Dukane 8755J, 8755J-RJ, 8919H, 8920H User Manual

Projector

8755J/8919H/8920H

User's Manual (detailed) Operating Guide

Thank you for purchasing this projector.

WARNING

product. Be sure to read “Safety Guide” rst. After reading them, store them in a safe place for future reference.

►Before using this product, please read all manuals for this

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING

CAUTION

NOTICE This entry notices of fear of causing trouble.

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

• Mac

• Windows® is a registered trademark of Microsoft Corporation in the U.S. and/or other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

All other trademarks are the properties of their respective owners.

• The information in this manual is subject to change without notice.

is a registered trademark of Apple Inc.

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



Contents



About this manual ...........1

Contents . . . . . . . . . . . . . . . . . . 2

Projector features ...........3

Preparations ...............3

Checking the contents of package

Part names . . . . . . . . . . . . . . . . 4

Projector . . . . . . . . . . . . . . . . . . . . . . 4

Control panel ................... 5

Rear panel . . . . . . . . . . . . . . . . . . . . 5

Remote control . . . . . . . . . . . . . . . . . 6

Setting up . . . . . . . . . . . . . . . . . 7

Arrangement ...................7

Connecting your devices .......... 9

Connecting power supply . . . . . . . . 11

Using the security bar and slot . . . . 11

Remote control ............12

Installing the batteries ...........12

About the remote control signal . . . 12 Changing the frequency of remote control signal Using as a simple PC mouse & keyboard

. . 13

Power on/off . . . . . . . . . . . . . . 14

Turning on the power . . . . . . . . . . . 14

Turning off the power . . . . . . . . . . . 14

Operating . . . . . . . . . . . . . . . . 15

Adjusting the volume ............ 15

Temporarily muting the sound .....15

Selecting an input signal .........15

Searching an input signal . . . . . . . . 17

Selecting an aspect ratio ......... 17

Adjusting the projector's elevator . . 18

Adjusting the zoom and focus .....18

Using the automatic adjustment feature

...19

Adjusting the position . . . . . . . . . . . 19

Correcting the keystone distortions

Using the magnify feature ........20

Temporary freezing the screen ....21

Temporarily blanking the screen . . 21

Using the menu function . . . . . . . . 22

EASY MENU. . . . . . . . . . . . . . . 24

As p e c t , Au t o k e y s t o n e ex e c u t e ,

e y s t o n e ,

k m

i r r o r , re s e t , Fi l t e r t i m e , lA n g u A g e ,

d v A n c e d m e n u , ex i t

pi c t u r e m o d e ,

ec o m o d e ,

PICTURE menu . . . . . . . . . . . . 26

IMAGE menu . . . . . . . . . . . . . . 29

...3

INPUT menu . . . . . . . . . . . . . . 31

SETUP menu ..............34

AUDIO menu . . . . . . . . . . . . . . 36

SCREEN menu .............37

OPTION menu . . . . . . . . . . . . . 42

SECURITY menu ...........47

Maintenance ..............53

. . 20

Troubleshooting . . . . . . . . . . . 58

Specications .............64



Br i g h t n e s s , co n t r A s t , gA m m A , c

o l o r t e m p , co l o r , ti n t , sh A r p n e s s ,

c t i v e i r i s, my m e m o r y

As p e c t , ov e r s c A n , v p o s i t i o n , h p o s i t i o n , h

p h A s e , h s i z e , Au t o A d j u s t e x e c u t e

pr o g r e s s i v e , vi d e o n r , co l o r s p A c e , c

o m p o n e n t , vi d e o F o r m A t , co m p u t e r i n,

r A m e l o c k , re s o l u t i o n

Au t o k e y s t o n e

c o m o d e , mi r r o r , st A n d B y m o d e ,

e m

o n i t o r o u t

e x e c u t e ,

ke y s t o n e ,

vo l u m e , sp e A k e r , Au d i o s o u r c e

lA n g u A g e , me n u p o s i t i o n , Bl A n k , s

t A r t u p ,

e s s A g e , so u r c e n A m e , te m p l A t e , c.c.

yScreen

, M

yScreen Lock

Au t o s e A r c h , Au t o k e y s t o n e , d

i r e c t o n , Au t o o F F , lA m p t i m e ,

i l t e r t i m e , my B u t t o n , my s o u r c e ,

e r v i c e

se c u r i t y p A s s w o r d c h A n g e ,

t m

p A s s w o r d , pi n l o c k ,

yScreen

r A n s i t i o n d e t e c t o r , my t e x t p A s s w o r d ,

y t e x t d i s p l A y , my t e x t w r i t i n g

Replacing the lamp .............53

Cleaning and replacing the air lter . . 55

Other care ....................57

Related messages . . . . . . . . . . . . . 58

Regarding the indicator lamps . . . . 59

Shutting the projector down . . . . . . 60

Resetting all settings ............60

Phenomena that may be easy

to be mistaken for machine defects

. . 61

Projector features / Preparations

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯ONOFF

㧗

FREEZE

Projector features

The projector provides you with the broad use by the following features.

ü This projector has a variety of I/O ports that supposedly cover for any

business scene.

ü This projector realizes the large projection image, even if in a small space. ü The new double layer lter system is expected to function longer and offers

you less maintenance frequency.

Preparations

Checking the contents of package

Your projector should come with the items shown below. Check that all the items are included. Require of your dealer immediately if any items are missing.

(1) Remote control with two AA batteries (2) Power cord (3) Computer cable (4) Lens cover (5) User’s manuals (Book x1, CD x1) (6) Security label

(1)

(2)

(3)

(4)

(5)

(6)

NOTE

• Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector. Use special caution for the lens.

Part names

Projector

(1) Lamp cover (53)

The lamp unit is inside. (2) Focus ring (18) (3) Zoom ring (18) (4) Control panel (5) (5) Elevator buttons (x 2) (18) (6) Elevator feet (x 2) (18) (7) Remote sensor (12) (8) Lens (57) (9) Intake vents (10) Filter cover (55)

The air lter and intake vent

are inside. (11) Speaker (36) (12) Exhaust vent (13) AC IN (AC inlet) (11) (14) Rear panel (5) (15) Security bar (11) (16) Security slot (11)

(6)

HOT!

(9)

(12)

(4)

(1)

(2) (3) (4)

(6)

(8)

(14)

(10)

(11)

(7)

(5)

(6)

(11)

(1)

(13)

WARNING

(15)

(16)

(14)

HOT!

(12)

►HOT! : Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Do not look into the lens or vents while the lamp is on, since the strong light is not good for your eyes. ►Do not handle the elevator buttons without holding the projector, since the projector may drop down.

CAUTION

►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air lter periodically. ►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

Control panel

Part names

(1) STANDBY/ON button (14) (2) INPUT button (15, 22) (3) MENU button (22)

It consists of four cursor buttons. (4) POWER indicator (11, 14, 59) (5) TEMP indicator (59) (6) LAMP indicator (59)

Rear panel (9)

(1) AUDIO IN1 port (2) AUDIO IN2 port (3) COMPUTER IN1 port (4) COMPUTER IN2 port (5) MONITOR OUT port (6) Shutdown switch (60) (7) CONTROL port

(11) (3)(5) (6) (1)

(1) (3)(2)

(8) USB port (13) (9) COMPONENT

(Y, Cb/Pb, Cr/Pr) ports (10) VIDEO port (11) S-VIDEO port (12) AUDIO IN3 (R, L) ports (13) AUDIO OUT (R, L) ports

(2)(4)

(6)(5)

(4)

(7)

CAUTION

(9)(10) (13)

(8)(12)

►Use the shutdown switch only when the projector is not turned off by normal procedure, since pushing this switch stops operation of the projector without cooling it down.

Part names

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Remote control

(1) VIDEO button (16) (2) COMPUTER button (16) (3) SEARCH button (17) (4) STANDBY/ON button (14) (5) ASPECT button (17) (6) AUTO button (19) (7) BLANK button (21) (8) MAGNIFY - ON button (20) (9) MAGNIFY - OFF button (13, 20) (10) MY SOURCE/DOC.CAMERA button (16, 44) (11) VOLUME - button (13, 15) (12) PAGE UP button (13) (13) PAGE DOWN button (13) (14) VOLUME + button (15) (15) MUTE button (15) (16) FREEZE button (21) (17) MY BUTTON - 1 button (44) (18) MY BUTTON - 2 button (44) (19) KEYSTONE button (20) (20) POSITION button (19, 20, 23) (21) MENU button (22) (22) ▲/▼/◄/► cursor buttons (13, 22) (23) ENTER button (

13, 22)

(24) ESC button (13, 22) (25) RESET button (

13, 22)

(26) Battery cover (12)

(2) (1) (6) (5) (16) (8) (9) (19) (17) (20) (22)

(24)

(10) (4) (3) (7) (12) (14) (11) (13) (15) (18) (21) (23) (25)

(26)

Back of

the remote control

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance.

The values shown in the table are calculated for a full size screen: 1024 x 768 a Screen size (diagonal) b Projection distance (±10%)

c1 , c2 Screen height (±10%)

On a horizontal surface

Screen size

(diagonal)

type

(inch)

30 0.8 0.9 34 1.0 41 41 16 5 2 1.0 38 1.1 45 39 15 -1 0 40 1.0 1.2 46 1.4 55 55 22 6 2 1.3 51 1.5 60 51 20 -2 -1 50 1.3 1.5 58 1.8 69 69 27 8 3 1.6 64 1.9 76 64 25 -2 -1 60 1.5 1.8 70 2.1 83 82 32 9 4 1.9 77 2.3 91 77 30 -2 -1 70 1.8 2.1 82 2.5 97 96 38 11 4 2.3 89 2.7 106 90 35 -3 -1 80 2.0 2.4 94 2.8 112 110 43 12 5 2.6 102 3.1 122 103 41 -3 -1

90 2.3 2.7 106 3.2 126 123 49 14 5 2.9 115 3.5 137 116 46 -4 -1 100 2.5 3.0 118 3.6 140 137 54 15 6 3.3 128 3.9 153 129 51 -4 -2 120 3.0 3.6 142 4.3 168 165 65 18 7 3.9 154 4.7 183 154 61 -5 -2 150 3.8 4.5 177 5.3 211 206 81 23 9 4.9 193 5.8 229 193 76 -6 -2 200 5.1 6.0 237 7.1 281 274 108 30 12 6.6 258 7.8 306 257 101 -8 -3 250 6.4 7.5 297 8.9 352 343 135 38 15 8.2 323 9.7 383 322 127 -10 -4 300 7.6 9.0 356 10.7 422 411 162 46 18 9.9 388 11.7 460 386 152 -12 -5

Projection distance

min. max. min. max.

m m inch m inch cm inch cm inch m inch m inch cm inch cm inch

4 : 3 screen 16 : 9 screen

c1 c2

Screen

height

Suspended from the ceiling

• Keep a space of 30 cm or more between the sides of the projector and other objects such as walls.

• For the case of installation in a special state such as ceiling mount, the specied mounting accessories (

64) and service may be required. Before installing the projector, consult your dealer about your installation.

Screen

height

Projection distance

Screen

height

Screen

height

Setting up

Arrangement (continued)

WARNING

►Place the projector in a stable horizontal position. If the projector falls or is knocked over, it could cause injury and/or damage to the projector. Using a damaged projector could then result in re and/or electric shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side, front or rear position.

• Consult with your dealer before a special installation such as suspending from

a ceiling or somewhere else. ►Place the projector in a cool place, and ensure that there is sufcient ventilation. The high temperature of the projector could cause re, burns and/or malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

• Do not place anything near the projector lens or vents, or on top of the

projector.

• Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the

bottom. ►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector. ►Use only the mounting accessories the manufacturer specied, and leave installing and removing the projector with the mounting accessories to the service personnel.

• Read and keep the user’s manual of the mounting accessories used.

CAUTION

►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector near humidiers, smoking spaces or a kitchen. ►Position the projector to prevent light from directly hitting the projector's remote sensor.

Setting up

Y CB/PB CR/PR

COMPONENT VIDEO OUT

L R

AUDIO OUT

VIDEO OUT

L R

AUDIO OUT

RGB OUT

AUDIO OUT

RGB OUT

RS-232C

RGB IN

L R

AUDIO OUT

S-VIDEO OUT

USB

L R

AUDIO IN

Connecting your devices

Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.

Monitor

Speakers

(with an

amplier)

VCR/DVD player

WARNING

►Do not disassemble or modify the projector and accessories.

►Be careful not to damage the cables, and do not use damaged cables.

CAUTION

►Turn off all devices and unplug their power cords prior to

connecting them to projector. Connecting a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction or damage to the device and the projector. ►Use appropriate accessory or designated cables. Ask your dealer about nonaccessory cables which may be required a specic length or a ferrite core by the regulations. For cables with a core only at one end, connect the end with the core to the projector. ►Make sure that devices are connected to the correct ports. An incorrect connection may result in malfunction or damage to the device and the projector.

NOTICE

input ports of the projector are recessed.

►Use the cables with straight plugs, not L-shaped ones, as the

Setting up

Connecting your devices (continued)

NOTE

• Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.

- Some signal may need an adapter to input this projector.

- Some PCs have multiple screen display modes that may include some signals

which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600X1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

• While connecting, make sure that the shape of the cable's connector ts the port to connect with. And be sure to tighten the screws on connectors with screws.

• When connecting a laptop PC to the projector, be sure to activate the PC’s external RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT display.) For details on how this is done, please refer to the instruction manual of the corresponding laptop PC.

• When the picture resolution is changed on a PC depending on an input, automatic adjustment function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.

• In some cases, this projector may not display a proper picture or display any picture on screen. For example, automatic adjustment may not function correctly with some input signals. An input signal of composite sync or sync on G may confuse this projector, so the projector may not display a proper picture.

About Plug-and-Play capability

Plug-and-Play is a system composed of a PC, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a PC that is VESA DDC (display data channel) compatible.

• Take advantage of this feature by connecting an RGB cable to the COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

• Please use the standard drivers in your PC as this projector is a Plug-andPlay monitor.

Connecting power supply

Put the connector of the power cord into the

AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

Please remember that when the DIRECT ON function activated (42), the connection of the power supply make the projector turn on.

Setting up

AC IN Power cord

WARNING

incorrect or faulty connections may result in re and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one.

• Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

• Never modify the power cord.

►Please use extra caution when connecting the power cord, as

Using the security bar and slot

Security slot

A commercial anti-theft chain or wire up to 10 mm in diameter can be attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool.

Anti-theft chain or wire

WARNING

from falling down, since it is not designed for it.

CAUTION

may become too hot.

►Do not use the security bar and slot to prevent the projector

►Do not place anti-theft chain or wire near the exhaust vents. It

Security bar

NOTE

measures. It is intended to be used as supplemental theft prevention measure.

• The security bar and slot is not comprehensive theft prevention

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery

cover, remove it. Align and insert the two AA batteries

(HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control. Replace the battery cover in the direction of the arrow and snap it back into place.

21 3

WARNING

directed. Improper use may result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

►Always handle the batteries with care and use them only as

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

•

NOTE

If it is difcult to send the signal to the sensor directly, attempt to make the signal reect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter uorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

The remote control signal reected in the screen or the like may be available.

Approx.

3 m

30º

Remote control

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency. In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds.

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons

(2)

(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons Please remember that the REMOTE FREQ. in the SERVICE item of

the OPTION menu

(46)

of the projector to be controlled should be

set to the same mode as the remote control.

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse and keyboard of the PC, when the projector's USB port (B type) connects with the PC's USB port (A type) port via a mouse cable.

(1) PAGE UP key: Press PAGE UP button. (2) PAGE DOWN key: Press PAGE DOWN button. (3) Mouse left button: Press ENTER button. (4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►. (5) ESC key: Press ESC button. (6) Mouse right button: Press RESET button.

USB port

(1)

(2)

WARNING

keyboard function could damage your equipment. While

►Improper use of the simple mouse &

(3)

using this function, please connect this product only to a PC. Be sure to check your PC’s manuals before

(5)

connecting this product to the PC.

NOTE

• When the simple mouse & keyboard function of this product does not

work correctly, please check the following.

- When a USB cable connects this projector with a PC having a built-in pointing device (e.g. track ball) like a notebook PC, open BIOS setup menu, then select the external mouse and disable the built-in pointing device, because the built-in pointing device may have priority to this function.

- Windows 95 OSR 2.1 or higher is required for this function. And also this function may not work depending on the PC’s congurations and mouse drivers. This function can work with the PC which can operate general USB mouse or keyboard.

- You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

- This function is activated only when the projector is working properly. This function is not available while the lamp is warming up (the POWER indicator blinks green), and while adjusting the volume and display, correcting for keystone, zooming in on the screen, using the BLANK function, or displaying the menu screen.

(4)

(6)

Power on/off

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯ONOFF

㧗

FREEZE

Power on/off

Turning on the power

Make sure that the power cord is rmly and

correctly connected to the projector and the

STANDBY/ON button POWER indicator

outlet. Make sure that the POWER indicator is

steady orange (59). Then remove the lens cover.

Press STANDBY/ON button on the

projector or the remote control. The projection lamp will light up and POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green (59).

To display the picture, select an input signal according to the section “Selecting an input signal” (15).

Turning off the power

Press the STANDBY/ON button on the projector or the remote control. The

message “Power off?” will appear on the screen for about 5 seconds. Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (59).

Attach the lens cover, after the POWER indicator turns in steady orange.

Do not turn the projector on for about 10 minutes or more after turning it off. Turning the projector on again too soon could shorten the lifetime of some consumable parts of the projector.

WARNING

►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE

• Turn the power on/off in right order. Please power on the projector

prior to the connected devices.

•

This projector has the function that can make the projector automatically turn on/ off. Please refer to the DIRECT ON OPTION menu.

• Use the shutdown switch (60) only when the projector is not turned off by normal procedure.

(42)

and AUTO OFF

(43)

items of the

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Operating

Adjusting the volume

Use the VOLUME +/VOLUME - buttons to adjust the volume.

A dialog will appear on the screen to aid you in adjusting the

VOLUME +/- button

volume. If you do not do anything, the dialog will automatically disappear after a few seconds.

● When

is selected for current picture input port, the volume adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (36).

● When the projector is in the standby mode, the volume can be adjusted if is not selected for the AUDIO OUT STANDBY and NORMAL is selected to the STANDBY MODE in the SETUP menu (35).

Temporarily muting the sound

Press MUTE button on the remote control.

A dialog will appear on the screen indicating that you have

MUTE button

muted the sound. To restore the sound, press the MUTE, VOLUME + or VOLUME - button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● When is selected for current picture input port, the sound is always muted. Please see AUDIO SOURCE item of AUDIO menu (36).

● C.C. (Closed Caption) is automatically activated when sound is muted and an input signal containing C.C is received. This function is available only when the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPONENT, COMPUTER IN1 or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (41).

Selecting an input signal

Press INPUT button on the projector.

Each time you press the button, the projector switches its input port from the current port as below.

COMPUTER IN 1  COMPUTER IN 2

VIDEO  S-VIDEO 

● While ON is selected for AUTO SEARCH item in OPTION menu (42), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

(continued on next page)

INPUT button

COMPONENT (Y, Cb/Pb, Cr/Pr)

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Selecting an input signal (continued)

Press COMPUTER button on the remote control.

Each time you press the button, the projector switches its input port from the current port as below.

COMPUTER IN 1  COMPUTER IN 2

● While ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (42). If COMPUTER button is pressed when VIDEO, S-VIDEO or COMPONENT port is selected, the projector will check COMPUTER IN1 port rst.

Press VIDEO button on the remote control.

Each time you press the button, the projector switches its input port from the current port as below.

COMPONENT (Y, Cb/Pb, Cr/Pr)  S-VIDEO  VIDEO

●

While ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (42). If VIDEO button is pressed when COMPUTER IN1 or COMPUTER IN2 port is selected, the projector will check COMPONENT port rst.

Press the MY SOURCE / DOC. CAMERA button on

the remote control. The input signal will be changed into the signal you set as MY SOURCE (44).

COMPUTER button

VIDEO button

MY SOURCE / DOC. CAMERA button

● This function also can use for document camera. Select the input port that connected the document camera.

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Operating

Searching an input signal

Press SEARCH button on the remote control.

The projector will start to check its input ports as below in

SEARCH button

order to nd any input signals. When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER IN 1  COMPUTER IN 2

VIDEO  S-VIDEO 

COMPONENT (Y, Cb/Pb, Cr/Pr)

● While ON is selected for AUTO SEARCH item in OPTION menu (42), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

Selecting an aspect ratio

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

 For a computer signal

NORMAL  4:3  16:9  16:10

 For a video signal, s-video signal or component video

signal

4:3  16:9  14:9

 For no signal

4:3 (xed)

ASPECT button

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

Operating

14°

Adjusting the projector's elevator

When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 14 degrees. This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable while pushing the elevator button on the same side as it.

Holding the projector, push the elevator buttons to loose the elevator feet.

Position the front side of the projector to the desired height.

Release the elevator buttons in order to lock the elevator feet.

After making sure that the elevator feet are locked, put the projector down

gently. If necessary, the elevator feet can be manually twisted to make more precise

adjustments. Hold the projector when twisting the feet.

To loose an elevator foot, push the

elevator button on the same side as it.

CAUTION

projector, since the projector may drop down. ►Do not tilt the projector other than elevating its front within 14 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself.

►Do not handle the elevator buttons without holding the

Adjusting the zoom and focus

Use the zoom ring to adjust the screen size.

Use the focus ring to focus the picture.

To nely adjust, twist the foot.

Zoom ring Focus ring

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Using the automatic adjustment feature

Press AUTO button on the remote control.

Pressing this button performs the following.

 For a computer signal

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

 For a video signal and s-video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT menu (

32). The vertical position and

horizontal position will be automatically set to the default.

 For a component video signal

The vertical position, horizontal position and horizontal phase will be automatically set to the default.

● The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

● When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

● When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model. The items adjusted by this function may vary when the FINE or DISABLE is selected

● for the AUTO ADJUST item of the SERVICE item in the OPTION menu (

AUTO button

45).

Adjusting the position

Press POSITION button on the remote control when no menu is

indicated. The “POSITION” indication will appear on the screen.

Use the ▲/▼/◄/► cursor buttons to adjust the picture position.

When you want to reset the operation, press RESET button on the remote control during the operation. To complete this operation, press POSITION button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

When this function is performed on a video signal, s-video signal or component

● video signal, some image such as an extra-line may appear at outside of the picture.

● When this function is performed on a video signal, s-video signal or component video signal, the range of this adjustment depends on OVER SCAN in IMAGE menu (

● If POSITION button is pressed when a menu is indicated on screen, the displayed picture does not move its position but the menu does.

29) setting. It is not possible to adjust when OVER SCAN is set to 10.

POSITION button

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE UP

VOLUME

DOWN

࡯

OFF

㧗

FREEZE

Correcting the keystone distortions

Press KEYSTONE button on the remote

control. A dialog will appear on the screen to

KEYSTONE button

aid you in correcting the distortion. Use the ▲/▼ cursor buttons to select AUTO or MANUAL

operation, and press the ► button to perform the following. (1) AUTO executes automatic vertical keystone correction.

(2) MANUAL displays a dialog for keystone correction.

Use the ◄/► buttons for adjustment.

To close the dialog and complete this operation, press KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● The adjustable range of this function will vary among inputs. For some input, this function may not work well.

● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, automatic vertical keystone correction may not work correctly.

● When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

● When the projector is placed on the level (about ±3°), the automatic keystone distortion correction may not work.

● When the projector is inclined to near ±30 degree or over, this function may not work well.

● This function will be unavailable when Transition Detector is on (

50).

Using the magnify feature

Press the ON button of MAGNIFY on the remote control.

The “MAGNIFY” indication will appear on the screen and the projector will go into the MAGNIFY mode. When the ON button of MAGNIFY is pressed rst after the projector is started, the picture will be zoomed twice. The indication will disappear in several seconds with no operation.

Use the ▲/▼ cursor buttons to adjust the zoom level.

To move the zoom area, press the POSITION button in the MAGNIFY mode, then use the ▲/▼/◄/► cursor buttons to move the area. And to nalize the zoom area, press the POSITION button again. To exit from the MAGNIFY mode and restore the screen to normal, press the OFF button of MAGNIFY on the remote control.

● The projector automatically exits from the MAGNIFY mode when the input signal is changed or when the display condition is changed.

● In the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exits from the MAGNIFY mode.

NOTE

nd the level you want.

• The zoom level can be nely adjusted. Closely watch the screen to

MAGNIFY ON/OFF button

+ 45 hidden pages