Dunavox DAU-52.146W, DAU-52.146B, DAB-48.125B, DAU-52.146SS, DAU-32.83W Instruction Manual

WINE CABINET INSTRUCTION MANUAL

DAU-32.78DB, DSS

DAU-46.146D B, DSS, DW

DAB-42.117DB, DSS

2018.V.8.

Model:

One section model:

DAB-48.125B, SS DAU-52.146B, SS, W

DAU-32.83B, SS, W

Two section model:

Three section model: DX-89.246TB, TSS

Please read this manual carefully before installing and starting up, and
store it in a safe place. If you pass on the product to another person
hand over this instruction manual along with it.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic

precautions should always be followed to
reduce the risk of fir e, electric shock, and
injury to persons, including the following:

FOR YOUR SAFETY

Read all instructions carefully, even if you are

quite familiar with the appliance.

• The appliance is intended to be used for the
storage of wine. Use this appliance only as
described in this manual. Other uses not
recommended may cause fire, electric shock or
personal injury.

• This appliance can be used by children aged of 8
years and a bove and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if the y have been
given supervision or instruction concerning use
of the appliance in a safe way an d understand the
hazards invol ved. Children shall not play with the
appliance.

Cleaning and user maintenance shall not be
made by children without supervision.

• Electrical devices are not toys. Always keep
the device out of the reach of children. Keep the
mains cord out of the reach of children. Do not let
the mains cord hang over the edge of the ta ble or
worktop on which the appliance stands.

• To protect against the risk of electric shock, DO
NOT IMMERSE the unit, cord, or plug in water or
spray any other liquid.

• Unplug the appliance from the plug socket when
not in use, when mo ving from one location to
another and before cleaning.

• To disconnect the appliance, grip the plug and
pull it from the wall outlet. Never pull by the cord.

• WARNING: Please keep the appliance away
from substance, which can cause ignition. Do not
operate the appliance in the presence of
explosive and/or fl ammable fumes.

• Do not place the appliance or any of its part near
an open flame, cooking or other heating
appliance.

• Do not operate t he appliance with a dam aged
cord or plug, if the product malfunctions, or if it is
dropped or damaged in an y manner. If the supply
cord is damaged, it must be replaced by the
manufacturer, or an authorized service centre or
similarly qualifi ed persons in order to avoid a
hazard.

• The use of attachm ents not recommended by the
manufacturer m ay be hazardous.

• Place the unit on a dry level surface.

• Do not operate i f the housing is rem oved or
damaged.

• A loose fit between the AC outlet (receptacle) and
plug may cause o verheating and a distortion of
the plug. Contact a qualified electri cian to replace
loose or worn outlet.

• Locate the unit away from direct sunlight and
sources of heat (stove, heater, radiator, etc.).

• WARNING: This appliance is CFC- and HFCfree
and contains sm all quantities of Isobutane
(R600a) which is environmentally friendl y, but
flammable. It do es not damage the ozone layer,
nor does it increase the green house effect. Care
must be taken during transportation and setting
up of the appliance that no parts of the cooling
system are damaged. Leaking coolant can ignite
and may damage the e yes.
In the event of any damage:

- Avoid open flam es and anything w hich
createsa spark,

- Disconnect from the mains,

- Air the room in which the appliance is
locatedfor se veral minutes and

- Contact the Service Department for advice.

• The more coolant there is in an appliance, the
larger the room it should be installed in. In the
event of a leakage, if the appliance is in a small
room, there is the danger of combustible gases
building up. For every 8 g of coolant at least 1
cubic meter of room space is required. The
amount of coolant in the appli ance is stated on
the data plate inside the appliance. It is
hazardous for anyone other than an Authorised
Service Person to carry out servicing or repairs
to this appliance. In Queensland of Australia the
authorized person must hold a Gas Work
Authorisation for hydrocarbon refrigerants,
before carrying out servicing or repairs which
involve the removal of covers.

• WARNING: Keep ventilation openings, in the
appliance enclosure or in the built-in structure,
clear of obstruction. No liability will be accepted
for any damage incurred owing to misuse of the
appliance or as a result of repairs carried out by
unqualified personnel. In this case neither the
guarantee nor any other liability claims will apply.

• WARNING: Do not use mechanical devices or
other means to accelerate the defrosting
process, other than those recommended by the
manufacturer.

• WARNING: Do not damage the refrigerant
circuit. Never use an appliance with a damaged
circuit.

• WARNING: Do not use any electrical appliance
inside the wine storage com partment of the
appliance, unless they are of the type
recommended by the manufacturer.

• WARNING: To avoid a hazard du e to instability
of the appliance, it must be fixed in accordance
with the instructions.

• CAUTION: Please keep the products away from
the fire or similar glowing substance before you
dispose the refrigerator.

• Do not store explosive substances such as
aerosol cans with a flammable propellant in this
appliance.

• This appliance is intended to be used in
household and sim ilar applications such as

- staff kitchen areas in shops, offices and other
working environments;

- farm houses and by clients in hotels, motels
and other residential type environments; - bed
and breakfast type environments; - catering
and similar non-retail applications.

• Do not attempt to repair or replace any part of
your appliance unless it is specifically
recommended in this manual. All other servicing
should be referred to a qualified technician.

• Replace all panels after service before operating.

• Use two or more people to move and install the
appliance. Failure to do so can result in back or
other injury.

• Never clean appliance parts with flammable
fluids. These fumes can create a fire hazard or
explosion. And do not store or use gasoline or
other flammable vapors and liquids in the vicinity
of this or any other appliance. The fumes can
create a fire hazard or explosion.

• Do not connect or disconnect the electric plug
when your hands are wet.

• It is recom mended that a separate c ircuit, serving
only your appliance be provided. Use receptacles
that cannot be t urned off by a swi tch or pull chain.

• If you have a lockable appliance, do n ot keep the
key near the appliance or within reach of children.

SAVE THESE INSTRUCTIONS

If you are experiencing problems, check the
Troubleshooting Guide at the bac k of this manual. It
lists causes of minor operating problems that you can
correct by yourself.

DISPOSAL

Dispose of your appliance packaging properly.
Ensure that any plastic wrappings, bags etc. are
disposed of safel y and kept out of the reach of babies
and young children. Danger of suffocation!

Refrigeration equipment must be properly disposed of
in a professional and appropriate way, in accordance
with the current local regulations and laws which
protect the environment. This applies to your old
appliance and to your new unit once it has reached
the end of its service life.

WARNING: Please ensure that old, worn appliances
are rendered unusable before disposal by removing
the doors, remo ving the plug, cutting the network
cable, and remo ving or destroying any snap
fastenings or bolts. You wil l thus prevent children from
locking themselves in the appliance during play (risk
of suffocation) or endangering their lives in any other
way. DO NOT dispose of the a ppliance i n landfill as
the insulation (Cyclopentane) and refrigerant gas
(R600a) contained in these appliances are
flammable.

Disposal i nstructions:

• The appliance must not be disposed of in the
dustbin or with normal household rubbish.

• The coolant circuit, particularly the heat
exchanger at the back/bottom of the unit, must not
be damaged.

• The symbol on th e product or its packagi ng
indicates that this product is not to be handled as
normal household waste but is to be taken to a
recycling collection point for electrical and
electronic goods. By correctly disposing of this
product you are contributing to the protection of
the environment and to the health of your fellow
human beings. Improper disposal endangers
health and the en vironment. Further information
about the recycling of the product may be
obtained from your town hall, refuse collecti on
department or the store where you purchased the
product.

PRODUCT FEATURES

WARNING: To reduce the risk of fir e,
electric shock or personal injury, unplug
or disconnect the appliance from the
power supply before servicing.

• Built-in or Free-standing installation with single,
dual or three temperature zone, depending on
your model.

• Continuousl y variable electronic tem perature
control with digital display and touchpad input . 

Temperature can be set from 5° to 18°C or 22°C
(40° to 64°F or 72°F) for either compartment and
can be displayed in either Fahrenheit or Celsius.

• Can be set to the long time storage maturing
temperature or a specific serving temperature for
red/white/sparkling wines.

• Cooling and He ating (for particular items only) to
maintain the perfect storaging and/or service
condition.

• Dynamic compressor type cooling to e nsure
interior air circulation with even distribution of
temperature and humidity.

• Soft LED Interior Light with ON/OFF switch –
Function mode and Sh owcase mode.

• Open-door and malfunction warning system (for
particular items only)

• Sabbath mode will allow the lights to remain off
during certain religious observances (for
particular models only).

• Temperature memory function - If power is
interrupted (power surge, breaker switch, etc.)
and then powered up again, th e unit will operate
with the last temperature set-point. for particular
models only)

• Automatic defrosting with defrost
water evaporation.

• Reversible tempered doubl e/triple pane glass
door protects your wine from UV light and creates
an attracti ve display with few condensation and
low noise.

• Black coated matte steel outer frame and black
plastic interior liner offer lifetime performance and
stability. The black liner prevents excessive light
from damaging the maturity process.

• Full glass or seamless stainless steel-framed
glass door with stainless steel handle.

• Beech shel ves allow for maximum convenience
and flexibility to accommodate various size
bottles (except DX-7.20 models).

• Security lock system with keys (for particular
items only).

• Passive humidity control s ystem (Humidity Box).

• Active charcoal air filter (for particular items only).

NOTE: Features and specifications are subject to
change without notice.

INSTALL ATION

BEFORE US ING YOUR APPLI ANCE

• Remove all exterior and interior packing. Clean
the interior surface with lukewarm water using a
soft cloth. T he unit may have residual odors at
first, they will disappear as the unit cools.

• Before connecting the appliance to the power
source, let it stand upright for at least 24 hours.
This will reduce the possibility of a malfunction in
the cooling system caused by handling during
transportation. During this time we recommend
that you leave the door open to clear any residual
odors.

• The door on this appliance can be op ened from
either the left or th e right side. The unit is delivered
with the door opening on the left side. Should you
wish to open the d oor from the right, follow the
instructions ‘Re versing the door hinge’Install the
handle on the door if necessary.

INSTALLATION OF YOUR APPLIANCE

• The appliances are designed to be built-i n or
recessed or free standing installation.

• WARNING: Do not store or install the appliance
outdoors. The unit is for indoor use only.

• WARNING: Do no install the appliance in the
laundry. Avoid locating the unit in damp areas.

• Place your appliance on a floor that is strong
enough to support it when it is fully loaded.
Remove the transport legs before installation. Fix
installation legs (packed to your user m anual) if
you need to level the unit only.

• For freestanding installation, 100mm of space
between the back and sides of the unit are
suggested, which allows the proper air circulation
to cool the compressor and condenser for energy
saving. Even for built-in installation, it is a must to
keep 5mm space on each side and at the top to
ensure proper ser vice access and ventilation.
Take care that the air vent at the front of the
appliance must never be covered or blocked in
any way.

• Locate the unit awa y from direct sunlight and
sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and
heat sources may increase electrical
consumption. Extreme cold ambient temperatures
may also cause the unit not to perform properly.

• Plug the unit into an exclusive, easily accessible
plug socket. Any questions concerning power
and/or earthing should be directed towards a
qualified electrician or an authorized products
service centre.

• The appliance must be installed to all electrical,
connections in accordance with state and local
codes.

• IMPORTANT: HIGH HUMIDITY CLIMATE.
During periods of high humidity, some
condensation may appear on outside surfaces of
glass door. This condensation will disappear
when humidit y levels drop. For prevention, it is
advisable to install the appliance with sufficient
ventilation in a dry and/or an air-conditioned
place.

NOTE: The appliance must be positioned so

that the plug is accessible.

BUILT-UNDER INSTRUCTIONS

Make sure your installation does not block the front
ventilation grille.
worktops between 820 and 890mm in height. Remove
the adjustable ventilation grille screws and slide it to
the required height. Tighten the screws to lock the
grille in position.
If the unit is fully integrated to be installed for fitting
kitchen plinth, make sure that the ventilation gaps in
the plinth are at least 300 square centimeters and
remove the ventilation grilles, so that warm air can
disperse unhindered. Otherwise the appliance has to
work harder, resulting in an increase in electrici ty
consumption.

NOTE: When pushing the appliance into the niche,
make sure that the mai ns cable does not get trapped.

T he unit is designed to fit under

FULLY INTEGRATED BUILT-IN-COLUM N

INSTRUCTIONS

The unit door seals the installed unit almost
completely, so an air vent must be provided in the
base of the housing. Warmed air must be conducted
via the ventilation shaft to the rear wall of the housing
and then expelled upwards. The ventilation channels
should measure at least 200 square centimeters in
cross-section.
WARNING: To ensure the proper functioning of the
appliance, air vents should never be blocked or
covered.

BUILT-IN CABINET INST RUCTIONS

Make sure your installation does not block the front
ventilation grille.
close properly in the chosen location.

And be sure the door will open and

Have the receptacle and the circuit checked by a
qualified electrician to ensure that the socket is
grounded correctl y.

Note: In locations where there is frequent lightning,
it is advisable to use surge protectors.

Do not connect t he appliance to the mains electricity
supply by an extension lead. Extension leads do not
guarantee the required safety of the appliance (e.g.
danger of overheating).

The appliance must not be connected to an inverter
and must not be used with a plug adapter as these
can cause damage to the appliance’s electronic unit.

The cord must rest securely behind the appliance and
not be allowed to lie or hang unprotected.

WARNING:
THIS APPLIANCE MUST BE EARTHED.

INSTALLING THE HANDLE

IMPORTANT: Do not overtighten the screws & do not

use power tools to install the handle. Overtighten
screw causes glass breakage.

DESIGN 1 –

YOU CAN FIND THE DETAILED
INST ALLATION DRAWING IN THE
ATTACHM ENT

ELECTRICAL CONNECTION
WARNING:

result in the risk of electrical shock. If the power cord
is damaged, have it replaced by a qualified electrician
or an authorized service center.

All electrical work should be carried out by a suitabl y
qualified and com petent person in accordance with
local and national safety regulations.

Check that the voltage marked on the product
corresponds with your supply voltage.

Connect this appliance to a separate, at least 1 3A
circuit.

Connection should be made via a suitable switched
socket which is easily accessible. For extra safet y it is
advisable to install a residual current device (RCD)
with a trip current of 30mA.

Improper use of the grounded plug can

Locate the handle ①,o ver the fixing pins ③,of the
door and using the supplied allen key, tighten the
securing grub screws ②,to fix the handle.

DESIGN 2 –