Dunelm Soho Series Assembly Manual
DEAR CUSTOMER
Thank you for purchasing your new piece of furniture from Dunelm.
We put a lot of effort in the design and construction of our products to ensure they set
the standard for quality, durability and ease of assembly.
If for any reason you feel we haven’t lived up to the high standards we set ourselves,
please don’t hesitate in contacting us on 08451 656565 where our team will be very
keen to understand what has gone wrong and, more importantly, put it right.
DEAR CUSTOMER
The next step…
There is no need to feel daunted by the number of parts and ttings in front of you, we have
compiled this straight forward, step-by-step guide to make sure that assembling your furniture
is as easy as 1, 2, 3.
Before you begin, we advise that you check that you have everything you need to get started.
TOP TIP
Find a space to spread these out across the oor before you begin
assembling them. Lay each panel down in position, ready to build.
It is recommended that two people assemble this product together.
The full list of furniture parts, xtures and ttings, as well as the tools you will need for assembly,
can be found on pages 2, 3 and 4 of this manual.
TOP TIP
Identify all of the ttings, make sure that you have them all prepared
and familiarise yourself with each component, to make things easier
when you are putting it all together.
Safety and Care Advice
IMPORTANT - The rst step you need to take is to ensure your safety!
Please take the time to read and understand these instructions before assembling your
furniture.
Keep children and animals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrapping materials away from children to avoid danger of suffocation.
Ensure that all packaging is disposed of carefully and responsibly.
Make sure that you allow enough space to move around when assembling your furniture.
Parts & Fittings for Soho Small Sideboard (30149782 / 30149737)
Panel exploded view
1
4
13
Panels - plan view
14
13
6
3
7
5
2
11
11
11
9
9
9
10
12
8
12
8
12
8
1
Top Panel (90x40cm)
2
Bottom Panel (90x40cm)
3
Left Side Panel
(59x39.9cm)
4
Right Side Panel
(59x39.9cm)
2
5
Divider Panel
(59x37.6cm)
7
Left door
(42x58.5cm)
6
Shelf (41.5x35.6cm)
8
Drawer front x3
(42x19.3cm)
Drawer left side panel x3
9
(35x14cm)
Drawer right side panel x3
10
(35x14cm)
Drawer back panel x3
11
(36.5x14cm)
Drawer bottom panel x3
12
(37.5x34.8cm)
Front rail
14
(41.6x7.6cm)
Back Panel x2
13
(60x42.6cm)
Fittings
A B C
36mm Connecting bolt x12 15mm Locking cam x12 Cap x12
D E F
8mm Wooden dowel x14 6mm Wooden dowel x6 Door hinge x2
G H I
15mm Screw x48 50mm Screw x2 Allen key x1
J K L
Shelf pin x4 Rear panel connector x8 18mm Screw x8
M N O
28mm Connecting bolt x12 13mm Locking cam x12 30mm Screw x12
P Q R
12mm Screw x21 Magnetic Push Catch x1 Washer x1
3
S
Wall strap x2
T
13mm Washer x2
U
350mm Runner x6
V
Leg x4
W
12mm Screw x1
Tools required
Cross slot screwdiver Hammer Tape measure
The use of power tools to assemble the product is not recommended due to the risk of
Before you start
Check the pack and make sure you have all the parts listed above. If not, contact the
helpline on 08451 656565 who will be able to help you.
When you are ready and sure that you have the right tools to hand, you will need plenty
of space and a clean dry area for assembly.
Ready?
Follow this step-by-step guide
1
2
G
V1
V
G
V1
2
V1
V2
G
x 4
G
V1
V1
4
3
4
V2
V1
V2
V1
V2
2
V2
V1
V1
5
D
U
x 6
U
U1
U2
Divider Panel
G
D
B
G
G
B
A
G
U
G
U1
G
U1
D
5
D
Fully insert locking
cams on the boards,
the slot always points
to the outlet of holes.
Slot
Outlet
Screw connecting
bolts as far as shown
Do not over tighten.
5
Loading...