Dukane 6660WUSSB, 6652WUSSB, 6652WSSB User Manual
Projector
6652WSSB/6652WUSSB/
6660WUSSB
User’s Manual
Please visit our web site for User’s Manual in the latest version.
http://www.dukaneav.com
Model No.
6652WSSB/6652WUSSB/6660WUSSB
6652WSSB_6652WUSSB_6660WUSSB_User Manual-00
Table of Contents
Introduction .............................................................................................................................................. iii
Important Information ....................................................................................................................... iv
1. Check the product overview, supplied items and part names .................................... 1
1-1. Introduction to the Projector ............................................................................................................ 1
1-2. What’s in the Box? ................................................................................................................................. 4
1-3. Part Names of the Projector .............................................................................................................. 5
1-4. Part Names of the Remote Control .............................................................................................. 10
2. Projecting an Image (Basic Operation) ................................................................................. 15
2-1. Flow of Projecting an Image .......................................................................................................... 15
2-2. Connecting Your Computer/Connecting the Power Cord .................................................. 16
2-3. Turning on the Projector ................................................................................................................. 18
2-4. Selecting a Source ............................................................................................................................. 20
2-5. Adjusting the Picture Size and Position ..................................................................................... 22
2-6. Correcting Keystone Distortion [KEYSTONE] ........................................................................... 28
2-7. Optimizing Computer Signal Automatically ............................................................................ 32
2-8. Turning Up or Down Volume ......................................................................................................... 32
2-9. Turning off the Projector ................................................................................................................. 33
2-10. When Moving the Projector ......................................................................................................... 34
3. Convenient Features ....................................................................................................................... 35
3-1. Turning off the Image and Sound ................................................................................................ 35
3-2. Freezing a Picture ............................................................................................................................... 35
3-3. Magnifying a Picture ......................................................................................................................... 36
3-4. Changing Eco Mode/Checking Energy-Saving Effect .......................................................... 37
3-5. Correcting distortion of projected image ................................................................................. 39
3-6. Preventing the Unauthorized Use of the Projector [SECURITY] ........................................ 45
3-7. Displaying Two Pictures at the Same Time ............................................................................... 48
4. Using On-Screen Menu ................................................................................................................... 51
4-1. Using the Menus ................................................................................................................................ 51
4-2. List of Menu Items ............................................................................................................................. 53
4-3. Menu Descriptions & Functions [INPUT] ................................................................................... 57
4-4. Menu Descriptions & Functions [ADJUST] ................................................................................ 58
4-5. Menu Descriptions & Functions [SETUP] ................................................................................... 66
4-6. Menu Descriptions & Functions [INFO.] ..................................................................................... 83
4-7. Menu Descriptions & Functions [RESET] ................................................................................... 85
i
Table of Contents
5. Making Connections ........................................................................................................................ 86
5-1. Connecting Your Computer ........................................................................................................... 86
5-2. Connecting to a DVD player and other AV devices ............................................................... 89
5-3. Connecting to a Wired LAN ............................................................................................................ 91
5-4. Connecting to a Wireless LAN (Optional: NP05LM series) ................................................... 92
5-5. Connecting to a HDBaseT transmission device (sold commercially) .............................. 95
5-6. Portrait projection (vertical orientation) ................................................................................... 97
6. Using the VIEWER .......................................................................................................................... 100
6-1. Things you can do with the VIEWER .......................................................................................... 100
6-2. Projecting the pictures on a USB memory (basic operation) ........................................... 101
6-3. Slide screen operations .................................................................................................................. 105
6-4. File list screen operations .............................................................................................................. 106
6-5. Option menu ..................................................................................................................................... 108
6-6. Changing the logo data (background image) ....................................................................... 109
7. Connecting to a Network ........................................................................................................... 111
7-1. Things you can do by connecting the projector to a network ........................................ 111
7-2. Connecting to MultiPresenter ..................................................................................................... 112
7-3. NETWORK SETTINGS ....................................................................................................................... 114
7-4. HTTP server function ...................................................................................................................... 120
8. Maintenance .................................................................................................................................... 124
8-1. Cleaning the Lens ............................................................................................................................ 124
8-2. Cleaning the Cabinet ...................................................................................................................... 125
9. Appendix ............................................................................................................................................ 126
9-1. Setting Up the Screen and the Projector ................................................................................. 126
9-2. Compatible Input Signal List ........................................................................................................ 130
9-3. Specifications .................................................................................................................................... 132
9-4. Cabinet Dimensions ........................................................................................................................ 135
9-5. Pin assignments and signal names of main terminals ........................................................ 136
9-6. PC Control Codes and Cable Connection ................................................................................ 138
9-7. About the ASCII Control Command .......................................................................................... 140
9-8. Troubleshooting ............................................................................................................................... 142
9-9. Indicator Message ............................................................................................................................ 145
9-10. Setting the date and time in the projector .......................................................................... 149
9-11. Troubleshooting Check List ....................................................................................................... 151
9-12. REGISTER YOUR PROJECTOR! (for residents in the United States, Canada, and
Mexico) ................................................................................................................................................... 153
ii
Introduction
Thank you for purchasing the DUKANE projector.
This projector can be connected to computers, video devices, etc. to project images sharply onto
a screen.
Please read this manual carefully before using your projector and keep the manual handy for future
reference.
Read this user’s manual if you have any doubts about operation or if you believe the projector may
be faulty.
NOTES
(1) The contents of this user’s manual may not be reprinted in part or whole without permission.
(2) The contents of this user’s manual are subject to change without notice.
(3) Great care has been taken in the preparation of this user’s manual; however, should you
notice any questionable points, errors or omissions, please contact us.
(4) Notwithstanding article (3), DUKANE
other matters deemed to result from using the Projector.
will not be responsible for any claims on loss of profit or
Ver. 3 3/19
iii
Important Information
About the symbols
To ensure safe and proper use of the product, this manual uses a number of symbols to prevent
injury to you and others as well as damage to property.
The symbols and their meanings are described below. Be sure to understand them thoroughly
before reading this manual.
WARNING
CAUTION
Failing to heed this symbol and handling the product erroneously
could result in accidents leading to death or major injury.
Failing to heed this symbol and handling the product erroneously
could result in personal injury or damage to surrounding property.
Examples of symbols
This symbol indicates you should be careful of electric shocks.
This symbol indicates you should be careful of high temperatures.
This symbol indicates something that must be prohibited.
This symbol indicates something that must not be got wet.
This symbol indicates you should not touch with wet hands.
This symbol indicates something that must not be disassembled.
This symbol indicates things you must do.
This symbol indicates that the power cord should be unplugged from the power outlet.
iv
Safety Cautions
Handling the power cord
• Please use the power cord supplied with this projector. If the supplied power
cord does not satisfy requirements of your country’s safety standard, and
BE SURE TO DO
PROHIBITION
HAZARDOUS
VOLTAGE
voltage and current for your region, make sure to use the power cord that
conforms to and satisfies them.
• The power cord included with this projector is exclusively for use with this
projector. For safety, do not use it with other devices.
• Handle the power cord with care. Damaging the cord could lead to fire or
electric shock.
- Do not place heavy objects on the cord.
- Do not place the cord under the projector.
- Do not cover the cord with a rug, etc.
- Do not scratch or modify the cord.
- Do not bend, twist or pull the cord with excessive force.
- Do not apply heat to the cord.
Should the cord be damaged (exposed core wires, broken wires, etc.), ask
your dealer to replace it.
• Do not touch the power plug should you hear thunder. Doing so could result
in electric shock.
Important Information
WARNING
• The power cord you use must be approved by and
comply with the safety standards of your country.
Please refer to the page 133 about the power cord
specification.
Rated voltage by country is listed below for your refer-
ence. For selecting an appropriate power cord, please
check rated voltage for your region by yourself.
AC 230 V European countries
AC 120 V North America
v
BE SURE TO DO
PROHIBITION
DO NOT WET
UNPLUG THE
POWER CORD
Important Information
Installing the Projector
• This projector is designed to be used with a 100–240 V AC, 50/60 Hz power
supply. Before using the projector, check that the power supply to which the
projector is to be connected meets these requirements.
• Use a power outlet as the projector’s power supply. Do not connect the
projector directly to electrical light wiring. Doing so is dangerous.
• Do not use in places such as those described below. Doing so could lead to
fire or electric shock.
- Shaky tables, inclined surfaces or other unstable places
- Near heating appliances or places with heavy vibrations
- Outdoors or humid or dusty places
- Places exposed to oil smoke or steam
- Near cooking appliances, humidifiers, etc.
• Do not use in places such as those described below where the projector could
get wet. Doing so could lead to fire or electric shock.
- Do not use in the rain or snow, on a seashore or waterfront, etc.
- Do not use in a bathroom or shower room.
- Do not place vases or potted plants on the projector.
- Do not place cups, cosmetics or medicines on the projector.
Should water, etc. get inside the projector, first turn off the projector’s power,
then unplug the power cord from the power outlet and contact your dealer.
• Do not insert or drop metal or combustible objects or other foreign materials
into the projector from the vents. Doing so could lead to fire or electric shock.
Be particularly careful if there are children in the home. Should a foreign object
get inside the projector, first turn off the projector’s power, then unplug the
power cord from the power outlet and contact your dealer.
UNPLUG THE
POWER CORD
DO NOT
DISASSEMBLE
Unplug the power cord if the projector malfunctions.
• Should the projector emit smoke or strange odors or sounds, or if the projector
has been dropped or the cabinet broken, turn off the projector’s power, then
unplug the power cord from the power outlet. Failure to do so could not only
lead to fire or electric shock, it could also result in vision impairment. Contact
your dealer for repairs.
Never try to repair the projector on your own. Doing so is dangerous.
Do not disassemble the projector.
• Do not remove or open the projector’s cabinet.
Also, do not modify the projector. There are high voltage areas in the projector.
Modifying the projector could lead to fire, electric shock or leakage of laser
beams.
Have qualified service personnel perform inspection, adjustments and repairs
of the interior.
vi
CAUTION
PROHIBITION
CAUTION
FOR HIGH
TEMPERATURE
Important Information
Installing suspended from the ceiling
• Should special works be required, for example to suspend the projector from
the ceiling, consult your dealer.
Never try to install the projector yourself in such cases. The projector could
drop and cause injury.
Suspending the projector from the ceiling requires sufficient ceiling strength
to support the projector, and the building standards laws in your particular
country must be followed.
It is also necessary to take measures to prevent the projector from dropping
in anticipation of a malfunction occurring in the projector, ceiling mounting
device and installation location.
• When installed suspended from the ceiling, etc. do not hang from the projector. The projector could drop and cause injury.
• When installing suspended from the ceiling, use a power outlet that is within
reach so the power cord can be easily plugged and unplugged.
Do not place objects in front of the lens while the projector is
operating.
• Do not leave the lens cap on the lens while the projector is operating. The
lens cap could get hot and be warped.
• Do not place objects in front of the lens that obstruct the light while the
projector is operating. The object could get hot and be broken or catch fire.
• The below pictogram indicated on the cabinet means the precaution for
avoiding to place objects in front of the projector lens.
vii
PROHIBITION
PROHIBITION
Important Information
About the projector’s light source
• Do not look into the projector’s lens.
Strong light that could damage your eyes is projected when the projector is
operating. Be especially careful when children are around.
• Do not look at the projected light using optical devices (magnifying glasses,
reflectors, etc.). Doing so could result in vision impairment.
• Check that there is no one looking at the lens within the projection range
before turning on the projector.
• Do not allow children to operate the projector alone. When a child is operating
the projector an adult should always be present and watch the child carefully.
• The below pictogram, that is indicated near the lens on the cabinet, describes
this projector is categorized in the risk group 2 of IEC 62471-5:2015. As with
any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015.
When cleaning the projector
• Do not use flammable gas sprays to remove dust from the lens, cabinet, etc.
Doing so could lead to fire.
viii
BE SURE TO DO
BE SURE TO DO
DO NOT TOUCH
WITH WET
HANDS
UNPLUG THE
POWER CORD
Important Information
CAUTION
Connecting the power cord to earth
• This equipment is designed to be used in the condition of the power cord
connected to earth. If the power cord is not connected to the earth, it may
cause electric shock. Please make sure the power cord is earthed properly.
Do not use a 2-core plug converter adapter.
Handling the power cord
• When connecting the power cord to the projector’s AC IN terminal, make sure
the connector is fully and firmly inserted. Loose connection of the power cord
could lead to fire or electric shock.
• Do not connect or disconnect the power cord with wet hands. Doing so could
result in electric shock.
• When cleaning the projector, for safety purposes unplug the power cord from
the power outlet beforehand.
• When moving the projector, first be sure to turn off the power, unplug the
power cord from the power outlet and check that all connection cables connecting the projector to other devices have been disconnected.
• When planning not to use the projector for long periods of time, always
unplug the power cord from the power outlet.
PROHIBITION
BE SURE TO DO
Do not use on networks subject to overvoltage.
• Connect the projector’s Ethernet/HDBaseT port and LAN port to a network
for which there is no risk of overvoltage being applied.
Overvoltage applied to the Ethernet/HDBaseT or LAN port could result in
electric shock.
Lens shift, focus and zoom operations
• When shifting the lens or adjusting the focus or zoom, do so from either
behind or to the side of the projector. If these operations are performed from
the front, your eyes could be exposed to strong light and get injured.
• Keep your hands away from the lens area when performing the lens shift operation. If not, your fingers could get caught in the gap between the cabinet
and the lens.
ix
PROHIBITION
PROHIBITION
CAUTION
FOR HIGH
TEMPERATURE
PROHIBITION
Important Information
Handling batteries
• Handle batteries with caution. Failure to do so could lead to fire, injury or
contamination of the surroundings.
- Do not short-circuit or take apart batteries or dispose of them in flames.
- Do not use batteries other than those specified.
- Do not use new batteries together with old ones.
- When inserting batteries, pay attention to the polarities (+ and − directions),
and be sure to insert them as indicated.
• Contact your dealer or local authorities when disposing of batteries.
About the vents
• Do not obstruct the projector’s vents. Also, do not place such soft objects as
paper or cloths underneath the projector. Doing so could lead to fire.
Leave sufficient space between the place where the projector is installed and
its surroundings (as a general rule, at least 10 cm/4 inches for the intake vent,
20 cm/8 inches for the exhaust vent).
• Do not touch the exhaust vent area while projecting or immediately after
projecting images. The exhaust vent area may be hot at this time and touching it could cause burns.
Moving the projector
• When moving the projector, do not hold the lens section. The focus ring
could turn, causing the projector to drop and resulting in injury. Also, if you
put your hand on the gap between the cabinet and the lens, the projector
may be damaged, falling and causing injury.
BE SURE TO DO
Inspecting the projector and cleaning the inside
• Consult with your dealer about once per year for cleaning of the inside of the
projector. Dust could accumulate inside of the projector if it is not cleaned
for extended periods of time, leading to fires or malfunction.
x
Important Information
Laser Safety Caution
WARNING
CLASS 2 OF IEC 60825-1 SECOND EDITION LASER PRODUCT
• LASER RADIATION - DO NOT STARE INTO BEAM.
• Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
• For USA
This product is classified as Class 2 of IEC 60825-1 Second edition 2007-03.
Complies with FDA performance standards for laser products except for deviations pursuant
Laser Notice No. 50, dated June 24, 2007.
to
For other regions
This product is classified as Class 1 of IEC 60825-1 Third edition 2014-05 and RG2 of IEC
62471-5
Obey the laws and regulations of your country in relation to the installation and management
of the device.
• Outline of laser emitted from the built-in light module:
• Wave length: 449–461 nm
• Maximum power: 100 W (6660WUSSB)/82.5 W (6652WUSSB/6652WSSB)
• Radiation pattern from the protective housing:
• Wave length: 449–461 nm
• Maximum laser radiation output: 66.6 mW
• The laser module is equipped in this product. Use of controls or adjustments of procedures
other than those specified herein may result in hazardous radiation exposure.
First edition 2015-06.
Light Module
• A light module containing multiple laser diodes is equipped in the product as the light source.
• These laser diodes are sealed in the light module. No maintenance or service is required for the
performance of the light module.
• End user is not allowed to replace the light module.
• Contact qualified distributor for light module replacement and further information.
xi
Important Information
• The caution and the explanatory labels of the LASER PRODUCT in CLASS 2 conforming to IEC
60825-1 Second edition, and in Class 1 conforming to IEC 60825-1 Third edition are stuck on the
below indicated positions.
For USA
Label
For other regions
xii
Laser light radiation range
The figure below shows the maximum radiation range of the laser light.
Horizontal angle (unit: degree)
Lens position
Zoom
Wide 33.0 22.3 33.0
Tele 21.8 14.2 21.8
Right most Center (Reference value) Left most
HR HC HL
Right
HR
HC
HC
HL
Left
Important Information
Vertical angle (unit: degree)
Zoom
Wide 29.5 14.4
Tele 19.2 9.0
Lens position
Upper most Center (Reference value)
VU VC
Upper
VU
VC
VC
xiii
Important Information
Cable information
Use shielded cables or cables attached ferrite cores so as not to interfere with radio and television
reception.
For details, please refer to “5. Making Connections” in this user’s manual.
FCC Information (for USA only)
WARNING
• The Federal Communications Commission does not allow any modifications or changes to the
unit EXCEPT those specified by DUKANE in this manual. Failure
government regulation could void your right to operate this equipment.
• This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio / TV technician for help.
to comply with this
Supplier’s declaration of conformity (for USA only)
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
U.S.Responsible Party:
Address:
Telephone Number:
Type of Product:
Equipment Classification:
Model Number:
Dukane Corp
2900 Dukane Drive
St.Charles, IL 60174
(888) 245-1966
Projector
Class B Peripheral
6652WSSB/6652WUSSB/6660WUSSB
xiv
Important Information
Disposing of your used product
In the European Union
EU-wide legislation as implemented in each Member State requires that used electrical
and electronic products carrying the mark (left) must be disposed of separately from
normal household waste. This includes projectors and their electrical accessories. When
you dispose of such products, please follow the guidance of your local authority and/or
ask the shop where you purchased the product.
After collecting the used products, they are reused and recycled in a proper way. This
effort will help us reduce the wastes as well as the negative impact to the human health
and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European
Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European
union, please contact your local authority and ask for the correct method of disposal.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to
the general household waste! There is a separate collection system for used batteries,
to allow proper treatment and recycling in accordance with legislation.
According the EU directive 2006/66/EC, the battery can’t be disposed improperly. The battery
shall be separated to collect by local service.
(for Germany only)
Machine Noise Information Regulation - 3. GPSGV,
The highest sound pressure level is less than 70 dB (A) in accordance with EN ISO 7779.
Information of the AUDIO OUT mini jack
The AUDIO OUT mini jack does not support earphone/headphone terminal.
xv
Important Information
Cautions for ensuring the projector’s performance
• Do not install in places subject to vibrations or shocks.
If installed in places where the vibrations from power sources and the like are conveyed, or in
vehicles or on vessels, etc. the projector could be affected by vibrations or shocks that may damage internal parts and lead to malfunction.
Install in a place not subject to vibrations or shocks.
• Do not install near high voltage power lines or power sources.
The projector may be affected by interference if it is installed near a high voltage power line or
a power source.
• Do not install or store in such places as those described below. Doing so could lead to malfunction.
- Places where strong magnetic fields are generated
- Places where corrosive gases are generated
• If intense light like laser beams enters from the lens, it could lead to malfunction.
• Consult your dealer before using in places where much cigarette smoke or dust is present.
• When the same still image is projected for a long period of time with a computer, etc. the pattern
of the image may remain on the screen after the projection is stopped, but it will disappear after
a while. This happens due to the properties of liquid crystal panels, and is not a malfunction. We
recommend using a screensaver on the computer side.
• When using the projector at altitudes of about 1,700 m/5,500 feet or higher, be sure to set the [FAN
MODE] to [HIGH ALTITUDE]. If not, the inside of the projector may get hot, leading to malfunction.
• When the projector is used at high altitudes (places where the atmospheric pressure is low), it
may be necessary to replace the optical parts (light source, etc.) sooner than usual.
• About moving the projector
- Be sure to mount the included lens cap to protect the lens from scratches.
- Do not subject the projector to vibrations or strong shocks.
The projector could be damaged otherwise.
• Do not use the tilt feet for purposes other than adjusting the projector’s tilt.
Improper handling, such as carrying the projector by the tilt feet or using it leaned against a wall,
could lead to malfunction.
• Do not touch the surface of the projection lens with bare hands.
Fingerprints or dirt on the surface of the projection lens will be enlarged and projected on the
screen. Do not touch the surface of the projection lens.
• Do not unplug the power cord from the projector or the power outlet while projecting. Doing so
could cause deterioration of the projector’s AC IN terminal or power plug contact. To interrupt
the AC power supply while images are being projected, use a power strip switch, a breaker, etc.
• About handling of the remote control
- The remote control will not work if the projector’s remote signal sensor or the remote control’s
signal transmitter is exposed to strong light or if there are obstacles between them that obstruct
the signals.
- Operate the remote control from within 7 meters from the projector, pointing it at the projec-
tor’s remote signal sensor.
- Do not drop the remote control or handle it improperly.
- Do not let water or other liquids get on the remote control. Should the remote control get wet,
wipe it off immediately.
- Avoid using in hot and humid places as far as possible.
- When planning not to use the remote control for long periods of time, remove both batteries.
xvi
Important Information
• Take measures to prevent external light from shining on the screen.
Make sure only the light from the projector shines on the screen. The less external light on the
screen, the higher the contrast and the more beautiful the images.
• About screens
Images will not be clear if there is dirt, scratches, discoloration, etc. on your screen. Handle the
screen with care, protecting it from volatile substances, scratches and dirt.
Clearance for Installing the Projector
When installing the projector, keep sufficient space around it, as described below. If not, the hot
exhaust emitted from the projector may be taken back in.
Also, make sure no wind from an air-conditioner hits the projector.
The projector’s heat control system may detect an abnormality (temperature error) and automatically shut off the power.
20 cm/8" or greater
Wall
Exhaust vent
NOTE:
• In the above figure, it is assumed that there is sufficient space above the projector. There is also an intake vent on the back. Leave
about 10 cm or more space behind, and even more space for installing the cables.
Precautions for Ceiling Installation
Do not install the projector in the following places. Attached substances such as oil, chemicals and
moisture may cause deformation or cracks of the cabinet, corrosion of the metal parts, or malfunction.
• Outdoors and places with humid or dust
• Places exposed to oil smoke or steam
• Places where corrosive gases are generated
xvii
Important Information
About Copyright of original projected pictures:
Please note that using this projector for the purpose of commercial gain or the attraction of public
attention in a venue such as a coffee shop or hotel and employing compression or expansion of the
screen image with the following functions may raise concern about the infringement of copyrights
which are protected by copyright law.
[ASPECT RATIO], [KEYSTONE], Magnifying feature and other similar features.
Power management function
The projector has power management functions. To reduce power consumption, the power management functions (1 and 2) are factory preset as shown below. To control the projector from an
external device via a LAN or serial cable connection, use the on-screen menu to change the settings
for 1 and 2.
1. STANDBY MODE (Factory preset: NORMAL)
To control the projector from an external device, select [NETWORK STANDBY] or [SLEEP] for
[STANDBY MODE]. (→ page 79)
2. AUTO POWER OFF (Factory preset: 1 hour)
To control the projector from an external device, select [OFF] for [AUTO POWER OFF]. (→
page 81)
Model Number of Wireless LAN unit
Wireless LAN unit is an optional item.
To find the appropriate model to your area, please visit the company website:
http://www.dukaneav.com
Note: The Dukane models described in this document are manufactured by NEC and use the same
firmwa e, software programs, control code, and accessory parts. The equivalent Dukane to NEC
models are 6652WSSB ( NP-P525WL), 6652WUSSB ( NP-P525UL) and 6660WUSSB (NP-P605UL).
xviii
Important Information
Trademarks
• MultiPresenter is a trademark or registered trademark of NEC Display Solutions, Ltd. in Japan and
other countries.
• Apple, Mac, MacBook, and iMac are trademarks of Apple Inc. registered in the U.S. and other
countries.
• Microsoft, Windows, and PowerPoint are either a registered trademark or trademark of Microsoft
Corporation in the United States and/or other countries.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and
other countries.
• HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
• PJLink trademark and logo are trademarks applied for registration or are already registered in
Japan, the United States of America and other countries and areas.
• Wi-Fi®
• Blu-ray is a trademark of Blu-ray Disc Association
• CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of Crestron
• Extron and XTP are registered trademarks of RGB Systems, Inc. in the United States.
• Ethernet is either a registered trademark or trademark of Fuji Xerox Co., Ltd.
• Other product names and company logos mentioned in this user’s manual may be the trademarks
• GPL/LGPL Software Licenses
is a registered trademark of the Wi-Fi Alliance®. WPA™, WPA2™ are trademarks of the Wi-Fi
Alliance®.
Electronics, Inc. in the United States and other countries.
or registered trademarks of their respective holders.
The product includes software licensed under GNU General Public License (GPL), GNU Lesser
General Public License (LGPL), and others.
xix
1. Check the product overview, supplied items and part names
1-1. Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
General
• Liquid crystal type high brightness/high resolution projector
Model name Brightness Resolution Aspect ratio
6660WUSSB 6,000 lm
6652WUSSB 5,000 lm
6652WSSB 5,000 lm
• A proprietary sealed structure that achieves highly dust-proof performance
Due to its excellent dust-proof performance, the projector is not equipped with a filter. Filter
replacement is therefore unnecessary.
• Silent design utilizing a sealed structure
A silent design with no irritating fan noise even in a quiet conference room or classroom.
Light source · Brightness
• A long-life laser diode is equipped in the light module
The product can be operated at low cost because the laser light source can be used for a long
time without requiring replacement or maintenance.
• Brightness can be adjusted within a wide range
Unlike with ordinary light sources, the brightness can be adjusted from 30 to 100% in 1% increments.
• [CONSTANT BRIGHTNESS] mode
Brightness normally decreases with use, but by selecting [CONSTANT BRIGHTNESS] mode, the
projector automatically controls the output from the light module according to the light module
used time for maintaining constant brightness.
WUXGA
(1920 × 1200 pixels)
WUXGA
(1920 × 1200 pixels)
WXGA
(1280 × 800 pixels)
16:10
16:10
16:10
1
1. Check the product overview, supplied items and part names
Installation
• 360° installation and portrait projection
The projector can be installed at any angle from 0° to 360° in both the vertical and horizontal
direction. When installing the projector in a tilted position, use brackets of sufficient strength.
Portraits can also be projected with the projection screen tilted 90°. Be sure to assemble and
install a dedicated stand.
• Lens shift mechanism for adjusting the position of the projected image easily
The position of the projected image is moved by turning the two dials on the projector cabinet
top, one for the vertical direction and another for the horizontal direction.
• Correct projected image distortion on specially shaped surfaces
Distortion when projecting on specially shaped surfaces (cylindrical or spherical surfaces, for
example) can be corrected using our Geometric Correction Tool application.
Videos
• Wide range of input terminals (HDMI × 2, HDBaseT, etc.)
The projector is equipped with a variety of input terminals: HDMI (× 2), Computer (analog), Video,
HDBaseT, etc. HDMI input terminal on this product supports HDCP. HDBaseT is a connection
standard for home appliances that is established by the HDBaseT Alliance.
• Simultaneous display of 2 images (PIP)
With this projector, it is possible to project 2 images with a single projector, by displaying a
small sub-display within the main display. Furthermore, the sub-display display position can
be changed and the main display and sub-display images can be swapped.
• [VIEWER] function to project still images saved in a USB memory
When you insert a commercially available USB memory containing the picture into the USB port
of the projector (Type A), the images on the USB can be projected by the unit. By doing this,
you can make a presentation without using a personal computer.
• Seamless switch function for smoother screen changes when switching the signal
When the input connector is switched, the image displayed before switching is held so that that
the new image can be switched to without a break due to absence of a signal.
2
1. Check the product overview, supplied items and part names
Network
• Compatible with wired LAN / wireless LAN
Equipped with a LAN port (RJ-45), the projector can be connected to a wired LAN to transmit
images from a computer to this unit or to control this unit from the computer. In addition, when
a wireless LAN unit sold separately is attached to the unit, the unit can be connected to a wireless LAN.
• CRESTRON ROOMVIEW and Extron XTP compatibility
The projector supports CRESTRON ROOMVIEW and Extron XTP, allowing multiple devices connected in the network to be managed and controlled from a computer. Moreover, it enables to
output and control image via an Extron XTP transmitter connected with the projector.
• Compatible with the MultiPresenter application
This projector is compatible with the NEC MultiPresenter application, so multi-screen projection
is possible via the network (wired LAN/wireless LAN).
Energy-saving
• 0.13 W (100-130 V AC)/0.19 W (200-240 V AC) in standby condition with energy saving
technology
Selecting [NORMAL] for [STANDBY MODE] from the menu can put the projector in power-saving
mode.
NORMAL: 0.13 W (100-130 V AC)/0.19 W (200-240 V AC)
NETWORK STANDBY: 1.4 W (100-130 V AC)/1.6 W (200-240 V AC)
• [ECO MODE] for low power consumption and [CARBON METER] display
The projector is equipped with a [ECO MODE] for reducing power consumption during use.
Furthermore, the power-saving effect when the [ECO MODE] is set is converted into the amount
of reductions of CO
when the power is turned off and at [INFO.] on the on-screen menu ([CARBON METER]).
emissions and this is indicated on the confirmation message displayed
2
3
1. Check the product overview, supplied items and part names
1-2. What’s in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your projector.
Projector
Power cord
(US: 7N080236/7N080242)
(EU: 7N080022/7N080028)
Remote control
(7N901171)
Computer cable (VGA)
(7N520089)
• Information sheet
• Security Sticker
(Use this sticker when security password is set on.)
Lens cap strap
Batteries (AAA × 2)
4
1. Check the product overview, supplied items and part names
1-3. Part Names of the Projector
Front
1
6
7
2
3
4
5
1. Lens shift cover
(→ page 23)
2. Zoom Lever
(→ page 26)
3. Lens
4. Focus Ring
(→ page 25)
5. Lens Cap
6. Indicators
(→ page 8, 145)
7. Remote Sensor
(→ page 14)
8. Monaural Speaker
9. Controls
(→ page 8)
10. Security Slot ( )
8
9
10
11
12
11. Security chain opening
Attach an anti-theft device.
The security chain opening accepts security
wires or chains up to 0.18 inch/4.6 mm in
diameter.
12. Tilt Foot
(→ page 27)
TIP:
• Security and theft protection lock compatible with
Kensington security cables/equipment. For products, visit
Kensington’s website.
5
1. Check the product overview, supplied items and part names
Mounting the lens cap strap
1. Insert the tip of the strap into the lens cap
mount hole and pass the knot through.
2. Insert the knot into the strap mount hole
(large) on the bottom of the projector, then
press it into the narrow (small) hole.
Lens cap mount hole
6
Rear
1. Check the product overview, supplied items and part names
1
4
3
2
1. Terminal Panel
(→ page 9)
2. AC Input
Connect the supplied power cord’s threepin plug here, and plug the other end into
an active wall outlet.
(→ page 16)
3. Intake Vent
4. Remote Sensor
(→ page 14)
5. Exhaust Vent
5
7
Controls/Indicators
3 2
4
1. Check the product overview, supplied items and part names
5
1
6
1. (POWER) Button
(→ page 18, 33)
2. POWER Indicator
(→ page 16, 18, 33, 145)
3. STATUS Indicator
(→ page 145)
4. LIGHT Indicator
(→ page 145)
5. INPUT Button
(→ page 20)
6. MENU Button
(→ page 51)
7. EXIT Button
(→ page 51)
8. ▲▼◀▶ / Volume Buttons ◀▶ / Keystone Button ▼
(→ page 28, 32, 51)
9. ENTER Button
(→ page 51)
7
8
9
8
Terminal Panel Features
1. Check the product overview, supplied items and part names
95476213810
1. HDMI 1 IN Terminal (Type A)
(→ page 86, 88, 90)
2. HDMI 2 IN Terminal (Type A)
(→ page 86, 88, 90)
3. COMPUTER IN/ Component Input Terminal (Mini D-Sub 15 Pin)
(→ page 86, 89)
4. AUDIO IN Mini Jack (Stereo Mini)
(→ page 86, 89)
5. AUDIO OUT Mini Jack (Stereo Mini)
Audio signal of the image projected from
the projector is output.
When audio equipment is connected, the
projector speaker is disabled.
6. Ethernet/HDBaseT Port (RJ-45)
(→ page 95)
7. LAN Port (RJ-45)
(→ page 91)
8. USB Port (Type A)
Connect the USB memory. When picture
data is saved in a USB memory, the picture
can be projected with the [VIEWER] of the
projector.
(→ page 100)
In addition, a 5 V/2.0 A power supply can be
supplied for expansion use.
9. PC CONTROL Port (D-Sub 9 Pin)
Use this port to connect a PC or control
system. This enables you to control the projector using serial communication protocol.
If you are writing your own program, typical
PC control codes are on page 138.
10. Wireless LAN cover ( )
There are two terminals behind the cover.
• USB (Wireless LAN) Port
(→ page 93)
• SERVICE Port (USB Type B)
(for service purpose only)
9
1. Check the product overview, supplied items and part names
1-4. Part Names of the Remote Control
11
1
2
5
8
1. Infrared Transmitter
3
4
6
7
10
9
(→ page 14)
2. POWER ON Button
(→ page 18)
3. POWER STANDBY Button
(→ page 33)
4. SOURCE Button
(→ page 20)
5. HDMI1 Button
(→ page 20)
6. HDMI2 Button
(→ page 20)
7. HDBaseT Button
(→ page 20)
8. DisplayPort Button
(This button does not work in this series of projectors)
9. COMPUTER Button
(→ page 20)
10. AUTO ADJ. Button
(→ page 32)
11. VIDEO Button
(This button does not work in this series of projectors)
10
Loading...