
Switch on
Sewing mode
Quick Reference Card 745-35S
P+F
Setting programs
F
short
F
long
ESC
ESC
ESC
ESC
+
Sequence on/off
Sequence new create
+
Displaying the counter of pieces/Deleting
-
+
Center knife on/off
+
+
CRUQHr knife on/off
+
Stacker on/off
-
or
Changing the current seam length
301 Indicating/Deleting
302 Setting the bobbin thread counter
303 Testing the feeding process
304 Step by step mode
305 Dongle menu
or
Changing over to the next seam program
© Dürkopp Adler AG 0791 745400 EN - 0.0 - 0/201

Quick Reference Card 745-35S
KW-barrier
fl ap size; Sosition the fl ap correctly
Alter L1 (adjust corner knife distance) or change
For cancelling the pedal has be actuated once again.
Afterwards the feeding clamp runs in ist rear position.
Correct folder adjustment
(mechanical collision; check switch S8)
Correct folder adjustment
(mechanical collision; check switch S8)
positioning point of the current seam
6ZLQJLQFRUQHUNQLIHVWDWLRQ
Check/adjust fastening of the coUner knife station
Sewing folding station in
Check/adjust fastening of the folding station
Change the present seam length, or change the loading
position, or change L1 (adjust distance counter knife).
Kt-barrier (S4) for fabric removal inactive Adjust light-barrier (S4) for fabric removal
Pedal has been stepped back during the sewing process
Error/Info Description Remedy
3210 Thread breakage Thread in the thread again
3215 Empty bobbin (Bobin thread counter) Insert a full bobbin
3220 Empty bobbin (Remaining thread-monitor)
9601
Folder not in top position
Folder not in low position
Error when scanning the fl ap by ligKW-barrier Check the refl ecting foil; check aligment of the lig
9604 Folder not in top position Lig
9700
9701
9721 Flap has been pos. in front of the front positioning point Position the fl ap correctly
9720
9722 Flap protrudes from the max. sewing area (behind the rear positioning point) Check the
9723 Fluff at the fl ap beginning Feed fl aps with smooth edges; check the refl ecting foil
Corner knife at the seam beginning cannot be driven to
Corner knife station is swung out
Folding station is swung out during the sewing process
Step back on the pedal; afterwards the transport carriage runs to the back;
start the process.
Folding station is swung out
Folding station is swung out during the sewing process
Step back on the pedal; afterwards the transport carriage runs to the back;
start the process
9730
9726 Flap too large or refl ecting foil soiled or defective Check fl ap size and refl ecting foil
9001
9002
9003 Wrong needle position before sewing start Turn manually the hand wheel in lever up position
Corner knife at the seam beginning cannot be reached
ref Request to carry out the reference run after switching the machine on. Step back on the pedal
Current
seam length
fl ashes
© Dürkopp Adler AG 0791 745400 EN - 01.0 - 04/2016

Quick Reference Card 745-35S
Switch on
Sewing mode
P
Editing the current seam parameters
100 Seam length mm
101 Stacker on/off
102 Center knife on/off
103 Center knife correction seam beginning 1/10 mm
104 Center knife correction seam end 1/10 mm
105 Corner knife on/off
106 Corner knife correction seam beginning 1/10 mm
107 Corner knife correction seam end 1/10mm
108 Stitch length 1/10 mm
109 Sewing motor speed
110 Sewing motor soft start on/off
111 Sewing motor number of soft start stitches
112 Sewing motor soft start speed
113 Clamping mode
0 = Lower left and right feeding clamp simultaneously
1 = Lower left feeding clamp fi rst
2 = Lower right feeding clamp fi rst
114 Positioning point
0 = front
1 = center
2 = rear
115 Positioning point offset mm
116 Type seam tightening seam beginning
0 = Bartack
1 = Condensed stitches
117 Number of condensed stitches seam beginning
118 Stitch length condensed stitches/Bartack Seam beginning 1/10 mm
119 Number of bartacks seam beginning
120 Type seam tightening seam end
0 = Bartack
1 = Condensed stitches
121 Number of condensed stitches seam end
122 Stitch length condensed stitches/Bartack Seam end 1/10 mm
123 Number of bartacks seam end
124 Material feed type,
0 = Material runs to the loading position
1 = Material runs to the stacking position
2 = no run, in stacking position,
125 Type of waiting position
0 = Feeding clamp runs to the waiting position
1 = Feeding clamp remains in stacking position
126 Material feed to the stacking position
© Dürkopp Adler AG 0791 745400 EN - 01.0 - 04/2016

Quick Reference Card 745-35S
Switch on
Sewing mode
P
Editing the current seam parameters
127 Loading speed
128 Return speed
129 Downholder on/off
130 Sewing mode
0 = Constant sewing length
1 = Light-barrier for fl ap scanning
131 Light-barrier correction seam beginning 1/10 mm
132 Light-barrier correction seam end 1/10 mm
133 Material feed to the waiting position
134 Max. Flap length
135 Flap clamp on/off
136 Pedal mode
0 = normal
1 = Pedal has to be in basic position before the next step
2 = Pedal actuation for moving in sewing position (fl ap clamp)
137 Second light barrier active
0 = 1st light barrier active
1 = 2nd light barrier active
© Dürkopp Adler AG 0791 745400 EN - 01.0 - 04/2016