Dustless Dustie User Manual
Installation Instruction
FOR RIGHT ANGLE GRINDERS
Includes:
• Dustie™ shroud
• Band clamp
• Releasable zip tie
1. UN-PLUG GRINDER. Slip shroud
on grinder, flanges should be flush
with attachment.
4. Tighten band clamp.
2. Cut flanges to adjust height of shroud.
For best dust control, grinding wheel
should be 1/4 inch below shroud.
5. Install Grinding wheel. For best dust
control, wheel should be 1/4 inch
below shroud.
Instructions for Crack Chasing/Tuckpointing Application
1. Trim Flanges to adjust cutting wheel in middle of shroud.
2. Cut the Dustie on "CC Line" or "TP Line" depending on your
desired opening angle. Follow instructions 2-7 above.
3. Snap on Cover Plate* over open face.
*Not Included with all kits
3. Install grinding wheel. See #2
for height.
6. Insert hose to port.
7. Secure other end of hose to the electric cord with
releaseable tie provided.
WARNING
Always make sure grinder is UNPLUGGED when removing
or attaching front noseclip. Before use, refer to your tool
manual for warnings and instructions.
This product was inspected and packaged carefully before being
shipped from the factory. If you should happen to need assistance
during assembly or operation, call 1-800-568-3949 for our
customer service department.
800.568.3949
dustlesstechnologies.com
OM013_0713
Kit # 16500 Includes:
Kit #16500 Includes:
1 - 16006 HEPA Wet/Dry Vacuum
1 - 16006 HEPA Wet/Dry Vacuum
1 - 13141 Micro Pre Filters (2 pkg)
1 - 13141 Micro Pre Filters (2 pkg)
1 - 13242 HEPA Floor Tool
1 - 13242 HEPA Floor Tool
1 - 61000 ChipBuddie
1 - 60001 ChipBuddie
1 - D1836 5" Dustie
1 - D1836 5” Dustie
1 - D5160 6' Adapter Hose
1 - D5160 6’ Adapter Hose
DUSTLESSTMEPA Lead-Safe
Compliance Kit
D1836 Dustie
D1836 Dustie
16006 HEPA Vacuum
16006 HEPA Vacuum
61000 ChipBuddie
60001 ChipBuddie
D5160 6’
D5160 6'
Adapter Hose
Adapter Hose
13242 HEPA
13242 HEPA
Floor Tool
Floor Tool
13141 Micro Pre Filters
Assembly - To install the legs and
accessory tray, undo the clips holding the intermediate cover in place
and set the cover and lid assembly
aside. Turn tank upside down. Front
legs are on either side of the drain
port opening. These front legs do
not have the small hooks on either
side. The back legs do have the
hooks. These hooks are for the
hose to rest on when in storage.
Align legs with openings provided
on bottom of the canister and slide
into place. The holes will only align
in proper position for front and back
legs. Insert black support screw
HEPA Vacuum - C
owners manual enclosed
with vacuum.
HEPA Floor Tool The HEPA Floor Tool
features a beater bar
as specified by EPA
to meet renovation
contractor certification
requirements. Fit
easily into HEPA
Vacuum attachments.
For a complete version of all owner’s manuals, please visits www.dustlesstools.com <http://www.dustlesstools.com> or call 800 568-3949.
omplete
into hole and tighten screw with a
Phillips screwdriver.
Turn cleaner tank right side up.
ChipBuddie - Hook it to a hose
with the 6’ hose adaptor and
scrape. Change blade by using a
Philips screwdriver. Works on
both sides of the blade for
collecting debris in both
directions. Use for scraping
paint or popcorn ceilings.
Adapter Hose -
Attaches easily to
HEPA Vacuum hose.
13141 Micro Pre Filters
Attach Accessory Tray
Align the three slots on the edge of
the accessory tray with the three
guides on the rear side of the tank
and press the accessory tray toward
the tank as you push the tray down.
The two locking tabs will slide
under the rim of the tank and catch.
By pushing the tray down and
toward the tank it will lock into
place.
Place intermediate cover and lid
assembly right side up and set
on top of the tank. Attach the
yellow clips from the tank onto
the intermediate cover.
The Lid Assembly with the vacuum
controls, motor, and filters are all
preassembled at the factory for your
Micro Pre-filter To install the Micro
Pre-filter, flip back
the lid tabs and
remove the lid.
Put the Micro Prefilter inside the
canister and slide
the opening of the
cardboard mounting collar over the input port on the inside
of the canister. Press firmly around all edges to ensure a
snug fit and air tight seal. Spread the Micro Pre-filter out,
making sure no part of it gets trapped under the edge of the
lid. Reinstall the lid and flip the locking tabs back
to the down position.
Kit Model 16500
Kit Model 16500
convenience. Maintenance and
replacement of filters is described
later in this manual.
Attach hose, wands and
cleaning accessories
Hose and accessories are stored
on the unit. The hose will loop
through the two outside holes of the
accessory tray and rest on the hooks
of the back legs as shown below.
For convenience, additional
accessories can be stored on
tray when not in use.
To Use Accessories
Push hose into tank port; twist hose to
tighten or loosen connection. The
wands and cleaning accessories
attach to hose in the same manner.
Loading...