DEAR CUSTOMER
Thank you for purchasing your new piece of furniture from Dunelm.
We put a lot of effort in the design and construction of our products to ensure they set
the standard for quality, durability and ease of assembly.
If for any reason you feel we haven’t lived up to the high standards we set ourselves,
please don’t hesitate in contacting us on 08451 656565 where our team will be very
keen to understand what has gone wrong and, more importantly, put it right.
DEAR CUSTOMER
The next step…
There is no need to feel daunted by the number of parts and fittings in front of you, we have
compiled this straight forward, step-by-step guide to make sure that assembling your furniture
is as easy as 1, 2, 3.
Before you begin, we advise that you check that you have everything you need to get started.
TOP TIP
Find a space to spread these out across the floor before you begin
assembling them. Lay each panel down in position, ready to build.
It is recommended that two people assemble this product together.
The full list of furniture parts, fixtures and fittings, as well as the tools you will need for assembly,
can be found on page 2 and 3 of this manual.
TOP TIP
Identify all of the fittings, make sure that you have them all prepared
and familiarise yourself with each component, to make things easier
when you are putting it all together.
Safety and Care Advice
IMPORTANT - The first step you need to take is to ensure your safety!
Please take the time to read and understand these instructions before assembling your
furniture.
Keep children and animals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrapping materials way from children to avoid danger of suffocation.
Ensure that all packaging is disposed of carefully and responsibly.
Make sure that you allow enough space to move around when assembling your furniture.
Parts & Fittings for the Perth 2 Drawer Bedside Unit (30151824)
Panels - plan view
Left side
390x 393mm
Right side
390x 393mm
Top 425 x 395mm
L/H top drawer side
350 x 135mm X 2
R/H top drawer side
350 x 135mm X 2
Drawer back
348.5 x 133mm X 2
Drawer base
352 x 347mm X 2
Drawer front
375 x 192mm X 2
Back
408 x 399mm
Base
421 x 395mm
Panel exploded
view
Foot X 4
1 2
3 4
5 6 7 8
9
10
1
3
4
5
6
7
8
9
2
10
5
6
7
8
9
N
N
N
N
N
2
Cross slot screwdriver Hammer Tape measure
Tools required
The use of power tools to assemble the product is not recommended due to the risk of
over tightening fixings
Ready?
Follow this step-by-step guide
Ensure the cam is pressed fully into the
hole and arrow pointing towards the top edge
10 mm
Front edge
Before you start
Check the pack and make sure you have all the parts listed above. If not, contact the
helpline on 08451 656565 who will be able to help you.
When you are ready and sure that you have the right tools to hand, you will need plenty
of space and a clean dry area for assembly.
Fittings
Euro screw
s x 8
Soft close runner x 2 pair
40mm Screw x 4
Handle x 2
3
1
A
C
A
C
C
A
1
1
15mm
Metal cam x 4
A
Cam pin x 8
B
30mm
Wooden dowel x 8
C
Panel pins x 12
H
F
Handle screw x 4
L
K
12mm
Metal cam x 4
D
Drawer peg x 8
G
E
M
Drawer wedge x 4
I
50mm Screw x 4
J
C
C
Ensure the cam is pressed fully into the
hole and arrow pointing towards the top edge
10 mm
Front edge
Front edge
4
2
C
A
3
2
2
1
F
M
F
M
1
M
M
1
M
A
C
A
C
C
C
Rear edge
Note: Insert metal
dowels as far as shown.
Front edge
Rear edge
B
B
B
B
B
3
5
4
5
6
M
2
F
M
F
M
2
M
M
2
4
J
J
J
N
N
N
N
J
Cam lock in closed
position
Cam lock in open
position
Front edge
Front edge
Two people required
to turn unit over
Front edge
Front edge
Front edge
Front edge
A
A
A
A
3
1
A
3
1
6
7
8
9
Cam lock in closed
position
Cam lock in open
position
A
A
2
A
A
3
1
2
3
1
E
E
E
E
4
Back of unit
Two people required
to stand unit upright
Ensure the cam is pressed fully
into the hole and arrow pointing
towards the short edges
Front edge
3
1
A to B = C to D
10
2
H
10
H
10
7
10
11
12
D
5
D
3
H
H
6
D
4
10
2
4
H
X 2 X 2
Note: Insert metal
dowels as far as shown.
5
6
7
G
G
8
13
14
5
6
7
8
G
X 2
X 2
15
B
9
B
B
X 2
Cam lock in open
position
Cam lock in closed
position
9
5
6
8
9
X 2
I
I
16
7
5
7
8
9
L
L
K
X 2
6
17
18
D
D
5
6
D
D
D D
5
6
7
8
9
8
8
9
9
X 2
19
10
5
FIRST
X 2
1
7
6
M
M
2
7
1
2
LEFT AND RIGHT DRAWER RUNNERS
REPEAT PROCEDURE
FOR THE SECOND
DRAWER
UNDERNEATH
DRAWER
6
5
M
1
2
Drop drawers onto the runners and position the pegs into the holes at the back
(FIG A) and on the underside of the drawer sides (FIG B).
FIG. B
FIG. A
M
M
2
1
9
6
2
SECOND
1
7
5
M
3
X 2
Nearly there!
9
2
1
7
5
M
3
6
11
FIRST SECOND
TO RELEASE DRAWER
5
6
M
2
1
8
X 2
TO SECURE DRAWER
5
6
2
1
8
X 2
M
UNDERNEATH
DRAWER
Lift green clip up and push towards
the runner (arrowed below), this
secures the drawer onto the drawer
runner and prevents the drawer from
popping out.
UNDERNEATH
DRAWER
20
21
L
TO ADJUST
DRAWER HEIGHT
2
1
8
X 2
UNDERNEATH
DRAWER
5
6
To adjust drawer height turn the
green wheel clockwise or anticlockwise.
To remove the drawer pull out the
green tab and clip back.
Repeat the process for the other
drawer runner then lift the drawer
from runners.
M
Finally, we hope you enjoy your furniture for
many years to come and thanks again
for your purchase.
dunelm.com
Care and maintenance
Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
From time to time check that there are no loose screws on this unit.
This product should not be discarded with household waste. Take to your local authority waste
disposal centre.
Loading...