Duo-Fast HT550, HT755 Operation Manual
Cleaning and
Clearing A Jam
For efficient use, this tool
should be cleaned
periodically. The Front Jaw
can be removed to give
access to the staple
Magazine for cleaning and
jam clearing. Damage to
parts and/or excessive
accumulation of dirt are the
principal causes of jams. If a
jam should occur, or if
cleaning is required,
disengage staple feeder
spring and remove all
staples. Unhook the Jaw and
release as shown (1). Swing
Trip Lever out of position by
lifting round head pin from
notch on top of Trip Lever
(2). Slip off Front Jaw by
pivoting it down and off from
back end (3). Then remove
any jammed staples and
carefully clean the tool.
Hammer Stapler
Operation and
Maintenance Manual
HT-550 (use only 5000 staples)
HT-755 (use only 7500 staples)
Limited Warranty
WHAT IS COVERED: This warranty covers any defects in material or
workmanship. HOW LONG: This warranty lasts one year from the date of
original purchase. WHAT DUO-FAST WILL DO: Duo-Fast will within one
year from date of original purchase replace or repair the tool without any
cost for parts or labor.
WHAT IS NOT COVERED: This warranty does not cover damage by
accident, misuse, unauthorized repair or modification. Also consequential
and incidental damages (including but not limited to lost profits, lost sales
and injury to property) are not recoverable under this warranty. Some
states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This
warranty is the exclusive express warranty and any representations or
promises inconsistent with or in addition to this warranty are unauthorized
and shall not be binding on Duo- Fast. Finally, the IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE LIMITED IN DURATION TO A PERIOD
OF ONE YEAR FROM THE DATE OF PURCHASE BY THE ORIGINAL
CONSUMER. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
HOW TO GET SERVICE: To obtain repair or replacement under this
warranty, the tool must be returned to the nearest authorized Duo-Fast
service center, postage prepaid together with proof of original purchase
date (sales receipt or other). Consult your white pages for the authorized
Duo-Fast service center in your area or call, toll-free, 1-800-752-5207.
HOW STATE LAW APPLIES: This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
To replace Front Jaw
- reverse the above procedure, making sure the
driver blade is fitted correctly in the slot provided in the front jaw.
Then pivot the jaw back end up and into place. If the tool continues to
jam, have it serviced by qualified service personnel or contact your
Duo-Fast Distributor for additional help.
HAMMER STAPLER TIPS
• The staple Feeder Bar should slide freely on the Channel.
• The staple Feeder Spring must have sufficient tension to feed the staples
properly.
• In addition to occasional cleaning, apply a light film of grease to the
driver plunger.
Parts—Parts listed below may be ordered from your nearest
authorized Duo-Fast Service Center. When ordering parts,
always give the following information: (1) part number; (2) part
description; (3) model number; (4) name of item—Hammer
Stapler.
Repair parts:
Part No. Description Model No.
766 Jaw Release Spring HT-755
7066 Jaw Release Spring HT-550
5556A Front Jaw HT-550
756A Front Jaw HT-755
5513 Feeder Bar HT-550
713 Feeder Bar HT-755
743 Plastic Handle HT-755
7043 Plastic Handle HT-550
744-A Handle Mount Screws All Models
Form HT-185 4/97
Duo-Fast Corporation
USA 1-888-DUO-FAST
Duo-Fast Corporation is the leading manufacturer of automatic
industrial stapling and nailing equipment. Consult White Pages
for the authorized Duo-Fast Distributor in your area.
READ BEFORE USING TOOL. IF WARRANTY TERMS ARE NOT
ACCEPTABLE, RETURN AT ONCE UNUSED FOR REFUND.
EMPLOYER’S RESPONSIBILITIES
Employer must provide the recommended safety eye protection
equipment, as required in the first paragraph of the SAFETY
INSTRUCTIONS, for use by the tool operator and everyone in
the vicinity of the tool. Employer must enforce compliance with
the SAFETY INSTRUCTIONS and all applicable OSHA
regulations. Employer must provide complete training in safe
tool operation for all tool operators as well as provide an
instruction manual for use by all tool operators.
1.
2.
3.
Always Wear
Safety Glasses
When Using
Power Tools
XA-1011 CLEAR
XA-1022 TINTED
Cleaning and
Clearing A Jam
For efficient use, this tool
should be cleaned
periodically. The Front Jaw
can be removed to give
access to the staple
Magazine for cleaning and
jam clearing. Damage to
parts and/or excessive
accumulation of dirt are the
principal causes of jams. If a
jam should occur, or if
cleaning is required,
disengage staple feeder
spring and remove all
staples. Unhook the Jaw and
release as shown (1). Swing
Trip Lever out of position by
lifting round head pin from
notch on top of Trip Lever
(2). Slip off Front Jaw by
pivoting it down and off from
back end (3). Then remove
any jammed staples and
carefully clean the tool.
Hammer Stapler
Operation and
Maintenance Manual
HT-550 (use only 5000 staples)
HT-755 (use only 7500 staples)
Limited Warranty
WHAT IS COVERED: This warranty covers any defects in material or
workmanship. HOW LONG: This warranty lasts one year from the date of
original purchase. WHAT DUO-FAST WILL DO: Duo-Fast will within one
year from date of original purchase replace or repair the tool without any
cost for parts or labor.
WHAT IS NOT COVERED: This warranty does not cover damage by
accident, misuse, unauthorized repair or modification. Also consequential
and incidental damages (including but not limited to lost profits, lost sales
and injury to property) are not recoverable under this warranty. Some
states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This
warranty is the exclusive express warranty and any representations or
promises inconsistent with or in addition to this warranty are unauthorized
and shall not be binding on Duo- Fast. Finally, the IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE LIMITED IN DURATION TO A PERIOD
OF ONE YEAR FROM THE DATE OF PURCHASE BY THE ORIGINAL
CONSUMER. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
HOW TO GET SERVICE: To obtain repair or replacement under this
warranty, the tool must be returned to the nearest authorized Duo-Fast
service center, postage prepaid together with proof of original purchase
date (sales receipt or other). Consult your white pages for the authorized
Duo-Fast service center in your area or call, toll-free, 1-800-752-5207.
HOW STATE LAW APPLIES: This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
To replace Front Jaw
- reverse the above procedure, making sure the
driver blade is fitted correctly in the slot provided in the front jaw.
Then pivot the jaw back end up and into place. If the tool continues to
jam, have it serviced by qualified service personnel or contact your
Duo-Fast Distributor for additional help.
HAMMER STAPLER TIPS
• The staple Feeder Bar should slide freely on the Channel.
• The staple Feeder Spring must have sufficient tension to feed the staples
properly.
• In addition to occasional cleaning, apply a light film of grease to the
driver plunger.
Parts—Parts listed below may be ordered from your nearest
authorized Duo-Fast Service Center. When ordering parts,
always give the following information: (1) part number; (2) part
description; (3) model number; (4) name of item—Hammer
Stapler.
Repair parts:
Part No. Description Model No.
766 Jaw Release Spring HT-755
7066 Jaw Release Spring HT-550
5556A Front Jaw HT-550
756A Front Jaw HT-755
5513 Feeder Bar HT-550
713 Feeder Bar HT-755
743 Plastic Handle HT-755
7043 Plastic Handle HT-550
744-A Handle Mount Screws All Models
Form HT-185 4/97
Duo-Fast Corporation
USA 1-888-DUO-FAST
Duo-Fast Corporation is the leading manufacturer of automatic
industrial stapling and nailing equipment. Consult White Pages
for the authorized Duo-Fast Distributor in your area.
READ BEFORE USING TOOL. IF WARRANTY TERMS ARE NOT
ACCEPTABLE, RETURN AT ONCE UNUSED FOR REFUND.
EMPLOYER’S RESPONSIBILITIES
Employer must provide the recommended safety eye protection
equipment, as required in the first paragraph of the SAFETY
INSTRUCTIONS, for use by the tool operator and everyone in
the vicinity of the tool. Employer must enforce compliance with
the SAFETY INSTRUCTIONS and all applicable OSHA
regulations. Employer must provide complete training in safe
tool operation for all tool operators as well as provide an
instruction manual for use by all tool operators.
1.
2.
3.
Always Wear
Safety Glasses
When Using
Power Tools
XA-1011 CLEAR
XA-1022 TINTED
IMPORTANT SAFETY INSTRUCTIONS
For personal safety and proper operation of this tool read
all of these instructions carefully.
To avoid serious eye injury from fasteners, approved eye
protection must be worn by the tool operator and everyone in the vicinity of the tool. Use safety glasses with
side shields, goggles, or a wide-vision safety mask over
prescription glasses. Eye protection equipment must
conform to the requirements of the latest revision of the
American National Standards Institute (ANSI) Standard
Z87.1, Practice for Occupational and Educational Eye
and Face Protection. Eye protection which meets these
requirements also conforms to OSHA regulations.
Duo-Fast Staples are manufactured to very exact and
critical specifications for safe and proper tool operation.
Do not use fasteners other than the type and lengths
specified for this tool. Using improper fasteners can
cause jamming, damage to the tool and serious injury to
yourself or others in the work area from fastener
fragments, a ricocheting fastener or flying debris from an
improperly driven fastener.
Do not use a tool that is not working properly. Have it
repaired by qualified service personnel.
Always assume that the tool contains fasteners.
Never point the tool toward yourself or anyone else,
whether it contains fasteners or not.
To avoid serious personal injury from discharged
fasteners, never operate/activate the Trip Lever with your
fingers, thumbs or palm of your hand.
Respect the tool. It is powerful and can be dangerous if
not handled properly. Do not engage in horseplay.
Do not modify a tool in any way unless the modification
is approved by Duo-Fast Corp.
To avoid personal injury to yourself and others, obtain
complete training in safe tool operation and read all of
this instruction manual before using the tool.
Refer to this instruction manual for detailed information
on the proper use and maintenance of the tool.
Repairs to a tool must be performed by qualified service
personnel only. Use only Duo-Fast authorized parts for
repair or replacement. Never remove the front jaw
without first disengaging the pusher assembly and
removing all staples from the tool.
If you have any questions about safe tool operation,
contact your local Duo-Fast office or Sales/Service
representative for help. If no one is immediately
available, or cannot answer your questions, please call
Duo-Fast at 1-888-DUO-FAST for assistance.
Loading Staples
Be sure you only use Duo-Fast Staples of the correct type
and size, as marked on the side of the tool. Using improper
staples can cause jamming, damage to the tool and
serious injury to yourself or others in the work area from
staple fragments, a ricocheting staple or flying debris
from an improperly driven staple.
1.) Lift Handle lid “A” up.
2.) Pull Feed Spring “B” to the back of the tool and
disengage it from the Feeder Bar “C”
3.) Slide 2 strips of the correct type and size Duo-Fast
Staples into the Magazine through the back end.
4.) Slide the Feeder Bar “C” behind the staples.
5.) Hook the Feeder Spring “B” onto the Feeder Bar and
allow it to move forward.
Driving Staples
Swing the tool like a hammer. The Trip Lever will drive a
staple as it contacts the surface you are hitting. Do not
hit the material being stapled any harder than necessary
to drive the staple. You will get a feeling for the amount of
force to use after a few trials.
CAUTION—Do not use the top surface of the tool to tap
down improperly driven staples. This could eject a staple
from the tool and cause injury to yourself or other
persons in the work area.
IMPORTANT SAFETY INSTRUCTIONS
For personal safety and proper operation of this tool read
all of these instructions carefully.
To avoid serious eye injury from fasteners, approved eye
protection must be worn by the tool operator and everyone in the vicinity of the tool. Use safety glasses with
side shields, goggles, or a wide-vision safety mask over
prescription glasses. Eye protection equipment must
conform to the requirements of the latest revision of the
American National Standards Institute (ANSI) Standard
Z87.1, Practice for Occupational and Educational Eye
and Face Protection. Eye protection which meets these
requirements also conforms to OSHA regulations.
Duo-Fast Staples are manufactured to very exact and
critical specifications for safe and proper tool operation.
Do not use fasteners other than the type and lengths
specified for this tool. Using improper fasteners can
cause jamming, damage to the tool and serious injury to
yourself or others in the work area from fastener
fragments, a ricocheting fastener or flying debris from an
improperly driven fastener.
Do not use a tool that is not working properly. Have it
repaired by qualified service personnel.
Always assume that the tool contains fasteners.
Never point the tool toward yourself or anyone else,
whether it contains fasteners or not.
To avoid serious personal injury from discharged
fasteners, never operate/activate the Trip Lever with your
fingers, thumbs or palm of your hand.
Respect the tool. It is powerful and can be dangerous if
not handled properly. Do not engage in horseplay.
Do not modify a tool in any way unless the modification
is approved by Duo-Fast Corp.
To avoid personal injury to yourself and others, obtain
complete training in safe tool operation and read all of
this instruction manual before using the tool.
Refer to this instruction manual for detailed information
on the proper use and maintenance of the tool.
Repairs to a tool must be performed by qualified service
personnel only. Use only Duo-Fast authorized parts for
repair or replacement. Never remove the front jaw
without first disengaging the pusher assembly and
removing all staples from the tool.
If you have any questions about safe tool operation,
contact your local Duo-Fast office or Sales/Service
representative for help. If no one is immediately
available, or cannot answer your questions, please call
Duo-Fast at 1-888-DUO-FAST for assistance.
Loading Staples
Be sure you only use Duo-Fast Staples of the correct type
and size, as marked on the side of the tool. Using improper
staples can cause jamming, damage to the tool and
serious injury to yourself or others in the work area from
staple fragments, a ricocheting staple or flying debris
from an improperly driven staple.
1.) Lift Handle lid “A” up.
2.) Pull Feed Spring “B” to the back of the tool and
disengage it from the Feeder Bar “C”
3.) Slide 2 strips of the correct type and size Duo-Fast
Staples into the Magazine through the back end.
4.) Slide the Feeder Bar “C” behind the staples.
5.) Hook the Feeder Spring “B” onto the Feeder Bar and
allow it to move forward.
Driving Staples
Swing the tool like a hammer. The Trip Lever will drive a
staple as it contacts the surface you are hitting. Do not
hit the material being stapled any harder than necessary
to drive the staple. You will get a feeling for the amount of
force to use after a few trials.
CAUTION—Do not use the top surface of the tool to tap
down improperly driven staples. This could eject a staple
from the tool and cause injury to yourself or other
persons in the work area.
Loading...