Dukane 8766 User Manual

Liquid Crystal Projector
Model 8766
USER'S MANUAL
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your Dukane 8766 Projector and keep the manual handy for future reference. Your
CAUTION
To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED NEC SERVICE PER­SONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information con­cerning the operation and maintenance of this unit has been provided. The information should be read carefully to avoid problems.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL TWO PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM­PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI­FIED NEC SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance-3. GSGV:
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
CAUTION
•Avoid displaying stationary images for a prolonged pe­riod of time. Doing so can result in these images being temporarily sustained on the surface of the LCD panel. If this should happen, continue to use your projector. The static background from previous images will disappear.
• Do not put the projector on its side when the lamp is turned on. Doing so may cause damage to the projector.
RF Interference
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Soluctions (America), Inc. in this manual. Failure to com­ply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar­antee that interference will not occur in a particular installa­tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with this equipment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal com­ponents.
5. Handle your projector carefully. Dropping or jarring can damage in­ternal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the
projector and the installation must be in accordance with any local building codes.
d. Please consult your dealer for more information.
E-2
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unob­structed to prevent the build-up of heat inside your projector. Allow at least 3 inches (10 cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.
Do not attempt to retrieve any objects that might fall into your pro­jector. Do not insert any metal objects such as a wire or screwdriver into your projector. If something should fall into your projector, dis­connect it immediately and have the object removed by a qualified NEC service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage to your eyes could result.
5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the lens is extensive, there­fore any kind of abnormal objects that can redirect light coming out of the lens, can cause unpredictable outcome such as fire or injury to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while the projector is on. Doing so can lead to melting of the cap and possibly burning your hands due to the heat emitted from the light output.
7. The projector is designed to operate on a power supply of 100-120 or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this requirement before attempting to use your projector.
8. Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or fire.
9. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.
10. Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
What's in the Box?
Make sure your box contains everything listed. If any pieces are miss­ing, contact your dealer. Please save the original box and packing materials if you ever need to ship your Dukane 8766 Projector.
Lens cap
Projector
O F
F V I D
E O
P O
S
W
-V
E
ID
R
E O
O
R
N G B
A U
TO
A D
J .
SELECT
PJ
PIC
T UR
E
H E
LP
A
F
S
R
P
E
EC
E Z E
T
P
M
I C
A
-
G
M
N
U I F
T
Y
E
V O
LU
M E
Remote control
Power cable
USB cable
String and rivet
RGB signal cable
CAUTION
1. Do not try to touch the ventilation outlet on the front as it can be­come heated while the projector is turned on.
2. Do no use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hanging on the wall can cause damage to the projector.
3. When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle to the projector cabinet are tight.
Insufficient tightening of the two screws could result in the projector falling and causing injury.
4. Enable High-Speed Fan mode if you continue to use the projector for consecutive days. (From the menu, select [Advanced] → [High Speed Fan Mode].)
5. Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
* While the Hour Glass icon appears.
* While the cooling fans are running. (The cooling fans continue
to work for 60 seconds after the projector is turned off).
Lamp Replacement
•To replace the lamp, follow all instructions provided on page E-30.
• Be sure to replace the lamp when the message "The lamp has
reached the end of its usable life. Please replace the lamp."
appears. If you continue to use the lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
• Allow a minimum of 60 seconds to elapse after turning off the pro­jector. Then turn off the main power switch, disconnect the power cable and allow 60 minutes to cool the projector before replacing the lamp.
E-3
Soft carrying case Carrying handle, Screw (M4⳯2)
Flathead screwdriver
User's Manual
TABLE OF CONTENTS
Important Information ..................................................... E-2
Safety Cautions ............................................................................................................... E-2
What's in the Box? .......................................................................................................... E-3
INTRODUCTION .............................................................. E-5
Introduction to the Projector ........................................................................................... E-5
Part Names of the Projector ............................................................................................ E-6
Attaching the lens cap ................................................................................................. E-6
Attaching the supplied carrying handle ........................................................................ E-6
Top Features ................................................................................................................ E-7
Terminal Panel Features ............................................................................................... E-8
Part Names of the Remote Control .............................................................................. E-9
Battery Installation ................................................................................................. E-10
Remote Control Precautions .................................................................................. E-10
Operating Range for Wireless Remote Control ...................................................... E-10
INSTALLATION AND CONNECTIONS ....................................... E-11
Setting Up the Screen and the Projector ....................................................................... E-11
Selecting a Location .................................................................................................. E-11
Throw Distance and Screen Size ............................................................................... E-12
Making Connections ...................................................................................................... E-13
Connecting Your PC or Macintosh Computer ............................................................ E-13
To connect SCART output (RGB) ............................................................................... E-14
Connecting an External Monitor ................................................................................ E-14
Connecting Your DVD Player ..................................................................................... E-15
Connecting Your VCR or Laser Disc Player ............................................................... E-16
Connecting the Supplied Power Cable ....................................................................... E-16
PROJECTING AN IMAGE (BASIC OPERATION) ........................... E-17
Tur ning on the Projector ................................................................................................ E-17
Selecting a Source ......................................................................................................... E-18
Adjusting the Picture Size and Position ......................................................................... E-18
Correcting the Vertical Keystone Distortion ................................................................... E-19
Optimizing RGB Picture Automatically .......................................................................... E-20
Tur ning Up or Down Volume ......................................................................................... E-20
Tur ning off the Projector ............................................................................................... E-20
CONVENIENT FEATURES................................................... E-21
Using the Remote Mouse Function ............................................................................... E-21
Connecting to your computer for the remote mouse function ................................... E-21
When using the USB Port .......................................................................................... E-21
Switching operation mode between computer and projector ..................................... E-21
Tur ning Off the Image and Sound .................................................................................. E-22
Freezing a Picture .......................................................................................................... E-22
Enlarging and Moving a Picture ..................................................................................... E-22
Getting the Information ................................................................................................. E-22
USING ON-SCREEN MENU ................................................. E-23
Basic Menu Operation ................................................................................................... E-23
Using the Menus ....................................................................................................... E-23
List of Menu Items ........................................................................................................ E-24
Menu Elements ............................................................................................................. E-25
Menu Descriptions & Functions .................................................................................... E-26
Picture ....................................................................................................................... E-26
Brightness/Contrast/Sharpness/Color/Hue ............................................................ E-26
Picture Management .............................................................................................. E-26
Image ........................................................................................................................ E-26
Enabling Auto Keystone <Auto Keystone> ............................................................. E-26
Correcting Vertical Keystone Distortion Manually <Keystone> .............................. E-26
Saving Vertical Keystone Correction <Keystone Save> .......................................... E-26
Selecting Aspect Ratio [Aspect Ratio] ................................................................... E-27
Adjusting the Vertical Position of Image [Cinema Position](for Cinema only) ....... E-27
Setup ......................................................................................................................... E-27
Selecting Lamp Mode [Lamp Mode] ...................................................................... E-27
Selecting Menu Language [Language] ................................................................... E-27
Selecting Menu Color [Menu Color Select] ............................................................ E-27
Selecting Menu Display Time [Menu Display Time] ............................................... E-27
Selecting a Color or Logo for Background [Background] ...................................... E-27
Selecting Projector Orientation [Orientation] ......................................................... E-27
Advanced ................................................................................................................... E-27
Disabling the Cabinet Buttons [Control Panel Key Lock] ........................................ E-27
Enabling Power Management [Power Management] ............................................. E-27
Enabling High Speed Fan Mode [High Speed Fan Mode] ....................................... E-27
Selecting Signal Format [Signal Select] ................................................................. E-28
Page2 .................................................................................................................... E-28
Selecting Noise Reduction Level (not available for RGB) ....................................... E-28
Enabling Auto Adjust [Auto Adjust] ....................................................................... E-28
Adjusting Position/Clock (when Auto Adjust is off) ............................................... E-28
Information ................................................................................................................ E-28
Default ....................................................................................................................... E-29
MAINTENANCE ............................................................. E-30
Replacing the Lamp ...................................................................................................... E-30
Cleaning ........................................................................................................................ E-31
Cleaning or Replacing the Filter ................................................................................. E-31
Cleaning the Cabinet and the Lens ............................................................................. E-31
TROUBLESHOOTING ........................................................ E-32
Power Indicator ............................................................................................................. E-32
Status Indicator ............................................................................................................. E-32
Lamp Indicator .............................................................................................................. E-32
Common Problems & Solutions .................................................................................... E-33
SPECIFICATIONS ........................................................... E-34
APPENDIX ................................................................... E-35
Cabinet Dimensions ...................................................................................................... E-35
Pin Assignments of D-Sub RGB Input Connector .......................................................... E-35
Compatible Input Signal List ......................................................................................... E-36
E-4
INTRODUCTION
Introduction to the Projector
This section introduces you to your new Dukane 8766 Projector and describes the features and controls.
Congratulations on Your Purchase of The Projector
The Dukane 8766 is one of the very best projectors available today. The Dukane 8766 enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD player, docu­ment camera, or a laser disc player. You can use the projector on a tabletop or cart, you can use the projec­tor to project images from behind the screen, and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.
*1Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the pro­jector and the installation must be in accordance with any local building codes. Please consult your dealer for more information.
Features you'll enjoy:
• Auto vertical keystone correction up to +/- 30 degrees
• Low level noise
• Short focal length lens
• 200W lamp (160W Eco mode)
• Direct keys for source selection
• New Color Management system
• New menu design improves operability
• Advanced intelligent pixel blending technology-
an extremely accurate image compression technology - of­fers a crisp image with UXGA (16001200) resolution
• Supports most IBM VGA, SVGA, XGA , SXGA/UXGA Macintosh, component signal (YCbCr/ YPbPr) or any other RGB signals within a horizontal frequency range of 24 to 100 kHz and a vertical frequency range of 50 to 120 Hz. This includes NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 stan­dard video signals.
.
About this user's manual
The fastest way to get started is to take your time and do ev­erything right the first time. Take a few minutes now to review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find an over­view. If the section doesn't apply, you can skip it.
• IBM is a trademark or registered trademark of International Business Machines Corporation.
• Mac and PowerBook are trademarks of Apple Computer, Inc., regis­tered in the U.S. and other countries.
•Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks of Microsoft Corporation.
• Other product and company names mentioned in this user’s manual may be the trademarks or registered trademarks of their respective holders.
NOTE: Composite video standards are as follows: NTSC: U.S. TV standard for video in U.S. and Canada. PAL: TV standard used in Western Europe. PAL-N: TV standard used in Argentine, Paraguay and Uruguay. PAL-M: TV standard used in Brazil. PAL60: TV standard used for NTSC playback on PAL TVs. SECAM: TV standard used in France and Eastern Europe. NTSC4.43: TV standard used in Middle East countries.
• The supplied remote control can be used without a cable, and you can even use the remote control to operate your PC's mouse wirelessly from across the room with the built-in remote mouse func­tion.
•You can control the projector with a PC using the PC Control port.
• The contemporary cabinet design is light, compact, easy to carry, and complements any office, boardroom or auditorium.
E-5
Part Names of the Projector
Monaural Speaker (1W)
Lamp Cover (See page E-30)
Lamp Cover Screw
Ventilation (outlet) Heated air is exhausted from here
Adjustable Tilt Foot Lever (See page E-18)
Adjustable Tilt Foot (See page E-18)
Ventilation (inlet) / Filter Cover (inlet)
Main Power Switch When you plug the supplied power cable into an active wall outlet and turn on the Main Power switch, the POWER indicator turns orange and the projector is in standby mode. (See page E-17)
Controls (See page E-7)
Zoom Lever
Focus Ring
Lens
Adjustable Tilt Foot Lever (See page E-18)
Adjustable Tilt Foot (See page E-18)
Lens Cap
Remote Sensor (See page E-10)
Remote Sensor (See page E-10)
Built-in Security Slot ( )*
AC Input Connect the supplied power cable's two­pin plug here, and plug the other end into an active wall outlet. (See page E-16)
* This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is
trademarked and owned by Kensington Microware Inc.
Attaching the lens cap
To attach the lens cap to the bottom with the supplied string and rivet:
1. Thread the string through the hole on the lens cap and then tie a knot in the string.
2. Use the rivet to attach the string to the bottom of the projector.
Attaching the supplied carrying handle
You can carry the projector by attaching the supplied carrying handle securely to the projector. To attach the supplied carrying handle, use the supplied flathead screw­driver and two screws.
CAUTION: When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle to the projector cabinet are tight.
E-6
Top Features
765 10
8
2 3 4 11
1319 12
1. POWER Button (ON / STAND BY)( ) Use this button to turn the power on and off when the main power is supplied and the projector is in standby mode. To turn on the projector, press and hold this button for a minimum of two seconds. To turn off the projector, press this button twice.
2. POWER Indicator When this indicator is green, the projector is on; when this indicator is orange, it is in standby mode. See the Power Indicator section on page E-32 for more details.
3. STATUS Indicator If this light blinks red rapidly, it indicates that an error has occurred, the lamp cover is not attached properly or the projector has over­heated. If this light remains orange, it indicates that you have pressed a cabinet key while the Control Panel Key Lock is enabled. See the Status Indicator section on page E-32 for more details.
4. LAMP Indicator If this light blinks red rapidly, it's warning you that the lamp has reached the end of its usable life. After this light appears, replace the lamp as soon as possible (See page E-30). If this is lit green continually, it indicates that the lamp mode is set to Eco. See the Lamp Indicator section on page E-32 for more details.
5. VIDEO Button Press this button to select a video source from a VCR, DVD player, laser disc player or document camera.
6. S-VIDEO Button Press this button to select an S-Video source from a VCR.
7. RGB Button Press this button to select an RGB source from computer or compo­nent equipment connected to your RGB port.
8. AUTO ADJ. Button Use this button to adjust Position-H/V and Pixel Clock/Phase for an optimal picture (See page E-20).
9. Source Indicators When one of the RGB, VIDEO or S-VIDEO input is selected, the corresponding source indicator lights.
10. MENU Button Displays the menu.
11. SELECT GHFE / Volume Buttons GH : Use these buttons to select the menu of the item you wish to
adjust.
FE : Use these buttons to change the level of a selected menu item.
A press of the E button executes the selection. When no menus appear, these buttons work as a volume control.
When an image is magnified, the SELECT GHFE button moves the image.
12. ENTER Button Executes your menu selection and activates items selected from the menu.
13. CANCEL Button Pressing this button will return to the previous menu. While you are in the main menu, pressing this button will close the menu.
E-7
Te rminal Panel Features
712 8
3456
1. RGB IN / Component Input Connector (Mini D-Sub 15 Pin) Connect your computer or other analog RGB equipment such as IBM compatible or Macintosh computers. Use the supplied RGB cable to connect to your computer. This also serves as a component input connector that allows you to connect a component video output of component equipment such as a DVD player. This connector also supports SCART output signal. See page E-14 for more details.
2. RGB AUDIO Input Mini Jack (Stereo Mini) This is where you connect the audio output from your computer or DVD player when connected to the RGB input. A commercially avail­able audio cable is required.
3. RGB OUT Connector (Mini D-Sub 15 Pin) You can use this connector to loop your computer image to an exter­nal monitor from the RGB input source. This connector outputs RGB signal in standby mode.
4. AUDIO OUT Mini Jack (Stereo Mini) You can use this jack to output sound from the currently selected source (RGB, VIDEO or S-VIDEO). Output sound level can be ad­justed in accordance with the sound level of the internal speaker.
5. S-VIDEO IN Connector (Mini DIN 4 Pin) Here is where you connect the S-Video input from an external source like a VCR.
NOTE: S-Video provides more vivid color and higher resolution than the tra­ditional composite video format.
S-VIDEO AUDIO Input Jacks R/L (RCA) These are your left and right channel audio inputs for stereo sound from an S-Video source.
6. VIDEO IN Connector (RCA) Connect a VCR, DVD player, laser disc player, or document camera here to project video.
VIDEO AUDIO Input Jacks R/L (RCA) These are your left and right channel audio inputs for stereo sound from a Video source.
7. USB (PC) Port (Type B) Connect this port to the USB port (type A) of your PC using the sup­plied USB cable. You can operate your computer's mouse functions from the remote control.
8. PC CONTROL Port (DIN 8 Pin) For service personnel only.
E-8
Part Names of the Remote Control
NOTE: If you are using a Macintosh computer, you can click either the CANCEL (right-click) or ENTER (left-click) button to activate the mouse.
1
2
3
8 7
9
12
10
11
OFF ON
4
5
VIDEO
POWER
S-VIDEO
AUTO ADJ.
RGB
6
N
U
E
M
SELECT
E
N
T
E
R
L
E
C
N
A
C
PJ
13
14
16
19
PICTURE
HELP
ASPECT
FREEZE PIC-MUTE
MAGNIFY
VOLUME
15
18 17
20
1. Infrared Transmitter Direct the remote control toward the remote sensor on the projector cabinet.
2. LED Flashes when any button is pressed.
3. POWER ON Button When the main power is on, you can use this button to turn your projector on.
NOTE: To turn on the projector, press and hold the POWER ON button for a minimum of two seconds.
4. POWER OFF Button You can use this button to turn your projector off.
NOTE: To turn off the projector, press the POWER OFF button twice.
5. VIDEO Button Press this button to select a video source from a VCR, DVD player, laser disc player or document camera.
6. S-VIDEO Button Press this button to select an S-Video source from a VCR.
7. RGB Button Press this button to select RGB input.
8. AUTO ADJ. Button Use this button to adjust an RGB source for an optimal picture. See page E-20.
9. MENU Button Displays the menu for various settings and adjustments.
10. SELECT GHFE (Mouse) Button When you are in the Computer mode, these buttons work as a com­puter mouse. When you are in the Projector mode, which is indicated by lighting the PJ button. See page E-21.
GH : Use these buttons to select the menu of the item you wish
to adjust.
FE : Use these buttons to change the level of a selected menu
item. A press of the E button executes the selection. When no menus appear, these buttons work as a volume control.
When an image is magnified, the SELECT GHFE button moves the image.
11. ENTER (Left Click) Button When you are in the Computer mode, this button works as the mouse left button. When this button is pressed and held for a minimum of 2 seconds, the drag mode is set. When you are in the Projector mode, which is indicated by lighting the PJ button: Use this button to enter your menu selection. It works the same way as the ENTER button on the cabinet. See page E-7.
12. CANCEL (Right Click) Button When you are in the Computer mode, this button works as the mouse right button. When you are in the Projector mode, which is indicated by lighting the PJ button: It works the same way as the CANCEL button on the cabinet. See page E-7.
13. PJ Button Press this button to switch the SELECT, CANCEL, and ENTER but­tons between the Projector mode (lit red) and the Computer mode. Press this button or any one of the POWER ON/OFF, MENU, AS­PECT, HELP, MAGNIFY, buttons to switch to the Projector mode and the PJ button lights red. To switch back to the Computer mode, press the PJ button again. See page E-21.
14. PICTURE Button Press this button to display the Picture adjustement screen such as Brightness, Contrast, Sharpness, Color and Hue. See page E-26.
15. ASPECT Button Press this button to display the Aspect Ratio select screen. See page E-27.
16. HELP Button Provides the set information.
17. FREEZE Button This button will freeze a picture. Press again to resume motion.
18. PIC-MUTE Button This button turns off the image and sound for a short period of time. Press again to restore the image and sound.
19. MAGNIFY (+)(–) Button Use this button to adjust the image size up to 400%. The image is magnified about the center of the screen. See page E-
22.
20. VOLUME (+)(–) Button Press (+) to increase the volume and (–) to decrease it.
NOTE: The default is the Computer mode, which allows you to use the SELECT, CANCEL, and ENTER buttons as your computer mouse. When the POWER ON/ OFF, MENU, ASPECT, HELP, or MAGNIFY button is pressed, the PJ button lights red to indicate that you are in the Projector mode. If no buttons are pressed within 60 seconds, the light goes out and the Projector mode is canceled.
E-9
Battery Installation
1. Press firmly and slide the battery cover off.
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the batteries.
• Do not place the batteries upside down.
• Do not use new and old batteries together, or use different types of batteries together
2. Remove both old batteries and install new ones (AA). Ensure that you have the batteries' polarity (+/-) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place. Do not mix different types of batteries or new and old batteries.
Note on Remote Control Operation:
If you press and hold the SELECT GHFE button while installing new batteries, the remote control may fail to work properly. Should this happen, remove the batteries and then install them again without touching the SELECT button.
Operating Range for Wireless Remote Control
7m/22 feet
˚
30
˚
30
Remote sensor on projector cabinet
• The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet.
• The projector will not respond if there are objects between the re­mote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
7m/22 feet
30
30
Remote control
˚
˚
E-10
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect video and audio sources.
1
Your projector is simple to set up and use. But before you get started, you must first:
Set up a screen and the projector.
1 2
Connect your computer or video equip­ment to the projector. See page E-13 – 16.
3
Connect the supplied power cable. See page E-16.
2
NOTE: Ensure that the power cable and any other cables are disconnected before moving the projector. When moving the projector or when it is not in use, cover the lens with the lens cap.
To the wall outlet.
3
Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 21" (0.53 m) measured diagonally when the projector is roughly 27.6 inches (0.7 m) from the wall or screen. The largest the image can be is 300" (7.6 m) when the projector is about 393.7 inches (10 m) from the wall or screen. Use the drawing below as a guide.
Screen size (Unit: cm/inch)
609.6(W)X457.2(H)/240(W)X180(H)
365.8(W)X274.3(H)/144(W)X108(H)
304.8(W)X228.6(H)/120(W)X90(H)
243.8(W)X182.9(H)/96(W)X72(H)
203.2(W)X152.4(H)/80(W)X60(H)
162.6(W)X121.9(H)/64(W)X48(H)
121.9(W)X91.4(H)/48(W)X36(H)
81.3(W)X61.0(H)/32(W)X24(H)
61.0(W)X45.7(H)/24(W)X18(H)
50.8(W)X38.1(H)/20(W)X15(H)
42.7(W)X32(H)/17(W)X13(H)
Lens center
487.7(W)X365.8(H)/192(W)X144(H)
406.4(W)X304.8(H)/160(W)X120(H)
180"
150"
120"
100"
80"
60"
40"
30"
25"
21"
0.7/27.6"
0.8/31.5"
1.0/39.4"
2.0/78.7"
1.3/51.2"
2.7/106.3"
240"
200"
3.4/133.9"
300"
4.0/157.5"
Screen Size
5.1/200.8"
6.1/240.2"
6.7/263.8"
8.1/318.9"
10.1/397.6"
E-11
Distance (Unit: m/inch)
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
Distance Chart
Screen Height
Screen Width
Screen Diagonal
Screen center
(B)
B = Vertical distance between lens center and screen center C = Throw distance D = Vertical distance between lens center and top of screen (bottom of screen for desktop) α = Throw angle
NOTE: Distances may vary +/-5%.
Screen Size B C
inch
17 20 24 32 48 58 64 67 72 80
96 120 144 160 168 192 216 240
inch
13 15 18 24 36 43 48 50 54 60 72
90 108 120 126 144 162 180
inch
21 25 30 40 60 72 80 84
90 100 120 150 180 200 210 240 270 300
(D)
Throw Angle (α)
Wide – TeleDiagonal Width Height
inch
inch
––– - 29
5
29 - 35
6
35 - 42
7
47 - 57
10
71 - 86
15
86 - 103
17
96 - 115
19
101 - 121
20
108 - 129
22
120 - 144
24
144 - 173
29
181 - 217
36
217 - 260
44
241 - 290
48
253 - 304
51
290 - 348
58
326 - 391
65
363 - 400
73
Screen Bottom
Lens Center
1 1 2 2 3 4 5 5 5 6 7 9
)
α
Wide – Tele
degree
––– - 10.0
11.8 - 9.9
11.7 - 9.8
11.6 - 9.7
11.5 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
Screen Size B C
mm 427 508 610
813 1219 1463 1626 1707 1829 2032 2438 3048 3658 4064 4267 4877 5486 6096
mm 320 381 457 610
914 1097 1219 1280 1372 1524 1829 2286 2743 3048 3200 3658 4115 4572
mm 533 635
762 1016 1524 1829 2032 2134 2286 2540 3048 3810 4572 5080 5334 6096 6858 7620
mm
130 150 180 250 370 440 490 520 550 610 740
920 1110 1230 1290 1470 1660 1840
Throw Distance (C
D D
inch
10 12 12 14 16 17
Wide – TeleDiagonal Width Height
mm ––– - 740 740 - 880 890 - 1070
1200 - 1440 1810 - 2180 2180 - 2620 2430 - 2920 2550 - 3060 2740 - 3290 3050 - 3660 3660 - 4400 4590 - 5510 5510 - 6610 6130 - 7350 6440 - 7720 7360 - 8830 8290 - 9940 9210 -11050
mm
110 120 120 130 150 180 220 270 300 310 350 400 440
30 40 40 60 90
α
Wide – Tele
degree
––– - 10.0
11.8 - 9.9
11.7 - 9.8
11.6 - 9.7
11.5 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
WARNING * Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your dealer for more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely dam­aged.
• Do not use the projector where temperatures vary greatly. The pro­jector must be used at temperatures between 32˚F (0˚C) and 95˚F (35˚C).
• Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.
• Ensure that you have adequate ventilation around your projector so heat can dissipate. Do not cover the vents on the side or the front of the projector.
Reflecting the Image
Using a mirror to reflect your projector's image enables you to enjoy a much larger image. Contact your dealer if you need a mirror. If you're using a mirror and your image is inverted, use the MENU and SELECT buttons on your projector cabinet or your remote control to correct the orientation. (See page E-27.)
E-12
Loading...
+ 26 hidden pages