Dukane 8755 User Manual

LIQUID CRYSTAL PROJECTOR

28A8049A/8755

USER'S MANUAL

LCD Projector 28A8049A/8755

USER'S MANUAL Vol.1 (Basic)

USER'S MANUAL

Thank you for purchasing this projector.

WARNING • Please read the accompanying manual “SAFETY

INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.

ENGLISH

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in this manual

• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.

TRADEMARK ACKNOWLEDGEMENT :

• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.

• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

• All other trademarks are the property of their respective owners.

• The information in this manual is subject to change without notice.

CONTENTS

Page

PROJECTOR FEATURES................2

PREPARATIONS ..............................2

PART NAMES...................................4

SETTING UP

THE PROJECTOR ............................6

CONNECTING

YOUR DEVICES................................8

USING THE REMOTE

CONTROL.......................................13

TURNING ON THE POWER ...........14

TURNING OFF THE POWER .........16

ADJUSTING THE VOLUME ...........17

TEMPORARILY MUTING

THE SOUND....................................17

ADJUSTING THE POSITION..........18

USING THE AUTOMATIC

ADJUSTMENT FEATURE ..............19

CORRECTING KEYSTONE

DISTORTIONS ................................20

USING THE MAGNIFY

FEATURE........................................21

FREEZING THE SCREEN ..............21

SIGNAL SEARCHING.....................22

SELECTING THE ASPECT

RATIO..............................................22

TEMPORARILY BLANKING

THE SCREEN..................................22

USING THE MENU

FUNCTIONS....................................23

OPERATING THE PC SCREEN .....24

THE LAMP ......................................25

THE AIR FILTER.............................27

OTHER CARE.................................29

REGULATORY NOTICES...............30

Page

1

PROJECTOR

FEATURES

This liquid crystal projector is used to project
various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space
is required for installation and large images can
easily be realized.

Ultra High Brightness

●

Crisp, ultra-bright presentations is achieved
by using a UHB (ultra high brightness) lamp
and a highly efficient optical system

Partial Magnification Function

●

Interesting parts of images can be magnified
for closer viewing

PREPARATIONS

Your projector should come with the items
shown below. Check to make sure that all the
items are included. Contact your dealer if
anything is missing.

NOTE

• Keep the original packing material for future reshipment.

RESET

KEYSTONE

POWER

INPUT

TENP

STANDBY/ON

LANP

Power cord

(US Type)

Projector

(with Lens Cap)

Liquid Crystal Projector

CP-S317/CP-X327

(CP-S317W/CP-X327W)

USER'S MANUALVol.1 Basic

Please read this user's manual thoroughly to ensure correct usage through understanding.

BEDIENUNGSANLEITUNG Teil 1 Grundlagen

Bitte lessen Sie diese Benutzerhandbuch zugunsten der korrekten Bedienung aufmerksam.

MANUEL D'UTILISATION Vol.1 Fondements

Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le fonctionnement de l'appareil.

MANUALE D'ISTRUZIONI Vol.1 Informazioni di base

Vi preghiamo voler leggere attentamente il manuale d'istruzioni in modo tale da poter comprendere quanto riportato
ai fini di un corretto utilizzo del proiettore.

MANUAL DE USUARIO Vol.1 Básico

Lea cuidadosamente este manual del usuario para poder utilizar corretamente el producto.

GEBRUIKSAANWIJZING Vol.1 Basis

Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te hebben van de
uitgebreide mogelijkheden.

BRUKERHÅNDBOK Vol.1 Grunnleggende

Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.

NSTRUÇÕES DO PROPRIETÁRIO Vol.1 Básico

Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do utilizador.

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

T

E
S
E
R
E
N
O

T
S
Y
E

ER

K

W
O
P

T
U
P
N
I

P
N

N
O

/

TE

Y

B
D
N
A
T
S

P
N
LA

NORSK

PORTGÊS

RGB cable USB mouse

Keystone Distortion Correction

●

Quick correction of distorted images electrically

Whisper Mode Equipped

●

Special mode is available for reducing
projector noise to achieve quieter operation

Power cord

(UK Type)

Power cord

(Europe Type)

Video/Audio cable

cable

User's Manuals

(Vol.1/Vol.2)

Safety Instructions

Soft carrying case

2

Two AA batteries

(for the remote

control)

STANDBY/ON

VIDEO

RGB SEARCH

ASPECT

AUTO BLANK

HOME

PAGE UP VOLUME

MAGNIFY

ON

END

PAGE DOWN

MUTE

OFF

KEYSTONEFREEZE

MENUPOSITION

ENTER

ESC RESET

Remote control

WARNING Precautions to observe in regards to the power cord: Please use extra

caution when connecting the projector's power cord as incorrect or faulty
connections may result in FIRE AND/OR ELECTRICAL SHOCK. Please adhere to the
following safety guidelines to insure safe operation of the projector:

•

Only plug the power cord into outlets rated for use with the power cord's specified voltage range.

• Only use the power cord that came with the projector.

• NEVER ATTEMPT TO DEFEAT THE GROUND CONNECTION OF THE THREE-

PRONGED PLUG!

• Make sure that you firmly connect the power cord to the projector and wall outlet.

ENGLISH

Connect your devices to the projector

1

Connect your computer, VCR and/or other
devices you will be using to the projector.

Insert the batteries into the remote

2

control

Connect the power cord

3

(1)

Connect the connector of the electrical power cord to the AC inlet of the main unit.

(2) Firmly plug the power cord's plug into the outlet

8 12

〜

13

Power outlet

(1)

(2)

Power cordAC inlet

3

PART NAMES

MENU button

23

RESET button

24

THE PROJECTOR

Indicates the corresponding
reference page

POWER indicator

TEMP indicator

LAMP indicator

Lens cap

10

14

AUDIO IN R and L ports

VIDEO IN port

11

26

14

27

Remote sensor

KEYSTONE button

20

INPUT button

15

STANDBY/ON button

14

RESET

KEYSTONE

POWER

TENP

LANP

INPUT

BY/ON

STAND

Air filter

27

Elevator button

6

15

15

Zoom ring

Focus ring

13

S-VIDEO IN port

11

RGB IN 1 and 2 ports

10

AC power inlet

3

STANDBY/ON

12

USB port

10

COMPONENT VIDEO port

11

INPUT

KEYSTONE

RGB OUT port

RESET

10

LANP

TENP

PO

W

ER

CONTROL port

6

Power switch

14

Elevator button

4

THE REMOTE CONTROL

RGB button

VIDEO button

ASPECT button

MAGNIFY buttons

FREEZE button

15

VIDEO

15

ASPECT

22

MAGNIFY

ON

21

OFF

21

RGB SEARCH

AUTO BLANK

HOME

PAGE UP VOLUME

END

PAGE DOWN

STANDBY/ON

MUTE

KEYSTONEFREEZE

SEARCH button

22

STANDBY/ON button

14

AUTO button

19

BLANK button

22

VOLUME button

17

MUTE button

17

KEYSTONE button

20

ENGLISH

KEYBOARD buttons

POSITION button

,,,
Cursor buttons

ESC button

24

18

23

23

MENUPOSITION

ENTER

ESC RESET

MENU button

23

RESET button

24

ENTER button

23

5

SETTING UP THE PROJECTOR

CAUTION •

of the accompanying manual “SAFETY INSTRUCTIONS” and this manual.

• If you press the elevator buttons without holding the projector, the projector might

crash down, overturn, smash your fingers and possibly result in malfunction. To
prevent damaging the projector and injuring yourself, ALWAYS HOLD THE
PROJECTOR whenever using the elevator buttons to adjust the elevator feet.

Install the projector in a suitable environment according to instructions

Adjusting the Projector's Elevator Feet

You can use the elevator feet to make adjustments if the surface on which you
need to set the projector is uneven or if you otherwise need to adjust the angle of
projection. The adjustment range of the elevator feet is 0 to 9 degrees.

Press and hold in the elevator

1

buttons

Raise or lower the projector to the

2

desired height and then release the
elevator buttons

When you release the elevator buttons, the elevator
feet will lock into position.

As necessary, you can also finely

3

adjust the height of the projector by
twisting the elevator feet by hand

6

Adjusting the Screen Size and Projection Distance

Refer to the illustrations and tables below to determine the screen size and
projection distance.

The values shown in the table are calculated for a full size screen

a:Distance from the projector to the screen (±10%)
b:Distance from the lens center to the bottom of the screen (±10%)
c:Distance from the lens center to the top of the screen (±10%)

The screen

Top view

If 4:3 aspect ratio

4

3

ENGLISH

Lens center

c

b

The screen

c

Lens center

b

Screen Size [inch (m)]

30 (0.8) 35 (0.9) 42 (1.1) 1 (2) 17 (44)
40 (1.0) 47 (1.2) 56 (1.4) 1 (3) 23 (58)
50 (1.3) 59 (1.5) 71 (1.8) 1 (4) 29 (73)
60 (1.5) 71 (1.8) 85 (2.2) 2 (4) 34 (87)
70 (1.8) 83 (2.1)
80 (2.0) 95 (2.4)
90 (2.3)

100 (2.5)

Side view

a

Top view

Side view

a

120 (3.0)
150 (3.8)
200 (5.0)
250 (6.3)
300 (7.5)

If 16:9 aspect ratio

9

Screen Size [inch (m)]

30 (0.8) 38 (1.0) 46 (1.2) 2 (4) 16 (41)
40 (1.0) 51 (1.3) 61 (1.6) 2 (5) 22 (55)
50 (1.3) 64 (1.6) 77 (2.0) 3 (6) 27 (69)
60 (1.5) 77 (2.0) 93 (2.4) 3 (8) 32 (82)
70 (1.8) 90 (2.3)
80 (2.0)

90 (2.3)
100 (2.5)
120 (3.0)
150 (3.8)
200 (5.0)
250 (6.3)
300 (7.5)

a [inch (m)]

Min. Max.

107 (2.7) 129 (3.3)
119 (3.0) 143 (3.6)
143 (3.6) 172 (4.4)
180 (4.6) 216 (5.5)
240 (6.1) 288 (7.3)
300 (7.6) 361 (9.2)
360 (9.2)

16

a [inch (m)]

Min. Max.

104 (2.6) 125 (3.2)
117 (3.0) 140 (3.6)
130 (3.3) 156 (4.0)
156 (4.0) 188 (4.8)
196 (5.0) 235 (6.0)
261 (6.6) 314 (8.0)
327 (8.3)
393 (10.0)

100 (2.5)
114 (2.9)

433 (11.0)

109 (2.8)

393 (10.0)
472 (12.0)

b

[inch (cm)]c [inch (cm)]

2 (5) 40 (102)
2 (6) 46 (116)
3 (7) 51 (131)
3 (7) 57 (145)
3 (9) 69 (174)
4 (11) 86 (218)
6 (15)

114 (290)

7 (18)

143 (363)

9 (22)

171 (435)

b

[inch (cm)]c [inch (cm)]

4 (9) 38 (96)
4 (10) 43 (110)
5 (12) 49 (124)
5 (13) 54 (137)
6 (15) 65 (165)
8 (19) 81 (206)

10 (26)

108 (275)

13 (32)

135 (343)

15 (39)

162 (412)

7

CONNECTING YOUR DEVICES

Devices You Can Connect to the Projector
(Refer to this section for planning your device
configuration to use for your presentation.)

CAUTION • Incorrect connecting could result in fire or electrical shock. Please
read this manual and the separate “SAFETY INSTRUCTIONS”.

ATTENTION

• Whenever attempting to connect other devices to the projector, please thoroughly
read the manual of each device to be connected.

• TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to
connect a live device to the projector may generate extremely loud noises or other
abnormalities that may result in malfunction and/or damage to the device and/or
projector. Refer to the “TECHNICAL” of the USER’S MANUAL (Vol.2) for the pin
assignment of connectors and RS-232C communication data.

• Make sure that you connect devices to the correct port. Incorrect connection may
result in malfunction and/or damage to the device and/or projector.

• A component cable and some other cables have to be used with core set. Use the
accessory cable or a designated-type cable for the connection. For cables that have
a core only at one end, connect the core to the projector.

• Secure the screws on the connectors and tighten.

Precautions to observe when connecting other devices to the projector

Indicates the
corresponding
reference page

Display monitors

12

DVD players

11

Laptop computers

10

VCRs

11

Desktop computers

10

8

Ports and Cables

Refer to the table below to find out which projector port and cable to use for connecting a
given device. Use this table for determining which cables to prepare.

Function Projector Port Connection Cables

RGB input

RGB output RGB OUT

USB mouse control USB Accessory USB cable

PS/2 mouse control

ADB mouse control Optional ADB mouse cable

Serial mouse control Optional serial mouse cable

RS-232C communication Optional RS-232C cable

S-video input S-VIDEO IN

Video input VIDEO IN Accessory audio/video cable

Component video input

Audio input

NOTE

About Plug-and-Play Capability

RGB IN 1

RGB IN 2

CONTROL

COMPONENT VIDEO Y

COMPONENT VIDEO CR/P

AUDIO IN L

AUDIO IN R

B

R

Accessory RGB cable or optional RGB
cable with D-sub 15-pin shrink jack and
inch thread screws

Optional PS/2 mouse cable

Optional S-video cable with mini DIN 4-pin
jack

Optional component video cableCOMPONENT VIDEO CB/P

Accessory audio/video cable or optional
audio cable with RCA jack

• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by
connecting this projector to computers that are VESA DDC (display data channel)
compatible. Please take advantage of this function by connecting the accessory RGB
cable to the RGB IN 1 port (DDC 1/2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.

• Plug-and-Play is a system composed of the computer, its operating system and
peripheral equipment (i.e. display devices).

• Please use the standard drivers as this projector is a Plug-and-Play monitor.

• Plug-and-Play may not function properly with some type of computers. Use the RGB

IN 2 port if Plug-and-Play does not function correctly.

ENGLISH

9

B

A

AUDIO IN

COMPONENT VIIDEO

R L / (MONO) VIDEO IN

C

R / RR CB / PB Y

K

S-VIDEO IN

USB

1 RGB IN 2

RGB OUT CONTROL

A

BB

AUDIO IN

AUDIO cable

RGB cable

AUDIO OUT

RGB IN

Analogue

RGB OUT

CONNECTING YOUR DEVICES (continued)

Connecting to a Computer

ATTENTION Whenever attempting to connect a laptop computer to the projector,
be sure to activate the laptop's RGB external image output (set the laptop to CRT
display or to simultaneous LCD and CRT display). For details on how this is done,
please refer to the instruction manual of the corresponding laptop computer.

K

Laptop computer

AUDIO IN

R L / (MONO) VIDEO IN

R / RR CB / PB Y

C

COMPONENT VIIDEO

D

USB IN

USB cable

If connecting to a
USB port equipped
computer

USB OUT

S-VIDEO IN

CC

D

RGB OUT CONTROL

USB

AUDIO IN

AUDIO cable

AUDIO OUT

A

C

Desktop computer

NOTE

• Some computers may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.

• For some RGB input modes, the optional Mac adapter is necessary.

1 RGB IN 2

A

RGB IN

RGB cable

Analogue

RGB OUT

B

B

CONTROL IN CONTROL OUT

MOUSE cable

10