DVR Mac4 User Manual

COMPACT ACTIVE SPEAKER
350 W RMS MOSFET POWER AMPLIFIER
AUDIO PROCESSOR
ELECTRONIC LIMITER

USER’S MANUAL

GB

CODEM MUSIC S.r.l. - Via Del Vallo, 110 - 61100 PESARO - ITALY

Tel. [phone]- Fax [phone]

hhttttpp::////wwwwww..ccooddeemmmmuussiicc..ccoomm -- EE--mmaaiill:: iinnffoo@@ccooddeemmmmuussiicc..ccoomm

DESCRIPTION

The MAC 4 is a very compact and innovative two-way active speaker that
can ensure an absolute sound quality in any use conditions.
The MAC 4 incorporates a powerful and reliable 350 Wrms power
amplifier with MOS-FET technology designed for making a dynamic and clear
sound, along with a music quality without equal.
The dynamics of trasducers is maximized by the AUDIO SIGNAL
PROCESSOR and the ELECTRONIC LIMITER and it at the same time
protected from signal peaks and distorsion wich could compromise its
lenght.
Thanks to the trasducers quality, the high technological content of its
incorporated power amplifier, the MAC 4 meet the strict demand of PA
system and professional monitoring for any musical instrument or genre.
The particular construction of its back part, with two 45° sides allow the

MAC 4 to be used as a monitor.

USE OF BALANCED INPUTS

MAC4 inputs are BALANCED type, 3 poles XLR CANNON and JACK stereo.

Balanced connection is studied to have a better rejection against the noise
that wires (if very long) takes from external interferences.
Most of professional audio equipment have balanced outputs, you can use
however non balanced connection with mono JACK (or 3 poles CANNON
with pin 3 connected to pin 1) the MAC4 will work normally, but it will be
more sensitive to external interferences.
The JACK and CANNON inputs are connected together (parallel / link).
You can use each one like an input or an output signal for other speaker
systems.

USE OF INPUTS LEVEL

Volume knob adjust the input level of the two inputs.
Normally is preferred to take the knob on the 0 dB level, if you want a
higher sensibility you can take the knob to MAX.
Electronic internal limiter will always control input level to have a safe
operation of the trasducers.

USEFUL TIPS

Thanks to its characteritics you can use MAC 4 for monitoring and sound diffusion or
like sound system for piano-bar and live music.
MAC 4 has been build for vertical, horizontal and 45° installation (like monitor).

On the bottom of the cabinet there is the adapter for speaker stand.

DESCRIPTION OF REAR PANEL

1) Power switch with lamp (0-1) 4) Input level adjutment

2) Power supply 220/240 Vac 50/60 Hz 5) Balanced line input - 3 poles XLR cannon

3) Protection fuse 6) Balanced line input - stereo jack

NOTE:

The two inputs are parallel connected together, you can use one for input and the other like
an output for other speaker systems.

In case of internal amplifier over-heating, the heat-protection turn off the MAC4, when the
temperature return to normal level, automatically the protection turn on again the system.

Input level higher than +10 dB can damage the speaker system.

INPUT
LEVEL

PARALLEL

BALANCED INPUTS

AC-IN

220~240

Vac

50/60 Hz

POWER

ON/OFF

Replace fuse with correct type only

Sostituire il fusibile solo con il tipo corretto

4A /250 Vac

Power consumption:

Potenza assorbita:

450W

MADE

IN ITALY

Serial N°

PROCESSOR CONTROLLED

350 WRMS MOSFET POWER AMPLIFIER

COMPRESSOR/LIMITER

0

MAX

0 dB

+

-

gnd

-

gnd

1

2

3

+

6

4

5

2

3

1

TECHNICAL SPECIFICATION

Type Bass - reflex / 2 way
Low frequency section

380 mm (15”) high efficiency

High frequency section

1“ horn loaded compression driver
Sensitivity 1W/1m 108 dB
Angle of coverage 90° x 75° (horn directivity)
Frequency response

38 - 20.000 Hz
Crossover 18 dB/oct. - Cut freq. 2,2 KHz
Cabinet High density wood covered with moquette
Dimensions Cm 68 x 48 x 40 (H - L - W)
Weight Kg. 33

TECHNICAL SPECIFICATION AMPLIFIER

Type AB class mosfet with audio signal processor
Output power 350 W R.M.S. / 4 Ohm
THD < 0,1 % a 1 Khz
Frequency response

20 - 50.000 Hz
Balanced inputs XLRF + stereo Jack in parallel
Input sensitivity 0 dB / -7 dB max
Input impedance 10 KOhm
Protections

Electronic limiter on the input signal (max +10 db)

Protection fuse on power supply (1 x 4AF)

Double protection fuse on power amplifier (2 x 8AF)

Self-resetting thermal fuse on transformer and power amplifier