DVIGear DVI-3331a User Manual

User Guide

AV-PC-DVI to PC-DVI Converter / Scaler

DVI-3331a

TABLE OF CONTENTS

SECTION PAGE

PRODUCT SAFETY ....................................1

PRODUCT LIABILITY ...................................1

1.0 INTRODUCTION ...................................2

2.0 SPECIFICATIONS ..................................3

3.0 PACKAGE CONTENTS ..............................5

4.0 CONNECTING THE HARDWARE ......................6

5.0 OPERATING THE UNIT ..............................8

6.0 TROUBLESHOOTING ..............................11

7.0 LIMITED WARRANTY ..............................12

8.0 REGULATORY COMPLIANCE .......................12

WARNING – Product Safety

1. Do not dismantle the product housing or modify the printed circuit board
module as this may result in electrical shock or burn.

2. Do not attempt to service this product yourself as opening or removing the
product housing may expose you to dangerous voltages or other hazards.
Refer all servicing to qualied service personnel.

3. Keep this product away from liquids. Spills into the product housing may
result in re, electrical shock, or equipment damage. If liquid spills into the
housing, unplug the product immediately. Have the product checked by a
qualied service engineer before using it again.

4. Place the product in an even and stable location. If the product falls or is
dropped, it may cause an injury and/or malfunction.

5. Avoid exposing the product to extreme temperatures or to high humidity
levels as this may result in damage to the product.

6. Only use the supplied External AC Power Adapter. The use of other power
adapters may cause this product to fail or may cause a re.

7. Do not twist or exert excessive force on the ends of the cables connected to
this product as this may cause it to malfunction. Take care to ensure that all
connected cables are not forced to bend beyond their minimum bend radius.

Product Liability

Every effort has been made to ensure that this product is free of defects.
DVIGear cannot be held liable for the use of this product or for any direct or
indirect consequential damages arising from its use. It is the responsibility of
the users of this product to check that it is suitable for their requirements and
that it is installed correctly.

All rights are reserved. No parts of this manual may be reproduced or transmitted
by any form or means, electronic or mechanical, including photocopying,
recording or by any information storage or retrieval system, without the written
consent of DVIGear.

DVIGear reserves the right to revise any of its hardware and software, following
its policy to modify and/or improve its products where necessary or desirable.
This statement does not affect the legal rights of the user in any way. All
third-party trademarks and copyrights are recognized. The DVIGear logo is a
registered trademark of DVIGear, Inc. HDMI™ is a registered trademark of
HDMI LLC. All other trademarks are the property of their respective holders.

-1-

1.0 INTRODUCTION

The model DVI-3331a is a professional quality Switcher / Cross Converter /
Scaler with dual (analog and digital) outputs. The unit provides user selection
of various input signal formats: DVI-D or HDMI, analog RGB and analog
Component Video. The selected input signal is converted to a digital DVI and
an analog RGB signal. The DVI-3331a accepts a wide range of input signal
resolutions and supports pixel clock rates up to 165 MHz. A high-performance
internal scaling engine enables user selection of output resolutions up to 1080p
and 1920x1200 (WUXGA). A convenient IR remote control further enhances the
unit’s capabilities.

DVIGear’s professional digital signal distribution products have been serving the
industry for over ten years. DVIGear offers a full line of high quality Digital Matrix
Routing Switchers, Splitters, Video Scalers, Up/Down/Cross Converters, Format
Converters, Analog-Digital Converters, as well as a wide range of long-reach
Digital Cables, Extenders, and Optical Transmission systems.

1.1 Features

The model DVI-3331a has several unique and innovative features:

• SupportsanaloganddigitalPC,HDTVandComponentVideoinputs

• User-selectableHDTVandPCoutputresolutionsupto1080p

and 1920x1200 /60 Hz

• DualOutputs:analogRGBanddigitalDVI

• DVIInput/OutputarefullyHDCPcompliant

• FrontPanelandIRremotecontrol

• 3DMotion-AdaptiveDe-Interlacingand3DNoiseReduction

• 3:2Pull-Downcorrectionwith2:2Pull-Downrecovery

• IntuitiveOn-ScreenDisplay(OSD)menus

• Rugged,compactmetalenclosure

• LockingconnectorACPowerAdapterforaddedsecurity

-2-

2.0 SPECIFICATIONS

Performance

Compliance
Maximum Pixel Clock Frequency
Maximum Video Bit Rate
Supported Color Depth
Supported HDTVFormats
Supported PCResolutions
Video Input Formats

Input Connections

Component Video Input
Analog RGB Input
DVI Input
Power Input

Output Connections

Analog RGB Output
DVIOutput

Scaling Engine

Phase Lock Loops
De-Interlacing
Pull-Down

Control

Front Panel
IR Remote Control

Mechanical

Dimensions (H-W-D)
Weight

Environmental

Storage Temperature
Operating Temperature
Humidity (storage / operating)

Power Requirements

External AC Power Adapter

Regulatory Approvals

Converter / Scaler unit
ACPower Adapter

Warranty

Limited Warranty

Model Number

DVI-3331a

Accessories Included

1x External AC Power Adapter, 1x IR Remote Control Unit, 1x User Guide

Optional Accessories

International AC Power Adapter (with plugs for: USA, Euro, UK, Australia)

DVI v1.0 and HDCP v1.1
165 MHz

1.65 Gbps (single-link)
8-bit
480i, 480p, 576i, 576p, 720p, 1080i and 1080p
Up to 1920x1200
Component Video: YPbPr / YCbCr

3x RCAfemale connectors
HD15 pin (VGA) female connector
DVI 29 pin female connector

5.5 / 2.5 mm locking connector

HD15 pin (VGA) female connector
DVI 29 pin female connector

8-bit, Triple Analog to Digital Converter
3D Motion-Adaptive De-Interlacing with 3D Noise Reduction
3:2 with 2:2 recovery

4x Buttons with On-Screen Display navigation
IR Remote Control with On-Screen Display navigation

1.0” x 7.1” x 5.3” (26.4 mm x 180.0 mm x 135.5 mm)

17.3 oz (490 g)

0° to +50° C (+32° to +122° F)

-10° to +70° C (+14° to +158° F)
10% to 90% (non-condensing)

Input: 100~240VAC / 50-60Hz
Output: 5VDC, 2.0A

FCC, CE, RoHS
FCC, CE, UL, C-UL, CEC, GS, PSE, RoHS

3 Years Parts and Labor

AV-PC-DVI to PC-DVI Converter / Scaler

-3-

2.1 Supported Input Formats and Resolutions

The DVI-3331a accepts digital DVI or HDMI (using an adapter cable), as well
as analog RGB and analog Component Video via separate input connections.
The table below lists the supported input formats and resolutions:

Input Resolution

480i 720x480 60 (NTSC) Interlaced

576i 720x576 50 (PAL) Interlaced

480p 720x480 60 Progressive

576p 720x576 50 Progressive

720p 1280x720 50,60 Progressive

1080p 1920x1080 50,60 Progressive

1080i 1920x1080 50,60 Interlaced

VGA 640x480 60,72,75,85 Progressive

SVGA 800x600 56,60,72,75,85 Progressive

XGA 1024x768 60,70,75,85 Progressive

SXGA 1280x1024 60,75,85 Progressive

UXGA 1600x1200 60 Progressive

WXGA 1280x800 60 Progressive

WSXGA 1680x1050 60 Progressive

WUXGA 1920x1200 60 Progressive

Vertical Rate

(Hz)

Scan

Format

Signal Format /

Connectors

YCbCr via 3x RCA

4-pin mini-DIN

RGB,H,V via HD15 and DVI

YPbPr via 3x RCA

RGB,H,V via DVI

YPbPr via 3x RCA

RGB,H,V via HD15 and DVI

-4-

2.2 Supported Output Formats and Resolutions

The DVI-3331a provides several output resolutions in DVI and RGB,H,V formats:

Output Resolution

480i 720x480 60 Interlaced

576i 720x576 50 Interlaced

480p 720x480 60 Progressive

576p 720x576 50 Progressive

720p 1280x720 50, 60 Progressive

1080i 1920x1080 50, 60 Interlaced

1080p 1920x1080 50, 60 Progressive

VGA 640x480 60 Progressive

SVGA 800x600 60 Progressive

XGA 1024x768 60 Progressive

SXGA 1280x1024 60 Progressive

SXGA+ 1400x1050 60 Progressive

UXGA 1600x1200 60 Progressive

WXGA 1280x800 60 Progressive

WXGA+ 1440x900 60 Progressive

WSXGA 1680x1050 60 Progressive

WUXGA 1920x1200 60 Progressive

Vertical Rate

(Hz)

Scan

Format

Signal Format /

Connectors

RGB,H,V via HD15 and DVI

3.0 PACKAGE CONTENTS

Before attempting to use this unit, please check the packaging and make certain
the following items are contained in the shipping carton:

• 1xDVI-3331aAV-PC-DVItoPC-DVIConverter/Scaler

• 1xExternalACPowerAdapter

• 1xIRRemoteControl

• 1xUserGuide

Note: Please retain the original packing material should the need ever arise to return the unit.
If you nd any items are missing, contact your reseller or DVIGear immediately. Please have
the Model Number, Serial Number, and Invoice Number available for reference when you call.

-5-

4.0 CONNECTING THE HARDWARE

Please study the following front panel and back panel images in order to
become familiar with connector locations and control functions:

1 Component Video Input: supports YPbPr and YCbCr formats

2 Infrared Receiver

3 Status LEDs: indicates selected source type

4 MENU / ENTER: press to access OSD Menus; acts as the enter key for

menu selection

5 Multi-function Keys: see note on page 7

6 Power ON / OFF: press to power the unit on or off

1 DC Power Input: locking female connector for External AC Power Adapter

2 DVI Output: female connector; connect to a compatible DVI or HDMI display

3 PC Output: HD15 pin female; connect to a compatible analog RGB,H,V display

4 DVI Input: female connector; connect to a compatible DVI or HDMI source

5 PC Input: HD15 pin female; connect to a compatible analog RGB,H,V source

-6-

Note: The functions of the “+” and “-” keys change depending on whether or not the OSD
Menus are present. When the OSD Menus are present (activated by pressing the Menu
control button), the “+” and “-” keys allow navigation through the various menu parameters.

When the Menus are not present, the “-” key will automatically adjust the picture centering,
color, etc. for the analog input signals (Component Video or PC). The “+” will sequentially
step through the different inputs of the Converter / Scaler.

This Converter / Scaler uses advanced signal processing that will automatically
accept, identify, and scale a wide array of input formats and resolutions. For best
results, it is usually recommended to set the unit’s output resolution to match the
native resolution of the connected display. Please consult your owner’s manual in
order to determine your display’s native resolution.

When using the DVI-D output signal (digital only), you must use a display or other
destination device that has a compatible DVI or HDMI input. You can connect the
output of this unit to a DVI destination device (e.g. PC display) using a DVI-DVI
cable or to an HDMI destination device (e.g. HDTV display) using a DVI-HDMI
cable. Please consult DVIGear for assistance in cable selection.

Referring to the product images in Section 4, connect the appropriate cables to all
inputs and outputs, taking care to use high quality cables. Note that low quality
cables can cause serious image quality degradation, as well as limit the maximum
possible distance between the Converter / Scaler and the source and destination
devices. Cable selection is especially important for long DVI and HDMI cables
due to the high bit rates of these digital signals. For best results use DVIGear’s
Super High Resolution™ (SHR™) DVI and HDMI cables.

After the cables are connected, connect the supplied AC Power Adapter to the
DVI-3331a. Use only the furnished power adapter to avoid the possibility of
equipment damage.

Plug the AC Power Adapter into the unit and into an AC wall outlet and press the
Power button to activate the unit. Verify that one of the red Status LEDs lights up,
indicating that power has been applied to the unit. Press the Power button to turn
the unit OFF / ON again as needed. In the event of a power outage, this unit will
automatically power ON and restore the last used settings as soon as power is
reapplied to the unit.

Note: This product utilizes a “Twist-Lock” DC power connector to prevent the power cable
from coming loose. Insert the DC plug into the power input jack on the rear panel, then
gently twist the plug a quarter turn in the clockwise direction to lock it in place. To remove
the power connection, simply rotate the DC plug a quarter turn counter-clockwise and then
extract the power cable.

-7-

5.0 OPERATING THE UNIT

Select PC Input

The DVI-3331a can be operated either from the front panel controls or via the
supplied IR Remote Control unit. Since IR is the control method preferred by
most users, please take a moment to familiarize yourself with the location and
function of the control buttons on the IR Remote Control unit.

Toggle through
the Inputs

Select YPbPr
Input

Select Output
Resolution

Exit Menu

Reset to Factory
Default Settings

INPUT POWER

HDMI/DVIHD PC

VGA SVGA XGA

SXGA UXGA 1080i

1080p720p480p

EXIT MENU

OK

RESET

AUTO
ADJUST

Power On/Off

Select DVI Input

Select OSD Menu

Navigate Menus

and Adjustments

Select Auto-Adjust

Function

CR-27*A

Note: Please use the OSD menu for resolutions not directly accessible from the IR remote.

5.1 Using the On-Screen Display Menus

It is important to become familiar with the On-Screen Display (OSD) Menu
structure in order to take full advantage of the capabilities this product has to offer.

5.2 Menu Navigation

Press the MENU / ENTER button to display the OSD menu. Once the menus
are displayed, use the “+” and “-” keys to navigate through the menu structure.
The “+” key will move the curser to the right or down. The “-” key will move the
cursor to the left or up. Once the desired function has been highlighted, press

-8-

the MENU / ENTER key to select the function. Once the function has been
selected, use the “+” and “-” keys to increase or decrease the desired value,
then press the MENU / ENTER key to save the adjustment. To escape the OSD
menus, use the “+” or “-” keys to highlight the EXIT selection, and then press
the MENU / ENTER key, or simply press the MENU / ENTER key repeatedly.

For remote control access, press the MENU key on the IR Remote Control unit
to display the OSD menus. Use the arrow keys to navigate through the OSD
menus. Once the function has been highlighted, press the OK key to select it,
and then use the arrow keys to make the desired adjustment. Press the OK key
to save the adjustment. Press the EXIT key to escape from the OSD menus.

5.2.2 Menu Structure

The OSD Menu structure is as follows:

Video Menu Color Menu Output Menu OSD Menu Info Menu

Contrast User VGA H-Position Project

Brightness Normal SVGA V-Position Input

Hue Warm XGA Time Out Output

Sat Cool SXGA Background Version

Sharpness SXGA+ Exit Date

Picture Mode UXGA

Scale WXGA

NR WXGA+

H-Position (1) WSXGA

V-Position (1) WUXGA

Exit 480i

480p

576i

576p

PC Menu (2)

H-Position (1) 1080i (50/60)

V-Position (1) 1080p (50/60)

Exit Native

720p (50/60)

Note 1: The H-Position and V-Position adjustments are only present when either the
Component Video or PC input signals are selected.

Note 2: The PC menu is only active when the PC input is selected as the source.

-9-

The selection of the Video Menu or PC Menu is made automatically based on
the selected input signal. The Video Menu offers additional functions, including
Picture Mode, Scale and NR (Noise Reduction).

The Picture Mode has four settings: User, Standard, Movie and Vivid. When the
Picture Mode is set to Standard, Movie or Vivid, the Brightness, Contrast, Hue,
Saturation and Sharpness adjustments are set to xed values in order to optimize
the appearance of the image. To change these settings, select User in the Picture
Mode menu. Changes made to these settings will be saved to the unit’s memory
and can be recalled at any time by selecting User in the Picture Mode.

The Scale function has ve user selections: Letterbox, Overscan, Panscan,
Underscan, and Full. The Scale function is used to alter the Aspect Ratio
of the output signal in order to achieve a desired format on the display or
destination device. The following are the menu selections for the Scale
function and their effects:

Letterbox

Overscan

Panscan

Underscan

Full

Remaps the picture content to a letterbox format within the new resolution. Best
used to remap source content from 4:3 aspect ratio to 16:9.

Remaps the picture content larger than the original image in order to reduce the
black bars at the top and bottom of a 16:9 letterbox source.

Remaps the picture content to a smaller size than the output resolution and centers
the content in the middle of the image. Best used to remap source content from
letterbox or 16:9 aspect ratio to 4:3.

Remaps the picture content to a smaller size than the output resolution.

Remaps the picture content to full output resolution. This setting should be used
with high resolution data to maximize clarity.

The NR (Noise Reduction) function has four choices: Low, Middle, High and Off.
For most applications it is recommend that this setting be left in the Off position.

The Color Menu allows selection of four color temperature presets:

Warm

Cool

Normal

User

Picture has a slightly reddish appearance

Picture has a slightly bluish appearance

Picture has a calibrated color temperature

User-denable color temperature

-10-

The Output Menu allows user selection of the desired output resolution. For best
results, it is usually recommended to set the unit’s output resolution to match the
native resolution of the connected display. Please consult your owner’s manual
in order to determine your display’s native resolution. Keep in mind that selecting
an output resolution that is not supported by your display can cause an apparent
malfunction.

The OSD Menu allows you to customize the way the On-Screen Display appears
when it has been accessed.

The Info Menu contains technical information. If you have problems with this unit
and require assistance, a technician may ask you to read information from this
menu as part of the troubleshooting process.

6.0 TROUBLESHOOTING

In the event that the DVI-3331a Converter / Scaler does not appear to be
functioning properly, make certain that the source and all other devices connected
to the unit are functioning correctly by connecting each source device directly
to a compatible display using a short cable. If the signal is present under these
conditions, make certain that power is present to the scaler. Check that all
cables have no signs of damage, are well seated, and are of premium quality
as discussed in Section 4. As a nal step, return the unit to the factory default
settings by pressing the RESET key on the IR Remote Control unit.

If the problem persists after trying the above suggestions, please contact your
dealer for additional assistance. If the dealer’s technical personnel are unable
to assist you, please contact DVIGear via telephone at 1.888.463.9927 (toll-free
for United States and Canada) or 1.770.421.6699. You may contact DVIGear by

e-mail at [e-mail].

-11-

7.0 LIMITED WARRANTY

IMITED WARRANTY – With the exceptions noted in the next paragraph, DVIGear,

L
Inc. warrants to the original purchaser that the products it manufactures or
sells will be free from defects in materials and workmanship for a period of three
(3) years from the date of purchase. Should this product, in DVIGear’s opinion,
prove defective within this warranty period, DVIGear, at its option, will repair or
replace this product without charge. Any defective parts replaced become the
property of DVIGear. This warranty does not apply to those products which
have been damaged due to accident, unauthorized alterations, improper repair,
modications, inadequate maintenance and care, or use in any manner for which
the product was not originally intended.

If repairs are necessary under this warranty policy, the original purchaser must
obtain a Return Authorization Number from DVIGear and return the product,
freight prepaid, to a location designated by DVIGear. After repairs are complete,
the product will be returned, freight prepaid.

LIMITATIONS – All products
lieu of all other warranties for this product, expressed or implied, and is limited to
3 years from the date of purchase. DVIGear assumes no liability to distributors,
resellers, end users, or any third parties for any loss of use, revenue, or profit.

DVIGear makes no other representation of warranty, including, but not limited
to, any implied warranty of merchantability or tness for a particular purpose or
otherwise in respect of any of the products sold. The liability of DVIGear with
respect to any defective products will be limited to the repair or replacement of
such products. In no event shall DVIGear be responsible or liable for any damage
arising from the use of such defective products, whether such damages are direct,
indirect, consequential or otherwise, and whether such damages are incurred by
the reseller, end user, or any third party.

sold are “as is.” The above Limited Warranty is in

8.0 REGULATORY COMPLIANCE

This product is compliant with appropriate FCC, CE and RoHS rules and
regulations. The supplied AC Power Adapter is compliant with FCC, CE, UL,

C-UL, CEC, GS, PSE and RoHS rules and regulations.

-12-

Your Digital Connectivity Experts

Toll Free 888.463.9927
Phone [phone]
Fax [phone]

www.dvigear.com

DVI-3331a-UG-03 / July.2012

DVIGear, Inc.
1059 Triad Court, Suite 8
Marietta, Georgia 30062-2258