EN-1
EN-2
Table of Contents
PRODUCT OVERVIEW .............................................................. 3
FRONT VIEW .............................................................................................. 3
LEFT VIEW ................................................................................................ 4
BACK VIEW ............................................................................................... 5
FUNCTION BUTTON DEFINITIONS .......................................... 6
PIN ASSIGNMENTS ..................................................................... 8
V10BBT1 User’s Manual
EN-3
Product Overview
This section describes the main components of your device.
Front View
No.
Item
Description
1 Power LED
Indicate the power and heater status:
• Green: the system is running (active).
• Red: the heater is on before the system booting
complete.
• Orange: the heater is on while the system is
active.
• Off: the system is off.
• Green (flashing): the system is suspending to
RAM.
V10BBT1 User’s Manual
EN-4
No.
Item
Description
2 Programmable LED
(Warning LED)
Indicate the device status (user define).
3 Function buttons Refer to the “Function Button Definitions” section
on page 6~7.
4 Brightness buttons Press +/- to adjust the brightness level.
5 Power button Press to turn the device on/off.
6 Display screen Allow users to use the Resistive Single Touch.
Left and Right Views
No.
Item
Description
1
Corner mounting
holes
Attach the corner mount bracket (Thread type:
M5x0.8P, Length: 15mm, Quantity: 4-on the left
and right sides).
2 SSD door Loosen the thumbscrew to open the SSD door, and
then remove the SSD.
V10BBT1 User’s Manual
EN-5
Back View
No.
Item
Description
1
Corner mounting holes
Attach the corner mount bracket (Thread type:
M5x0.8P, Length: 15mm, Quantity: 4-on the
back side).
2
Grounding receptacles
Install the ground screw/wire to ensure proper
grounding connection (Thread type: M6x1P,
Length: 14mm, Quantity: 2).
3 VESA mounting holes Attach the VESA mount bracket (Thread type:
M4x0.7P, Length: 8mm, Quantity: 8).
Note: Support VESA mounting hole pattern of
75x75mm or 100x100mm.
4
Amphenol connectors
Refer to the “Pin Assignments” section on page
8~11.
V10BBT1 User’s Manual
EN-6
Function Button
Definitions
The Function buttons work similar as any regular keyboard, with a few differences.
To learn more about its respective function, refer to the table below:
Button
Description
F1
Press to emulate the F1 key.
F2
Press to emulate the F2 key.
F3
Press to emulate the F3 key.
F4
Press to emulate the F4 key.
F5
Press to emulate the F5 ke y.
F6
Press to emulate the F6 ke y.
F7
Press to emulate the F7 ke y.
F8
Press to emulate the F8 ke y.
F9
Press to emulate the F9 ke y.
F10
Press to emulate the F10 key.
F11
Press to emulate the F11 key.
F12
Press to emulate the F12 key.
F13
Press to emulate the Win ( ) ke y.
F14
Press to emulate the Delete key.
F15
Press to emulate the Esc key.
F16
Press to emulate the Enter ke y.
F17
Press to emulate the + key.
F18
Press to emulate the - key.
F19
Press to turn on/off all function buttons (F1~F28) backlight.
F20
Press to enable/disable Night Vision mode (In Night Vision mode, LCD
brightness is ≦1.7nits and all indicators and buttons LED are off).
F21
Press to emulate the (left arrow) key.
V10BBT1 User’s Manual
EN-7
Button
Description
F22
Press to emulate the (right arrow) ke y.
F23
Press to emulate the (up arrow) key.
F24
Press to emulate the (down arrow) key.
F25
Press to emulate the Home ke y.
F26
Press to emulate the End key.
F27
Press to emulate the PageUp key.
F28
Press to emulate the PageDown ke y.
V10BBT1 User’s Manual
EN-8
Pin Assignments
Amphenol connector pins numbering
Connector
V10BB System Connector
Part No.
Mating Connector Part No.
(Customer)
J1 AMPHENOL PT02A-18-32P AMPHENOL PT06A-18-32S
J2 AMPHENOL PT02A-18-32PW AMPHENOL PT06A-18-32SW
J3 AMPHENOL PT02A-18-32PX AMPHENOL PT06A-18-32SX
J4 AMPHENOL PT02A-18-32PY AMPHENOL PT06A-18-32SY
J5 AMPHENOL PT02A-18-32PZ AMPHENOL PT06A-18-32SZ
J6 AMPHENOL PT02A-10-5P AMPHENOL PT06A-10-5S
Note: COM mode can be configured according to customer’s requirement
(Factory option). The default setting is RS232.
V10BBT1 User’s Manual
EN-9
Refer to the table below for the pinout with their relevant functions of Amphenol
connectors.
J1 : PT02A-18-32P J2 : PT02A-18-32PW
Pin No. Signal Function Pin No. Signal Function
A DVI_VGA_RED
VGA
A USB3_VCC5
USB3
B DVI_VGA_GREEN
B USB3_PN
C DVI_VGA_BLUE
C USB3_PP
D DVI_VGA_GND
D USB3_GND
E DVI_VGA_HSYNC
E USB2_VCC5
USB2
F DVI_VGA_VSYNC
F USB2_PN
G DVI_CON_DDC_CLK
G USB2_PP
H DVI_CON_DDC_DAT
H USB2_GND
J VCC5_DVI
DVI-D
J USB0_VCC5
USB0
K DVI_DATA2
K USB0_PN
L DVI_DATA2#
L USB0_PP
M DVI_GND
M USB0_GND
N DVI_DATA1
N USB1_VCC5
USB1
P DVI_DATA1#
P USB1_PN
R DVI_GND
R USB1_PP
S DVI_DATA0
S USB1_GND
T DVI_DATA0#
T GLAN1_MX0+
GLAN1
U DVI_GND
U GLAN1_MX0-
V DVI_CLK
V GLAN1_MX1+
W DVI_CLK#
W GLAN1_MX1-
X DVI_GND
X GLAN1_MX2+
Y DVI_HPD
Y GLAN1_MX2-
Z DVI_DDC_DAT
Z GLAN1_MX3+
a DVI_DDC_CLK
a GLAN1_MX3-
b PAL1-
PAL1
b GLAN2_MX0+
GLAN2
c PAL1+
c GLAN2_MX0-
d PAL2-
PAL2
d GLAN2_MX1+
e PAL2+
e GLAN2_MX1-
f PAL3-
PAL3
f GLAN2_MX2+
g PAL3+
g GLAN2_MX2-
h PAL4-
PAL4
h GLAN2_MX3+
j PAL4+
j GLAN2_MX3-
V10BBT1 User’s Manual
EN-10
J3 : PT02A-18-32PX
J4 : PT02A-18-32PY
Pin
No.
Signal
Function
Pin
No.
Signal
Function
RS-232 RS-485 RS-422
RS-232 RS-485 RS-422
A COM1_GND GND GND
COM1
A COM4_GND GND GND
COM4
B COM1_RI#
B COM4_RI#
C COM1_DTR# TX-
C COM4_DTR# TX-
D COM1_CTS#
D COM4_CTS#
E COM1_SOUT TX+
E COM4_SOUT TX+
F COM1_RTS#
F COM4_RTS#
G COM1_SIN D+ (A) RX+
G COM4_SIN D+ (A) RX+
H COM1_DSR#
H COM4_DSR#
J COM1_DCD# D- (B) RX-
J COM4_DCD# D- (B) RX-
K COM2_GND GND GND
COM2
K COM5_GND GND GND
COM5
L COM2_RI#
L COM5_RI#
M COM2_DTR# TX-
M COM5_DTR# TX-
N COM2_CTS#
N COM5_CTS#
P COM2_SOUT TX+
P COM5_SOUT TX+
R COM2_RTS#
R COM5_RTS#
S COM2_SIN D+ (A) RX+
S COM5_SIN D+ (A) RX+
T COM2_DSR#
T COM5_DSR#
U COM2_DCD# D- (B) RX-
U COM5_DCD# D- (B) RX-
V COM3_GND GND GND
COM3
V COM6_GND GND GND
COM6
W COM3_RI#
W COM6_RI#
X COM3_DTR# TX-
X COM6_DTR# TX-
Y COM3_CTS#
Y COM6_CTS#
Z COM3_SOUT TX+
Z COM6_SOUT TX+
a COM3_RTS#
a COM6_RTS#
b COM3_SIN D+ (A) RX+
b COM6_SIN D+ (A) RX+
c COM3_DSR#
c COM6_DSR#
d COM3_DCD# D- (B) RX-
d COM6_DCD# D- (B) RX-
e
e
f
f
g
g
h
h
j
j
V10BBT1 User’s Manual
EN-11
J5 : PT02A-18-32PZ
J5 : PT02A-18-32PZ
Pin
No.
Signal
Function
Pin
No.
Signal
Function
RS-232 RS-485 RS-422
RS-232 RS-485 RS-422
A COM7_GND GND GND
COM7
U EXT_GPI0
EXT GPI
B COM7_RI#
V EXT_GPI1
C COM7_DTR# TX-
W EXT_GPI2
D COM7_CTS#
X EXT_GPI3
E COM7_SOUT TX+
Y EXT_GPO0
EXT GPO
F COM7_RTS#
Z EXT_GPO1
G COM7_SIN D+ (A) RX+
a EXT_GPO2
H COM7_DSR#
b EXT_GPO3
J COM7_DCD# D- (B) RX-
c EXT_GPIO_GND
EXT
GPI/O
K CB1_VBAT
CANBUS1
d AUDIO_GND1
AUDIO
L CB1_J1939+
e AUDIO_GND2
M CB1_J1939-
f LINE_OUT
N CB1_GND
g LINE_IN
P CB2_VBAT
CANBUS2
h MIC_IN
R CB2_J1939+
j AUDIO_GND3
S CB2_J1939-
T CB1_GND
J6 : PT02A-10-5P
Pin No. Signal
A VCC24-
B
VCC24-
C VCC24+
D VCC24+
E ACC
Power Cable Connection with ACC Control: Power Cable Connection without ACC Control:
Note: ACC power on function can be configured according to customer’s
requirement (Factory option).
Loading...