DURKOPP ADLER 581 Additional Instructions

581

Additional Instructions

Fitting the sewing lamp

IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE

All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,

cluding extracts, is prohibited without the written approval in advance of Dürkopp Adler AG.

in
Copyright © Dürkopp Adler AG 2015

Table of Contents

1 Components in the parts set.....................................................3

2 Fitting the sewing lamp.............................................................. 4

2.1 Removing components.................................................................5

2.2 Fitting the housing with printed circuit board................................ 7

Additional Instructions 581 - 00.0 -02/2015 1

Table of Contents

2 Additional Instructions 581 - 00.0 -02/2015

Components in the parts set

1 Components in the parts set

The parts set 0580 101644 is intended for class 581 machines.
Before fitting, check that the scope of delivery of the parts set is correct.

0791 581716 EN 1 Additional instructions

Fig. 1: Parts set

Part no. Quantity Designation

0580 101610 1 Housing
9352 000020 6 Clamping disk
9850 580007 1 Printed circuit board

Additional Instructions 581 - 00.0 - 02/2015 3

Fitting the sewing lamp

2 Fitting the sewing lamp

WARNING

Risk of electric shock from live parts!

Dangerous injuries to life and limb possible.
The sewing light may only be fitted by qualified

specialists.
Switch off the machine and unplug the power plug.
Make sure the power plug cannot be

u

nintentionally reinserted.

In order to be able to fit the parts set, you must remove the existing
components.

When doing so, comply with the following

Sequence:

1. Remove the clamping plates.

2. Remove the finger protection.

3. Detach the housing.

4. Detach the head cover.

5. Remove the head cover.

6. Remove the housing.
Now you can fit the new housing with the

printed circuit board.

4 Additional Instructions 581 - 00.0 - 02/2015

Fitting the sewing lamp

②

①

④

③

2.1 Removing components

A description of how to remove the clamping plates is provided in the
 Operating Instructions.

To remove the other components:

Step

1. Remove the screws (2).

2. Remove the finger protection (1).

Fig. 2: Removing the finger protection

(1) - Finger protection (2) - Screws

3. Remove 3 screws (3) (width across flats 3) from the housing for the
drive belts (4).

Fig. 3: Detaching the housing

(3) - Screws (4) - Housing

Additional Instructions 581 - 00.0 - 02/2015 5

4. Loosen the screws on the head cover (5).

⑤

5. Remove the head cover (5).

6. Remove the housing for the drive belts (4).

Fig. 4: Removing the head cover

Fitting the sewing lamp

(5) - Head cover

6 Additional Instructions 581 - 00.0 - 02/2015

Fitting the sewing lamp

①

②

③

2.2 Fitting the housing with printed circuit board

Step

1. Place the housing (1) with preassembled printed circuit board under

Fig. 5: Housing with printed circuit board

the sewing

head.

(1) - Housing (2) - Printed circuit board

2. Connect the X411 cable (3) to the tab connector of the printed circuit
board (2).

Fig. 6: Connecting the cable

(3) - X411 cable

3. Secure the housing with the 3 screws ( 2.1 Removing componen ts,
pg. 5).

Additional Instructions 581 - 00.0 - 02/2015 7

4. Retighten the head cover.

5. Fit the finger protection.

Fitting the sewing lamp

6. Insert the clamping plates (see

 Operating Instructions).

8 Additional Instructions 581 - 00.0 - 02/2015

DÜRKOPP ADLER AG
Potsdamer Str. 190
33719 Bielefeld
Germany
Phone: [phone]
E-mail: [e-mail]
www.duerkopp-adler.com

Subject to design changes - Part of the machines shown with additional equipment - Printed in Germany

© Dürkopp Adler AG - Additional Instructions - 0791 581716 EN - 00.0 - 02/2015