Store this manual so that it can be retrieved whenever needed.
Instruction Manual
DP-22S/22L/24S
Ver.1
Correct operation and periodic maintenance are
essential for ensuring safe use of this machine.
Thoroughly read this manual before using this
machine.
DUPLO CORPORATION
1
2
1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Thank you for your purchase of the Duprinter DP-22S/22L/24S.
To ensure safe and efficient prolonged use of this machine, read and thoroughly understand this manual before
using this machine. After using this manual, be sure to keep it in a place to handy reference.
Introduction
PLEASE NOTE
In the interest of upgrading our products, specifications and other data given in this manual are subject to
change without notice. If the manual contains anything that you do not understand, contact the manufacturer for clarification.
2
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The following is a quick reference to the functions of the DP-22S/22L/24S printer.
B4 Printout
B5 Printout
A4 Document
Enlargement/Reduction ........
(a P.39)
This function copies a document on one standard paper size to another larger or smaller standard paper size.
94% Reduction .......
(a P.40)
This function slightly reduces the size of a document when printing to the same standard paper size as the document.
A4 Document A4 Printout
(94%)
Function Quick Reference
1%-Step Enlargement and Reduction .........
(a P.42)
This function enlarges or reduces a document in 1% steps between 50% and 200%.
Document
Printout
3
2
1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Text/Photograph/Text and Photograph Mode .........
(a P.47)
This function selects the optimum print quality to match the document.
ABCDEFGH
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
tuvwxyz
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
tuvwxyz
ABCDEFGHIJKLNO
PQRSTUVWXYZ
ABCDEFGH
ABCDEFGHIJKLNO
PQRSTUVWXYZ
abcdefghijklmnopqrs
Text
Text/Photograph
Photograph
Book Shadow Eraser Mode .........
(a P.63)
This function erases the shadows on the center or edges of book or other folded documents when printing the open
spread.
Document
Printout
Printout
With shadow eraser
Without shadow eraser
Printout
Document
2-up Function .........
(a P.58)
This function prints 2 images of a document on one page.
4
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Sectional Printing ........
(a P.67)
You can print the specified number of sets of copies in each set.
1
1
1
1
1
1
1
1
Document
1st set
5 copies x 2 sets
2nd set
3 copies x 4 sets
3rd set
2 copies x 5 sets
1
1 1 1
Changing Print Quantity per Document .........
(a P.71)
This function changes the number of prints made from each document.
2
2
2
3
2
3
3
3
3
1
Documents
1
1
3
1st document
5 copies x 2 sets
2nd document
3 copies x 4 sets
3rd document
2 copies x 5 sets
2
2-in-1 Layout
Available only with ADF installed
.........
(a P.61)
This function prints two different documents on one page.
Documents
Printout
5
2
1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Contents
Introduction......................................................................................................................... 1
Function Quick Reference ................................................................................................. 2
Notes on Safety (Please Read and Observe) ................................................................... 8
Safety Precautions .............................................................................................. 8
Warning Sticker ........................................................................................................ 11
Positioning the Machine ........................................................................................... 12
Maintenance............................................................................................................. 13
Printing and Duplicating Cautions ............................................................................ 14
Conventions Used in This Manual............................................................................ 15
Chapter 1 Before Using This Machine
System Setup.................................................................................................................... 18
Part Names and Their Functions..................................................................................... 19
Printer Appearance .................................................................................................. 19
Control Panel............................................................................................................ 22
LCD Panel ................................................................................................................ 24
T urning Power ON/OFF .................................................................................................... 25
Turning ON Printer Power......................................................................................... 25
Turning OFF Printer Power....................................................................................... 26
Standard Mode......................................................................................................... 26
Key Card Counter [Available only with Key Card Counter installed]......................... 27
Document/Printing Paper Specification ......................................................................... 28
Acceptable Documents ............................................................................................ 28
Acceptable Printing Paper ........................................................................................ 28
How Platemaking and Printing is Performed ................................................................. 29
Platemaking.............................................................................................................. 29
Printing ..................................................................................................................... 29
Chapter 2 Printing Using Basic Functions
Basic Printmaking ............................................................................................................ 32
Loading and Replacing Paper ......................................................................................... 34
Loading Paper .......................................................................................................... 34
Adjusting Paper Feed Pressure................................................................................ 35
Loading Documents ......................................................................................................... 36
Positioning the Document......................................................................................... 36
Loading Document on Document Glass Plate ......................................................... 37
Loading Document in ADF [Available only when ADF installed] .............................. 38
Enlargement and Reduction............................................................................................ 39
Enlarging/Reducing from Standard-Size Document to Standard-Size Paper .......... 39
94% Reduction ......................................................................................................... 40
1% - Step Enlargement and Reduction .................................................................... 42
Selecting Printing Paper Size .......................................................................................... 44
Text/Photograph/Text and Photograph Mode ................................................................ 47
Print Output....................................................................................................................... 49
Installing Print Tray ................................................................................................... 49
Truing up Printed Pages........................................................................................... 51
6
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Contents
Chapter 3 Printing With V arious Function
Saving Settings................................................................................................................. 54
Saving Settings ........................................................................................................ 54
Retrieving Settings ................................................................................................... 56
Multiple Printing on One Page......................................................................................... 58
2-up Function ........................................................................................................... 58
2-in-1 Layout [Available only when ADF installed].................................................... 61
Book Shadow Eraser Mode ............................................................................................. 63
Adjusting Plate Darkness ................................................................................................ 65
Sectional Printing ............................................................................................................. 67
Sectional Printing ..................................................................................................... 67
Sectional Printing (changing print quantity per document)....................................... 71
Dividing Sections with Tape [Available only with Tape Cluster Device]..................... 74
Chapter 4 Miscellaneous Functions
Confidential Safeguard Function .................................................................................... 78
Total Counter Display Function....................................................................................... 79
Print Speed Adjustment Function................................................................................... 80
Printing Position Adjustment Function.......................................................................... 81
On-Line Print Function [Available Only With Interface Kit Installed]........................... 82
Chapter 5 Replacing Consumables
Replacing the Ink Pack..................................................................................................... 84
Replacing the Master Roll................................................................................................ 87
Replacing the Master Ejection Core ............................................................................... 90
Replacing the Drum Unit.................................................................................................. 92
Removing the Drum Unit .......................................................................................... 92
Installing the Drum Unit ............................................................................................ 94
Chapter 6 Troubleshooting
Countermeasures to Troubles......................................................................................... 98
Power Does Not Turn ON......................................................................................... 98
Platemaking/Printing is Not Possible........................................................................ 98
Error Messages................................................................................................................. 99
Supplying or Changing Paper While Printing.............................................................. 103
If Paper Runs Out During Printing.......................................................................... 103
Adding Paper While Printing .................................................................................. 103
Changing Paper Selection While Printing .............................................................. 105
Paper Jams ..................................................................................................................... 107
When “PAPER LEFT JAM” is Displayed (Feed Tray)............................................. 107
When “PAPER RIGHT JAM” is Displayed (Print Tray) ........................................... 108
When “MAST. EJECT ERROR” is Displayed.................................................................111
When “MASTER SET MISS” is Displayed .................................................................... 114
7
2
1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Contents
Chapter 7 Specifications and Maintenance
Specifications ................................................................................................................. 118
Appendix
Index ................................................................................................................................ 122
Quick Operation Guide .................................................................................................. 124
8
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Notes on Safety (Please Read and Observe)
Safety Precautions
Various symbols and pictures are used in this manual and on the stickers affixed to the machine. These symbols and
pictures provide warnings and instructions to prevent danger to you or other personnel, and to prevent damage to office
property. The meanings of these symbols and pictures are explained below.
WARNING
Indicates a high degree of potential danger. If the warning is ignored, death or serious
injury may result.
CAUTION
Indicates a medium degree of potential danger. If the caution is ignored, medium injury or
damage to property may result.
[Examples of Pictorial Symbols]
A circle with a line through it indicates a prohibited action. The particular act prohib-
ited is indicated by a picture inside the circle. (In the example shown here, the prohibited
act is disassembly.)
A black disc indicates an instruction, or sometimes a prohibited action. T he instruction
itself is indicated by pictorial symbols drawn in white on the disc. (In the example shown
here, the instruction is “Remove the plug from the outlet.”)
• These are particularly important safety points and should always be observed.
W ARNING
If the machine is used after foreign matter (metal fragments, water, or liquid) has entered the
machine, this may result in fire or electric shock.
• Turn the main unit’s power switch OFF, and then remove the power plug from the outlet. Contact
the sales distributor.
If the machine is used after heat, smoke, strange smell, or other abnormality is detected, this may
result in fire or electric shock.
• Turn the main unit’s power switch OFF, and then remove the power plug from the outlet. Contact
the sales distributor.
Use only the power cord that is provided among the accessories.
9
2
1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Notes on Safety (Please Read and Observe)
WARNING
Do not modify the machine.
• Doing so may result in fire or electric shock.
Do not remove the rear lid, cabinet, or covers from the machine.
• The inside of the machine contains high-voltage parts, which may cause electric shock.
Do not remove or insert the power plug with wet hands.
• Doing so may result in electric shock.
Do not damage, break, or modify the power cord.
• Do not place heavy objects on, tug, or unnecessarily bend the power cord. Doing so may result in
fire or electric shock.
Do not insert or drop metal, flammable material, or other matter through the ventilation holes into
the machine interior.
• Doing so may result in fire or electric shock.
Do not place flower vases, flowerpots, cups, or water containers (including metal containers) on top
of the machine.
• Fire or electric shock may result if liquid spills inside the machine.
Do not use a source voltage other than that specified. Do not connect two or more loads to a single
outlet.
• Doing so may result in fire or electric shock.
Do not place the machine in a humid or dusty area.
• Doing so may result in fire or electric shock.
10
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Notes on Safety (Please Read and Observe)
CAUTION
Before moving the machine, remove the power plug from the outlet.
• If the cord is damaged, this may result in fire or electric shock.
Remove the power plug itself, not the cord.
• Tugging the cord may damage it (expose conductors, or cause disconnections, etc.), resulting in
fire or electric shock.
Do not place the machine in an unstable position, such as on an unsteady support or sloping area.
• If the machine is dropped or falls over, this could result in personal injury.
Once the machine is in position, secure in place using the casters.
• If the machine falls over, this could result in personal injury.
11
2
1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
L5-T3020
Do NOT touch the drum or rollers
when you operate the jog switch.
Do NOT put hands Inside
machine while it is operatung.
Hands could get caught up
or crushed.
WARNING
Notes on Safety (Please Read and Observe)
Warning Sticker
Keep the WARNING stickers clean at all times. If stickers become damaged or come off, replace them with new ones.
No. Parts No. Name Q’ty
q L1-T3060 Warning Sticker 1 1
w L5-T3020 Warning Sticker 2 1
L1-T3060
WARNING
● Do not remove this cover. The inside of the printer contains movable cutting instruments,
contact with which could result in injury.
12
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Positioning the Machine
Installing the machine on a flat, stable surface.
Avoid installing the machine in a dusty area.
Avoid installing the machine in the direct sunlight or heat,
such as near a stove. Ink may deteriorate and may cause
bad prints, while the machine may indicate errors due to
overheating caused by sunlight. Also avoid hot, cold, or
humid areas since paper may absorb moisture, causing
paper jams or wrinkles.
Notes on Safety (Please Read and Observe)
,
13
2
1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Maintenance
Clean the exterior of the machine as described below.
Tightly wring a soft cloth that has been moistened with
water or neutral detergent, and wipe dirt from the machine’s surface.
Never use alcohol or organic solvents. Doing so may
discolor or damage the machine exterior.
Dust and clean the machine at least once a week to avoid
breakdowns.
Before cleaning, turn the power switch OFF, and then
remove the power plug from the outlet.
To clean the reader glass, use a dry, soft cloth and lightly
wipe off any dirt.
WARNING
• Before cleaning, remove the power plug from the outlet.
Doing so may result in fire or electric shock.
• Prevent water and neutral cleansers from getting inside the machine. If liquids spill inside the machine, contact your agent immediately. Using the machine with water spilled inside may result in fire or
electric shock.
Notes on Safety (Please Read and Observe)
14
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Notes on Safety (Please Read and Observe)
Printing and Duplicating Cautions
There are restrictions on what you may print on this printer. Please be aware that there are some printed materials that
are illegal even to possess.
1. Printed Matter Banned by Law
• Paper money, currency, government bonds and national and local bonds cannot be duplicated, even if they are
stamped with the “sample” seal.
• Paper money, currency and bonds, etc. that are valid in a foreign country cannot be duplicated.
• Unused postage stamps and postcards cannot be duplicated without government consent.
• Government-issued papers pertaining to stamps, liquor and sales tax laws cannot be duplicated.
2. Printed Matter that Require Caution
• Printed-issued securities (stocks, bills and checks, etc.), passes and tickets require caution in duplicating unless a
business is duplicating them for required number for their own business needs.
• Government-issued passports, public- and private-issued driver’s licenses, permits, IDs, passes, food stamps, etc.
require caution in duplicating.
3. Copyrighted Materials
Books, music, artwork, prints, maps, diagrams, movies, photography, etc. are banned from duplicating outside the
limits of private home use and their related non-sale usage.
15
2
1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
39
212
Printing Using Basic Functions
A5 Document
A4 Printout
A4 Printout
A3 Document
<DP-24S>
B5 → B4 / A5 → A4 .. 141%
A4 → B4 / A5 → B5 .. 122%
B5 → A4 .................... 115%
<DP-24S>
A3 → B4 / A4→ B5 .....86%
B4 → A4 / B5 → A5 .... 81%
A3 → A4 / B4 → B5 .... 70%
STD STD
1:1
1
4
7
Enlargement and Reduction
Enlarging/Reducing from Standard-Size Document to Standard-Size Paper
You can enlarge or reduce a standard-size document onto standard-size printing paper.
The following zoom ratios are available when enlarging or reducing a standard-size document onto standard-size
printing paper.
■ Enlargements
You can enlarge a standard-size document onto standard-size paper using the following zoom ratios:
● European paper sizes
<DP-22S>
A5 → A4 .................... 141%
A5 → B5 .................... 122%
B5 → A4 .................... 115%
● U.S. paper sizes
<DP-22L>
141%
ST → LTR.................. 129%
121%
■ Reductions
You can reduce a standard-size document onto standard-size paper using the following zoom ratios:
● European paper sizes
<DP-22S>
A4 → B5 ...................... 86%
B4 → A4 / B5 → A5 .... 81%
A3 → A4 / B4 → B5 .... 70%
● U.S. paper sizes
<DP-22L>
LGL→ LTR.................. 77%
LDG→ LGL.................74%
LDG→ LTR ................. 64%
IMPORTANT
• Set the desired zoom ratio before starting the platemaking process.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Press
(ENLARGEMENT) key or
(RE-
DUCTION) key.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Notes on Safety (Please Read and Observe)
Conventions Used in This Manual
Each page of descriptions in this manual of how to operate the DP-22S/22L/24S is set up as follows.
■ Pictorial Symbols and Other Notations Used in This Manual
IMPORTANT : Introduces instructions for correct operation of the machine. If these instructions are ignored,
the machine may not be able to operate at optimum performance or may break down.
Tip : Introduces information that is useful for operation and maintenance of the machine, or
information about the machine’s performance, etc.
Continue Page
•••
: Indicates that the description of the operating sequence is continued on the next page.
(a P.00 “xxxx”) : Indicates the page number and item containing related information.
In the text of this manual, keys are indicated as follows:
: (PLATE MAKING) key
Title (Function)
Description of function and
example of printing
The illustration is designed to
indicate the result of using the
selected function.
Description of operational steps
Each step is described in detail.
Illustrations
The illustrations provide a visual
reference to which keys to operate
and other related conditions.
Before Using This Machine
1
Chapter 1
Before Using This Machine
This chapter contains essential information such as the names of the machine parts, the
names and functions of keys, etc., on the control panel, and the sizes of documents and
printing papers that you can use. Please be sure to read this chapter carefully before
attempting to use the printer.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
System Setup ..................................................................................................... 18
Part Names and Their Functions ...................................................................... 19
Printer Appearance...................................................................................... 19
Control Panel ............................................................................................... 22
LCD Panel.................................................................................................... 24
T urning Power ON/OFF...................................................................................... 25
Turning ON Printer Power............................................................................ 25
Turning OFF Printer Power .......................................................................... 26
Standard Mode ............................................................................................ 26
Key Card Counter [Available only with Key Card Counter installed] ............ 27
Document/Printing Paper Specification .......................................................... 28
Acceptable Documents................................................................................ 28
Acceptable Printing Paper ........................................................................... 28
How Platemaking and Printing is Performed .................................................. 29
Platemaking ................................................................................................. 29
Printing......................................................................................................... 29
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
18
System Setup
The machine and its optional equipment are set up as follows:
Personal computer
Key card counter
Duplo Direct Print System
Documents prepared on a
personal computer can be
printed on this machine.
PC interface kit is required
to connect this machine to
a personal computer.
ADF
Cabinet
Tape cluster
Drum unit
: Option
19
3
2
1
Before Using This Machine
1
Part Names and Their Functions
Printer Appearance
q
!1
w
e
r
t
y
u
i
!0
o
No. Name Function
q Document cover Keeps the document in contact with the document glass plate.
w Feed tray descend switch Press to lower the feed tray.
e Feed pressure adjuster lever Use to adjust the paper feed pressure.
r Side guides Slide to match the width of the paper.
t Feed tray Load paper in this tray.
y Support tray Pull out when using large paper sizes.
u Power switch Press to switch the power on and off.
i Cabinet (Option) Place the printer on this stand.
o Castor locks Lock the printer in position on the floor. Always lock the castor
locks when installing the printer.
!0 Front cover Open to replace ink pack and drum unit, etc.
!1 Control panel Displays operations and statuses, and sets functions.
Reference
page
32, 38,
103
35
34
34
34
25, 26
—
—
84, 92
22
20
Part Names and Their Functions
Front cover
Drum handle
Drum unit
Ink pack
Scanner unit
Lever
This lever releases the ink
pack holder.
Master set lever
When the master set lever is pushed,
the master is pulled in and set.
Lever
This lever is locks or
unlocks the drum.
Master roll
Master cover
Master cover
release lever
21
3
2
1
Before Using This Machine
1
Part Names and Their Functions
No. Name Function
!2
Plate ejection box release lever
Press to open the master ejection box.
!3 JOG switch Press and hold to rotate the drum for a set time. Use to remove
paper jams, etc..
!4 Print tray Holds the printed paper.
!5 Paper stopper Slide to match the size of printed paper.
!6 Paper stacker guides Slide to match the size of printed paper.
!7 Master ejection box Open to replace the master ejection core, etc..
!8
Plate ejection box lid release lever
Press to open the top of the master ejection core box. Use when
replacing the master ejection core, etc..
Reference
page
—
—
49
50
49
90
90
Master ejection
core
!2
!3
!4
!7
!5
!6
!8
22
Control Panel
Part Names and Their Functions
No. Name Function
q “OK” monitor Flashes to display the content of the trouble and lights to indicated
the part that caused the trouble in the machine.
w “ENLARGEMENT” key Press to set the enlargement ratio.
“100%” key Press to reset the ration to 100%.
“REDUCTION” key Press to set the reduction ratio.
100% lamp Lights when the 100% ratio is selected.
e “DOCUMENT MODE Press to switch between the text mode, text/photograph mode and
photograph mode. Each press of this key moves the position of the
lit lamp that indicates the selected document mode.
Document mode indicator lamps
The lamp of the selected mode lights.
r LCD panel Displays the number of printed paper.
Also displays an error message when an error occurs.
t
“FUNCTION SWITCH” key
Press to toggle between the normal mode and the function select
mode.
“SELECT” key Press to select a function.
y “TEST PRINT” key Press to print only one piece of paper for checking the print dark-
ness or printed position.
u “PLATEMAKING” key Press to start platemaking.
Reference
page
99
39
40
39
40
48
48
24, 99
54
54
33
SWITCH” key
STD STD
1:1
q w e
!4!5!7 !6
23
3
2
1
Before Using This Machine
1
Part Names and Their Functions
No. Name Function
i “STOP” key Press to stop printing on the way.
If this key is pressed while the machine is stopped,
the total number of prints and plates will be displayed
on the LCD panel.
o “PRINT” key Starts printing. This will not start platemaking.
Platemaking will start automatically after the end of
printing if there is a document on the ADF (Option).
!0 “ALL CLEAR” key Returns the control panel settings to the “Standard
Mode” settings. Press and hold for at least 0.5
seconds.
!1
X
=
key Press to enter the number of prints and number of sets
for sectional prints.
!2 Key pad Use to enter the number of prints.
!3 “CLEAR” key Press to reset the displayed number of prints to “0”.
Only the number of prints is cleared.
!4 Printing speed indicator lamp The lamp of the specified printing speed lights.
!5
“PRINTING SPEED ADJUSTMENT” keys
Press to adjust the printing speed.
!6
“PRINTING POSITION ADJUSTMENT” keys
Press to adjust the printing position.
!7 Printing position indicator lamp The lamp of the specified printing speed lights.
Reference
page
79
33
71
80
80
81
81
1
4
7
0
2
5
8
C
3
6
9
X
=
T
y ur t
i
o!0!1!2!3
24
No. Name Function
q Print count Displays the number of prints to be made.
w Sets Displays the number of sets to be printed.
Reference
page
33
69
0sht 1set
q w
LCD Panel
Part Names and Their Functions
25
3
2
1
Before Using This Machine
1
This section describes the operating sequence from turning ON the power switch until the printer is ready to make
prints, and how to turn OFF the printer power.
Turning ON Printer Power
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Connect the power cable to the printer and a
wall outlet.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Switch the power switch to the “
” position.
The power turns ON.
The message “SET PRINT PAPER” is displayed on the LCD
panel.
The printer functions are now set in “Standard Mode”
(a page 26).
When paper is loaded in the feed tray, the screen shown at
right is displayed.
When the screen shown at right is displayed, insert a key
card. (a See page 27, “Key Card Counter”.)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Turning Power ON/OFF
SET PRINT PAPER
0sht 1set
SET KEYCARD
26
Turning OFF Printer Power
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Switch the power switch to the “ ” position.
The power turns OFF and the display lamps on the control
panel turn OFF.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Standard Mode
When the printer power is first turned ON or (ALL CLEAR) key is pressed, the functions are reset to
standard mode. The standard mode settings are as follows:
• Print quantity : 0
• Print position : Standard lit
• Print speed : Standard lit
• Zoom : 100% lights
• Document mode : Standard lit
• 2 IN 1 : OFF
Turning Power ON/OFF
• PLATE SIZE : DP-22S/A4, DP-24S/B4
• PLA TE DARKNESS : NORMAL
• ✕94% : OFF
• 2 - up : OFF : ADF 2IN1
• SHADOW ERASER : OFF
• MANUAL ZOOM : OFF
27
3
2
1
Before Using This Machine
1
Key Card Counter
Available only with Key Card Counter installed
With the key card counter installed, you can control the platemaking and print quantities per person or per
department, etc. See the Instruction Manual for the Key Card Counter for details.
■ Inserting a key card
When you turn on the power, the icon shown at right is
displayed if no key card has been inserted in the key card
counter.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Insert a key card in the key card counter.
The printer can now be operated as normal.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
■ Handling key cards
Turning Power ON/OFF
Do not bend or soil a key card. Do not insert any objects other than
key cards into the key card slot.
Keep your key card well away from
magnetic fields.
SET KEYCARD
28
Document/Printing Paper Specification
Acceptable Documents
■ Document glass plate
• Weight : Sheet documents, books, etc, not exceeding 10kg.
• Size : 297mm X 432mm
■ ADF
• Document thickness : 64g/m2 to 128g/m
2
• Document size : A3 to A5 size
ST to 11x17-in. (ST size in landscape mode: STR cannot be used.)
• Stacking capacity in document tray : 100 sheets (64g/m2)
IMPORT ANT
The following types of document cannot be used:
• Documents with large file-binding holes, tears, or missing parts
• Documents with staples or paper clips attached
• Documents with markedly curling ends/sides, or marked folds
• Carbon-backed documents
• Sticky documents
• Highly transparent documents such as OHP film
When ADF is installed:
• To make a new plate from a document from which a plate has already been made, remove
and then reload the document.
• Always use documents of the same size.
• If you load documents of different lengths, the printer may not operate correctly.
Acceptable Printing Paper
DP-22S DP-22L DP-24S
Paper thickness
Paper stacking capacity
Paper size
* With paper larger than 297 x 432 → 60sheets/min. DP-24S-standard, DP-22S/L-optional.
DP-22S DP-22L DP-24S
Printing area 204mm X 288mm 210mm X 355mm 250mm X 355mm
IMPORTANT
The following types of paper cannot be used.
• Paper with large file-binding holes
• Paper with staples or paper clips attached
• Paper with markedly curling ends/sides, or marked folds
• Carbon-backed paper
• Paper with smaller pieces of glued paper
45g/m2 to 210g/m2 (40kg ~ 180kg)
Feed tray : 1300 sheets (64g/m2 top-grade paper)
Print tray : When a cabinet is used:1300 sheets (64g/m2 top-grade paper)
When the printer is used on a table: 900 sheets (64g/m2 top-grade paper)
Max. 271mm X 382mm Max. 271mm X 382mm Max. 271mm X 382mm
(297mm X 432mm)* (297mm X 432mm)* (297mm X 432mm)*
Min. 100mm X 150 mm Min. 100mm X 150 mm Min. 100mm X 150 mm
29
3
2
1
Before Using This Machine
1
How Platemaking and Printing is Performed
The machine performs two processes: platemaking and printing.
Platemaking
In the “platemaking” process, the old master on the drum is removed while the thermal head creates the
scanned image on the new master and transfers it onto the drum.
Printing
In the “printing” process, paper separated from the stack by the feeder roller and paper separator unit is
pressed against the drum unit by the press roller. There are small holes over only the image area of the master
that is attached to the drum, and ink that seeps from these holes is transferred to the paper. The paper is then
peeled from the master by the paper stripper finger. The paper is directed onto the paper ejection belt by a fan
unit and discharged from the machine.
Master roll
Thermal head
Drum
unit
Master ejection box
Drum unit
Paper stripper finger
Press roller
Paper separator unit
Fan unit
Paper ejection belt
Feeder roller
Paper
Ink
Loading...