DISPOSAL
CONNECTION TO THE MAINS SUPPLY
PRODUCT FEATURES
INSTALLATION
OPERATING YOUR APPLIANCE
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
WARRANTY
2
Please read this manual carefully before installing and starting up, and
store it in a safe place. If you pass on the product to another person, hand
over this instruction manual along with it.
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
FOR YOUR SAFETY
Read all instructions carefully, even if you are
quite familiar with the appliance.
The appliance is intended to be used for the
storage of wine. Use this appliance only as
described in this manual. Other uses not
recommended may cause fire, electric shock or
personal injury.
This appliance can be used by
children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge if
they have been given
supervision or instruction
concerning use of the
appliance in a safe way and
understand the hazards
involved. Children shall not
play with the appliance.
Cleaning and user
maintenance shall not be
made by children without
supervision.
Electrical devices are not toys. Always keep
the device out of the reach of children. Keep the
mains cord out of the reach of children. Do not
let the mains cord hang over the edge of the
table or worktop on which the appliance stands.
To protect against the risk of electric shock, DO
NOT IMMERSE the unit, cord, or plug in water
or spray any other liquid.
Unplug the appliance from the plug socket when
not in use, when moving from one location to
another and before cleaning.
To disconnect the appliance, grip the plug and
pull it from the wall outlet. Never pull by the cord.
WARNING: Please keep the appliance away
Code Rev. D 20140818 (IEC)
from substance, which can cause ignition. Do
not operate the appliance in the presence of
explosive and/or flammable fumes.
Do not place the appliance or any of its part near
an open flame, cooking or other heating
appliance.
Do not operate the appliance with a damage
cord or plug, if the product malfunctions, or if it is
dropped or damaged in any manner. If the
supply cord is damaged, it must be replaced by
the manufacturer, or an authorized service
centre or similarly qualified persons in order to
avoid a hazard.
The use of attachments not recommended by
the manufacturer may be hazardous.
Place the unit on a dry level surface.
Do not operate if the housing is removed or
damaged.
A loose fit between the AC outlet (receptacle)
and plug may cause overheating and a distortion
of the plug. Contact a qualified electrician to
replace loose or worn outlet.
Locate the unit away from direct sunlight and
sources of heat (stove, heater, radiator, etc.).
WARNING: This appliance is CFC- and HFC-
free and contains small quantities of Isobutane
(R600a) which is environmentally friendly, but
flammable. It does not damage the ozone layer,
nor does it increase the greenhouse effect. Care
must be taken during transportation and setting
up of the appliance that no parts of the cooling
system are damaged. Leaking coolant can ignite
and may damage the eyes.
In the event of any damage:
- Avoid open flames and anything which creates
a spark,
- Disconnect from the mains,
- Air the room in which the appliance is located
for several minutes and
- Contact the Service Department for advice.
The more coolant there is in an appliance, the
larger the room it should be installed in. In the
event of a leakage, if the appliance is in a small
room, there is the danger of combustible gases
building up. For every 8 g of coolant at least 1
cubic meter of room space is required. The
amount of coolant in the appliance is stated on
the data plate inside the appliance. It is
3
hazardous for anyone other than an Authorised
WARNING: To reduce the risk of fire,
electric shock or personal injury,
unplug or disconnect the appliance
from the power supply before
servicing.
Service Person to carry out servicing or repairs
to this appliance. In Queensland of Australia the
authorized person must hold a Gas Work
Authorisation for hydrocarbon refrigerants,
before carrying out servicing or repairs which
involve the removal of covers.
WARNING: Keep ventilation openings, in the
appliance enclosure or in the built-in structure,
clear of obstruction. No liability will be accepted
for any damage incurred owing to misuse of the
appliance or as a result of repairs carried out by
unqualified personnel. In this case neither the
guarantee nor any other liability claims will apply.
WARNING: Do not use mechanical devices or
other means to accelerate the defrosting
process, other than those recommended by the
manufacturer.
WARNING: Do not damage the refrigerant
circuit. Never use an appliance with a damaged
circuit.
WARNING: Do not use any electrical appliance
inside the food storage compartment of the
appliance, unless they are of the type
recommended by the manufacturer.
WARNING: To avoid a hazard due to instability
of the appliance, it must be fixed in accordance
with the instructions.
CAUTION: Please keep the products away from
Do not store explosive substances such as
This appliance is intended to be used in
Do not attempt to repair or replace any part of
Replace all panels after service before operating.
Use two or more people to move and install the
Never clean appliance parts with flammable
Code Rev. D 20140818 (IEC)
the fire or similar glowing substance before you
dispose the refrigerator.
aerosol cans with a flammable propellant in this
appliance.
household and similar applications such as
- staff kitchen areas in shops, offices and other
working environments;
- farm houses and by clients in hotels, motels
and other residential type environments;
- bed and breakfast type environments;
- catering and similar non-retail applications.
your appliance unless it is specifically
recommended in this manual. All other servicing
should be referred to a qualified technician.
appliance. Failure to do so can result in back or
other injury.
fluids. These fumes can create a fire hazard or
explosion. And do not store or use gasoline or
other flammable vapors and liquids in the vicinity
of this or any other appliance. The fumes can
create a fire hazard or explosion.
Do not connect or disconnect the electric plug
when your hands are wet.
It is recommended that a separate circuit,
serving only your appliance be provided. Use
receptacles that cannot be turned off by a switch
or pull chain.
If you have a lockable appliance, do not keep
the key near the appliance or within reach of
children.
SAVE THESE INSTRUCTIONS
If you are experiencing problems, check the
Troubleshooting Guide at the back of this manual. It
lists causes of minor operating problems that you
can correct by yourself.
DISPOSAL
Dispose of your appliance packaging properly.
Ensure that any plastic wrappings, bags etc. are
disposed of safely and kept out of the reach of
babies and young children. Danger of suffocation!
Refrigeration equipment must be properly disposed
of in a professional and appropriate way, in
accordance with the current local regulations and
laws which protects the environment this applies to
your old appliance and to your new unit once it has
reached the end of its service life.
WARNING: Please ensure that old, worn appliances
are rendered unusable before disposal by removing
the doors, removing the plug, cutting the network
cable, and removing or destroying any snap
fastenings or bolts. You will thus prevent children
from locking themselves in the appliance during play
(risk of suffocation) or endangering their lives in any
other way. DO NOT dispose of the appliance in
landfill as the insulation (Cyclopentane) and
refrigerant gas (R600a) contained in these
appliances are flammable.
Disposal instructions:
The appliance must not be disposed of in the
dustbin or with normal household rubbish.
The coolant circuit, particularly the heat
exchanger at the back/bottom of the unit, must
not be damaged.
4
The symbol on the product or its packaging
N e u tr a l
(B l u e )
Ea rth
(G reen/Y e llo w )
L iv e
(B r o w n )
indicates that this product is not to be handled
as normal household waste but is to be taken to
a recycling collection point for electrical and
electronic goods. By correctly disposing of this
product you are contributing to the protection of
the environment and to the health of your fellow
human beings. Improper disposal endangers
health and the environment. Further information
about the recycling of the product may be
obtained from your town hall, refuse collection
department or the store where you purchased
the product.
CONNECTION TO THE MAINS
SUPPLY
UK, IRL, HK, SINGAPORE
Check that the voltage marked on the product
corresponds with your supply voltage.
This product is fitted with a 13A plug complying with
BS1363. If this plug is unsuitable or needs to be
replaced, please note the following:
WARNING:
THIS APPLIANCE MUST BE EARTHED.
Important: The wires in the mains lead are coloured
in accordance with the following code:
GREEN/YELLOW - EARTH
BLUE - NEUTRAL
BROWN - LIVE
the EARTH and must be connected to the terminal
which is marked with the letter ‘E’ or by the earth
symbol or coloured GREENor
GREEN/YELLOW.
The BLUE wire is the NEUTRAL and must be
connected to the terminal which is marked with the
letter ‘N’ or coloured BLACK.
The BROWN wire is the LIVE wire and must be
connected to the terminal which is marked with the
Letter ‘L’ or coloured RED.
Always ensure that the plug cord grip is fastened
correctly.
If in doubt consult a qualified electrician who will be
pleased to do this for you. This product conforms to
EC Directive 92/31 /EEC with respect to
Electromagnetic Compatibility.
NON-REWIREABLE MAINS PLUG
If your appliance is supplied with a non-rewireable
plug fitted to the mains lead, you will find that it
incorporates a fuse, the value of which is indicated
either on the base of the plug or on the fuse carrier.
Should the fuse need replacing, you must use an
ASTA approved one (conforming to BS1362) of the
same rating.
If the fuse cover is lost, the plug must not be used
until a replacement is obtained from an electrical
supplier.
If you need to remove the plug, cut it from the mains
lead and immediately dispose of it. Never attempt to
re-use this plug or insert it into a socket outlet as
there is a very great risk of an electric shock.
This appliance is equipped with a plug fitted with a
13 amp fuse. Should the fuse fail, then it must be
replaced with an ASTA approved fuse (conforming
to BS1362) of the same rating. If you need to
replace the plug or if the plug is of the incorrect type
for your socket, remove it and replace it with an
appropriate type. Dispose of the old plug safely.
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The GREEN/YELLOW wire is
Code Rev. D 20140818 (IEC)
5
PRODUCT FEATURES
Built-in or Free-standing installation with single,
dual or three temperature zone, depending on
your model.
Continuously variable electronic temperature
control with digital display and touchpad input.
Temperature can be set from 5° to 22°C (40° to
72°F) for either compartment and can be
displayed in either Fahrenheit or Celsius degree.
Can be set to the long time storage maturing
temperature or a specific serving temperature
for red/white/sparkling wines.
Cooling and Heating to maintain the perfect
storaging and/or service condition.
Dynamic compressor type cooling to ensure
interior air circulation with even distribution of
temperature and humidity.
Soft white LED Interior Light with ON/OFF switch
– Function mode and Showcase mode.
Open-door and malfunction warning system.
Sabbath mode will allow the lights to remain off
during certain religious observances.
Temperature memory function - If power is
interrupted (power surge, breaker switch, etc.)
and then powered up again, the unit will operate
with the last temperature set-point.
Automatic defrosting with defrost water
evaporation.
Reversible tempered double/triple pane smoked
glass door protects your wine from UV light and
creates an attractive display with few
condensation and low noise.
Black coated matte steel outer frame and black
plastic interior liner offer lifetime performance
and stability. The black liner prevents excessive
light from damaging the maturity process.
Optional stainless steel-framed glass door with
stainless steel handle.
Optional roll-out and adjustable solid varnished
beech shelves allow for maximum convenience
and flexibility to accommodate various size
bottles.
Environmentally friendly refrigerant and foaming
insulation gas.
Optional security lock system with keys.
Optional humidity control system (Humidity Box).
Optional active charcoal air filter.
Code Rev. D 20140818 (IEC)
NOTE: Features and specifications are subject to
change without notice.
INSTALLATION
BEFORE USING YOUR APPLIANCE
Remove all exterior and interior packing. Clean
the interior surface with lukewarm water using a
soft cloth. The unit may have residual odors at
first, they will disappear as the unit cools.
Before connecting the appliance to the power
source, let it stand upright for at least 24 hours.
This will reduce the possibility of a malfunction in
the cooling system caused by handling during
transportation. During this time we recommend
that you leave the door open to clear any
residual odors.
The door on this appliance can be opened from
either the left or the right side. The unit is
delivered with the door opening on the left side.
Should you wish to open the door from the right,
follow the instructions ‘Reversing the door hinge’.
Install the handle on the door if necessary.
INSTALLATION OF YOUR APPLIANCE
The appliances are designed to be built-in or
WARNING: Do not store or install the appliance
WARNING: Do no install the appliance in the
Place your appliance on a floor that is strong
For freestanding installation, 100mm of space
recessed or free standing installation.
outdoors. The unit is for indoor use only.
laundry. Avoid locating the unit in damp areas.
enough to support it when it is fully loaded. To
level your unit, adjust the front leveling leg at the
bottom of the unit.
between the back and sides of the unit are
suggested, which allows the proper air
circulation to cool the compressor and
condenser for energy saving. Even for built-in
installation, it is a must to keep 5mm space on
each side and at the top to ensure proper
service access and ventilation. Take care that
6
the air vent at the front of the appliance must
A
(mm)
B
(mm) C (mm) D (mm)
15cm
Wide
148
150
75
450
30cm
Wide
295
300
110
460
60cm
Wide
595
600
110
460
NOTE: The appliance must be positioned so
that the plug is accessible.
never be covered or blocked in any way.
Locate the unit away from direct sunlight and
sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and
heat sources may increase electrical
consumption. Extreme cold ambient
temperatures may also cause the unit not to
perform properly.
Plug the unit into an exclusive, easily accessible
plug socket. Any questions concerning power
and/or earthing should be directed towards a
qualified electrician or an authorized products
service centre.
The appliance must be installed to all electrical,
plumbing, water and drain connections in
accordance with state and local codes.
IMPORTANT: HIGH HUMIDITY CLIMATE.
During periods of high humidity, some
condensation may appear on outside surfaces of
glass door. This condensation will disappear
when humidity levels drop. For prevention, it is
advisable to install the appliance with sufficient
ventilation in a dry and/or an air-conditioned
place.
BUILT-UNDER INSTRUCTIONS
Make sure your installation does not block the front
ventilation grille. The unit is designed to fit under
worktops between 820 and 890mm in height, using
the adjustable ventilation grille to ensure that the
feet are concealed from front view. Remove the
adjustable ventilation grille screws and slide it to the
required height. Tighten the screws to lock the grille
in position.
If the unit is fully integrated to be installed for fitting
kitchen plinth, make sure that the ventilation gaps in
the plinth are at least 300 square centimeters and
remove the ventilation grilles, so that warm air can
disperse unhindered. Otherwise the appliance has to
work harder, resulting in an increase in electricity
consumption.
NOTE: When pushing the appliance into the niche,
make sure that the mains cable does not get trapped.
Code Rev. D 20140818 (IEC)
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.