Dukane 8755C, 8063 User Manual

Download

Page 1

LCD Projector

Model 8063/8755C

User's Manual

Operators Guide

Page 2

Contents:

1. User's Manual– Safety Guide, ..................Page 1-9

2. User's Manual– Operating Guide, .............Page 1-49

3. User's Manual– Technical Guide, ..............Page 1-14

Page 3

Projector

User's Manual - Safety Guide

Thank you for purchasing this projector.

WARNING • Before using, read these user's manuals of this projector to ensure

correct usage through understanding. After reading, store them in a safe place for future reference. Incorrect handling of this product could possibly result in personal injury or physical damage. The manufacturer assumes no responsibility for any damage caused by mishandling that is beyond normal usage defined in these manuals of this projector.

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in this manual

• The reproduction, transmission or use of this document or contents is not permitted without express written authority.

• The information in this manual is subject to change without notice.

About The Symbols

Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the contents.

This symbol indicates information that, if ignored, could

WARNING

CAUTION

Typical Symbols

This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.

possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to incorrect handling.

This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left indicates that the power plug should be disconnected from the power outlet).

Page 4

Safety Precautions

WARNING

Never use the projector if a problem should occur.

Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.

• The power outlet should be close to the projector and easily accessible.

Use special caution for children and pets.

Incorrect handling could result in fire, electrical shock, injury, burn or vision problem. Use special caution in households where children and pets are present.

Do not insert liquids or foreign object.

Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are present. If liquids or foreign object should enter the projector, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

• Do not place the projector in a bathroom.

• Do not expose the projector to rain or moisture.

• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the projector.

• Do not place metals, combustibles, etc on or around the projector.

• To avoid penetration of foreign objects, do not put the projector into a case or bag together with any thing except the accessories of the projector, signal cables and connectors.

Never disassemble and modify.

The projector contains high voltage components. Modification and/or disassembly of the projector or accessories could result in fire or electrical shock.

• Never open the cabinet.

• Ask your dealer to repair and clean insider.

Do not give the projector any shock or impact.

If the projector should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock. If the projector is shocked, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

Do not place the projector on an unstable surface.

If the projector should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.

• Do not place the projector on an unstable, slant or vibrant surface such as

a wobbly or inclined stand.

• Use the caster brakes placing the projector on a stand with casters.

• Do not place the projector in the side up position, the lens up position or

the lens down position.

• In the case of a ceiling installation or the like, contact your dealer before

installation. 2

Disconnect the

plug from the power outlet.

Do not

disassemble.

Page 5

Safety Precautions (continued)

WARNING

Be cautious of High temperatures of the projector.

High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn. Take care of ventilation.

• Keep a space of 30 cm or more between the sides and other objects such

as walls.

• Do not place the projector on a metallic table or anything weak in heat.

• Do not place anything about the lens, air fans and ventilation openings of

the projector.

• Do not use with the ventilation opening facing downwards.

• Never block the air fan and ventilation openings.

• Do not cover the projector with a tablecloth, etc.

• Do not place the projector on a carpet or bedding.

Never look through the lens or openings when the lamp is on.

The powerful light could adversely affect vision. Use special caution in households where children are present.

Use only the correct power cord and the correct power outlet.

Incorrect power supply could result in fire or electrical shock.

• Use only the correct power outlet depending on the indication on the

projector and the safety standard.

• The enclosed power cord must be used depending on the power outlet to

be used.

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.

• Do not touch the power cord with a wet hand.

• Check that the connecting portion of the power cord is clean (with no

dust), before using. Use a soft and dry cloth to clean the power plug.

• Insert the power plug into a power outlet firmly. Avoid using a loose,

unsound outlet or contact failure.

Be sure to connect with ground wire.

Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the building using the correct power cord; otherwise, fire or electric shock can result.

• Don’t take the core of power cord away.

Surely connect

the ground wire.

Page 6

Safety Precautions (continued)

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”. Be careful in handling the power cord and external connection cables.

If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables. If the power cord or cables is damaged (exposed or broken core wires, etc.), contact your dealer.

• Do not place the projector or heavy objects on the power cord and cables.

Also, do not place a spread, cover, etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

• Do not pull the power cord and cables. When connecting and

disconnecting the power cord or cables, do it with your hand holding the plug or connector.

• Do not place the cord near the heater.

• Avoid bending the power cord sharply.

• Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

• Keep the battery away from children and pets. If swallowed consult a

physician immediately for emergency treatment.

• Do not allow the battery in a fire or water.

• Avoid fire or high-temperature environment.

• Do not hold the battery with the metallic tweezers.

• Keep the battery in a dark, cool and dry play.

• Do not short circuit the battery.

• Do not recharge, disassemble or solder the battery.

• Do not give the battery a physical impact.

• Use only the battery specified in the other manual of this projector.

• Make sure the plus and minus terminals are correctly aligned when

loading the battery.

• If you observe a leakage of the battery, wipe out the flower and then

replace the battery. If the flower adheres your body or clothes, rinse well with water.

• Obey the local laws on disposing the battery.

Page 7

Safety Precautions (continued)

CAUTION

Be careful in moving the projector.

Neglect could result in an injury or damage.

• Do not move the projector during use. Before moving, disconnect the

power cord and all external connections, and close the slide lens door or attach the lens cap.

• Avoid any impact or shock to the projector.

• Do not drag the projector.

• For moving the projector, use the enclosed case or bag if provided.

Do not put anything on top of the projector.

Placing anything on the projector could result in loss of balance or falling, and cause an injury or damage. Use special caution in households where children are present.

Do not attach anything other than specified things to the projector.

Neglect could result in an injury or damage.

• Some projector has a screw thread in a lens part. Do not attach anything

other than specified options (such as conversion lens) to the screw thread.

Avoid a smoky, humid or dusty place.

Placing the projector in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.

• Do not place near the smoking space, the kitchen or a humidifier.

Take care of the air filter to normal ventilate.

The air filter should be cleaned periodically. If the air filter becomes clogged by dust or the like, internal temperature rises and could cause malfunction. The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

• When the indicators or a message prompts you to clean the air filter, clean

the air filter as soon as possible.

• If the soiling will not come off the air filter, or it becomes damaged,

replace the air filter.

• Use the air filter of the specified type only. Please order the air filter

specified in the other manual of this projector to your dealer.

• When you replace the lamp, replace also the air filter. The air filter may be

attached when you buy a replacement lamp for this projector.

• Do not turn on the projector without air filter.

Avoid a high temperature environment.

The heat could have adverse influence on the cabinet of the projector and other parts. Do not place the projector, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.

Remove the power cord for complete separation.

• For safety purposes, disconnect the power cord if the projector is not to be

used for prolonged periods of time.

• Before cleaning, turn off and unplug the projector. Neglect could result in

fire or electrical shock.

Disconnect the

plug from the

power outlet.

Page 8

Safety Precautions (continued)

CAUTION

Ask your dealer to cleaning inside of the projector about every two years.

Accumulations of dust inside the projector cause result in fire or malfunction. Cleaning inside is more effective if performed before every humid periods such as rainy season.

• Do not clean inside yourself because it is dangerous.

NOTE

Do not give the remote control any physical impact.

A physical impact could cause damage or malfunction of the remote control.

• Take care not to drop the remote control.

• Do not place the projector or heavy objects on the remote control.

Take care of the lens.

• Close the slide lens door or attach the lens cap to prevent the lens surface being

scratched when the projector is not used.

• Do not touch the lens to prevent fog or dirt of the lens that cause deterioration of display

quality.

• Use commercially available lens tissue to clean the lens (used to clean cameras,

eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Take care of the cabinet and the remote control.

Incorrect care could have adverse influence such as discoloration, peeling paint, etc.

• Use a soft cloth to clean the cabinet and control panel of the projector and the remote

control. When excessively soiled dilute a neutral detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth. Do not use undiluted detergent directly.

• Do not use an aerosol sprays, solvents, volatile substances or abrasive cleaner.

• Before using chemical wipes, be sure to read and observe the instructions.

• Do not allow long-term close contact with rubber or vinyl.

About bright spots or dark spots.

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

Be careful of printing of the LCD panel.

If the projector continues projecting a still image, inactive images or 16:9 aspect images in case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed. In such a case, please make the projector project a whole white screen for 1 hour or more. You can use the BLANK function of the projector.

About consumables.

Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time, even if one year has not passed since the beginning of using. For more details, please consult your dealer.

Page 9

Safety Precautions (continued)

NOTE

Avoid strong rays.

Any strong ray (such as direct rays of the sun or room lighting) onto the remote control sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause disordered image or noises.

• Avoid radio generator such as a mobile telephone, transceiver, etc. around the projector.

About displaying characteristic.

The display condition of the projector (such as color, contrast, etc.) depends on characteristic of the screen, because the projector uses a liquid crystal display panel. The display condition can differ from the display of CRT.

• Do not use a polarized screen. It can cause red image.

Turn the power on/off in right order.

To prevent any trouble, turn on/off the projector in right order mentioned below unless specifying.

• Power on the projector before the computer or video tape recorder.

• Power off the projector after the computer or video tape recorder.

Take care not to fatigue your eyes.

Rest the eyes periodically.

Set the sound volume at a suitable level to avoid bothering other people.

• It is better to keep the volume level low and close the windows at night to protect the

neighborhood environment.

Connecting with notebook computer

When connecting with notebook computer, set to valid the RGB external image output (setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of the notebook for more information.

Page 10

Lamp

WARNING

The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in USA) For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect the

plug from the

power outlet

• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

• Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

• Use the lamp of the specified type only.

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• If the indicators or a message prompts you to replace the lamp (see the section “Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

Page 11

Regulatory Notices

FCC Statement Warning WARNING: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that the following conditions are met. Some cables have to be used with the core set. Use the accessory cable or a designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of WARNING in this manual), when a problem occurs with the equipment, first refer to the “Troubleshooting” section of the “User’s manual – Operating Guide”, and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.

Page 12

Page 13

Projector

8063/8755C

User's Manual – Operating Guide

Thank you for purchasing this projector.

WARNING ►Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING This symbol indicates information that , if ignored, could possibly

result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that , if ignored, could result

possibly in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



ENGLISH

NOTE • The information in this manual is subject to chance without notice.

• The manufacture assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transmission or use of this document or contents is not permitted without

express written authority.

Trademark acknowledgment

• VGA and XGA are registered trademarks of the International Business Machines Corporation.

• Apple and Mac are registered trademarks of the Apple Computer, Inc.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

• Windows is a registered trademark of the Microsoft Corporation.

• Internet Explorer is a trademark of the Microsoft Corporation.

All other trademarks are the property of their respective owners.

Page 14

Contents

 

About this manual . . . . . . . . . . 1

Contents . . . . . . . . . . . . . . . . . 2

Projector feature Preparation Part name

s . . . . . . . . . . . . . . . 4

Projector . . . . . . . . . . . . . . . . . . . . . 4

Controls . . . . . . . . . . . . . . . . . . . . . . 5

Remote control . . . . . . . . . . . . . . . . 5

Setting up . . . . . . . . . . . . . . . . 6

Arrangement . . . . . . . . . . . . . . . . . . 7

Adjusting the projector's elevator . . 8 About the ﬁlter cover for bottom-up use

Connecting your devices . . . . . . . . 10

Connecting power supply . . . . . . . 13

Remote contro

Putting batteries . . . . . . . . . . . . . . 14

Using the remote control . . . . . . . . 15

Power on/of

Turning on the powe

Turning off the power . . . . . . . . . . . 16

Operating . . . . . . . . . . . . . . . 17

Adjusting the volume . . . . . . . . . . . 17

Temporarily muting the soun

Selecting an input signal . . . . . . . . 17

Searching an input signal . . . . . . . 18

Selecting the aspect ratio . . . . . . . 18

Adjusting the zoom and focus . . . . 18

Using the automatic adjustment feature

Adjusting the position . . . . . . . . . . 19

Correcting the keystone distortions 19

Using the magnify feature . . . . . . . 20

Freezing the screen . . . . . . . . . . . . 20

Temporarily blanking the scree Operating the computer screen . . . 21

Multifunctional settings . . . . 22

Using the menu function . . . . . . . . 22

EASY Menu . . . . . . . . . . . . . . . . . . 23

Aspect, Keystone, Mode, Bright, Contrast, Color, Tint, Sharpness, Whisper, Mirror, Reset, Filter time, Language, Go to advanced menu

s . . . . . . . . . . 3

s . . . . . . . . . . . . . . 3

. . 9

l . . . . . . . . . . . 14

f . . . . . . . . . . . . . 16

r . . . . . . . . . . . 16

d . . . . 17

. 19

n . . 20

PICTURE Menu . . . . . . . . . . . . . . . 25

Bright, Contrast, Gamma, Color temp, Color, Tint, Sharpness, Progressive, My memory

IMAGE Menu . . . . . . . . . . . . . . . . . 28

Aspect, Over scan, V. position, H. position, H. phase, H. size, Auto adjust

INPUT Menu . . . . . . . . . . . . . . . . . 30

Color space, Component, Video format, Frame lock, Information

SETUP Menu . . . . . . . . . . . . . . . . . 32

Keystone, Whisper, Mirror, Volume

SCREEN Menu . . . . . . . . . . . . . . . 33

Language, Menu position, OSD bright, Blank, Start up, MyScreen, MyScreen lock, Message

OPTION Menu . . . . . . . . . . . . . . . . 36

Search, Auto off, Lamp time, Filter time, Service

Maintenance . . . . . . . . . . . . . 38

Lamp . . . . . . . . . . . . . . . . . . . . . . . 38

Air ﬁlte

r . . . . . . . . . . . . . . . . . . . . . 40

Other care . . . . . . . . . . . . . . . . . . . 41

Troubleshootin

g . . . . . . . . . . 42

Related messages . . . . . . . . . . . . . 42

Regarding the indicator lamps . . . . 44

Phenomena that may easily be

mistaken for machine defects . . . . 46

Warranty and after-service Speciﬁcation

s . . . . . . . . . . . . 48

. . . 48

Page 15

ENGLISH

Projector features / Preparations

Projector features

This projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. It requires just a little space for installation and gets a large image from short distance.

High Brightness



Newly developed 165W UHB (Ultra High Brightness) lamp gives you a higher brightness image on a screen. The image can be still kept as bright and clean enough for use in bright rooms.

Low Noise



WHISPER mode is equipped for reducing acoustic noise to realize quieter operation. It is perfect for use in low luminance rooms where low noise is more important than brightness.

Rich Connectivity



This projector has a variety of I/O ports. It can be easily connected to many signal sources like PC, DVD and so on. The rich connectivity provides you more options to make your presentation impressive.

Compact Body



Even with its many features, this projector is extremely compact and slim, which gives you more ﬂexibility and usability to use it where you want.

Preparations

About contents of package

Please see the "Contents of package" of the "User's manual - Quick guide". Your projector should come with the items shown there. Contact immediately your dealer if anything is missing.

NOTE

moving the projector, be sure to use the original packing material

caution for the lens part.

• Keep the original packing materials for future reshipment. For . Use special

Page 16

Part names

VIDEO

AUDIO IN1

RGB IN1

CONTRO

RGB IN2 RGB OU

AUDIO IN2

AUDIO OU

S-VIDE

COMPONENT VIDE

CB/PB

CR/PR

Part names

Projector

Zoom knob (18) Focus ring (18)

Remote sensor (15)

Speaker (6)

Vent (6)

Lens cover (16) (Slide door)

Lens (16)

Lamp cover (Lamp unit is inside.) (38)

Control buttons (See the following page.) (5)

Ports (See below.)

AUDIO OUT port (11) AUDIO IN1 port (11) S-VIDEO port (12)

COMPONENT VIDEO ports (12)

CB/P

CR/P VIDEO port (12) AUDIO IN2 port (11) USB port (11)

Front-Right side

Bottom side

Elevator button (8)

Elevator foot (8)

Filter cover (40) (Air ﬁlter and intake vent are inside.)

Power switch (16)

AC inlet (13)

Elevator button (8)

Elevator foot (8)

Vent (6)

Rear-Left side

Restart switch (*) (46) RGB IN1 port (11) RGB IN2 port (11) RGB OUT port (11)

CONTROL port (11) Kensington lock slot

Ports

NOTE (*) About Restart switch: This Projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar and before turning on again, make the projector cool down at least 10 minutes without

operating. Only push the Restart switch in these exceptional instances.

Page 17

ENGLISH

Control buttons

STAN DBY /O N INP UT

MEN U

POW ER

TE MP

LA MP

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

LAMP indicator (44) TEMP indicator (44) POWER indicator (16)

NDBY/ON button (16)

STA

Remote control

Part names

Cursor buttons ▲,▼,◄,► (22)

INPUT button

(17)

RGB button (17)

VIDEO button (17)

ASPECT button (18)

HOME button (21)

MAGNIFY (20)

ON button OFF button

END button (21)

FREEZE button (20)

POSITION button (19)

Cursor buttons ▲,▼,◄,►(22)

ESC button (22)

SEARCH button (18)

STANDBY/ON button

AUTO

button (19)

BLANK button (20)

VOLUME button (17)

PAGE UP button

MUTE button (17)

PAGE DOWN button

KEYSTONE button

MENU button (22)

ENTER button (22)

RESET button

(16)

(21)

(19)

(22)

Page 18

Setting up

WARNING ►Place the projector in a stable position horizontally. A fall or a turnover could cause an injury and/or damage to the projector. Then using damaged projector could result in a ﬁre and/or an electric shock.

• Don’t place the projector on an unstable, slant or vibrant surface such as a

wobbly or inclined stand.

• Do not place the projector in the side/front/rear-up position, except care of the

air ﬁlter.

• For the projector installed bottom-up, use the accessory ﬁlter cover for bottom-

up use. And in the case of a ceiling installation or the like, contact your dealer

before installation. ►Place the projection in a cool place, and pay attention enough to ventilation. The high temperature of the projector could cause a ﬁre, a burn and/or malfunction to the projector.

• Don’t stop up, block and cover the projector's vents.

• Keep a space of 30 cm or more between the sides and other objects such as

walls.

• Don’t place the projector on a metallic thing or anything weak in heat.

• Don’t place the projector on a carpet, cushion or bedding.

• Don’t place the projector in direct sunlight or near a hot object such as heater.

• Put nothing about lens and vents of the projector. Put nothing on the projector.

• Put nothing that is sucked or sticks to the bottom of projector. This projector

has some intake vents also on the bottom. ►Do not place the projector on the place that gets wet. Damping the projector or inserting liquid in the projector could cause a ﬁre, an electric shock and/or malfunction to the projector.

• Don’t place the projector in a bathroom or the outdoors.

• Put nothing containing the liquid near the projector.

CAUTION ►Avoid a smoky, humid or dusty place. Placing the projector in such place could cause a ﬁre, an electric shock and/or malfunction to the projector.

• Don’t place the projector near a humidiﬁer, a smoking space or a kitchen.

• Put nothing containing the liquid near the projector. ►Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.

Page 19

ENGLISH

Setting up

Arrangement

Refer to the illustrations and tables below to determine the screen size and projection distance.

The values shown in the table are calculated for a full size screen: 1280 x 720 (a) The screen size (diagonal) (b) Distance from the projector to the screen (±10%) (c) The height of the screen (±10%)

(b)

4:3

(a)

At 4:3 screen

(a) Screen size

[inch (m)]

30 (0.8) 0.9 (35) 1.1 (42) 40 (1.0) 1.2 (47) 1.4 (56) 6 (2) 55 (22) 50 (1.3) 1.5 (59) 1.8 (71) 8 (3) 69 (27) 60 (1.5) 1.8 (72) 2.2 (85) 9 (4) 82 (32) 70 (1.8) 2.1 (84) 2.5 (100) 11 (4) 96 (38) 80 (2.0) 2.4 (96) 2.9 (114) 12 (5) 110 (43)

90 (2.3) 2.7 (108) 3.3 (129) 14 (5) 123 (49) 100 (2.5) 3.1 (120) 3.6 (143) 15 (6) 137 (54) 120 (3.0) 3.7 (144) 4.4 (172) 18 (7) 165 (65) 150 (3.8) 4.6 (181) 5.5 (216) 23 (9) 206 (81) 200 (5.1) 6.1 (242) 7.3 (288) 30 (12) 274 (108) 250 (6.4) 7.6 (303) 9.2 (361) 38 (15) 343 (135) 300 (7.6) 9.2 (363) 11.0 (433) 46 (18) 411 (162)

At 16:9 screen

(a) Screen size

[inch (m)]

30 (0.8) 1.0 (38) 1.2 (46) 40 (1.0) 1.3 (52) 1.6 (62) -2 (-1) 51 (20) 50 (1.3) 1.6 (65) 2.0 (77) -2 (-1) 64 (25) 60 (1.5) 2.0 (78) 2.4 (93) -2 (-1) 77 (30) 70 (1.8) 2.3 (91) 2.8 (109) -3 (-1) 90 (35) 80 (2.0) 2.7 (105) 3.2 (125) -3 (-1) 103 (41)

90 (2.3) 3.0 (118) 3.6 (140) -4 (-1) 116 (46) 100 (2.5) 3.3 (131) 4.0 (156) -4 (-2) 129 (51) 120 (3.0) 4.0 (158) 4.8 (188) -5 (-2) 154 (61) 150 (3.8) 5.0 (197) 6.0 (235) -6 (-2) 193 (76) 200 (5.1) 6.7 (264) 8.0 (314) -8 (-3) 257 (101) 250 (6.4) 8.4 (330) 10.0 (393) -10 (-4) 322 (127) 300 (7.6) 10.1 (396) 12.0 (472) -12 (-5) 386 (152)

16:9

(a)

(b) Projection distance [m (inch)] (c) Screen height [cm (inch)]

min. max. down up

5 (2) 41 (16)

(b) Projection distance [m (inch)] (c) Screen height [cm (inch)]

min. max. down up

-1 (0) 39 (15)

Page 20

Setting up

Adjusting the projector's elevator

WARNING ►Do not adjust the projector’s elevator during use or

immediately after use. Handling while the projector is in a high temperature could cause a burn and/or malfunction to the projector.

CAUTION ►If you press the elevator button without holding the projector, the projector might crash down, overturn, smash your ﬁngers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to adjust the elevator feet. ►Except for inclining by the elevator feet adjustment, place the projector horizontally.

You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection. The adjustment range of the elevator feet is 0 to 9 degrees.

Elevator feet

After making sure that the projector is cool adequately, press and hold in the

elevator buttons while holding the projector.

The elevator buttons and the elevator feet are on the both sides.

Raise or lower the projector to the desired height and the release the elevator

buttons.

When you release the elevator buttons, the elevator feet will lock into position.

As necessary, you can also ﬁnely adjust the height of the projector by twisting

the elevator feet by hand.

Elevator button

Page 21

ENGLISH

Setting up

About the ﬁlter cover for bottom-up use

WARNING ►Do not replace the ﬁlter cover during use or immediately

after use. While the projector connects with a power supply, or the projector is in a high temperature state, handling could cause an electric shock, a ﬁre, a burn and/or malfunction to the projector.Before handling, make sure the power switch is off and the power cord is not plugged in, then wait at least 45 minutes.

When the projector is installed bottom up, please use the accessory ﬁlter cover for bottom-up use. It is higher than usual ﬁlter cover, to keep the space for intake ventilation. Please change in the following procedure.

Filter cover’s knob

To remove

Filter cover

After making sure that the projector is cool adequately, slowly turn the

projector so that the lens-side is facing up. Please be careful for a projector

not to fall. While the projector is placed lens-side up, hold the projector.

Putting a ﬁnger on the ﬁlter cover’s knob, slide the ﬁlter cover in the direction

of the arrow to remove it.

Replace the ﬁlter cover for bottom-up use and snap it back into place.

Slowly turn the projector so that the top is facing up.

Filter cover for bottom-up use

Filter cover’s knob

To set

Page 22

Setting up

Connecting your devices

CAUTION ►Turn off all devices prior to connecting them to the projector.

Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector. ►Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector. ►Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.

NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer instruction manual of the corresponding laptop computer.

• Secure the screws on the connectors and tighten.

• Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

• For some RGB signal modes, the optional Mac adapter is necessary.

• When the image resolution is changed on a computer, depending on an input, automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.

About Plug-and-Play capability

Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible.

• Please take advantage of this function by connecting the accessory RGB cable to the RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

• Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.

to the

Page 23

ENGLISH

VIDEO

AUDIO IN1

RGB IN1

CONTROL

RGB IN2 RGB OUT

AUDIO IN2

AUDIO OUT

USB

S-VIDEO

COMPONENT VIDEO

CB/P

CR/P

VIDEO

AUDIO IN1

RGB IN1

CONTRO

RGB IN2 RGB OU

AUDIO IN2

AUDIO OUT

USB

S-VIDEO

COMPONENT VIDEO

CB/P

CR/P

VIDEO

AUDIO IN1

RGB IN1

CONTROL

RGB IN2 RGB OUT

AUDIO IN2

AUDIO OUT

USB

S-VIDEO

COMPONENT VIDEO

CB/P

CR/P

VIDEO

AUDIO IN1

RGB IN1

CONTROL

RGB IN2 RGB OUT

AUDIO IN2

AUDIO OUT

USB

S-VIDEO

COMPONENT VIDEO

CB/P

CR/P

Examples of connection with a computer

RGB cable

Stereo mini

audio cable

Setting up

* AUDIO IN1

is linked to

RGB IN1.

RGB out

RS-232C

Audio out

USB(A)

USB

RS-232C

cable

RGB out Audio out

Stereo mini audio cable

Connecting to a monitor (output)

RGB in

RGB cable

Connecting to a speaker with ampliﬁer (output)

RGB cable

Audio in

Stereo mini

audio cable

Page 24

Setting up

VIDEO

AUDIO IN1

RGB IN1

CONTROL

RGB IN2 RGB OUT

AUDIO IN2

AUDIO OUT

USB

S-VIDEO

COMPONENT VIDEO

CB/P

CR/P

VIDEO

AUDIO IN1

RGB IN1

CONTROL

RGB IN2 RGB OUT

AUDIO IN2

AUDIO OUT

USB

S-VIDEO

COMPONENT VIDEO

CB/P

CR/P

VIDEO

AUDIO IN1

RGB IN1

CONTROL

RGB IN2 RGB OUT

AUDIO IN2

AUDIO OUT

USB

S-VIDEO

COMPONENT VIDEO

CB/P

CR/P

VIDEO

AUDIO IN1

RGB IN1

CONTROL

RGB IN2 RGB OUT

AUDIO IN2

AUDIO OUT

USB

S-VIDEO

COMPONENT VIDEO

CB/P

CR/P

Examples of connection with a VCR/DVD player

out

Audio out

Audio out S-Video out

Video

Video cable

Stereo mini audio cable

Audio out

S-Video cable

Component video out

CB/P

CR/P

Component video cable

Component video out

CB/P

CR/P

Component video cable

Stereo mini audio cable

Page 25

ENGLISH

Setting up

Connecting power supply

WARNING ►Please use extra caution when connecting the power cord as

incorrect or faulty connections may result in ﬁre and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.

• Only plug the power cord into an outlet rated for use with the power cord's speciﬁed voltage range.

• Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug.

AC inlet

Connector of the power cord

Connect the connector of the power cord to the

AC inlet of the projector. Firmly plug the power cord's plug into the outlet.

Page 26

Remote control

Putting batteries

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage, which could result in ﬁre, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries speciﬁed. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

• Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

• Do not allow a battery in a ﬁre or water. Keep batteries in a dark, cool and dry play.

• If you observe a leakage of a battery, wipe out the ﬂower and then replace a battery. If the ﬂower adheres your body or clothes, rinse well with water immediately.

Remove the battery cover.

Slide back and remove the battery cover in the direction of the arrow.

nsert the batteries.

Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control.

Close the battery cover.

Replace the battery cover in the direction of the arrow and snap it back into place.

Page 27

ENGLISH

Remote control

Using the remote control

CAUTION ►Be careful in handling the remote control.

• Do not drop or otherwise expose the remote control to physical impact.

• Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.

• Remove the batteries from the remote control and store them in a safe place if you won’t be using the remote control for an extended period.

• Replace the batteries whenever the remote control starts to malfunction.

• When strong lights, such as direct sunlight or light from an extremely close range (such as from an inverter ﬂuorescent lamp), hit the projector’s remote sensor, the remote control may cause to function. Adjust the direction of the projector to keep light from directly hitting the projector’s remote sensor.

The remote control works with the projector’s remote sensor.

approx. 3 meters

30º

• The range of the remote sensor is 3 meters with a 60- degree range (30 degrees to the left and right of the remote sensor).

• Also a remote signal reﬂected in the screen etc. may be available. If it is difﬁcult to send a remote signal to the sensor directly, please try.

• Since the remote control uses infrared light to send signals to the projector (Class1 LED), be sure to use the remote control in an area free from obstacles that could block the remote control’s output signal to the projector.

Page 28

Power on/off

STANDB Y/O N INPU T

POWE R

TEM P

LAM P

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

Power on/off

WARNING ►When the power is on, a strong light is emitted. Do not look

into the lens or vents of the projector.

NOTE • Turn the power on/off in right order. Please power on the projector

before the connected devices. Power off the projector after the connected devices.

POWER STANDBY/ON button

indicator

Power switch

Turning on the power

Make sure that the power cord is ﬁrmly and correctly

connected to the projector and outlet. Open the lens cover, and set the power switch to the

ON position. The power indicator will light to solid orange. Then wait several seconds because buttons may not function for these several seconds.

Press the STANDBY/ON button on the projector or remote control.

The projector lamp will light up and the POWER indicator will begin blinking green. When the power is completely on, the indicator will stop blinking light green.

To display the picture, select an input signal according to the section "Selecting an input signal"

(17)

Turning off the power

Press the STANDBY/ON button on the projector or

remote control. The message "Power off?" will appear on the screen for approximately 5 seconds.

Press the STANDBY/ON button on the projector or

remote control again while the message is visible. The projector lamp will go off, and the POWER indicator will begin blinking orange.

Then the POWER indicator will stop blinking and light to solid orange when the lamp cooling is complete.

Make sure that the power indicator lights to solid orange, set the power switch

to the OFF position. The POWER indicator will go off. Close the lens cover.

POWER

(Solid orange)

POWER

(Blinking green)

POWER

(Solid green)

Power off?

POWER

(Blinking orange)

POWER

(Solid orange)

Page 29

ENGLISH

Operating

VIDEO

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

MAGNIFY

ASPECT AUTO

BLANK

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

VIDEO

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

STANDBY /ON INPUT

POWER

TEMP

LAMP

VIDEO

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

ASPECT AUTO

BLANK

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

ASPECT AUTO

BLANK

Operating

Adjusting the volume

Press the VOLUME button on the remote control.

A dialog will appear on the screen to aid you in adjusting the volume.

Use the cursor buttons ▲/▼ to adjust the volume.

To close the dialog and complete the operation, press the VOLUME button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

Temporarily muting the sound

Press the MUTE button on the remote control.

A dialog will appear on the screen indicating that you have

muted the sound. To

restore the sound, press the MUTE or VOLUME button. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

Selecting an input signal

Press the INPUT button on the projector.

Each time you press the button, the projector switches its

input port as below. RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO

Each time you press the button, the projector switches its RGB input port as below.

RGB IN1

● When the TURN ON is selected to the item SEARCH of OPTION menu the projector selects the RGB IN1 port at ﬁrst. If no input is detects at the RGB IN1 port, projector will check the RGB IN2 port.

Each time you press the button, the projector switches its video input port as below.

COMPONENT VIDEO

● When the TURN ON is selected to the item SEARCH of OPTION menu the projector selects the COMPONENT VIDEO port at ﬁrst. If no input is detected at the COMPONENT VIDEO port, projector will begin to check other ports.

Press the RGB button on the remote control to select an input port for RGB signal.

RGB IN2



Press the VIDEO button on the remote control to select an input port for video signal.

S-VIDEO  VIDEO



(36)

Page 30

Operating

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

ASPECT AUTO

BLAN

VIDEO

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

VOLUME

Searching an input signal

Press the SEARCH button on the remote control.

The projector will begin to check its input ports in order to

ﬁnd any input signals. Then when an input is found, the projector will stop

searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO

Selecting an aspect ratio

Press the ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect

ratio in turn.

At a RGB signal



NORMAL  4:3  16:9

At a video signal /no signal



4:3  16:9  SMALL

● The NORMAL mode keeps the original aspect ratio of the signal.

● At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT VIDEO input, only 16:9 mode can be selected.

● Performing the automatic adjustment initializes the aspect ratio setting.

Adjusting the zoom and focus

Use the zoom knob to adjust the screen size.

Use the focus ring to focus the picture.

Focus ring

Zoom knob

Page 31

ENGLISH

Operating

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

VIDEO

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

MAGNIFY

ASPECT AUTO

BLANK

HOME

PAGE UP

VOLUME

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

Using the automatic adjustment feature

Press the AUTO button on the remote control.

At a RGB signal



The vertical position, the horizontal position, the clock phase and horizontal size will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

At a video signal



The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the item

(30)

VIDEO FORMAT of the INPUT menu the signal type is identiﬁed automatically indep

. For a component video signal,

endently of this function.

● The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input.

Adjusting the position

Press the POSITION button on the remote control.

The “POSITION” indication will appear on the screen. Use the cursor buttons ▲/▼/◄/► to adjust the picture

position.

When you want to reset the operation, press the RESET button on the remote control during the operation.

To complete this operation do anything, the dialog will automatically disappear after a few seconds.

● When this function is performed at a video signal, a certain extra such as a line may appear outside a picture.

, press the POSITION button again. Even if you don’t

Correcting the keystone distortions

Press the KEYSTONE button on the remote control.

A dialog will appear on the screen to aid you in

the distortion.

Use the cursor buttons ▲/▼ to correct the distortion.

To close the dialog and complete this operation, press the KEYSTONE button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

● This function may not be work well with some input.

● The adjustable range for correcting will vary among inputs.

correcting

Page 32

Operating

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

OFF

MAGNIFY

ASPECT AUTO

BLANK

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

VIDEO

SEARC

STANDBY/ON

MAGNIFY

ASPECT AUTO

BLANK

HOME

PAGE UP

VOLUME

Using the magnify feature

Press the ON button of MAGNIFY on the remote control.

The “MAGNIFY” indication will appear on the screen (although the indication will disappear after several seconds with no operation.), and the projector will enter the MAGNIFY mode.

Use the cursor buttons ▲/▼ to adjust the zoom level.

To move the zoom area

, press the POSITION button in the MAGNIFY mode, then use the cursor buttons ▲/▼/◄/► to move the area. And to ﬁnalize the zoom area, press the POSITION button again.

To exit the MAGNIFY mode and restore the screen to normal, press the O button of MAGNIFY on the remote control.

● The projector automatically exits the MAGNIFY mode when the input signal changes, or when an operation of changing the display condition (automatic adjustment, etc.) is executed.

● Although in the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exit the MAGNIFY mode.

Freezing the screen

Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen, and

the projector will enter the FREEZE mode. To exit the FREEZ

press the FREEZE button again.

● The projector automatically exits the FREEZE mode when the input signal changes, or when one of the projector’s buttons or the remote control buttons of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME, MUTE, KEYSTONE, POSITION and MENU is pressed.

● If the projector continues projecting a still image for long time, the LCD panel might possibly be printed. Do not leave the projector in FREEZE mode for too long.

E mode and restore the screen to normal,

Temporarily blanking the screen

Press the BLANK button on the remote control.

The blank screen will be displayed instead of the screen of input signal. Please refer to the item BLANK of section SCREEN menu

To remove the blank screen and return to the input signal screen, press the BLANK button again.

● The projector automatically returns to the input signal screen when the input signal changes, or when one of the projector’s buttons or the remote control buttons are pressed.

(33).

Page 33

ENGLISH

Operating

Operating the computer screen

CAUTION ►Mistaken use of the mouse/keyboard control could damage

your equipment.

• While using this function, please connect only with a computer.

• Before connecting, read the manuals of the computer you will connect.

NOTE • It may not be possible to control notebook PC, and other computers with built-in pointing device (e.g. track ball), using this remote control. In this case, before connecting go into BIOS (system setup) and select external mouse, and disable the pointing device. In addition, the mouse may not function if the computer does not have the needed utility program. See your computer’s hardware manual for details.

• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s conﬁgurations and mouse drivers.

• The USB control can be used only for the functions listed below. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

• This function is not available while the lamp is warming up (the POWER indicator ﬂashes green), and while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu

screen.

USB mouse and keyboard control

Connect the projector’s USB port to the computer via the mouse cable.

Available function Remote control operation

Move pointer Use ▲, ▼, ◄, ► buttons

Left click with mouse Press ENTER button

Right click with mouse Press RESET button

Press keyboard’s HOME key

Press keyboard’s END key

Press keyboard’s PAGE UP key Press PAGE UP button

Press keyboard’s PAGE DOWN key Press PAGE DOWN button

Press keyboard’s ESC key

Press HOME button

Press END button

Press ESC button

Page 34

Multifunctional settings

MENU [RGB

]

:SELECT

PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN

BRIGHT CONTRAS

T GAMMA COLOR TEMP COLOR TINT SHARPNES

S PROGRESSIVE MY MEMORY

+0 +0

#1 DEFAUL

LOW

+0 +0 +0

TURN OFF

SAVE 1

EASY MENU

ASPECT KEYST

ONE MODE BRIGHT CONTRAST COLO

R TINT SHRPNESS WHISPER MIRROR RESE

T FILTER TIME LANGUAGE

4:3

NORMAL +0 +0 +0 +0 +3

NORMAL

EXECUTE

ENGLISH

Go To Advance Menu...

VIDEO

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

STAND BY/ ON INPU T

POWE R

TEM P

LAM P

VIDEO

RGB

SEARC

STANDBY/ON

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLAN

HOME

PAGE UP

PAGE DOWN

END

MUTE

VOLUME

KEYSTONE

POSITION

ENTE

RESE

Multifunctional settings

Using the menu function

This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION and EASY MENU. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.

MENU button

Cursor buttons

ENTER button

RESET button

Press the MENU button on the remote control or one of the

cursor buttons on the projector.

The advanced MENU or EASY MENU will appear

Use the cursor buttons ▲/▼ to select a menu.

At the EASY MENU



If you want to change it to the advanced MENU, select the "Go to Advanced Menu".

At the advanced MENU



Select a menu of PICTURE, IMAGE, INPUT, SETUP, SCREEN or OPTION. If you want to change it to the EASY MENU, select the EASY MENU.

Then press the cursor button ► on the projector or remote

control, or the ENTER button on the remote control to progress. The display of the selected menu will be active.

Use the cursor buttons ▲/▼ to select an item to operate.

Then press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. The operation menu of the selected item will appear.

Use the cursor buttons▲/▼ to operate the item.

When you want to reset the operation, press the RESET button on the remote control during the operation. Note that items whose functions are performed simultaneously with operation (ex. LANGUAGE, H PHASE etc.) aren't reset.

When you want to return to the previous display, press the cursor b the projector or remote control, or the ESC button on the remote control.

Press the MENU button on the remote control again to close the menu and

complete this operation. Even if you don't do anything, the dialog will automatically disappear after about 10 seconds.

Advanced MENU

EASY MENU

utton ◄ on

Page 35

EASY Menu

EASY MENU

ASPECT KEYST

ONE MODE BRIGHT CONTRAS

COLO

R TINT SHRPNESS WHISPER MIRROR RESE

T FILTER TIME LANGUAGE

4:3

NORMAL +0 +0 +0 +0 +3

NORMAL

EXECUTE

ENGLISH

Go To Advance Menu...

With the EASY MENU, items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control. Then perform it referring to the following table.

Item Description

Using the buttons ◄/► switches the mode for aspect ratio. See the item ASPECT of section IMAGE menu

Using the buttons ◄/► corrects the keystone distortion. See the item KEYSTONE of section SETUP menu (32).

Using the buttons ◄/► switches the mode of picture type.The modes of picture type are combinations of a mode of GAMMA and a mode of COLOR TEMP. Choose a suitable mode according to the projected source.

NORMAL

CINEMA



DYNAMIC



NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT) CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT) DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT)

• When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the MODE is “CUSTOM”. Please refer to the items GAMMA COLOR TEMP

(26) of PICTURE menu.

Using the buttons ◄/► adjusts the brightness. See the item BRIGHT of section PICTURE menu (25).

Using the buttons ◄/► adjusts the contrast. See the item CONTRAST of section PICTURE menu (25).

Using the buttons ◄/► adjusts the strength of whole color. See the item COLOR of section PICTURE menu (26).

Using the buttons ◄/► adjusts the tint. See the item TINT of section PICTURE menu (26).

ASPECT

KEYSTONE

MODE

BRIGHT

CONTRAST

COLOR

TINT

Multifunctional settings

(28).

(25) and

ENGLISH

Page 36

Multifunctional settings

EASY Menu (continued)

Item Description

SHARPNESS

WHISPER

MIRROR

RESET

FILTER TIME

LANGUAGE

Go To

Advanced Menu

Using the buttons ◄/► adjusts the sharpness. See the item SHARPNESS of section PICTURE menu (26).

Using the buttons ◄/► turns off/on the whisper mode. See the item WHISPER of section SETUP menu (32).

Using the buttons ◄/► switches the mode for mirror status. See the item MIRROR of section SETUP menu (32).

Performing this item resets all of the items of EASY MENU except FILTER TIME and LANGUAGE. A dialog is displayed to make sure. Selecting RESET using the button ▲ performs reset.

Performing this item resets the ﬁlter timer which counts use time of air ﬁlter. A dialog is displayed to make sure. Selecting RESET using the button ▲ performs reset. See the item FILTER TIME of section OPTION menu (37).

Select the LANGUAGE to toggle the menu language. Refer to description of LANGUAGE in the SCREEN menu (33).

Select the “Go To Advanced Menu” to use the IMAGE, INPUT, SETUP, SCREEN or OPTION.

menu of PICTURE,

Page 37

ENGLISH

Multifunctional settings

MENU [RGB

]

:SELECT

PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN

BRIGHT CONTRAS

T GAMMA COLOR TEMP COLOR TINT SHARPNES

S PROGRESSIVE MY MEMOR

+0 +0

#1 DEFAUL

LOW

+0 +0 +0

TURN OFF

SAVE

GAMMA [CUSTOM 1

]

ENTER :

PICTURE Menu

With the PICTURE menu, items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table.

Item Description

BRIGHT Using the buttons ▲/▼ adjusts the brightness. : Light  Dark

CONTRAST Using the buttons ▲/▼ adjusts the contrast. : Strong

Using the buttons ▲/▼ switches the GAMMA mode. :

#1 DEFAULT

#1 CUSTOM  #2 DEFAULT



Weak

GAMMA

#3 CUSTOM

 #3 DEFAULT  #2 CUSTOM

To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM

Selecting a mode of CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones.

Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼.

You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern  Gray scale of 9 steps Ramp  Gray scale of 15 steps Eight of equalizing bars corresponds to eight of tone level of test

pattern except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar.

Page 38

Multifunctional settings

COLOR TEMP

ENTER :

OFFSET

GAIN

PICTURE Menu (continued)

Item Description

Using the buttons ▲/▼ switches the mode of color temperature.

HIGH  MIDDLE  LOW

To adjust CUSTOM

Selecting the CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the OFFSET and/or GAIN of CUSTOM mode.

OFFSET adjustments change the color intensity

COLOR TEMP

COLOR

TINT

SHARPNESS

on the whole tones of the test pattern. GAIN adjustments mainly affect color intensity

on the brighter tones of the test pattern. Choose an item using the buttons ◄/►, and adjust the level using

the buttons ▲/▼. You can display a test pattern for checking the effect of your

adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern  Gray scale of 9 steps Ramp  Gray scale of 15 steps Using the buttons ▲/▼ adjusts the strength of whole color.

Strong

• This item can be selected only at a video signal. Using the buttons ▲/▼ adjusts the tint.

Green  Red

• This item can be selected only at a video signal except for SECAM.

Using the buttons ▲/▼ adjusts the sharpness.

Strong



Weak

CUSTOM



Page 39

ENGLISH

PICTURE Menu (continued)

Item Description

Using the buttons ▲/▼ switches the progressive mode.

TV  FILM  TURN OFF

• This function performs only at an interlaced signal of a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input of 525i

PROGRESSIVE

(480i) or 625i (576i) signal.

• When the TV or FILM is selected, the screen image will be crisper. The FILM mode is adaptable to the 2-3 Pull-Down system to the conversion. But these may cause a certain defect (for example, jagged line) of the picture at a quick moving object. In such a case, please select the TURN OFF, even though the screen image may lose the crisp.

Selecting a mode of MY MEMORY using the buttons ▲/▼ and then pressing the button ► or the ENTER button performs each function.

Multifunctional settings

LOAD1  LOAD2  LOAD3  LOAD4

MY MEMORY

SAVE4

SAVE3  SAVE2  SAVE1



This projector has 4 numbered memories for adjustment data. Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on the memory whose number corresponds with the command’ s number, and adjusts the picture automatically depending on the data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current adjustment data on the memory whose number corresponds with the command’s number.

Page 40

Multifunctional settings

MENU [RGB

]

:SELECT

PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN

ASPEC

T OVER SCAN V POSITION H POSITION H PHAS

E H SIZE AUTO ADJUST

4:3 95 25 142 16 1344

IMAGE Menu

With the IMAGE menu, items shown in the table below can be performed.

Item Description

Using the buttons ▲/▼ switches the mode for aspect ratio. At a RGB signal

4:3  16:9  NORMAL

At a video signal / no signal

ASPECT

OVER SCAN

V POSITION

H POSITION

H PHASE

4:3  16:9  SMALL

• The NORMAL mode keeps the original aspect ratio of the signal.

• At a HDTV signal of 1125i (1080i)

or 750p (720p) of COMPONENT

VIDEO input, this item can't be selected.

• Performing the automatic adjustment initializes the aspect ratio setting.

Using the buttons ▲/▼ adjusts the over-scan ratio.

Large (It reduces picture)  Small (It magniﬁes picture)

• This item can be selected only at a video signal.

• When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small.

Using the buttons ▲/▼ adjusts the vertical position.

Up  Down

Using the buttons ▲/▼ adjusts the horizontal position.

Left  Right

Using the buttons ▲/▼ adjusts the horizontal phase to eliminate ﬂicker.

Right  Left

• This item can be selected only at a RGB signal or a component video signal.

Page 41

ENGLISH

IMAGE Menu (continued)

Item Description

Using the buttons ▲/▼ adjusts the horizontal size.

Large  Small

H SIZE

AUTO ADJUST

• This item can be selected only at a RGB signal.

• When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please reset the adjustment pressing the RESET button on the remote control during this operation.

Selecting this item performs the automatic adjustment feature.

At a RGB signal

At a video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the item VIDEO FORMAT of INPUT menu. For a component video signal, the signal type is identiﬁed automatically independently of this function.

• The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input.

Multifunctional settings

Page 42

Multifunctional settings

MENU [RGB

]

:SELECT

PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU

COLOR SPACE COMPONENT VIDEO FORMAT FRAME LOCK INFORMATION

AUTO COMPONENT AUTO TURN ON

INPUT Menu

With the INPUT menu, items shown in the table below can be performed.

Item Description

Using the buttons ▲/▼ switches the mode for color space.

AUTO  RGB  SMPTE240  REC709  REC601

COLOR SPACE

COMPONENT

VIDEO FORMAT

FRAME LOCK

•

This item can be selected only at a RGB signal or a component video signal.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well at some signals. In such a case, it might be good to select the SMPTE240 or the REC709.

Using the buttons ▲/▼ switches the function of COMPONENT VIDEO port.

COMPONENT  SCART RGB

When the SCART RGB is selected, the COMPONENT VIDEO port function as a port for a SCART RGB signal input. A SCART adapter and SCART cable realize a SCART RGB input to the projector. For details, ask your dealer.

Using the buttons ▲/▼ switches the mode for video format.

AUTO  NTSC  PAL  SECAM N-PAL  M-PAL  NTSC4.43

• This item performs only at a video signal from the VIDEO port or the S-VIDEO port. For a component video signal, the signal type is identiﬁed automatically independently of this function.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well at some signals. If the picture becomes unstable (ex. an irregular picture, a color lack), please select the mode depending on the input signal.

Using the buttons ▲/▼ turns the frame lock function on/off.

TURN ON  TURN OFF

• This item performs only at a RGB signal with vertical frequency of 50 to 60 Hz for the models 8755C, or 50 to 72Hz for the model 8063.

• When the TURN ON is selected, a moving picture is displayed more smoothly.

• This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF.

Page 43

ENGLISH

INPUT Menu (continued)

INPUT-INFORMATION

RGB

1024x768 @60.0

FRAME LOCK

INPUT-INFORMATION

S-VIDEO

SECAM

AUTO

INPUT-INFORMATION

COMPONENT

576i @50

SCART RGB

Item Description

Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.

Multifunctional settings

INFORMATION

• The “FRAME LOCK” message on the dialog means the frame lock function is working (30).

• The “SCART RGB” message means the COMPONENT VIDEO port is working as a SCART RGB input port. Please refer to the item COMPONENT in this section.

(30)

• This item is can't be selected at no signal.

Page 44

Multifunctional settings

MENU [RGB

]

:SELECT

PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN

KEYST

ONE WHISPER MIRROR VOLUM

+0 NORMAL NORMAL 16

SETUP Menu

With the SETUP menu, items shown in the table below can be performed.

Item Description

Using the buttons ▲/▼ corrects the keystone distortion.

Upper in the data  Lower in the data

• The adjustable range of this function will vary with the type of input signal. At some signals, this function may not work well.

KEYSTONE

WHISPER

• When the V:INVERT or the H&V:INVERT is selected under the item MIRROR, if the projector screen is inclined or if the projector is angled downward, this function may not work correctly.

• When the zoom adjustment is set to the TELE side, this correction may be excessive. This function should be used with zoom set to WIDE whenever possible.

Using the buttons ▲/▼ turns off/on the whisper mode.

NORMAL

WHISPER



• When the WHISPER is selected, acoustic noise and screen brightness are reduced.

Using the buttons ▲/▼ switches the mode for mirror status.

MIRROR

VOLUME

NORMAL

H:INVERT  V:INVERT  H&V:INVERT



Using the buttons ▲/▼ adjusts the volume.

High  Low

Page 45

ENGLISH

Multifunctional settings

ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO

NORSK  NEDERLANDS  PORTUGUÊS  

 SVENSKA   SUOMI  POLSKI

MENU [RGB

]

:SELECT

PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN

LANGUAGE MENU POSITION OSD BRIGHT BLANK START UP MyScreen MyScreen Lock MESSAGE

ENGLISH

5 BLACK ORIGINA

TURN OFF TURN ON

SCREEN Menu

With the SCREEN menu, items shown in the table below can be performed.

Item Description

Using the buttons ▲/▼ switches the OSD (On Screen Display) language.

LANGUAGE

Using the buttons ◄/►/▲/▼ adjusts the menu position.

MENU POSITION

OSD BRIGHT

BLANK

To quit the operation, press the MENU button on the remote control or keep no operation for 10 seconds.

Using the buttons ▲/▼ switches the brightness level of the OSD (On Screen Display).

Bright  Dark

Using the buttons ▲/▼ switches the mode the blank screen. The blank screen is the screen for the temporarily blanking feature (20). It is displayed by pressing the BLANK button on the remote control.

MyScreen

ORIGINAL



BLUE  WHITE  BLACK



MyScreen is the screen you can register a desired screen. ORIGINAL screen is the existing standard screen. and BLACK are non-patterned (plain) screens in each color.

• To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLACK screen after several minutes.

• For the MyScreen, please refer to the item MyScreen (34).

BLUE, WHITE

Page 46

Multifunctional settings

SCREEN Menu (continued)

Item Description

Using the buttons ▲/▼ switches the mode the start up screen. The start up screen is the screen displayed when no signal or an unsuitable signal is detected.

MyScreen

MyScreen is the screen you can register a desired screen. ORIGINAL screen is the existing standard screen. When the TURN

START UP

My Screen

My Screen Lock

OFF is selected, the BLUE screen is used.

• To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLANK screen after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it will change to the BLACK screen.

• For the MyScreen, please refer to the item MyScreen About the BLUE, BLACK and BLANK screens, please refer to the item BLANK (33).

This item functions for capturing the MyScreen of the blank screen and the start up screen. Please execute displaying the input including the picture you want to capture.

1. Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing the picture from the current screen. Please wait for the target picture to be displayed, and press the ENTER button on the remote control when the picture is display. The picture will freeze and the frame for capturing appears.

To stop performing, press the RESET or ESC button on the

remote control.

2. Using the buttons ◄/►/▲/▼ adjust the frame position. Please move the frame to the position of the picture which you want to use.

To start registration, press the ENTER button on the remote

control.

To restore the screen and return to the previous dialog, press the

RESET or ESC button on the remote control.

Registration takes several minutes. When the registration is completed, the registered screen and the message “MyScreen registration is ﬁnished.” are displayed for several seconds. If the registration failed, the message “A capturing error has occurred. Please try again.” is displayed.

Using the buttons ▲/▼ turns on/off the MyScreen lock function.

TURN ON

When the TURN ON is selected, the item MyScreen cannot be performed. Use this function for protecting the current MyScreen.

ORIGINAL  TURN OFF



TURN OFF



below

Page 47

ENGLISH

SCREEN Menu (continued)

Item Description

Using the buttons ▲/▼ turns on/off the message function.

TURN ON

When the TURN ON is selected, the following message function works.

MESSAGE

“AUTO IN PROGRESS” while automatically adjusting ”NO INPUT IS DETECTED” ”SYNC IS OUT OF RANGE”

”Searching ....” while searching for an input signal

”Detecting….” when an input signal is detected The indication of the input signal by changing The indication of the aspect ration by changing .

TURN OFF



Multifunctional settings

Page 48

Multifunctional settings

AUTO OFF

ENABL

AUTO OFF

DISABLE

MENU [RGB

]

:SELECT

PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MEN

SEARC

AUT

O OFF LAMP TIME FILTER TIME SERVICE

TURN ON

0 0 0

OPTION Menu

With the OPTION menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress, except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table.

Item Description

Using the buttons ▲/▼ turns on/off the message function.

TURN ON

When the TURN ON is selected, detecting no signal automatically cycles through input ports in order of following. Then when an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state before the operation.

RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO

Using the buttons ▲/▼ adjusts the time to count down to automatically turn the projector off

Long (max. 99 minutes)  Short (min. 0 minute = DISABLE)

TURN OFF



AUTO OFF

LAMP TIME

When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with a no-signal or an unsuitable signal reaches at the set time, the projector lamp will go off and the power indicator begins blinking. Please refer to the section “Turning off the power” (16).

The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the use time of the lamp. Pressing the RESET button on the remote control for about 3 seconds displays a dialog. To reset the lamp time, select the RESET using the button ▲.

RESET

CANCEL



• Please reset the lamp time only when you have replaced the lamp, for correct messages about the lamp.

• About the lamp replacement, please see the section "Lamp" (



38, 39).

Page 49

ENGLISH

OPTION Menu (continued)

Item Description

The ﬁlter time is the time counted after the last resetting. It is shown in the OPTION menu as the use time of the air ﬁlter. Pressing the RESET button on the remote control for about 3 seconds displays a dialog. To reset the ﬁlter time, select the RESET

FILTER TIME

SERVICE

using the button ▲.

RESET

• Please reset the ﬁlter time only when you have cleaned or replaced the air ﬁlter, for correct messages about the air ﬁlter.

• About the caring the air ﬁlter, please see the section "Air ﬁlter" (

40). Selecting this item displays the SERVICE menu.

Select an item using the buttons ▲/▼, and press the button ► or the ENTER button on the remote control to progress.

FAN SPEED

Using the buttons ▲/▼ switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. projector is noisier when the HIGH is selected.

HIGH  NORMAL

GHOST

1. Select a color element of ghost using the buttons ▲/▼ and press the cursor button ► or the ENTER button on the remote control to progress.

2. Adjust the selected element using the buttons ▲/▼ to disappear

ghost.

FACTORY RESET

Selecting RESET using the button ▲ performs this function. function, all the items in all of menu will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME and LANGUAGE are not reset.

RESET

CANCEL





CANCEL



Multifunctional settings



FACTORY RESET  GHOST

Note that the

By this

Page 50

Maintenance

Lamp

WARNING

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to ﬂy into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

►About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in the US) For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.

Disconnect

the plug

from the

power

• Before replacing the lamp, turn the projector off and unplug the power

outlet

cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

• Use only the lamp of the speciﬁed type.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• If the indicators or a message prompts you to replace the lamp (see the section "Related Messages" and "Regarding the indicator Lamps"), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

Page 51

ENGLISH

Maintenance

Lamp (continued)

When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible.

Turn the projector off, and unplug the power cord. Allow the lamp to cool for

at least 45 minutes. To prepare a new lamp, contact your dealer and tell the lamp type number

= 456-8063. If the projector is mounted on the ceiling, or if the lamp has

broken, also ask the dealer to replace the lamp.

In the case of replacement by yourself,

After making sure that the projector has

cooled adequately, slowly turn over the

projector, so that the bottom is facing up.

Please unhook the claws of the lamp cover

using a minus screwdriver or similar, and

remove the lamp cover.

Loosen the 2 screws (marked by arrow) of

the lamp, and slowly pick up the lamp by the

handles.

Insert the new lamp, and retighten ﬁrmly two

screws that are loosened in the previous

process to lock it in place.

Interlocking the 2 tabs of the lamp cover to

the projector, position the lamp cover on the projector. Then push the center point of two claws to ﬁx the lamp cover.

Slowly turn the projector so that the top is

facing up.

Turn the projector on, and reset the lamp time

using the LAMP TIME function of OPTION

(

36)



Lamp cover

Claws

Screws marked

by arrow

Tabs

Center point of claws

Claws

NOTE • When the lamp has been replaced after the message of "THE POWER WILL TURN OFF AFTER 0hr." is displayed, complete the following operation within 10 minutes of switching power on.

• Incorrectly resetting of the lamp timer (resetting without replacement, or

neglect of resetting after replacement) will result in incorrect message functions.

Page 52

Maintenance

Air ﬁlter

WARNING ►Before caring, make sure the power switch is off and the

power cable is not plugged in, then allow the projector to cool sufﬁciently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Use only the air ﬁlter of the speciﬁed type. Do not use the projector with the air ﬁlter and ﬁlter cover removed. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a ﬁre, an electric shock, and and/or malfunction to the projector

CAUTION ►Please replace the air ﬁlter when it is damaged or too soiled,

and also when you replace the lamp.

When the indicators or a message prompts you to clean the air ﬁlter, clean the air ﬁlter as soon as possible rise and the power may be automatically turned off for malfunction prevention.

Turn the projector off, and unplug the power cord.

Allow the projector to cool for at least 45 minutes. And

prepare a vacuum cleaner.

After making sure that the projector is cool adequately,

slowly turn the projector so that the lens-side is facing up. Please be careful for a projector not to fall. While the projector is placed lens-side up, hold the projector.

Putting a ﬁnger on the ﬁlter cover’s knob, slide the

ﬁlter cover in the direction of the arrow to remove it

Holding the air ﬁlter’s knob, pull the air ﬁlter off.

Apply a vacuum cleaner to the vent of the projector for the

air ﬁlter. And then slowly turn the projector bottom up

Apply a vacuum cleaner to the air ﬁlter and ﬁlter cover.

Please replace the air ﬁlter when it is damaged or too soiled. To prepare a new air ﬁlter, contact your dealer and tell the air ﬁlter type number An air ﬁlter of speciﬁed type will come even with the replacement lamp for this projector.

Position the cleaned air ﬁlter or a new air ﬁlter into place, and push the points

of "PUSH" word with claws to ﬁx the air ﬁlter.

Replace the ﬁlter cover and snap it back into place.

. If the air ﬁlter becomes clogged by dust or the like, internal temperatures

= NJ09702.

Filter cover’s knob

Filter cover

Air ﬁlter’s knob

Air ﬁlter

Slowly turn the projector so that the top is facing up.

Turn the projector on, and reset the ﬁlter time using the FILTER TIME

10.

function of OPTION menu

NOTE

or neglect of resetting after replacement) will result in incorrect message

functions.

• Incorrectly resetting of the ﬁlter timer (resetting without replacement,

(37)

Page 53

ENGLISH

Maintenance

Other care

WARNING ►Before caring, make sure the power switch is off and the

power cable is not plugged in, and then allow the projector to cool sufﬁciently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Never try to care for the inside of the projector personally. Doing is so dangerous. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a ﬁre, an electric shock, and and/or malfunction to the projector.

• Don’t put a container containing water, cleaner or chemicals near the projector.

• Don’t use aerosols or sprays. CAUTION ►Please take right care of the projector according to the

following. Incorrect care could cause not only an injury but adverse inﬂuence such as discoloration, peeling paint, etc.

• Do not use cleaner or chemicals other than those listed below.

• Do not polish or wipe with hard objects.

Inside of the projector

In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every 2 years.

Caring for the lens

If the lens is ﬂawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of the handling.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufﬁciently After making sure that the projector is cool adequately, lightly wipe the lens

with a commercially available lens-cleaning wipe. Do not touch the lens

directly with your hand.

Caring for the cabinet and remote control

Incorrect care could have adverse inﬂuence such as discoloration, peeling paint, etc.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufﬁciently. After making sure that the projector is cool adequately, lightly wipe with gauze

or a soft cloth. If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

Page 54

Troubleshooting

NO INPUT IS DETECTED

ON ***

SYNC IS OUT OF RANGE

ON *** fH *****kHz fV *****Hz

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message Description

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

THE POWER WILL TURN OFF

AFTER ** hr.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

THE POWER WILL TURN OFF

AFTER 0 hr.

CHECK THE AIR FLOW

If the same message is displayed after the treatment, or if a

The time the lamp timer has counted is approaching 2000 hours.

Preparation of a new lamp, and an early lamp change is recommended. After you have change the lamp, please be sure to reset the lamp timer (36).

The time the lamp timer has counted is approaching 2000 hours, so a lamp change within ** hours is recommended.

When lamp usage reaches 2000 hours, the power will automatically be turned off. Please change the lamp by referring to the section “Lamp”. After you have changed the lamp, please be sure to reset the lamp timer (36).

As the time the lamp timer has counted has reached 2000 hours, the power will soon be automatically turned off.

Please immediately turn the power off, and change the lamp by referring to the section “Lamp”. After changing the lamp, please be sure to reset the lamp timer (36).

There is no input signal.

Please conﬁrm the signal input connection, and the status of the signal source.

The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit.

Please conﬁrm the specs for this unit or the signal source specs.

The internal portion temperature is rising.

Please turn the power OFF, and allow the unit to cool down at least 20 minutes. After having conﬁrmed the following items, please turn the power ON again.

• Is there blockage of the air passage aperture?

• Is the air ﬁlter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please set the

•

HIGH at the FAN SPEED of the item SERVICE of the OPTION menu.

Page 55

ENGLISH

Troubleshooting

Related messages (continued)

Message Description

CLEAN THE AIR FILTER

POWER OFF FIRST,

THEN CLEAN THE AIR

FILTER.

AFTER CLEANING THE AIR

FILTER,

RESET THE FILTER TIMER.

A note of precaution when cleaning the air ﬁlter.

Please immediately turn the power OFF, and clean or change the air ﬁlter by referring to the “Air Filter” section of this manual. After you have cleaned or changed the air ﬁlter, please be sure to reset the ﬁlter timer

(37).

NOTE • A lamp has a ﬁnite product life. Lamps are characterized by the fact that, after long hours of usage, a lamp will no longer light up, or the lamp will break or burst, etc. This projector is equipped with an automatic shut-down function, such that the power will automatically be turned off when lamp usage time has reached 2000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this projector.

Page 56

Troubleshooting

Regarding the indicator lamps

Lighting and ﬂashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company.

POWER

indicator

Lighting

In Orange

Blinking

In Green

Lighting

In Green

Blinking

In Orange

Blinking

In Red

Blinking

In Red

Lighting

In Red

Blinking

In Red

Lighting

In Red

LAMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

(discretionary)

Lighting

In Red

Blinking

In Red

TEMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

(discretionary)

Turned

off

Turned

off

Description

The projector is in a standby state.

Please refer to the section “Power On/Off”.

The projector is warming up.

Please wait.

The projector is in an on state.

Ordinary operations may be performed.

The projector is cooling down.

Please wait.

The projector is cooling down. A certain error has been detected.

Please wait until the POWER indicator ﬁnishes blink, and then perform the proper response measure using the item descriptions below as reference.

The lamp does not light, and there is a possibility that interior portion has become heated.

Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufﬁciently cooled down, please make conﬁrmation of the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air ﬁlter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please change the lamp by referring to the section “Lamp”.

The lamp cover has not been properly ﬁxed (attached).

Please turn the power off, and allow the unit to cool down at least 45 minutes. After the projector has sufﬁciently cooled down, please make conﬁrmation of the attachment state of the lamp cover. After performing any needed maintenance, turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company.

Page 57

ENGLISH

Regarding the indicator lamps (continued)

Troubleshooting

POWER

indicator

Blinking

In Red

Lighting

In Red

Blinking

In Red

Lighting

In Red

Lighting

In Green

Lighting

In Green

LAMP

indicator

Turned

blinking in Red

indicator

off

Alternative

Simultaneous

TEMP

Blinking

In Red

Lighting

In Red

Description

The cooling fan is not operating.

Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufﬁciently cooled down, please make conﬁrmation that no foreign matter has become caught in the fan, etc., and then turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company.

There is a possibility that the interior portion has become heated.

• Is there blockage of the air passage aperture?

• Is the air ﬁlter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please set the HIGH at the FAN SPEED of the item SERVICE of the OPTION menu.

There is a possibility that the interior portion has become overcooled.

Please use the unit within the usage temperature parameters (5°C to 35°C). After the treatment, resent the power to ON.

It is time to clean the air ﬁlter.

Please immediately turn the power OFF, and clean or change the air ﬁlter by referring to the section “Air Filter”. After cleaning or changed the air ﬁlter, please be sure to reset the ﬁlter timer. After the treatment, resent the power to ON.

NOTE • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off

. In such a case, press the “” (OFF) side of the power switch, and wait at least 45 minutes. After the projector has sufﬁciently cooled down, please make conﬁrmation of the attachment state of the lamp and lamp

cover, and then turn the power on again.

Page 58

Troubleshooting

Phenomena that may easily be mistaken for machine defects

WARNING ►Never use the projector if abnormal operations such as

smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company.

Before requesting repair, please check in accordance with the following chart.

This operation sometimes resolves your problem.

If the situation cannot be corrected,

The projector’s microprocessor may need to be reset. Please push the

Restart switch by using a cocktail stick or similar and the projector will restart. Some setting may be wrong. Please use the FACTORY RESET function of

SERVICE menu in the OPTION menu

default. Then, if the problem is not removed after maintenance, please contact your dealer

or service company.

(37)

to reset all settings to factory

Phenomenon Cases not involving a machine defect

The electrical power cord is not plugged in.

Correctly connect the power cord.

The power switch is not set to the on position.

Set the power switch to [ | ] (On).

The main power source has been interrupted during operation such as by a power outage (blackout), etc.

Power does not

come on.

Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufﬁciently cooled down, please turn the power on again.

Either there is no lamp and/or lamp cover, or either of these has not been properly ﬁxed.

Reference

page

38, 39

Page 59

ENGLISH

Troubleshooting

Phenomena that may easily be mistaken for machine defects (continued)

Phenomenon Cases not involving a machine defect

The lens cover is closed.

Remove the lens cover.

The signal cables are not correctly connected.

Correctly connect the connection cables.

No pictures are

displayed.

The brightness is adjusted to an extremely low level.

Adjust the BRIGHT to a higher level using the menu function or the remote control.

The computer cannot detect the projector as a plug and play monitor.

Make sure that the computer’s can detect a plug and play monitor using other plug and play monitor.

Color settings are not correctly adjusted.

Colors have a

faded- out

appearance, or

Color tone is

poor.

Perform picture adjustments by changing the COLOR

COLOR, TINT and/or COLOR SPACE settings,

TEMP, using the menu functions.

COLOR SPACE setting is not suitable.

Change the COLOR SPACE setting to AUTO, RGB, SMPTE240 , REC709 or REC601.

The brightness and/or contrast are adjusted to an extremely low level.

Adjust the BRIGHT and/or CONTRAST settings to a higher level using the menu function.

Pictures appear

dark.

The WHISPER function is working.

Select the NORMAL to the item WHISPER in the SETUP menu.

The lamp is approaching the end of its product lifetime.

Replace the lamp.

Either the focus and/or horizontal phase settings are not properly.

Pictures appear

blurry.

Adjust the focus using the focus ring, and/or H PHASE using the menu function.

The lens is dirty or misty.

Clean the lens by referring to the section “Caring for the lens”.

Reference

page

4, 16

23, 25

23, 25,

24, 25

24, 32

38, 39

18, 28

NOTE • Although bright spots or dark spots may appear on the screen, this

is a unique characteristic of liquid crystal displays, and such do not constitute or

imply a machine defect.

Page 60

Warranty And After-Service

Warranty and after-service

If a problem occurs with the equipment, ﬁrst refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or the service company. They will tell you what warranty condition is applied.

Speciﬁcations

NOTE • This speciﬁcations are subject to change without notice.

Item Speciﬁcation

Product name Liquid crystal projector

Liquid Crystal panel

Lens Zoom lens F=1.7 ~ 1.9 f=21.8 ~ 26.2 mm Lamp 165W UHB Power Supply AC100-120V/2.7A, AC220-240V/1.5A Power Consumption 240W Temperature range 5 ~ 35°C (Operating)

Size

Weight (mass) 2.5 kg

Ports

Optional parts

Panel size 1.8 cm (0.7 type) Drive system TFT active matrix

8063

Pixels

Lamp456-8063 Air ﬁlter NJ09702 Others • Please consult your dealer.

CP-S335: 480,000 pixels (800 horizontal x 600 vertical) CP-X340: 786,432 pixels (1024 horizontal x 768 vertical)

8755C

297 (W) x 64 (H) x 233 (D) mm (Not including protruding parts)

• Please refer to the following ﬁgure.

RGB input:

RGB IN1 ..D-sub 15pin mini x1 RGB IN2 ..D-sub 15pin mini x1

RGB output:

RGB OUT D-sub 15pin mini x1

Communication port:

CONTROL ............D-sub 9pin x1

USB ....................... USB(B) x1

Video input:

COMPONENT VIDEO

Y ............................... RCA x1

....................... RCA x 1

B/PB

S-Video ................................ 1

Video .................................... 1

Audio input:

AUDIO IN1 ...... Stereo mini x1

AUDIO IN2 ...... Stereo mini x1

Audio output:

AUDIO OUT ... Stereo mini x1

...................... RCA x 1

R/PR

Page 61

ENGLISH

Speciﬁcations (continued)

79.7

80.0

64.2

65.4

32.2

237.4

232.8

297.0

84.5

Speciﬁcations

[unit: mm]

Page 62

Page 63

Projector

8063/8755C

User's Manual – Operating Guide Technical

Example of computer signalExample of computer signal

Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode

720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA VGA (72Hz) 640 x 480 37.5 75.0 VESA VGA (75Hz) 640 x 480 43.3 85.0 VESA VGA (75Hz) 800 x 600 35.2 56.3 VESA SVGA (56Hz) 800 x 600 37.9 60.3 VESA SVGA (60Hz) 800 x 600 48.1 72.2 VESA SVGA (72Hz) 800 x 600 46.9 75.0 VESA SVGA (75Hz) 800 x 600 53.7 85.1 VESA SVGA (85Hz)

832 x 624 49.7 74.5 Mac 16” mode 1024 x 768 48.4 60.0 VESA XGA (60Hz) 1024 x 768 56.5 70.1 VESA XGA (70Hz) 1024 x 768 60.0 75.0 VESA XGA (75Hz) 1024 x 768 68.7 85.0 VESA XGA (75Hz) 1152 x 864 67.5 75.0 VESA SXGA (75Hz) 1280 x 960 60.0 60.0 VESA SXGA (60Hz)

1280 x 1024 64.0 60.0 VESA SXGA (60Hz) 1280 x 1024 80.0 75.0 VESA SXGA (75Hz) 1280 x 1024 91.2 85.0 VESA SXGA (85Hz) 1600 x 1200 75.0 60.0 VESA UXGA (60Hz)

TECHNICAL

NOTE • Be sure to check jack type, signal level, timing and resolution

before connecting this projector to a computer.

• Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

• Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above.

• Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical.

• Automatically adjustment may not function correctly with some input signals.

• The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G.

Page 64

Example of computer signal

Initial set signalsInitial set signals

The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu.

Data Data

H. Sync. V. Sync.

Sync (A) Sync (a)

Back porch (B) Front porch (D) Back porch (b) Front porch (d)

Display interval (C)

Computer/

Signal

TEXT 2.0 3.0 20.3 1.0 TEXT 3 42 400 1 VGA (60Hz) 3.8 1.9 25.4 0.6 VGA (60Hz) 2 33 480 10 VGA (72Hz) 1.3 3.8 20.3 1.0 VGA (72Hz) 3 28 480 9 VGA (75Hz) 2.0 3.8 20.3 0.5 VGA (75Hz) 3 16 480 1 VGA (85Hz) 1.6 2.2 17.8 1.6 VGA (85Hz) 3 25 480 1

SVGA (56Hz) 2.0 3.6 22.2 0.7 SVGA (56Hz) 2 22 600 1 SVGA (60Hz) 3.2 2.2 20.0 1.0 SVGA (60Hz) 4 23 600 1 SVGA (72Hz) 2.4 1.3 16.0 1.1 SVGA (72Hz) 6 23 600 37 SVGA (75Hz) 1.6 3.2 16.2 0.3 SVGA (75Hz) 3 21 600 1 SVGA (85Hz) 1.1 2.7 14.2 0.6 SVGA (85Hz) 3 27 600 1

Mac 16" mode 1.1 3.9 14.5 0.6 Mac 16" mode 3 39 624 1

XGA (60Hz) 2.1 2.5 15.8 0.4 XGA (60Hz) 6 29 768 3 XGA (70Hz) 1.8 1.9 13.7 0.3 XGA (70Hz) 6 29 768 3 XGA (75Hz) 1.2 2.2 13.0 0.2 XGA (75Hz) 3 28 768 1 XGA (85Hz) 1.0 2.2 10.8 0.5 XGA (85Hz) 3 36 768 1

1152 x 864

(75Hz)

1280 x 960

(60Hz)

1280 x 1024

(60Hz)

1280 x 1024

(75Hz)

1280 x 1024

(85Hz)

1600 x 1200

(60Hz)

Horizontal signal timing (μs)

(A) (B) (C) (D) (a) (b) (c) (d)

1.2 2.4 10.7 0.6

1.0 2.9 11.9 0.9

1.0 2.3 11.9 0.4

1.1 1.8 9.5 0.2

1.0 1.4 8.1 0.4

1.2 1.9 9.9 0.4

Computer/

Signal

1152 x 864

(75Hz)

1280 x 960

(60Hz)

1280 x 1024

(60Hz)

1280 x 1024

(75Hz)

1280 x 1024

(85Hz)

1600 x 1200

(60Hz)

Display interval (c)

Vertical signal timing (lines)

3 32 864 1

3 36 960 1

3 38 1024 1

3 37 1024 2

3 44 1024 1

3 46 1200 1

Page 65

Connection to the ports

Connection to the portsConnection to the ports

AUDIO IN1

CB/P

CR/P

COMPONENT VIDEO

RGB IN 1, BRGB IN 2, CRGB OUT

D-sub 15pin mini shrink jack

11 12 13 14 15

6 7 8 9 10

1 2 3 4 5

• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)

• H/V. sync. Signal: TTL level (positive/negative)

• Composite sync. Signal: TTL level

At RGB signal At component video signal

Pin Signal

Video Red 2 Video Green 3 Video Blue 4 (No connection) 5 Ground 6 Ground Red 7 Ground Green 8 Ground Blue 9 (No connection)

10 Ground

11 (No connection)

: SDA (DDC data),

H. sync / Composite sync.

V. sync.

: SCL (DDC clock),

AUDIO OUT

AUDIO IN2

VIDEO

S-VIDEO

USB

: (No connection)

RGB IN1

CONTROL

RGB IN2 RGB OUT

Pin Signal

CR/P

CB/P

(No connection)

Ground

CR/PR Ground

Y Ground

CB/PB Ground

(No connection)

Ground

(No connection)

* except for RGB OUT.

TECHNICAL

AUDIO IN1, EAUDIO IN2, FAUDIO OUT

φ3.5 stereo mini jack

• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminator (positive)

• H/V. sync. Signal: TTL level (positive/negative)

• Composite sync. Signal: TTL level

Page 66

Connection to the ports

Connection to the portsConnection to the ports

CB/P

CR/P

COMPONENT VIDEO

VIDEO

S-VIDEO

AUDIO IN1

AUDIO OUT

AUDIO IN2

RGB IN1

USB

CONTROL

RGB IN2 RGB OUT

COMPONENT VIDEO GY, HCB/PB, ICR/P

RCA jack x3

• System: 525i(480i), 525p(480p), 625i(576i), 750p(720p), 1125i(1080i)

Port Signal

Y Component video Y, 1.0±0.1Vp-p, 75Ω terminator with composite

/PBComponent video CB/PB, 0.7±0.1Vp-p, 75Ω terminator

R/PR

Component video CR/PR, 0.7±0.1Vp-p, 75Ω terminator

S-VIDEO

Mini DIN 4pin jack

Pin Signal

Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator

Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator Brightness signal, 1.0Vp-p, 75Ω terminator

Ground

VIDEO

RCA jack

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL60

• 1.0±0.1Vp-p, 75Ω terminator

Page 67

USB

USB B type jack

Pin Signal

1 +5V 2 - Data 3 + Data 4 Ground

CONTROL

D-sub 9pin plug

9 8 7 6

5 4 3 2 1

CB/P

CR/P

COMPONENT VIDEO

Connection to the ports

AUDIO IN1

VIDEO

S-VIDEO

AUDIO OUT

AUDIO IN2

RGB IN1

USB

CONTROL

L M

RGB IN2 RGB OUT

TECHNICAL

• About the details of RS-232C communication, please refer to the following page.

Pin Signal Pin Signal Pin Signal

1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection)

Page 68

RS-232C Communication

RS-232C CommunicationRS-232C Communication

123

CONTROL port RS-232C cable RS-232C port of the projector of the computer

RD (2) (2) RD TD (3) (3) TD

- (4) (4) DTR GND (5) (5) GND

- (6) (6) DSR RTS (7) (7) RTS CTS (8) (8) DTS

- (9) (9) RI

- (1) (1) CD

12345

789

Connecting the cable

Turn off the projector and the computer.

Connect the CONTROL port of the projector with a RS-232C port of the

computer by a RS-232C cable. Use the cable that fulfills the specification

shown in the previous page.

Turn the computer on, and after the computer has started up turn the

projector on.

Communications setting

19200bps, 8N1

1. Protocol

Consist of header (7 bytes) + command data (6 bytes).

2. Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low : Lower byte of CRC ﬂ ag for command data CRC_high : Upper byte of CRC ﬂ ag for command data

3. Command data

Command data chart

byte_0 byte_1 byte_2 byte_3 byte_4 byte_5

Action Type Setting code

low high low high low high

Action (byte_0 - 1)

Action Classiﬁ cation Content

1 SET Change setting to desired value. 2 GET Read projector internal setup value. 4 INCREMENT Increment setup value by 1. 5 DECREMENT Decrement setup value by 1. 6 EXECUTE Run a command.

Page 69

RS-232C Communication (continued)

Requesting projector status (Get command)

(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+

‘00H’ +‘00H’) from the computer to the projector.

(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.

Changing the projector settings (Set command)

(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +

setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.

Using the projector default settings (Reset Command)

(1) The computer sends the default setting code Header + Command data (‘06H’+

‘00H’ + type (2 bytes) +‘00H’+‘00H’) to the projector. (2) The projector changes the speciﬁ ed setting to the default value. (3) The projector returns the response code ‘06H’ to the computer.

Increasing the projector setting value (Increment command)

(1) The computer sends the increment code Header + Command data (‘04H’+

‘00H’+ type (2 bytes) +‘00H’+‘00H’) to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.

Decreasing the projector setting value (Decrement command)

(1) The computer sends the decrement code Header + Command data (‘05H’+

‘00H’+ type (2 bytes) +‘00H’ + ‘00H’) to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.

When the projector cannot understand the received command

When the projector cannot understand the received command, the error code ‘15H’ is sent back to the computer. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code ‘15H’ is sent back to the computer. If this error code is returned, send the same command again.

When the projector cannot execute the received command.

When the projector cannot execute the received command, the error code ‘1cH’ + ‘xxxxH’ is sent back to the computer. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the computer.

TECHNICAL

NOTE • Operation cannot be guaranteed when the projector receives an undeﬁ ned

command or data.

• Provide an interval of at least 40ms between the response code and any other code.

• The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data.

• Commands are not accepted during warm-up.

Page 70

RS-232C Communication (continued)

Names Operation Type Header

Power Set Turn off BE EF 03 06 00 2A D3 01 00 00 60 00 00

Turn on BE EF 03 06 00 BA D2 01 00 00 60 01 00

Get BE EF 03 06 00 19 D3 02 00 00 60 00 00

(Example return) 00 00 01 00 02 00

Input Source Set RGB IN1 BE EF 03 06 00 FE D2 01 00 00 20 00 00

RGB IN2 BE EF 03 06 00 3E D0 01 00 00 20 04 00

VIDEO BE EF 03 06 00 6E D3 01 00 00 20 01 00

S-VIDEO BE EF 03 06 00 9E D3 01 00 00 20 02 00

COMPONENT BE EF 03 06 00 AE D1 01 00 00 20 05 00

Get BE EF 03 06 00 CD D2 02 00 00 20 00 00

Error Status Get BE EF 03 06 00 D9 D8 02 00 20 60 00 00

BRIGHT Get BE EF 03 06 00 89 D2 02 00 03 20 00 00

Increment BE EF 03 06 00 EF D2 04 00 03 20 00 00

Decrement BE EF 03 06 00 3E D3 05 00 03 20 00 00

BRIGHT Reset Execute BE EF 03 06 00 58 D3 06 00 00 70 00 00

CONTRAST Get BE EF 03 06 00 FD D3 02 00 04 20 00 00

Increment BE EF 03 06 00 9B D3 04 00 04 20 00 00

Decrement BE EF 03 06 00 4A D2 05 00 04 20 00 00

CONTRAST Reset Execute BE EF 03 06 00 A4 D2 06 00 01 70 00 00

MODE Set NORMAL BE EF 03 06 00 23 F6 01 00 BA 30 00 00

CINEMA BE EF 03 06 00 B3 F7 01 00 BA 30 01 00 DYNAMIC BE EF 03 06 00 E3 F4 01 00 BA 30 04 00 Get BE EF 03 06 00 10 F6 02 00 BA 30 00 00

GAMMA Set #1 DEFAULT BE EF 03 06 00 07 E9 01 00 A1 30 20 00

#1 CUSTOM BE EF 03 06 00 07 FD 01 00 A1 30 10 00

#2 DEFAULT BE EF 03 06 00 97 E8 01 00 A1 30 21 00

#2 CUSTOM BE EF 03 06 00 97 FC 01 00 A1 30 11 00

#3 DEFAULT BE EF 03 06 00 67 E8 01 00 A1 30 22 00

#3 CUSTOM BE EF 03 06 00 67 FC 01 00 A1 30 12 00

Get BE EF 03 06 00 F4 F0 02 00 A1 30 00 00

(Off) (On) (Cool down)

(Example return) 00 00 01 00 02 00 03 00 (Normal) (Cover error) (Fan error) (Lamp error) 04 00 05 00 06 00 07 00 (Temp error) (Air ﬂ ow error) (Lamp time error) (Cool error) 08 00 (Filter error) (Filter missing error) (Inner Sencer error)

(Example return) 00 00 01 00 04 00 10 00 (Normal) (Cinema) (Dynamic) (Custom)

CRC Action Type Setting Code

09 00 10 00

Command Data

Page 71

RS-232C Communication (continued)

Names Operation Type Header

User Gamma Pattern Set Off BE EF 03 06 00 FB FA 01 00 80 30 00 00

9 step gray scale BE EF 03 06 00 6B FB 01 00 80 30 01 00

15 steps gray scale BE EF 03 06 00 9B FB 01 00 80 30 02 00

Ramp BE EF 03 06 00 0B FA 01 00 80 30 03 00

Get BE EF 03 06 00 C8 FA 02 00 80 30 00 00

User Gamma Point 1 Get BE EF 03 06 00 08 FE 02 00 90 30 00 00

Increment BE EF 03 06 00 6E FE 04 00 90 30 00 00

Decrement BE EF 03 06 00 BF FF 05 00 90 30 00 00

User Gamma Point 2 Get BE EF 03 06 00 F4 FF 02 00 91 30 00 00

Increment BE EF 03 06 00 92 FF 04 00 91 30 00 00

Decrement BE EF 03 06 00 43 FE 05 00 91 30 00 00

User Gamma Point 3 Get BE EF 03 06 00 B0 FF 02 00 92 30 00 00

Increment BE EF 03 06 00 D6 FF 04 00 92 30 00 00

Decrement BE EF 03 06 00 07 FE 05 00 92 30 00 00

User Gamma Point 4 Get BE EF 03 06 00 4C FE 02 00 93 30 00 00

Increment BE EF 03 06 00 2A FE 04 00 93 30 00 00

Decrement BE EF 03 06 00 FB FF 05 00 93 30 00 00

User Gamma Point 5 Get BE EF 03 06 00 38 FF 02 00 94 30 00 00

Increment BE EF 03 06 00 5E FF 04 00 94 30 00 00

Decrement BE EF 03 06 00 8F FE 05 00 94 30 00 00

User Gamma Point 6 Get BE EF 03 06 00 C4 FE 02 00 95 30 00 00

Increment BE EF 03 06 00 A2 FE 04 00 95 30 00 00

Decrement BE EF 03 06 00 73 FF 05 00 95 30 00 00

User Gamma Point 7 Get BE EF 03 06 00 80 FE 02 00 96 30 00 00

Increment BE EF 03 06 00 E6 FE 04 00 96 30 00 00

Decrement BE EF 03 06 00 37 FF 05 00 96 30 00 00

User Gamma Point 8 Get BE EF 03 06 00 7C FF 02 00 97 30 00 00

Increment BE EF 03 06 00 1A FF 04 00 97 30 00 00

Decrement BE EF 03 06 00 CB FE 05 00 97 30 00 00

COLOR TEMP Set LOW BE EF 03 06 00 6B F4 01 00 B0 30 01 00

MIDDLE BE EF 03 06 00 9B F4 01 00 B0 30 02 00

HIGH BE EF 03 06 00 0B F5 01 00 B0 30 03 00 CUSTOM BE EF 03 06 00 3B F8 01 00 B0 30 10 00 Get BE EF 03 06 00 C8 F5 02 00 B0 30 00 00

COLOR TEMP GAIN R Get BE EF 03 06 00 34 F4 02 00 B1 30 00 00

Increment BE EF 03 06 00 52 F4 04 00 B1 30 00 00

Decrement BE EF 03 06 00 83 F5 05 00 B1 30 00 00

CRC Action Type Setting Code

Command Data

TECHNICAL

Page 72

RS-232C Communication (continued)

Names Operation Type Header

COLOR TEMP GAIN G Get BE EF 03 06 00 70 F4 02 00 B2 30 00 00

Increment BE EF 03 06 00 16 F4 04 00 B2 30 00 00

Decrement BE EF 03 06 00 C7 F5 05 00 B2 30 00 00

COLOR TEMP GAIN B Get BE EF 03 06 00 8C F5 02 00 B3 30 00 00

Increment BE EF 03 06 00 EA F5 04 00 B3 30 00 00

Decrement BE EF 03 06 00 3B F4 05 00 B3 30 00 00

COLOR TEMP

OFFSET R

COLOR TEMP

OFFSET G

COLOR TEMP

OFFSET B

COLOR Get BE EF 03 06 00 B5 72 02 00 02 22 00 00

COLOR Reset Execute BE EF 03 06 00 80 D0 06 00 0A 70 00 00

TINT Get BE EF 03 06 00 49 73 02 00 03 22 00 00

TINT Reset Execute BE EF 03 06 00 7C D1 06 00 0B 70 00 00

SHARPNESS Get BE EF 03 06 00 F1 72 02 00 01 22 00 00

SHARPNESS Reset Execute BE EF 03 06 00 C4 D0 06 00 09 70 00 00

PROGRESSIVE Set TURN OFF BE EF 03 06 00 4A 72 01 00 07 22 00 00

MY MEMORY Load Set 1 BE EF 03 06 00 0E D7 01 00 14 20 00 00

MY MEMORY Save Set 1 BE EF 03 06 00 F2 D6 01 00 15 20 00 00

ASPECT Set 4:3 BE EF 03 06 00 9E D0 01 00 08 20 00 00

Get BE EF 03 06 00 04 F5 02 00 B5 30 00 00

Increment BE EF 03 06 00 62 F5 04 00 B5 30 00 00

Decrement BE EF 03 06 00 B3 F4 05 00 B5 30 00 00

Get BE EF 03 06 00 40 F5 02 00 B6 30 00 00

Increment BE EF 03 06 00 26 F5 04 00 B6 30 00 00

Decrement BE EF 03 06 00 F7 F4 05 00 B6 30 00 00

Get BE EF 03 06 00 BC F4 02 00 B7 30 00 00

Increment BE EF 03 06 00 DA F4 04 00 B7 30 00 00

Decrement BE EF 03 06 00 0B F5 05 00 B7 30 00 00

Increment BE EF 03 06 00 D3 72 04 00 02 22 00 00

Decrement BE EF 03 06 00 02 73 05 00 02 22 00 00

Increment BE EF 03 06 00 2F 73 04 00 03 22 00 00

Decrement BE EF 03 06 00 FE 72 05 00 03 22 00 00

Increment BE EF 03 06 00 97 72 04 00 01 22 00 00

Decrement BE EF 03 06 00 46 73 05 00 01 22 00 00

TV BE EF 03 06 00 DA 73 01 00 07 22 01 00

FILM BE EF 03 06 00 2A 73 01 00 07 22 02 00

Get BE EF 03 06 00 79 72 02 00 07 22 00 00

2 BE EF 03 06 00 9E D6 01 00 14 20 01 00 3 BE EF 03 06 00 6E D6 01 00 14 20 02 00 4 BE EF 03 06 00 FE D7 01 00 14 20 03 00

2 BE EF 03 06 00 62 D7 01 00 15 20 01 00 3 BE EF 03 06 00 92 D7 01 00 15 20 02 00 4 BE EF 03 06 00 02 D6 01 00 15 20 03 00

16:9 BE EF 03 06 00 0E D1 01 00 08 20 01 00

SMALL BE EF 03 06 00 FE D1 01 00 08 20 02 00 NORMAL BE EF 03 06 00 5E DD 01 00 08 20 10 00 Get BE EF 03 06 00 AD D0 02 00 08 20 00 00

CRC Action Type Setting Code

Command Data

Page 73

RS-232C Communication (continued)

Names Operation Type Header

OVER SCAN Get BE EF 03 06 00 91 70 02 00 09 22 00 00

Increment BE EF 03 06 00 F7 70 04 00 09 22 00 00

Decrement BE EF 03 06 00 26 71 05 00 09 22 00 00

OVER SCAN Reset Execute BE EF 03 06 00 EC D9 06 00 27 70 00 00

V POSITION Get BE EF 03 06 00 0D 83 02 00 00 21 00 00

Increment BE EF 03 06 00 6B 83 04 00 00 21 00 00

Decrement BE EF 03 06 00 BA 82 05 00 00 21 00 00

V POSITION Reset Execute BE EF 03 06 00 E0 D2 06 00 02 70 00 00

H POSITION Get BE EF 03 06 00 F1 82 02 00 01 21 00 00

Increment BE EF 03 06 00 97 82 04 00 01 21 00 00

Decrement BE EF 03 06 00 46 83 05 00 01 21 00 00

H POSITION Reset Execute BE EF 03 06 00 1C D3 06 00 03 70 00 00

H PHASE Get BE EF 03 06 00 49 83 02 00 03 21 00 00

Increment BE EF 03 06 00 2F 83 04 00 03 21 00 00

Decrement BE EF 03 06 00 FE 82 05 00 03 21 00 00

H SIZE Get BE EF 03 06 00 B5 82 02 00 02 21 00 00

Increment BE EF 03 06 00 D3 82 04 00 02 21 00 00

Decrement BE EF 03 06 00 02 83 05 00 02 21 00 00

H SIZE Reset Execute BE EF 03 06 00 68 D2 06 00 04 70 00 00

AUTO ADJUST Execute BE EF 03 06 00 91 D0 06 00 0A 20 00 00

COLOR SPACE Set AUTO BE EF 03 06 00 0E 72 01 00 04 22 00 00

RGB BE EF 03 06 00 9E 73 01 00 04 22 01 00

SMPTE240 BE EF 03 06 00 6E 73 01 00 04 22 02 00

REC709 BE EF 03 06 00 FE 72 01 00 04 22 03 00 REC601 BE EF 03 06 00 CE 70 01 00 04 22 04 00

Get BE EF 03 06 00 3D 72 02 00 04 22 00 00

COMPONENT Set COMPONENT BE EF 03 06 00 4A D7 01 00 17 20 00 00

SCART RGB BE EF 03 06 00 DA D6 01 00 17 20 01 00

Get BE EF 03 06 00 79 D7 02 00 17 20 00 00

VIDEO FORMAT Set AUTO BE EF 03 06 00 9E 75 01 00 00 22 0A 00

NTSC BE EF 03 06 00 FE 71 01 00 00 22 04 00

PAL BE EF 03 06 00 6E 70 01 00 00 22 05 00

SECAM BE EF 03 06 00 6E 75 01 00 00 22 09 00

NTSC4.43 BE EF 03 06 00 5E 72 01 00 00 22 02 00

M-PAL BE EF 03 06 00 FE 74 01 00 00 22 08 00

N-PAL BE EF 03 06 00 0E 71 01 00 00 22 07 00

Get BE EF 03 06 00 0D 73 02 00 00 22 00 00

CRC Action Type Setting Code

Command Data

TECHNICAL

Page 74

RS-232C Communication (continued)

Names Operation Type Header

FRAME LOCK Set TURN OFF BE EF 03 06 00 CB D6 01 00 14 30 00 00

TURN ON BE EF 03 06 00 5B D7 01 00 14 30 01 00 Get BE EF 03 06 00 F8 D6 02 00 14 30 00 00

KEYSTONE V Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00

Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00

Decrement BE EF 03 06 00 0E D2 05 00 07 20 00 00

KEYSTONE V Reset Execute BE EF 03 06 00 08 D0 06 00 0C 70 00 00

WHISPER Set NORMAL BE EF 03 06 00 3B 23 01 00 00 33 00 00

WHISPER BE EF 03 06 00 AB 22 01 00 00 33 01 00 Get BE EF 03 06 00 08 23 02 00 00 33 00 00

MIRROR Set NORMAL BE EF 03 06 00 C7 D2 01 00 01 30 00 00

H:INVERT BE EF 03 06 00 57 D3 01 00 01 30 01 00 V:INVERT BE EF 03 06 00 A7 D3 01 00 01 30 02 00

H&V:INVERT BE EF 03 06 00 37 D2 01 00 01 30 03 00

Get BE EF 03 06 00 F4 D2 02 00 01 30 00 00

VOLUME Get BE EF 03 06 00 31 D3 02 00 01 20 00 00

Increment BE EF 03 06 00 57 D3 04 00 01 20 00 00

Decrement BE EF 03 06 00 86 D2 05 00 01 20 00 00

MUTE Set TURN OFF BE EF 03 06 00 46 D3 01 00 02 20 00 00

TURN ON BE EF 03 06 00 D6 D2 01 00 02 20 01 00 Get BE EF 03 06 00 75 D3 02 00 02 20 00 00

LANGUAGE Set ENGLISH BE EF 03 06 00 F7 D3 01 00 05 30 00 00

FRANÇAIS BE EF 03 06 00 67 D2 01 00 05 30 01 00

DEUTSCH BE EF 03 06 00 97 D2 01 00 05 30 02 00

ESPAÑOL BE EF 03 06 00 07 D3 01 00 05 30 03 00 ITALIANO BE EF 03 06 00 37 D1 01 00 05 30 04 00

NORSK BE EF 03 06 00 A7 D0 01 00 05 30 05 00

NEDERLANDS BE EF 03 06 00 57 D0 01 00 05 30 06 00

PORTUGUÊS BE EF 03 06 00 C7 D1 01 00 05 30 07 00

BE EF 03 06 00 37 D4 01 00 05 30 08 00 BE EF 03 06 00 A7 D5 01 00 05 30 09 00

BE EF 03 06 00 57 D5 01 00 05 30 0A 00 SVENSKA BE EF 03 06 00 C7 D4 01 00 05 30 0B 00 PУCCKИЙ BE EF 03 06 00 F7 D6 01 00 05 30 0C 00

SUOMI BE EF 03 06 00 67 D7 01 00 05 30 0D 00

POLSKI BE EF 03 06 00 97 D7 01 00 05 30 0E 00

Get BE EF 03 06 00 C4 D3 02 00 05 30 00 00

CRC Action Type Setting Code

Command Data

Page 75

RS-232C Communication (continued)

Names Operation Type Header

MENU POSITION H Get BE EF 03 06 00 04 D7 02 00 15 30 00 00

Increment BE EF 03 06 00 62 D7 04 00 15 30 00 00

Decrement BE EF 03 06 00 B3 D6 05 00 15 30 00 00

MENU POSITION H

Reset

MENU POSITION V Get BE EF 03 06 00 40 D7 02 00 16 30 00 00

MENU POSITION V

Reset

OSD BRIGHT Get BE EF 03 06 00 A8 D5 02 00 18 30 00 00

BLANK Set My Screen BE EF 03 06 00 FB CA 01 00 00 30 20 00

BLANK On/Off Set TURN OFF BE EF 03 06 00 FB D8 01 00 20 30 00 00

START UP Set My Screen BE EF 03 06 00 CB CB 01 00 04 30 20 00

My Screen LOCK Set TURN OFF BE EF 03 06 00 3B EF 01 00 C0 30 00 00

Message Set TURN OFF BE EF 03 06 00 8F D6 01 00 17 30 00 00

AUTO SEARCH Set TURN OFF BE EF 03 06 00 B6 D6 01 00 16 20 00 00

AUTO POWER OFF Get BE EF 03 06 00 08 86 02 00 10 31 00 00

Execute BE EF 03 06 00 DC C6 06 00 43 70 00 00

Increment BE EF 03 06 00 26 D7 04 00 16 30 00 00

Decrement BE EF 03 06 00 F7 D6 05 00 16 30 00 00

Execute BE EF 03 06 00 A8 C7 06 00 44 70 00 00

Increment BE EF 03 06 00 CE D5 04 00 18 30 00 00

Decrement BE EF 03 06 00 1F D4 05 00 18 30 00 00

ORIGINAL BE EF 03 06 00 FB E2 01 00 00 30 40 00

BLUE BE EF 03 06 00 CB D3 01 00 00 30 03 00 WHITE BE EF 03 06 00 6B D0 01 00 00 30 05 00 BLACK BE EF 03 06 00 9B D0 01 00 00 30 06 00

Get BE EF 03 06 00 08 D3 02 00 00 30 00 00

TURN ON BE EF 03 06 00 6B D9 01 00 20 30 01 00 Get BE EF 03 06 00 C8 D8 02 00 20 30 00 00

ORIGINAL BE EF 03 06 00 0B D2 01 00 04 30 00 00

TURN OFF BE EF 03 06 00 9B D3 01 00 04 30 01 00

Get BE EF 03 06 00 38 D2 02 00 04 30 00 00

TURN ON BE EF 03 06 00 AB EE 01 00 C0 30 01 00 Get BE EF 03 06 00 08 EF 02 00 C0 30 00 00

TURN ON BE EF 03 06 00 1F D7 01 00 17 30 01 00 Get BE EF 03 06 00 BC D6 02 00 17 30 00 00

TURN ON BE EF 03 06 00 26 D7 01 00 16 20 01 00 Get BE EF 03 06 00 85 D6 02 00 16 20 00 00

Increment BE EF 03 06 00 6E 86 04 00 10 31 00 00

Decrement BE EF 03 06 00 BF 87 05 00 10 31 00 00

CRC Action Type Setting Code

Command Data

TECHNICAL

Page 76

RS-232C Communication (continued)

Names Operation Type Header

LAMP TIME Get BE EF 03 06 00 C2 FF 02 00 90 10 00 00

LAMP TIME Reset Execute BE EF 03 06 00 58 DC 06 00 30 70 00 00

FILTER TIME Get BE EF 03 06 00 C2 F0 02 00 A0 10 00 00

FILER TIME Reset Execute BE EF 03 06 00 98 C6 06 00 40 70 00 00

MAGNIFY Get BE EF 03 06 00 7C D2 02 00 07 30 00 00

Increment BE EF 03 06 00 1A D2 04 00 07 30 00 00

Decrement BE EF 03 06 00 CB D3 05 00 07 30 00 00

FREEZE Set NORMAL BE EF 03 06 00 83 D2 01 00 02 30 00 00

FREEZE BE EF 03 06 00 13 D3 01 00 02 30 01 00

Get BE EF 03 06 00 B0 D2 02 00 02 30 00 00

CRC Action Type Setting Code

Command Data

Page 77

Page 78

Dukane Corporation Audio Visual Products Division 2900 Dukane Drive St. Charles, IL 60174-3395 E-mail: avsales@dukcorp.com

Audio Visual Products

Phone: (630) 762-4040

Orders: (800) 676-2485

Information: (800) 676-2486

Fax: (630) 584-5156

Parts & Service: (800) 676-2487

Fax: (630) 584-0984

Part # 401-8063/8755C-00