of the screen.
Activate relay output
Select Activate relay immediately or enter the number of seconds (1-999) in
Select the Relay number.
Select the Activation signal:
Configuration and Operation
After x seconds drop-down list.
Continuous – From the drop-down list, select On or Off.
Pulse activation – In the Sec. text box, enter the number of seconds for the
Pulse duration.
Click APPLY.
Clear alarms
Select Clear alarms immediately or enter the number of seconds (1-999) in After
x seconds drop-down list.
Click APPLY.
Arm camera
Select Arm immediately or enter the number of seconds (1-999) in After x
seconds drop-down list.
Click APPLY.
Disarm camera
Select Disarm immediately or enter the number of seconds (1-999) in After x
seconds drop-down list.
Click APPLY.
Enable detection rule
Select Perform immediately or enter the number of seconds (1-999) in After x
seconds drop-down list.
Click APPLY.
Disable detection rule
Select Perform immediately or enter the number of seconds (1-999) in After x
seconds drop-down list.
Click APPLY.
79
Page 93
CB-5222 User and Installation Guide
To add an action, click ADD. The action is displayed in the Actions table.
Repeat step 1 for each new Action.
To change the order of the Actions, click UP or DOWN.
To delete an action, select the Action and click DELETE.
Click APPLY when finished.
Figure 85: Responses > Actions Table
To set a schedule
Do one of the following:
Select Always.
Select Monitor event occurrences.
Click APPLY.
80
Figure 86: Responses > Schedule Tab
In the From text box, enter the start date.
In the To text box, enter the end date. If there is no end date, check No end
date.
From the Weekdays list, select the day of the week.
In the Between text box, enter the hours during which the monitoring will
occur.
Page 94
Configuration and Operation
Scheduled Actions (Sched. Actions Screen)
The Sched. Actions screen is used for setting schedules for actions to be taken when an event
occurs.
Figure 87: Sched. Actions > Actions Tab
Each scheduled action includes the following two parameters: Actions and Schedule
To define an action
From the Action drop-down list, select one of the following actions: Activate relay
output, Clear alarms, Arm camera, Disarm camera, Enable detection rule, or Disable
detection rule. The selection is displayed at the top of the screen.
Activate relay output
Select Activate relay immediately or enter the number of seconds (1-999) in
After x seconds drop-down list.
Select the Relay number.
Select the Activation signal:
Continuous – From the drop-down list, select On or Off.
Pulse activation – In the Sec. text box, enter the number of seconds for the
Pulse duration.
Click APPLY.
81
Page 95
CB-5222 User and Installation Guide
Clear alarms
Select Clear alarms immediately or enter the number of seconds (1-999) in After
x seconds drop-down list.
Click APPLY.
Arm camera
Select Arm immediately or enter the number of seconds (1-999) in After x
seconds drop-down list.
Click APPLY.
Disarm camera
Select Disarm immediately or enter the number of seconds (1-999) in After x
seconds drop-down list.
Click APPLY.
Enable detection rule
Select Perform immediately or enter the number of seconds (1-999) in After x
seconds drop-down list.
Select the name of the rule defined in the Rules tab.
Click APPLY.
Disable detection rule
Select Perform immediately or enter the number of seconds (1-999) in After x
seconds drop-down list.
Select the name of the rule defined in the Rules tab.
Click APPLY.
To add an Action, click ADD. The action is displayed in the Actions table at the top of the
screen.
Figure 88: Responses > Actions Table
Repeat step 1 for each Action.
To change the order of the actions, click UP or DOWN.
82
To delete an action, select the action and click DELETE.
Click APPLY when finished.
Page 96
To set a schedule
Do one of the following:
Configuration and Operation
Figure 89: Sched. Actions > Schedule Tab
Select Always.
Select Monitor event occurrences.
In the From text box, enter the start date.
In the To text box, enter the end date. If there is no end date, check No end
date.
From the Weekdays list, select the day of the week.
In the Between text box, enter the hours during which the monitoring will
occur.
Click APPLY.
Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings.
83
Page 97
CB-5222 User and Installation Guide
On Screen Display
The On Screen Display screen determines the information to be displayed on the video screen as an
overlay on top of the video. The settings on this screen define the selection, alignment and color
configuration of the various overlays that appear during normal monitoring, events and detection.
Figure 90: Analytics > On Screen Display Screen
The On Screen Display screen includes the following default settings:
Enable analog video output
Display tracking information
Tracking shape: Rectangle
Display trail enabled (10 seconds)
Tracking color: Custom
Radial button 1: Red
Display camera information
Font: Terminal
Font size: Medium
84
Page 98
Configuration and Operation
Note:
1. Analytics firmware is stored in a separate file than the camera system software. To view the
camera system software version, see System > Software Version. To upgrade the camera
system software version, see System > Software Upgrade.
2. You must close and restart Internet Explorer in order to view the new firmware version.
In the table, select the settings that you want to configure:
In the Display column, select the checkbox to display the display item.
In the Caption column, click Set to change the name of the display item. You cannot change
the names Channel name, Date, Time and Status.
In the Background color, Foreground color, Horizontal Align, and Vertical Align columns,
clicking a field opens a drop-down list. Select one of the options from the drop-down list.
Click APPLY when finished.
Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings.
Firmware
The Firmware screen displays the current analytics firmware version and enables you to update the
unit’s analytics firmware file.
Figure 91: Analytics > Firmware Screen
To update the analytics firmware file
Click Browse
Select the file.
Click UPGRADE.
Using Advanced Settings
In the Advanced Settings area, the Scene with large objects or many objects setting improves analytic
detection in scenes where there are large or multiple objects, and where there is movement in up to
80% of the frame. The setting is enabled by default.
Also in the Advanced Settings area, the Enable enhanced detection setting improves the distance
from which smaller objects are detected. This function is disabled by default.
Click Apply when finished.
Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings.
85
Page 99
CB-5222 User and Installation Guide
Note:
Analytics firmware is stored in a separate file than the camera system software. To backup and
restore the camera system software version, see System > Factory Default.
Backup & Restore
The Backup & Restore screen enables you to create backup files of the unit’s analytics settings and
to restore them.
Figure 92: Analytics > Backup & Restore Screen
To back up the analytic firmware file
Click BACKUP.
To restore the analytic firmware file
Do one of the following:
To restore factory defaults, select To factory defaults.
To restore all defaults from a stored file, select Full restore from file, click Browse to
locate the file path, then select the file.
To restore analytic settings from a stored file, select Analytic settings from file, click
Browse to locate the file path, then select the file.
Click RESTORE.
Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings.
Log Out
Select the Log Out link in the navigation bar to close the session. The following message appears:
Figure 93: Logout Message
To return to the application, click Login. The Login window opens. See Figure 11: Login Window.
86
Page 100
Appendices
Technical Specifications
Internet Security Settings
Install UPnP Components
Deleting the Existing DVPlayer
Deleting Temporary Internet Files
Mounting and Lens Accessories
Appendices
87
Loading...