Dukane 8762 User Manual

Portable LCD Projector
Models 8762
User's Manual
• Digital Light Processing and DLP are trademarks of Texas Instruments.
• IBM is a trademark or registered trademark of International Business Machines Corporation.
• Macintosh, Mac OS X and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
• Other product and company names mentioned in this user's manual may be the trademarks or registered trade­marks of their respective holders.
NOTES
(1) The contents of this guide may not be reprinted in part or whole without permission.
(2) The contents of this guide are subject to change without notice.
(3) Great care has been taken in the preparation of this manual; however, should you notice any questionable points,
errors or omissions, please contact us.
(4) Notwithstanding article (3), Dukane will not be responsible for any claims on loss of profit or other matters deemed to
result from using the Projector.

Important Information

Safety Cautions
Precautions
Please read this manual carefully before using your 8762 projector and keep the manual handy for
future reference. Your serial number is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided. The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS CAN BE FULLY INSERTED.
DOC Compliance Notice (for Canada only)
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance-3. GSGV (for Germany only):
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
Disposing of your used product
EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes projectors and their electrical accessories or lamps. When you dispose of such products, please follow the guidance of your local authority and/or ask the shop where you purchased the product. After collecting the used products, they are reused and recycled in a proper way. This effort will help us reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human health and the environment at the minimum level. The mark on the electrical and electronic products only applies to the current European Union Member States.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
i
Important Information
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Solutions (America), Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radi­ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with this equipment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings.
Installation
• Do not place the projector in the following conditions:
- on an unstable cart, stand, or table.
- near water, baths or damp rooms.
- in direct sunlight, near heaters or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- on a sheet of paper or cloth, rugs or carpets.
• If you wish to have the projector installed on the ceiling:
- Do not attempt to install the projector yourself.
- The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury.
- In addition, the ceiling must be strong enough to support the projector and the installation must be in accor­dance with any local building codes.
- Please consult your dealer for more information.
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
10˚
ii
Important Information
Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow at least 4 inches (10cm) of space between your projector and a wall.
• Do not try to touch the ventilation outlet on the right front (when seen from the front) as it can become heated while the projector is turned on and immediately after the projector is turned off.
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your project. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified service personnel.
• Do not place any objects on top of the projector.
• Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
• The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power supply fits this requirement before attempting to use your projector.
• Do not look into the lens while the projector is on. Serious damage to your eyes could result.
•Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause unpre­dictable outcome such as fire or injury to the eyes.
• Do not cover the lens with the black lens cap or equivalent while the projector is on. Doing so can lead to melting of the cap and possibly burning your hands due to the heat emitted from the light output.
• Do not place any objects, which are easily affected by heat, in front of the projector lens or a projector exhaust vent. Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the light output and exhaust.
• Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire.
- Do not use any power cables than the supplied one.
- Do not bend or tug the power cable excessively.
- Do not place the power cable under the projector, or any heavy object.
- Do not cover the power cable with other soft materials such as rugs.
- Do not heat the power cable
- Do not handle the power plug with wet hands.
•Turn off the projector, unplug the power cable and have the object removed by a qualified NEC service personnel under the following conditions:
- When the power cable or plug is damaged or frayed.
- If liquid has been spilled into the projector, or if it has been exposed to rain or water.
- If the projector does not operate normally when you follow the instructions described in this user's manual.
- If the projector has been dropped or the cabinet has been damaged.
- If the projector exhibits a distinct change in performance, indicating a need for service.
- If the projector is not to be used for an extended period of time.
• Disconnect the power cable and any other cables before carrying the projector
•Turn off the projector and unplug the power cable before cleaning the cabinet or replacing the lamp.
CAUTION
• Do no use the tilt-foot for purposes other than originally intended. Misuses such as using the tilt foot to carry or hang (from the wall or ceiling) the projector can cause damage to the projector.
• Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside the soft case could be damaged.
• Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select [Setup - Options] [Fan Mode] [High].)
• Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable.
• Do not turn off the AC power for 60 seconds after the lamp is turned on and while the POWER indicator is blinking green. Doing so could cause premature lamp failure.
iii
Important Information
Remote Control Precautions
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
Do not heat, take apart, or throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries' polarity (+/–) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
Lamp Replacement
•To replace the lamp, follow all instructions provided on page 47 to 49.
Be sure to replace the lamp when the message [The lamp has reached the end of its usable life. Please replace the lamp.] appears. If you continue to use the lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
A Lamp Characteristic
The projector has a high-pressure mercury lamp as a light source. A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly turning the lamp on and off will increase the possibility of its lower brightness.
CAUTION:
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass fragments could fall if the lamp has been burned out.
iv

Table of Contents

Important Information ...........................................................................i
1. Introduction........................................................................................ 1
What's in the Box? ........................................................................................................ 1
Introduction to the Projector ......................................................................................... 2
Part Names of the Projector ......................................................................................... 4
Top Features ........................................................................................................... 6
Te r minal Panel Features ......................................................................................... 6
Part Names of the Remote Control .............................................................................. 7
Battery Installation ............................................................................................. 8
Remote Control Precautions .............................................................................. 8
Operating Range for Wireless Remote Control.................................................. 8
2. Installation and Connections ......................................................... 9
Setting Up the Screen and the Projector ...................................................................... 9
Selecting a Location................................................................................................ 9
Throw Distance and Screen Size.......................................................................... 10
Making Connections ................................................................................................... 12
Connecting Your PC or Macintosh Computer........................................................ 12
To connect SCART output (RGB) ......................................................................... 13
Connecting Your DVD Player with Component Output.......................................... 14
Connecting Your VCR or Laser Disc Player .......................................................... 15
Connecting the Supplied Power Cable ................................................................. 16
3. Projecting an Image (Basic Operation)...................................... 17
Tur ning on the Projector ............................................................................................. 17
Note on Startup Screen (Menu Language Select screen) .................................... 18
Selecting a Source ..................................................................................................... 19
Adjusting the Picture Size and Position ...................................................................... 20
Adjusting Focus Manually........................................................................................... 24
Correcting Keystone Distortion Manually ................................................................... 25
Optimizing RGB Picture Automatically ....................................................................... 26
Adjusting Volume Up or Down .................................................................................... 26
Tur ning off the Projector ............................................................................................. 27
After Use..................................................................................................................... 27
v
Table of Contents
4. Convenient Features ...................................................................... 28
Tur ning Off the Image and Sound............................................................................... 28
Freezing a Picture....................................................................................................... 28
Changing Lamp Mode ................................................................................................ 28
Preventing the Unauthorized Use of the Projector ..................................................... 28
Using the Optional Remote Mouse Receiver ............................................................. 31
5. Using On-Screen Menu ................................................................. 32
Using the Menus......................................................................................................... 32
Menu Elements........................................................................................................... 34
List of Menu Items ...................................................................................................... 35
Menu Descriptions & Functions [Picture].................................................................... 37
Menu Descriptions & Functions [Image Options] ....................................................... 38
Menu Descriptions & Functions [Setup] ..................................................................... 40
[Setup - General]................................................................................................... 40
[Setup - Installation] .............................................................................................. 41
[Setup - Options] ................................................................................................... 43
Menu Descriptions & Functions [Information] ............................................................. 44
Menu Descriptions & Functions [Reset] ..................................................................... 45
6. Maintenance .................................................................................... 46
Cleaning the Lens and the Focus Sensor ................................................................. 46
Cleaning the Cabinet ................................................................................................. 46
Replacing the Lamp................................................................................................... 47
7. Appendix ........................................................................................... 50
Troubleshooting ......................................................................................................... 50
Specifications ............................................................................................................ 53
Cabinet Dimensions .................................................................................................. 55
Pin Assignments of D-Sub COMPUTER Input Connector ........................................ 56
Compatible Input Signal List ...................................................................................... 57
PC Control Codes and Cable Connection ................................................................. 58
Troubleshooting Check List........................................................................................ 59
TravelCare Guide ....................................................................................................... 61
vi

1. Introduction

What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your projector.
Projector
Lens cap
(24F41351)
Power cable (US: 7N080204)
(EU: 7N080008)
SELECT
FOCUS
AUTO ADJ.
SOURCE
ON/STAND BY
POWER
STATUS
LAMP
Soft case
(24BS7551)
OFF
FOCUS
POWER
PIC-MUTE
ON
MENU
PAGE
UP
DOWN
ENTER
L-CLICK
VIDEO
EXIT
MOUSE
S-VIDEO
COMPUTER
R-CLICK
VOLUME
LAMP MODE
AUTO ADJ.
ASPECT
PICTURE
HELP
FREEZE
VGA signal cable
(7N520054)
Remote control (7N900681)
Batteries (AAA⳯2)
1
1. Introduction
Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
Congratulations on Your Purchase of the Projector
This projector is one of the very best projectors available today. The projector enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD player, document camera, or a laser disc player. You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen, and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.
1
Do not attempt to mount the projector on a ceiling yourself.
*
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accor­dance with any local building codes. Please consult your dealer for more information.
Features you'll enjoy:
•Auto Focus function
When you turn on the power, change the zoom or reposition the projector, the Auto Focus function will work instantly.
The focus sensor on the projector detects the distance to the screen and automatically adjusts the focus of an image as well as reducing the required set-up time.
•Auto vertical keystone correction up to +/– 16 degrees
Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white
screen material
Direct Power Off
The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even when projecting an image) using a power strip equipped with a switch and a breaker.
Also, the power cable can be removed immediately after turning off the projector.
HDTV (1080i, 720p) and SDTV (576p, 480p) compatibility
Integrated de-interlace video processing technology
Display popular wide screen and full screen aspect ratios – 16:9 and 4:3
Built-in speaker for an integrated audio solution
High resolution display - up to SXGA+ compatible, XGA native resolution.
Multiple video mode selections (depending on your source)
Safety protect by Security function
Security feature prevents unauthorized individuals from displaying images.
•You can control the projector with a PC or control system using the PC Control port.
Easy set up and operation
The contemporary cabinet design is light, compact and complements any office, boardroom or Auditorium.
2
1. Introduction
About this user's manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find an overview. If the section doesn't apply, you can skip it.
3
Part Names of the Projector

Front/Top

Adjustable Tilt Foot Button
page 21)
(
1. Introduction
Zoom Lever
(
page 22)
SELECT
FOCUS
AUTO ADJ.
SOURCE
Controls (
page 6)
ON/STAND BY
POWER
STATUS
LAMP
Remote sensor
(
page 8)
Lens
Built-in Security Slot ( )*
Monaural Speaker (1W)
Focus sensor
(→ page 22, 46)
Ventilation (outlet) Heated air is exhausted from here.
Lens Cap
Adjustable Tilt Foot (
page 21)
* This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.

Rear

Te r minal Panel
(→ page 6)
LAMP
STATUS
POWER
ON/STAND BY
COMPUTER IN
SOURCE
AUTO ADJ.
VIDEO IN
S-VIDEO IN
FOCUS
AUDIO IN
PC CONTROL
SELECT
Ventilation (inlet)
AC Input Connect the supplied power cable's three-pin plug here, and plug the other end into an active wall outlet. (→ page 16)
4

Bottom

Lamp Cover (
page 47)
Rear foot
(→ page 21)
1. Introduction
Rear foot (→ page 21)
5

Top Features

4
LAMP
STATUS
POWER
3
ON/STAND BY
1
5
SOURCE AUTO ADJ. FOCUS
1. Introduction
89
6 7
SELECT
2
1. POWER Button (ON / STAND BY) ( ) ( page 17,
27)
2. POWER Indicator ( page 16, 17, 27, 50)
3. STATUS Indicator ( page 50)
4. LAMP Indicator ( page 47, 50)
5. SOURCE Button ( page 19)
6. AUTO ADJ. Button ( page
26)

Te r minal Panel Features

1 3 4 52
COMPUTER IN PC CONTROLAUDIO INS-VIDEO INVIDEO IN
10
7. FOCUS Button ( page 24)
8. MENU Button
9. SELECT / Volume / Keystone  But- tons
10. ENTER Button
11. EXIT Button
11
1. COMPUTER IN/ Component Input Connector (Mini
D-Sub 15 Pin) ( page 12, 13, 14)
2. VIDEO IN Connector (RCA) ( page 15)
3. S-VIDEO IN Connector (Mini DIN 4 Pin)
( page
4. AUDIO IN Mini Jack (Stereo Mini) ( page 12, 14)
15)
5. PC CONTROL Port (Mini DIN 8 Pin) ( page 58) Use this port to connect a PC or control system. This enables you to control the projector using serial com­munication protocol. If you are writing your own pro­gram, typical PC control codes are on page
6
58.
Part Names of the Remote Control
1. Introduction
1
1. Infrared Transmitter ( page 8)
3
4
7
9
11
13 14
18
OFF
FOCUS PAGE
PIC-MUTE
MENU
ENTER
L-CLICK
VIDEO
S-VIDEO
VOLUME
ON
POWER
UP
DOWN
EXIT
R-CLICK
MOUSE
AUTO ADJ.COMPUTER
LAMP MODE
ASPECT HELP
FREEZEPICTURE
12. R-CLICK MOUSE Button* ( page 31)
2
6
5
8
10
12 15 17 16 19
21
22 20
2. POWER ON Button ( page 17)
3. POWER OFF Button ( page 27)
4. FOCUS (+) (–) Button ( page 24)
5. PIC-MUTE Button ( page 28)
6. PAGE (UP) / (DOWN) Button* ( page 31)
7. MENU Button
8. SELECT Buttons
9. ENTER Button
10. EXIT Button
11. L-CLICK MOUSE Button* ( page 31)
* Available only when the optional remote mouse receiver is connected with your computer.
13. VIDEO Button ( page 19)
14. S-VIDEO Button ( page 19)
15. COMPUTER Button ( page 19)
16. LAMP MODE Button ( page 28)
17. AUTO ADJ. Button ( page 26)
18. VOLUME (+) (–) Button ( page 26)
19. ASPECT Button ( page 38)
20. PICTURE Button ( page 37, 38)
21. HELP Button ( page 44)
22. FREEZE Button ( page 28)
7

Battery Installation

1. Introduction
1
Press firmly and slide the battery cover off.
2
Install new batteries (AAA). En­sure that you have the batteries' polarity (+/–) aligned correctly.
3
Slip the cover back over the bat­teries until it snaps into place. Do not mix different types of batter­ies or new and old batteries.

Remote Control Precautions

• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
• Do not heat, take apart, or throw batteries into fire.
• If you will not be using the remote control for a long time, remove the batteries.
• Ensure that you have the batteries' polarity (+/–) aligned correctly.
• Do not use new and old batteries together, or use different types of batteries together.
• Dispose of used batteries according to your local regulations.

Operating Range for Wireless Remote Control

30˚
30˚
Remote control
7m/22 feet
• The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet.
• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
Remote sensor on projector cabinet
8

2. Installation and Connections

This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
Set up a screen and the projector.
Connect your computer or video equip-
ment to the projector. See pages 12 to
15.
Connect the supplied power cable. See
page 16.
NOTE: Ensure that the power cable and any other cables are disconnected before moving the pro­jector. When moving the projector or when it is not in use, cover the lens with the lens cap.
To the wall outlet.
Setting Up the Screen and the Projector

Selecting a Location

The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 30" (0.76 m) measured diagonally when the projector is roughly 47 inches (1.2 m) from the wall or screen. The largest the image can be is 300" (7.6 m) when the projector is about 480 inches (12.2 m) from the wall or screen. Use the chart below as a rough guide.
609.6(W)457.2(H) / 240(W)180(H)
Screen Size (Unit: cm/inch)
300"
Screen Size (diagonal: inch)
487.7(W)365.8(H) / 192(W)144(H)
240"
406.4(W)304.8(H) / 160(W)120(H)
365.8(W)274.3(H) / 144(W)108(H)
304.8(W)228.6(H) / 120(W)90(H)
243.8(W)182.9(H) / 96(W)72(H)
203.2(W)152.4(H) / 80(W)60(H)
162.6(W)121.9(H) / 64(W)48(H)
121.9(W)91.4(H) / 48(W)36(H)
81.3(W)61.0(H) / 32(W)24(H)
61.0(W)45.7(H) / 24(W)18(H)
Lens center
30"
40"
1.2/47.2
1.6/63.0
60"
100"
80"
2.4/94.5
120"
3.2/126.0
150"
4.0/157.5
180"
200"
4.9/192.9
6.1/240.2
8.1/318.9
7.3/287.4
Distance (Unit: m/inch)
12.2/480.3
9.8/385.8
NOTE:
• The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.
• The Zoom lever adjusts the image size up to +/-10%
• For more details on throw distance, see next page.
• Changing the image size starts the Auto Focus to adjust the focus; changing the throw angle starts the Auto Keystone to correct
the vertical keystone distortion.
9
2. Installation and Connections

Throw Distance and Screen Size

The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
Distance Chart
C
Screen center
Lens center
α
2.4"/60 mm
Projector bottom
B = Vertical distance between lens center and screen center C = Throw distance α = Throw angle
NOTE: Distances may vary +/-5%.
Screen Size B C
inch
inch
120 144 160 176 192 208 224 240
inch
24
18
32
24
48
36
54
40
58
43
64
48
67
50
72
54
80
60
96
72
90 108 120 132 144 156 168 180
100 120 150 180 200 220 240 260 280 300
30 40 60 67 72 80 84 90
inch
12 18 20 22 24 25 27 30 36 45 54 60 66 72 78 84 90
9
Wide – TeleDiagonal Width Height
inch 42 – 51 57 – 69 86 – 104 96 – 116
104 – 125 115 – 139 121 – 146 130 – 156 145 – 174 174 – 209 218 – 261 262 – 314 291 – 349 320 – 384 350 – 419 379 – 454 408 – 489 438 – 524
α
Wide – Tele
degree
12.1 - 10.0
11.9 - 9.9
11.8 - 9.9
11.8 - 9.9
11.7 - 9.8
11.8 - 9.8
11.7 - 9.8
11.7 - 9.8
11.7 - 9.8
11.7 - 9.8
11.7 - 9.8
11.7 - 9.8
11.6 - 9.7
11.6 - 9.7
11.6 - 9.7
11.6 - 9.7
11.6 - 9.7
11.6 - 9.7
Screen bottom
Screen Size B C
mm
mm
610
813 1219 1361 1463 1626 1707 1829 2032 2438 3048 3658 4064 4470 4877 5283 5690 6096
mm
457 610
914 1021 1097 1219 1280 1372 1524 1829 2286 2743 3048 3353 3658 3962 4267 4572
762 1016 1524 1702 1829 2032 2134 2286 2540 3048 3810 4572 5080 5588 6096 6604 7112 7620
B
mm
229 305 457 511 549 610 640 686 762
914 1143 1372 1524 1676 1829 1981 2134 2286
Wide – TeleDiagonal Width Height
mm 1070 - 1290 1450 - 1740 2190 - 2630 2450 - 2940 2640 - 3170 2930 - 3520 3080 - 3700 3310 - 3970 3680 - 4410 4420 - 5300 5540 - 6640 6650 - 7980 7400 - 8870 8140 - 9760 8890 - 10650 9630 - 11540
10370 - 12430 11120 - 13320
α
Wide – Tele
degree
12.1 - 10.0
11.9 - 9.9
11.8 - 9.9
11.8 - 9.9
11.7 - 9.8
11.8 - 9.8
11.7 - 9.8
11.7 - 9.8
11.7 - 9.8
11.7 - 9.8
11.7 - 9.8
11.7 - 9.8
11.6 - 9.7
11.6 - 9.7
11.6 - 9.7
11.6 - 9.7
11.6 - 9.7
11.6 - 9.7
10
2. Installation and Connections
WARNING
* Installing your projector on the ceiling must be done
by a qualified technician. Contact your dealer for more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged.
• Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 41˚F (5˚C) and 104˚F (40˚C). (Eco mode selected automatically at 95°F to 104°F/35°C to 40°C)
• Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.
• Ensure that you have adequate ventilation around your projector so heat can dissipate. Do not cover the vents on the side or the front of the projector.
Reflecting the Image
Using a mirror to reflect your projector's image enables you to enjoy a much larger image when a smaller space
is required. Contact your dealer if you need a mirror
system. If you're using a mirror system and your im­age is inverted, use the MENU and SELECT buttons on your projector cabinet or your remote control to correct the orientation. ( page 41)
11
2. Installation and Connections
Making Connections

Connecting Your PC or Macintosh Computer

NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC. In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up. * If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power manage-
ment software.
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector. When using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections.
COMPUTER IN
VGA signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially available distribution amplifier if connecting a signal cable longer than the supplied one.
IBM VGA or Compatibles (Notebook type) or Macintosh (Notebook type)
COMPUTER IN
AUDIO IN
PC CONTROLAUDIO INS-VIDEO INVIDEO IN
Audio cable (not supplied)
NOTE: The L-shaped plug of an audio cable does not fit into the AUDIO IN jack.
PHONE
NOTE: For older Macintosh, use a commercially avail­able pin adapter (not supplied) to connect to your Mac's video port.
NOTE: The projector is not compatible with video decoded outputs of either the NEC ISS-6020 and ISS-6010 switchers.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan converter. This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following. * When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the projector cabinet.
12

To connect SCART output (RGB)

2. Installation and Connections
Projector
Video equipment such as DVD player
Commercially available SCART cable
Female
COMPUTER IN
COMPUTER IN
PC CONTROLAUDIO INS-VIDEO INVIDEO IN
ADP-SC1
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re­quired for this connection.
From the menu, select [Setup - Options] [Signal Select] [Computer] [Scart]. SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro­connector.
NOTE: Audio signal is not available for this connection.
TIP: The ADP-SC1 SCART adapter is obtainable from your dealer in Europe.
information.
13
Loading...
+ 49 hidden pages