Dukane 28A9115A User Manual

Liquid Crystal Projector
LCOS Technology
Model
28A9115A
User's Manual
Liquid Crystal Projector
USER'S MANUAL
USER'S MANUAL
Thank you for purchasing this liquid crystal projector.
WARNING • Please read the accompanying manual “SAFETY
INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference.
NOTE
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without express written authority.
TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the trademarks and registered trademarks of all companies, even when not mentioned.
CONTENTS
CONTENTS
FEATURES .......................................2
BEFORE USE ...................................2
Contents of Package ..............................2
Part Names.............................................3
Loading the Batteries..............................5
INSTALLATION ................................6
Installation of the Projector and Screen
Angle Adjustment ...................................6
Cabling ...................................................7
Power Connection ..................................8
Example of System Setup ......................8
Plug & Play.............................................8
OPERATIONS...................................9
Power On ...................................................9
Power Off
Basic Operation....................................10
Setup Menu ..........................................12
Input Menu............................................13
Image Menu..........................................14
Options Menu .......................................15
No Signal Menu....................................16
MAINTENANCE ..............................17
Lamp.....................................................17
Air Filter ................................................19
Other Maintenance...............................19
• The information in this manual is subject to change without notice.
Page
TROUBLESHOOTING ....................20
OSD Message ......................................20
Indicators Message ..............................21
Symptom ..............................................22
SPECIFICATIONS...........................23
WARRANTY AND AFTER-SERVICE
........6
.......................................................................................
TABLES
Table 1. Installation Reference.................6
Table 2. Cabling .......................................7
Table 3. Basic Operation........................10
Table 4. Setup Menu ..............................12
Table 5. Input Menu................................13
................................................9
Table 6. Image Menu..............................14
Table 7. Options Menu ...........................15
Table 8. No Signal Menu........................16
Table 9. OSD Message ..........................20
Table 10. Indicators Message ................21
Table 11. Symptom ................................22
Table 12. Specifications .........................23
.......................................................................................
For "TECHNICAL" and "REGULATORY NOTICE", see the end of this manual.
......24
ENGLISH
Page
ENGLISH-1
FEATURES
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
NORSK
PORTGÊS
Liquid Crystal Projector
CP-SX5500W
USER'S MANUAL
Please read this user's manual thoroughly to ensure correct usage through understanding.
BEDIENUNGSANLEITUNG
Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung aufmerksam.
MANUEL D'UTILISATION
Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le fonctionnement de l'appareil.
MANUALE D'ISTRUZIONI
Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter comprendere quanto riportato ai fini di un corretto utilizzo del proiettore.
MANUAL DE USUARIO
Lea cuidadosamente este manual del usuario para poder utilizar corretamente el producto.
GEBRUIKSAANWIJZNG
Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te hebben van de uitgebreide mogelijkheden.
BRUKERHÅNDBOK
Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.
INSTRUÇÕES DO PROPRIETÁRIO
Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do usuário.
TECHNICAL
REGULATORY NOTICES
FEATURES
This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.
Outstanding Brightness
The UHB lamp and high-efficiency optical system assure a high level of brightness.
Partial Magnification Function
Interesting parts of images can be magnified for closer viewing.
Distortion Correction Function
Distortion-free images are quickly available.
Extra-low Noise Function
Acoustic noise level from the unit can be reduced.
BEFORE USE
BEFORE USE
Contents of package
Make sure all of the following items are included in the package. If anything is missing, please contact your dealer.
NOTE
(with Lens Cap)
User’s Manual
(this manual)
Safety Instructions
ENGLISH-2
Keep the original packing material for future reshipment.
Power Cord
(US Type)
Projector
RGB Cable Video/Audio Cable
Mouse cable
(PS/2)
Power Cord
(with white lead)
for Remote Control
(UK Type)
Batteries
Transmitter
Power Cord
(Europe Type)
Component
Video Cable
(with green lead)
BLANK
STANDBY/ON
LASER
RGB
VIDEO
AUTO
MENU
KEYSTONE
MENU SELECT
RESET
POSITION
FREEZE
PinP
MAGNIFY
MUTE
OFF
VOLUME
Remote Control
Transmitter
BBBBEEEEFFFFOOOORRRREEEE UUUUSSSSEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
Part Names
))
TEMP Indicator
LAMP Indicator
STANDBY/ON Button
((
STANDBY/ON Indicator)
VIDEO Button
RGB Button
Remote Control Sensor
Lens
AC Inlet
(to Power Cord)
Power Switch
Lens Cap
Remote Control Sensor
Speaker
LAMP TEMP
123
INPUT SELECT
STANDBY / ON
Control Panel
(Refer to P.9 "OPERATIONS")
Front/Right View
KEYSTONE
RGBVIDEO RESET MENU
KEYSTONE Button
MENU Button
RESET Button
Control Panel
Ventilation Openings (exhaust)
Carrying Handle
Air Filter and Intake for the Cooling Fan
Foot Adjuster
Terminal Panel
(Refer below)
ENGLISH
COMPONENT VIDEO
Y Terminal CB/PB Terminal CR/PR Terminal
VIDEO Terminal
VIDEO AUDIO IN
R Terminal
L/MONO Terminal
AUDIO OUT Terminal
RGB AUDIO IN
RGB 1/DVI Terminal
RGB 2 Terminal
COMPONENT VIDEO
CR/PR
R
VIDEO AUDIO IN
AUDIO OUT
Rear/Left View
VIDEO IN
L/MONO
RGB1/DVl
RGBAUDIO IN
VIDEO
23
S-VIDEO
1
RGB2
USB
CB/PB Y
Terminal Panel
DVl
3
RGB IN
12
RGB OUT CONTROL
DVI Terminal
RGB IN 1 Terminal RGB IN 2 Terminal
RGB OUT Terminal CONTROL Terminal
S-VIDEO Terminal
USB Terminal
ENGLISH-3
BBBBEEEEFFFFOOOORRRREEEE UUUUSSSSEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
S
T
A
N
D
B
Y
/O
N
LASER
BLANK
RGB
VIDEO
AUTO
MENU
MENU SELECT
KEYSTONE
R
E
SET
FR
EEZE
PinP
MAGNIFY
POSITION
OFF
VOLUME
MUTE
Part Names (continued)
STANDBY/ON Button
VIDEO Button
Disk Pad
Used to operate the mouse shift function and left click function.
AUTO Button
MENU Button
MENU SELECT Button
Used to click the left mouse button.
, , , Button
Used to operate the mouse shift function.
POSITION Button
MAGNIFY Button
REMOTE CONTROL TRANSMITTER
(Refer to P.9 "OPERATIONS")
))
BLANK Button LASER Button
RGB Button MOUSE / RIGHT Button
Used to click the right mouse button.
KEYSTONE Button
RESET Button
Used to click the right mouse button.
FREEZE Button PinP Button MUTE Button VOLUME Button
These functions work when the mouse control function is activated. Remember, the POSITION,
BLANK ON and MENU ON functions disable the mouse control function.
WARNING • The laser pointer of the remote control transmitter is used in place of a finger or rod. Never look directly into the laser beam outlet or point
the laser beam at other people. The laser beam can cause vision problems.
AVOID EXPOSURE-
LASER RADIATIONS IS
EMITTED FROM THIS
APERTURE
Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to Laser Notice No.50, dated 2001.7.26 SMK CORPORATION
NOTE
• Do not give the remote control transmitter any physical impact. Take care not to drop.
• Do not place the heavy objects on the remote control transmitter.
• Do not wet the remote control transmitter or place it on any wet object.
• Keep the remote control transmitter away from children and pets.
• Do not place the remote control transmitter close to the cooling fan of the projector.
• Do not disassemble the remote control transmitter.
6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511 MANUFACTURED PLACE OF MANUFACTURER: A
Novemver 2001
CAUTION
LASER RADIATION­DO NOT STARE INTO BEAM MAX. OUTPUT: 1mW WAVE LENGTH
: 650nm
CLASS2 LASER PRODUCT
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS2 LASER PRODUCT MAX. OUTPUT: 1mW WAVE LENGTH: 650nm
IEC60825-1 :1993+A1:1997
ENGLISH-4
BBBBEEEEFFFFOOOORRRREEEE UUUUSSSSEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Loading the Batteries
Install the AA batteries into the remote control transmitter.
1. Remove the battery cover. Push the knob while lifting up the battery cover.
2. Load the batteries. Make sure the plus and minus poles are correctly oriented.
3. Close the battery cover.
CAUTION Use only the specified batteries with this remote control transmitter. Also, do not mix new and old batteries. This could cause battery
cracking or leakage, which could result in fire or personal injury.
When loading the batteries, make sure the plus and minus terminals are correctly oriented as indicated in the remote control transmitter. Incorrect orientation could cause battery cracking or leakage, which could result in personal injury or pollution of the surrounding environment.
When you dispose the battery, you should obey the law in the relative area or country.
Keep the battery away from children and pets.
When not to be used for an extended period, remove the batteries from the
remote control transmitter.
1
2
ENGLISH
NOTE
Replace the batteries when remote control transmitter operation becomes difficult.
ENGLISH-5
INSTALLATION
INSTALLATION
Installation of the Projector and Screen
Refer to the drawing and table below for determining the screen size and projection distance.
The projection distances shown in the table below are for full size (1365 x 1024 dots). a: Distance from the projector to the screen. (±10%)
Table 1. Installation Reference
Screen size [inches (m)]
40 (1.0) 65 (1.6) 85 (2.2) 60 (1.5) 98 (2.5) 127 (3.2)
80 (2.0) 131 (3.3) 170 (4.3) 100 (2.5) 164 (4.2) 213 (5.4) 120 (3.0) 196 (5.0) 255 (6.5) 150 (3.8) 246 (6.2) 319 (8.1)
200 (5.0) 328 (8.3) 426 (10.8)
CAUTION Install the projector in a suitable environment according to
instructions of the accompanying manual SAFETY INSTRUCTIONS and this
manual.
When you fix this unit with a metal tool and the like, you must connect it with ground wire; otherwise, fire or electric shock can result. Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the building using an optional three-core power-supply cord.
Please basically use liquid crystal projector at the horizontal position. liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and cause damage. careful not to install it with ventilation holes blocked.
Do not install LCD projector in smoke effected environment. Smoke residue may buildup on critical parts (i.e.LCD panel, Lens Assy etc.).
a [inches (m)]
Min. Max.
Screen
Lens center
a
Top View
Side View
If you use
Be especially
Angle Adjustment
Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable within 0˚ to 8˚ approximately.
1. Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle.
2. Release the button to lock at the desired angle.
3. Use the foot adjusters for fine adjustment, Do not force the foot adjuster screws. This could damage the adjusters or cause the lock to fail.
CAUTION being held; otherwise, the projector could overturn or fingers could get
caught and cause personal injury.
Do not release the foot adjuster button unless the projector is
ENGLISH-6
Foot Adjusters
Variable within the range of approximately 0° - 8°
IIIINNNNSSSSTTTTAAAALLLLLLLLAAAATTTTIIIIOOOONNNN ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Cabling
Refer to the table below for connecting each terminal of the projector to a device.
Table 2. Cabling
Function Terminal Cable
Analog RGB input
Analog RGB output RGB OUT
DVI input DVI DVI cable with inch thread screws
Audio input (from the computer)
PS/2 mouse control
ADB mouse control ADB mouse cable
Serial mouse control Serial mouse cable
RS-232C communication RS-232C cable USB mouse control USB USB cable
S-video input S-VIDEO S-video cable with mini DIN 4-pin jack
Video input VIDEO Video/Audio cable
Component video input
Audio input (from video equipment)
Audio output AUDIO OUT Audio cable with stereo mini jack
RGB IN 1 RGB IN 2
RGB AUDIO IN [RGB 1 / DVI]
(interlocked with RGB IN 1 or DVI)
RGB AUDIO IN [RGB 2]
(interlocked with RGB IN 2)
CONTROL
COMPONENT VIDEO [Y]
COMPONENT VIDEO [CR AUDIO [L / MONO] AUDIO [R]
/PR]
RGB cable with D-sub 15-pin shrink jack and inch thread screws
Audio cable with stereo mini jack
PS/2 mouse cable
Component Video cableCOMPONENT VIDEO [CB/PB]
Video/Audio cable or Audio cable with RCA jack
ENGLISH
CAUTION Incorrect connecting could result in fire or electrical shock. Please read this manual and the separate SAFETY INSTRUCTIONS”.
Before connecting, turn off to all devices to be connected, except for the USB cable.
The cables may have to be used with the core set to the projector side. Use the cables which are included with the projector or specified.
NOTE
projector is compatible with the device.
• Secure the screws on the connectors and tighten.
• For some RGB input modes, the optional Mac adapter is necessary.
• To select the DVI input, the computer may need some settings. See the manuals of the computer for details.
• Some computers may have multiple display screen modes. Use of some of these modes will not be possible
with this projector.
• Refer to the “TECNICAL” section for the pin assignment of connectors and RS-232C communication data.
• When the DVI terminal is used, the RGB OUT terminal may not function.
• Before connecting, read instruction manuals of the devices to be connected, and make sure that the
ENGLISH-7
IIIINNNNSSSSTTTTAAAALLLLLLLLAAAATTTTIIIIOOOONNNN ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Power Connection
Use the correct power cord depending on the power outlet to be used. Connect the AC inlet of the projector to the power outlet firmly by the power cord.
CAUTION Be carful in handling the power
cord according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual.
Connect the power cord firmly. Avoid using a loose, unsound outlet or failed contact.
Example of System Setup
Computer
(desktop type)
DVD Player
VIDEO IN
S-Video Tape Recorder
Speaker with amplifier
COMPONENT VIDEO
CR/P
R
R
VIDEO AUDIO IN
AUDIO OUT
CB/PBY
L/MONO
RGB1/DVl
RGBAUDIO IN
VIDEO
RGB2
23
12
S-VIDEO
1
USB
Computer
(desktop type)
RGB OUT CONTROL
Power
outlet
Power Cord
AC Inlet
DVl
3
RGB IN
Computer
(notebook type)
Display Monitor
NOTE
• When connecting with a notebook computer, set the proper RGB external image output (setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of the notebook for more information.
Plug & Play
This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is VESA DDC (Display Data Channel) compatible. Please use this function by connecting the RGB cable with RGB IN 1 terminal (DDC 1/2B compatible), or by connecting a DVI cable with DVI terminal (DDC 2B compatible). Plug & play may not operate by other connections.
NOTE
display and an operating system.
• This projector is recognized as a plug & play monitor. Use the standard display drivers.
• Plug & play may not operate by the computer to connect. Use the RGB IN 2 terminal if plug & play does not operate correctly.
ENGLISH-8
• Plug & play is a system configured with peripheral equipment including a computer,
OPERATIONS
OPERATIONS
Power Switch
Lens cap
STANDBY/ON Button
(STANDBY/ON Indicator)
Focus Ring
STANDBY/
ON Button
Zoom Knob
STANDBY/ON
VIDEO
AUTO
MENU
MENU SELECT
POSITION
MAGNIFY
LASER
FREEZE
OFF
BLANK
RGB
KEYSTONE
RESET
PinP
MUTE
VOLUME
Power ON
1. Check that the power cord is connected correctly.
2.
Set the power switch to [ | ]. The standby mode is selected, and the STANDBY/ON indicator is turned to orange.
3. Press the STANDBY/ON button on the control panel or the remote control transmitter. Warm-up begins and the STANDBY/ON indicator blinks in green.
4.
The STANDBY/ON indicator ceases blinking and turns to green when power is on. Remove the lens cap.
5. Adjust picture size using the Zoom Knob.
6. Adjust focus using the Focus Ring .
Power OFF
1.
Press the STANDBY/ON button on the control panel or the remote controller. Then,the message "Power off?" will appear on the screen, and the message will disappear by any operation or no operation for 5 seconds. During this message indication, press the STANDBY/ON button again. The projector lamp is extinguished and lamp cooling begins. The STANDBY/ON indicator blinks orange during lamp cooling. Pressing the STANDBY/ON button has no effect while the STANDBY/ON indicator is blinking.
2.
The system assumes the Standby mode when cooling is complete, and the STANDBY/ON indicator ceases blinking and changes to orange. Check that the indicator is orange and set the Power switch to [O].
3. The STANDBY/ON indicator is extinguished when power is off. Attach the lens cap. Put the Lens cap to the lens properly. In order to do it, keep pushing two knobs on the lens cap, then fit it to the lens holding the cap in horizontal position.
WARNING Please read this manual, and the separate SAFETY INSTRUCTIONS thoroughly before using the equipment. Always ensure that
the equipment is used safely.
ENGLISH
NOTE
Except in emergencies, follow the above-mentioned procedure for turning power off. If the projector is used improperly, it may very difficult to turn off the projector caused by heating inside the unit. And the reduction of life time of lamp and LCD panels will be caused by incorrect procedure.
• To prevent any trouble, turn on/off the projector when the computer or video tape recorder is OFF. Providing a RS-232C cable is connected, turn on the computer before the projector.
• When a projector continues projecting the same image, the image may remain as an afterimage. Please do not project the image same for a long time.
ENGLISH-9
ENGLISH-9
OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
OFF
))
Basic Operation
The basic operations shown in Table 3 is performed from the supplied remote control transmitter or the projector control panel. Items indicated by (*) may be used from the control panel.
Table 3 . Basic Operation
Item Description
Select RGB Input : Press the RGB button.
VIDEO/S-VIDEO/COMPONENT VIDEO RGB IN 1/RGB IN 2/DVI
INPUT SELECT (
POSITION
RESET (*)
MAGNIFY
FREEZE
RGB IN 1 RGB IN 2 DVI (RGB IN 1)
Select Video Input : Press the VIDEO button.
*)
RGB IN 1/RGB IN 2/DVI VIDEO/S-VIDEO/COMPONENT VIDEO VIDEO S-VIDEO COMPONENT VIDEO (VIDEO)
The selected signal name is displayed for approximately 3 seconds when the input signal is changed.
Set/Clear Position Adjustment Mode : Press the POSITION button.
The [ ] icon is displayed in the POSITION mode.
Image Position Adjustment: Press the , , and buttons in the POSITION mode.
Valid only in the MAGNIFY mode with a video signal is input.
After approximately 10 seconds of inactivity the [ ] icon is extinguished and the
POSITION mode is cleared automatically.
, , and
Initialize Each Item : Select an item and press the RESET button. Initialize Position Adjustment : Press the RESET button and the
POSITION mode. This function is valid only when RGB signal is input.
Valid except for the VOLUME, LANGUAGE, WHISPER and H PHASE.
The RESET button may operate as the mouse control button. Refer to page 4.
Set MAGNIFY Mode : Press the MAGNIFY button. Move Magnified Area : Run the POSITION in the MAGNIFY mode. Adjust Magnification : Press the MAGNIFY / button in MAGNIFY
mode. Clear MAGNIFY Mode : Press the MAGNIFY button.
The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT SELECT or VIDEO, or by changing the input signal.
Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is displayed, and the image is frozen, in the FREEZE mode.
The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE, Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, KEYSTONE, or by changing the input signal.
Do not forget to clear frozen static images.
buttons may operate as the mouse control button. Refer to page 4.
NOTE
the front of the projector, and within a range of 30° left-right. Strong light and obstacles will interfere with operation of the remote control transmitter.
• Use the remote control transmitter at a distance of approximately 5m from the sensor on
ENGLISH-10ENGLISH-10
OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
Item Description
VOLUME
MUTE
AUTO
BLANK ON/OFF
MENU ON/OFF
MENU SELECT
Volume Adjustment : Press the VOLUME / button. Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the
MUTE mode. Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and horizontal size(H.SIZE) are automatically adjusted. Use with the window at maximum size in the application display. Automatic Adjustment at Video Input : Press the AUTO button. A signal type appropriate for the input signal is selected automatically. Valid only when AUTO is set for VIDEO on the menu.
This operation requires approximately 10 seconds. It may not function correctly with some input signals.
Set/Clear Blank Mode: Press the BLANK button. No image is displayed in the Blank mode. The screen color is as set in BLANK on the Image menu.
Menu Display Start/Stop: Press the MENU button.
The menu display is terminated automatically after approximately 10 seconds of inactivity.
Select Menu Type: Press the MENU SELECT button. Allows the user to select the normal menu or the single menu. Only the selected item is displayed on the single menu, and other items are displayed with the and buttons as with the normal menu.
Valid only when the Setup menu is used. Push the MENU SELECT button after selecting items such as "BRIGHTNESS".
The MENU SELECT button may operate as the mouse control button. Refer to page 4.
Normal menu Single menu
SETUP INPUT OPT.IMAGE
BRIGHT
CONTRAST
V POSIT H POSIT H PHASE
H SIZE
COLOR BAL R COLOR BAL B
ASPECT
100 100
+1
800
(MENU SELECT)
0
-2
0 0
))
CONTRAST
ENGLISH
-2
P.IN P. MODE
KEYSTONE
Select Mode of P.IN P. Display : Press the PinP button.
Large P.IN P. off (→Small)
Small
P.IN P. function superimposes a video image over RGB or DVI signals.
Set / Clear KEYSTONE Mode : Press the KEYSTONE button. Select KEYSTONE Mode : Press the / button in the KEYSTONE
mode. Vertical
Horizontal
Adjust KEYSTONE : Press the / button.
The image may not be appeared properly when this function is activated on some input signals.
The adjustable range of distortion correction will be different among input signals.
ENGLISH-11
ENGLISH-11
OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE COLOR BAL R COLOR BAL B
ASPECT
0
-2
+1
0 0
100 100
800
SETUP INPUT OPT.IMAGE
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
H PHASE COLOR BAL R COLOR BAL B
ASPECT
0 +1 +1 0 0 0 0 0
SETUP INPUT OPT.IMAGE
Setup Menu
The following adjustments and settings are possible when SETUP is selected at the top of the menu. Part of the Setup menu differs between RGB input and video input. Select an item with the and buttons, and start operation. Use the Single menu to reduce menu size (see Table 3, MENU SELECT).
Table 4. Setup Menu
RGB IN 1 RGB IN 2
DVI
))
VIDEO
S-VIDEO
COMPONENT VIDEO
Item Description
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
SHARPNESS
COLOR
TINT
COLOR BAL R
COLOR BAL B
ASPECT
ENGLISH-12ENGLISH-12
DVI
COMPONENT
- -
- -
-
VIDEO
S-VIDEO
Adjustment: Dark Light
Adjustment: Weak Strong
Adjustment: Down Up
Adjustment: Left Right Adjustment: Left Right
Adjust to eliminate flicker.
RGB IN 1 RGB IN 2
Adjustment: Small Large
The image may not be displayed correctly if the horizontal size is excessive. In such cases, press the RESET button, and initialize the horizontal size.
Adjustment: Soft Clear
Adjustment: Light Dark Adjustment: Red Green
Valid only when NTSC or NTSC 4.43 signal is received.
Adjustment: Light Dark Adjustment: Light Dark
- -
- -
- -
- -
Select Image Aspect Ratio :
Full [ ]
Select Position of Image:
16:9[ ] Real [ ]
-
Press the button while 16:9[ ] is selected. Center
Down Up ( Center )
Select Image Aspect Ratio:
4:3[ ]
16:9[ ] 4:3 small[ ]
Select Position of Image :
Press the button while 16:9[ ] / 4:3 small[ ] is selected. Center
Down Up ( Center )
- -
4:3 small may not be displayed correctly with some input signals.
OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Input Menu
The following functions are available when INPUT is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. The function indicated (**) are effective on video input mode only, not on RGB input mode, except in the P.IN P. window on RGB input mode.
Table 5. Input Menu
Item Description
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button.
Horizontal position (H.POSIT), vertical position (V.POSIT), clock phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted. Use with the window at maximum size in the application display.
AUTO
RGB
VIDEO (**)
BLACK (**)
Progressive
(**)
HDTV
Automatic Adjustment at Video Input: Select the button. A signal type appropriate for the input signal is selected automatically when
EXECUTE
is selected automatically. Valid only when
AUTO is set for VIDEO on the menu.
This operation requires approximately 10 seconds. It may not function correctly with
some input signals. Pressing the AUTO button in this case may correct this problem.
This function is the same as for the AUTO function in Basic operation.
Displays RGB Input Frequency: Displays the horizontal and vertical sync signal frequencies for RGB input.
Valid only at RGB input.
Select Video Signal Type: Select the signal type with the and buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as appropriate for the input signal. The selection of AUTO enables and executes the function AUTO (Automatic Adjustment at Video Input), except for the N-PAL input.
Use this function when the image becomes unstable (eg. the image becomes irregular, or lacks color) at VIDEO/S-VIDEO input.
Automatic Adjustment requires approximately 10 seconds. It may not function correctly with some input signals. Pressing the AUTO button in this case may correct this problem except for the N-PAL input.
For the COMPONENT VIDEO input, this function is not effective and the signal type is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the signal of HDTV.
Set/Clear Black Enhancement Mode: Select the TURN ON / TURN OFF with the / button. When the TURN ON is selected, the black enhancement mode is active and the contrast ratio of the screen for the video input will be raised by making black level darker.
Select Progressive Mode: Select the mode suitable for the input signal with the and buttons. The TV mode and the FILM mode convert the interlaced video signal into the progressive signal. The FILM mode is adptable 2-3 Pull-Down system to the conversion.
Use this function to raise resolution, at the interlaced video input except HDTV signal.
Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the input signal with the / button.
SETUP INPUT OPT.
AUTO
RGB
VIDEO
Progressive
BLACK
HDTV
EXECUTE
with the
IMAGE
EXECUTE CANCEL
ENGLISH
ENGLISH-13
ENGLISH-13
OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Image Menu
The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons.
Table 6. Image Menu
Item Description
BLANK
MIRROR
START UP
P. IN P. POSIT
P. IN P. INPUT
GAMMA
Select Blank Screen Color: Select color with the and buttons.
The image is cleared and the entire screen is displayed in the selected color, when BLANK mode is set with BLANK ON, or when there is no signal for 5 minutes.
Select Mirror Status: Select mirror status with and buttons. Setup Initial Screen Display: Select TURN ON with the button.
Clear Initial Screen Display: Select TURN OFF with the button.
Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal.
Select Position of P. in P. Display : Press the or button.
↔↔↔
P.IN P. function superimposes a video image over RGB or DVI signals.
Select signal of P. in P. Display : Press the or button.
VIDEO
S-VIDEO COMPONENT
Select Gamma mode: Select the gamma mode with the / button.
NORMAL
CINEMA DYNAMIC
SETUP INPUT OPT.IMAGE
BLANK
MIRROR
START UP P. IN P.POSIT P.IN P.INPUT
GAMMA
ENGLISH-14ENGLISH-14
OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Options Menu
The following adjustments and settings are available when OPT. is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. The function indicated (**) are effective on video input mode only, not on RGB input mode, except in the P.IN P. window on RGB input mode.
Table 7. Options Menu
Item Description
VOLUME
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
Volume Adjustment: Reduce VOLUME Increase VOLUME Select Menu Background Color: Select with the and buttons. Select Menu Display Language: Select with the and buttons. Set AUTO OFF: Set 1~99 minutes with the and buttons. The
system automatically enters the standby mode when a signal is not received for the set time. Clear AUTO OFF: Select STOP (0 min.) with the button. When STOP is selected the system does not enter the standby mode even if no signal is received.
SYNC ON G Valid: Select TURN ON with the button. SYNC ON G Invalid: Select TURN OFF with the button.
May not be displayed correctly with some input signals when SYNC ON G is valid. In such cases, remove the signal connector so that no signal is received, set SYNC ON G to invalid, and reconnect the signal.
Set / Crear WHISPER Mode: Press the and button.When the WHISPER is selected, the WHISPER mode is active. In the WHISPER mode, acoustic moise level from the unit is reduced, and brightness level on screen is a little lower.
SETUP INPUT OPT.
VOLUME
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IMAGE
16
ENGLISH
ENGLISH-15
ENGLISH-15
OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
No Signal Menu
The same adjustments and settings are available with the Image and Options menus when the MENU button is pressed during display of the “NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE ON ***” message while no signal is received.
Table 8. No Signal Menu
Item Description
Volume Adjustment: Reduce VOLUME Increase VOLUME
VOLUME
BLANK
MIRROR
START UP
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
When this function is used, audio input is automatically switched to video. The audio input can be switched by moving the DISK PAD left and right during the display of the volume adjustment bar. The volume adjustment bar is displayed by pressing VOLUME or VOLUME button.
Select Blank Screen Color: Select the color with the and buttons.
The image is cleared and the entire screen is displayed in the selected color, when BLANK mode is set with BLANK ON, or when there is no signal for 5 minutes.
Operation Start/Stop: Press the or button. Select Mirror Status: Select the mirror status with the and
buttons.
Operation Start/Stop: Press the or button. Setup Initial Screen Display: Select the TURN ON with the button. Clear Initial Screen Display: Select the TURN OFF with the button.
Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal.
Select Menu Background Color: Select the color with the and buttons.
Operation Start/Stop: Press the or button. Select Menu Display Language: Select the language with the and
buttons.
Operation start/stop: Press the or button. Set AUTO OFF: Set 1~99 minutes with the and buttons. The
system automatically enters the standby mode when a signal is not received for the set time. Clear AUTO OFF: Select the STOP (0 min.) with the button. When the STOP is selected the system does not enter the standby mode even if no signal is received.
Operation Start/Stop: Press the or button. SYNC ON G Valid: Select the TURN ON with the button. SYNC ON G Invalid: Select the TURN OFF with the button.
May not be displayed correctly with some input signals when the SYNC ON G is valid. In such cases, remove the signal connector so that no signal is received, set the SYNC ON G to invalid, and reconnect the signal.
Operation Start/Stop: Press the or button. Set / Crear WHISPER Mode: Press the and button.When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER mode, acoustic moise level from the unit is reduced, and brightness level on screen is a little lower.
VOLUME
BLANK
MIRROR
START UP
MENU COLOR
LANGUAGE AUTO OFF
SYNC ON G
WHISPER
16
ENGLISH-16
MAINTENANCE
MAINTENANCE
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact your dealer before replacing the lamp. For the optional lamp, see the item “Optional Parts” of the Table 12. Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high temperatures.
WARNING A mercury lamp used in this LCD projector is made of glass and has high
internal pressure. The mercury lamp can burst with a big noise due to deterioration resulting from a shock, crack and passage of time, and can end its service life in unlit condition. Lamps also have a considerably different service life and can sometimes end up in burst or turn to unlit condition soon after use. Furthermore, when the lamp is blown up, glass fragments can get scattered around the lamp house and some gas containing mercury inside the lamp can leak out of the projectors air vent.
Handle the lamp with utmost care as it can burst during use if subjected to a shock or impact or if scratched or cracked.
Probability for the burst will increase if the lamp is used for extended period of time or used exceeding the period of replacement. You are advised to follow instructions for lamp replacement as soon as they are given (Refer to Table 9 of Page 20, Table 10 of Page 21). Avoid any reuse of an old lamp (used lamp) since such reuse can result in burst.
In case the lamp gets blown up in a short period of time after use, some electrical failures or troubles other than the lamp itself may be suspected as causes. Under such circumstances, consult the store where you purchased it or a service company.
Should the lamp burst (accompanied by a big bursting noise), perform ventilation sufficiently, and exercise maximum caution not to inhale any gas out of the projectors air vent or not to let it enter your eyes or mouth.
Should the lamp burst (accompanied by a big bursting noise), make absolutely sure to unplug the power cord from the outlet and ask the store where you bought the lamp for immediate replacement. You should not engage in cleanup or replacement of the lamp by yourself since scattered glass fragments can damage the inside of projector or can result in personal injury when you handle it.
When you dispose of any used lamps, be sure to observe and follow local ordinances and regulations of the area or district where they are subjected to disposal. Generally speaking, the lamps are treated similarly as glasses and bottles in most cases, but there are areas or districts where lamps are classified as a separate collection, and so be sure to use caution.
Never use the lamp in a state where the lamp cover is removed.
ENGLISH
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker, after a lamp has been used for a long period of time. Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.
NOTE
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp.
The LAMP indicator is also red when the lamp unit reaches high temperature. Before
ENGLISH-17
MMMMAAAAIIIINNNNTTTTEEEENNNNAAAANNNNCCCCEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
Replacing the Lamp
1. Switch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool.
2. Prepare a new lamp.
3. Check that the projector has cooled sufficiently, and gently turn it upside down.
4. Loosen the two screws as shown in the diagram, and remove the lamp cover.
5. Loosen the two screws, and gently remove the lamp while holding the grips. Touching the inside of the lamp case may result in uneven coloring.
6. Install the new lamp and tighten the two screws firmly. Also steadily push the opposite side of the screwed lamp into the unit.
7. Replace the lamp cover in position and tighten the screw firmly.
8. Gently turn the projector right-side up.
CAUTION Ensure that screws are tightened properly. Screws not tightened fully may result
in injury or accidents.
Do not use the projector with the lamp cover removed.
))
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP indicator is red, or the CHANGE THE LAMP message is displayed, complete the following operation within ten minutes of switching power ON. The power will be turned off automatically in over 10 minutes.
1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP xxxx hr’ message will appear on the lamp timer on the bottom of the screen.
2. Press the MENU button on the remote control transmitter, or the RESET button on the control panel, while the lamp timer is displayed. The ‘LAMP xxxx then appear.
3. Press the and select 0, and wait until the timer display is cleared.
NOTE
when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.
Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always
0 CANCEL’ message will
An air filter is attached to the optional lamp. Replace the filter after replacing the lamp.
ENGLISH-18ENGLISH-18
MMMMAAAAIIIINNNNTTTTEEEENNNNAAAANNNNCCCCEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Air Filter
Replacing the Air Filter
Replace the air filter if contamination cannot be removed, or if it is damaged.
1. Remove the filter lid.
2. Pull and remove the old filter from the filter box.
3. Insert the new filter to the filter box. Push left and right edges of the filter with fingers in order to fit the filter to the box properly. Check that there is no gap between the filter and plastics at top, left and right side edge of the filter.
4. Set the filter lid.
Cleaning the air Filter
The air filter should be cleaned as described below at intervals of approximately 300 hours.
1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
2. Clean the air filter with a vacuum cleaner.
CAUTION Switch power OFF and remove the power cord from the power outlet before beginning maintenance work. Please read the separate SAFETY
INSTRUCTIONS thoroughly to ensure that maintenance is performed correctly.
Replace the air filter if contamination cannot be removed, or if it is damaged. Contact your dealer in such case. For the optional air filter, see the item Optional Parts of the Table 12.
Do not use the equipment with the air filter removed.
When the air filter is clogged with dust etc. the power supply is switched OFF
automatically to prevent the temperature rising inside the projector.
Filter box
Filter Lid
Filter
ENGLISH
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION Switch power OFF and remove the power cord from the power outlet before beginning maintenance work. Please read the separate SAFETY
INSTRUCTIONS thoroughly to ensure that maintenance is performed correctly.
Do not use detergents or chemicals other than those noted above (e.g. benzene or thinners).
Do not use cleaning sprays.
Do not rub with hard materials, or tap the equipment.
NOTE
take place on the projection lens and mirror inside, blurring the screen and reducing your eyesight, but do not worry. The condensation will disappear and the screen will return to a normal condition no sooner than the projector acclimates to the surrounding temperature.
When this projector is brought into a warm room from a cold outdoor, condensation can
ENGLISH-19
ENGLISH-19
TROUBLESHOOTING
TROUBLESHOOTING
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate measures when such a message appears.
Table 9. OSD Message
Message Contents
The message shown at left appears after the lamp has
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN OFF
AFTER ** hr.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL
TURN OFF
AFTER 0 hr.
been used for more than 1300 hours. The lamp is approaching the end of its life. Power is switched OFF automatically when the lamp reaches the end of its life. Prepare a new lamp for
*1)
installation. Always reset the lamp timer after replacing the lamp.
The lamp will reach the end of its life in ** hours. Power will be switched OFF automatically in ** hours. Replace the lamp as shown in P.17~18 Lamp”. Always reset the lamp timer after replacing the lamp.
*1)
The lamp has reached the end of its life. Power will be switched OFF in a few minutes. Switch power OFF immediately and replace the lamp as shown in P.17~18 Lamp”. Always reset the lamp timer after replacing the lamp.
NO INPUT IS DETECTED
ON ***
SYNC IS OUT OF RANGE
ON ***
CHECK THE AIR FLOW
NOTE
every time power is switched ON.
*1) This message is cleared automatically after approximately three minutes, and appears
ENGLISH-20ENGLISH-20
No input signal found. Check signal input connections and signal sources.
The horizontal or vertical frequency of the input signal is not within the specified range. Check the specifications of the equipment and the signal source.
The internal temperature has risen. Switch power OFF, and wait 20 minutes until the equipment cools. Check the following and Switch power ON again. * Are the ventilation openings blocked. * Is the air filter dirty. * Is the ambient temperature in excess of 35°C.
TTTTRRRROOOOUUUUBBBBLLLLEEEESSSSHHHHOOOOOOOOTTTTIIIINNNNGGGG ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Indicators Message
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the appropriate measures.
Table 10. Indicators Message
ENGLISH
STANDBY/ON
indicator
Lights
orange
Blinks
green
Lights
green
Blinks
orange
Lights red
Lights red
Lights red Turns off
LAMP
indicator
Turns off Turns off The Standby mode has been set.
Turns off Turns off Warming up. Please wait.
Turns off Turns off ON. Normal operation possible.
Turns off Turns off Cooling. Please wait.
Lights
red
Blinks
red
TEMP
indicator
Turns off
Turns off
Blinks
red
Contents
Lamp is not lit. The interior of the equipment may be too hot. Switch power OFF, wait 20 minutes until the equipment cools, and check whether the ventilation openings are blocked, whether the air filter is dirty, or whether the ambient temperature exceeds 35 °C. And switch power ON again. Replace the lamp if the same problem occurs.
Lamp or lamp cover is not found, or hasnt been fitted in correctly. Switch power OFF, and wait for 45 minutes until the equipment cools. Check fitting of the lamp and lamp cover, and switch power ON again. Contact your dealer if the same problem occurs again.
The cooling fan is not operating. Switch power OFF, and wait for 20 minutes until the equipment cools. Check for foreign matters in the fan, and switch power ON again. Contact your dealer if the same problem occurs again.
NOTE
automatically for safety reasons, and the indicator is extinguished. Set the power switch to [ wait for 20 minutes until the equipment has cooled sufficiently.
*1) When the internal temperature becomes excessive power is switched OFF
ENGLISH-21
ENGLISH-21
O
] and
TTTTRRRROOOOUUUUBBBBLLLLEEEESSSSHHHHOOOOOOOOTTTTIIIINNNNGGGG ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
Symptom
Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.
Table 11. Symptom
Symptom Possible cause Remedy Page
The power is not turned on.
No video or audio.
The main power switch is not turned on.
The power cord is disconnected.
The main power was disconnected during operation by the power failure and so on.
The input is not correctly set.
No signal input. Connect correctly.
Turn on the main power switch.
Plug the power cord into an AC power outlet.
Turn off the projector with the main power switch (set the power switch to [O]), and wait for about 20 minutes. When the equipment has cooled enough, turn power on.
Use the projector or remote control transmitter to set.
8,9
7,8
))
9
10
Video is present but no audio.
Audio is present but no video.
Colors are pale and color matching is poor.
Images are dark.
Video is blurred.
The projector is not correctly connected.
The volume is set to minimum.
Mute is turned on.
The projector is not correctly connected.
The brightness adjustment knob is rotated fully clockwise.
The lens cap is still attached. Remove the lens cap.
Color density and color matching are not correctly adjusted.
Brightness and contrast are not correctly adjusted.
The lamp is nearing the end of its service life.
WHISPER mode is set. Clear WHISPER mode.
Focus or H PHASE is out of adjustment.
Connect correctly.
Press VOLUME on the remote control or display the menu screen and adjust the volume.
Press the MUTE button.
Connect correctly.
Select BRIGHT with the MENU button and the press the button.
Adjust the video.
Adjust the video.
Replace with a new lamp.
Adjust the focus or H PHASE.
7,8
11,15
11
7,8
12
9
12
12
17
15
9,12
ENGLISH-22ENGLISH-22
SPECIFICATIONS
SPECIFICATIONS
Table 12. Specifications
Item Specification
Product name Liquid crystal projector
Liquid crystal panel
Lens Zoom lens F=2.7 ~ 3.1 f=38.0 ~ 49.0 mm
Lamp 220 W UHB
Speaker 1W
Power supply AC100 ~ 120V, 4.0A / AC220 ~ 240V, 1.8A
Power consumption 360W
Temperature range 0 ~ 35°C (Operating)
Size 250 (W) x 103 (H) x 335 (D) mm
Weight (mass) 5.6 kg
RGB signal input
Video signal input
Signal output
Control functions
Optional Parts
NOTE
Panel size 2.3 cm (0.9 type)
Drive system TFT active matrix
Pixels 1,397,760 pixels (1365 horizontal x 1024 vertical)
Video: Analog 0.7Vp-p, 75terminator (positive)
1
RGB IN
DVI
RGB1
AUDIO IN
VIDEO
S-VIDEO
COMPONENT VIDEO
AUDIO
RGB OUT
AUDIO OUT
CONTROL D-sub 15-pin shrink plug
USB USB jack (B type)
DVI RGB2
L/MONO
H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level
2
D-sub 15-pin shrink jack
TMDS, DC: 150~1200 mV / AC: 1.56 Vp-p TTL Level (Positive/Negative)
200mVrms, 20 k(max. 3.0Vp-p) Stereo mini jack
1.0Vp-p, 75terminator RCA jack
Brightness signal: 1.0Vp-p, 75terminator Color signal: 0.286Vp-p (burst signal), 75terminator Mini DIN 4-pin jack
Y 1.0 Vp-p, 75 Terminator (Positive) CB/PB 0.7 Vp-p, 75 Terminator (Positive) CR/PR 0.7 Vp-p, 75 Terminator (Positive)
200mVrms, 20 k(max. 3.0Vp-p) RCA jack
R
Video: Analog 0.7Vp-p, 75output impedance (positive) H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level D-sub 15-pin shrink jack
200mVrms, output impedance 1 k(max. 3.0Vp-p) Stereo mini jack
Lamp: DT00421 Air Filter: MN04291 * For others, consult your dealer.
This specifications are subject to change without notice.
ENGLISH
ENGLISH-23
ENGLISH-23
WARRANTY AND AFTER-SERVICE
WARRANTY AND AFTER-SERVICE
If a problem occurs with the equipment, first refer to the P.20 “TROUBLESHOOTING” section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.
ENGLISH-24ENGLISH-24
TECHNICAL
1
23
4
5
6
7
89
10
11
1213
1415
TECHNICAL
Dimension Diagram
335
250
103
118.5
Unit : mm
Signal Connector Pin Assignment
1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT)
Pin No Signal Pin No Signal Pin No Signal
1 Video input Red 9 -
2 Video input Green 10 Ground RGB IN 2: -
3 Video input Blue 11 - RGB OUT: -
4 -
5 Ground RGB IN 2: -
6 Ground Red RGB OUT: -
7 Ground Green 13
8 Ground Blue 14 Vertical sync
RGB IN 1: SDA(DDC)
12
H. sync./ Composite sync.
2. Digital Receptacle Connector (DVI)
Pin No Signal Pin No Signal Pin No Signal
1 T.M.D.S. Data 2 - 11 T.M.D.S. Data 1 / 3 Shield 21 -
2 T.M.D.S. Data 2 + 12 - 22 T.M.D.S. Clock Shield
3 T.M.D.S. Data 2 / 4 Shield 13 - 23 T.M.D.S. Clock +
4 - 14 +5V Power 24 T.M.D.S. Clock -
5 - 15
6 DDC Clock 16 Hot-Plug Sense
7 DDC Data 17 T.M.D.S. Data 0 -
8 Analog V. Sync. 18 T.M.D.S. Data 0 +
9 T.M.D.S. Data 1 - 19 T.M.D.S. Data 0 / 5 Shield
10 T.M.D.S. Data 1 + 20 -
Ground (+5V, Analog H/V Sync.)
RGB IN 1: SCL(DDC)
15
123456 78 9 101112131415
17 18 19 20 21 22 23 24
16
3. Mini Din 4-pin Connector (S-VIDEO)
Pin No Signal
Color:0.286Vp-p (NTSC, burst signal),75terminator
1
2 Brightness:1.0Vp-p, 75terminator
3 Ground
4 Ground
0.3Vp-p (PAL/SECAM, burst signal),75terminator
TECHNICAL
TECHNICAL - 1
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Example of computer signal
Resolution
H ××V
720 × 400
640 × 480
640 × 480
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
800 × 600
800 × 600
800 × 600
832 × 624
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1152 × 864
1280 × 960
1280 × 1024
1280 × 1024
1280 × 1024
1600 × 1200
fH (kHz) fV (Hz) Rating Signal mode
37.9 85.0 VESA TEXT
31.5 59.9 VESA VGA (60Hz)
35.0 66.7 Mac13"mode
37.9 72.8 VESA VGA (72Hz)
37.5 75.0 VESA VGA (75Hz)
43.3 85.0 VESA VGA (85Hz)
35.2 56.3 VESA SVGA (56Hz)
37.9 60.3 VESA SVGA (60Hz)
48.1 72.2 VESA SVGA (72Hz)
46.9 75.0 VESA SVGA (75Hz)
53.7 85.1 VESA SVGA (85Hz)
49.7 74.5 Mac16"mode
48.4 60.0 VESA XGA (60Hz)
56.5 70.1 VESA XGA (70Hz)
60.0 75.0 VESA XGA (75Hz)
68.7 85.0 VESA XGA (85Hz)
67.5 75.0 VESA SXGA (75Hz)
60.0 60.0 VESA SXGA (60Hz)
64.0 60.0 VESA SXGA (60Hz)
80.0 75.0 VESA SXGA (75Hz)
91.2 85.0 VESA SXGA (85Hz)
75.0 60.0 VESA UXGA (60Hz)
NOTE
Some computers may have multiple display screen modes. Use of some of these modes
will not be possible with this projector.
• Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer.
• Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above.
• The image might be something wrong with computer by computer on the digital RGB mode. In the case, it is recommended to reduce the resolution and / or reflesh rate.
TECHNICAL - 2
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
DATA
HSYNC
DATA
VSYNC
))
Initial set signals
The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu.
Back porch b
Display interval c
Front porch d
Back porch b
Front porch d
Display interval c
Sync a
Computer /
Signal
TEXT 2.0 3.0 20.3 1.0
VGA (60Hz) 3.8 1.9 25.4 0.6
Mac 13"mode 2.1 3.2 21.2 2.1
VGA (72Hz) 1.3 3.8 20.3 1.0
VGA (75Hz) 2.0 3.8 20.3 0.5
VGA (85Hz) 1.6 2.2 17.8 1.6
SVGA (56Hz) 2.0 3.6 22.2 0.7
SVGA (60Hz) 3.2 2.2 20.0 1.0
SVGA (72Hz) 2.4 1.3 16.0 1.1
SVGA (75Hz) 1.6 3.2 16.2 0.3
SVGA (85Hz) 1.1 2.7 14.2 0.6
Mac 16"mode 1.1 3.9 14.5 0.6
XGA (60Hz) 2.1 2.5 15.8 0.4
XGA (70Hz) 1.8 1.9 13.7 0.3
XGA (75Hz) 1.2 2.2 13.0 0.2
XGA (85Hz) 1.0 2.2 10.8 0.5
1152×864 (75Hz)
1280×960 (60Hz)
1280×1024 (60Hz)
1280×1024 (75Hz)
1280×1024 (85Hz)
1600×1200 (60Hz)
Horizontal signal timing (µs)
a b c d
1.2 2.4 10.7 0.6
1.0 2.9 11.9 0.9
1.0 2.3 11.9 0.4
1.1 1.8 9.5 0.1
1.0 1.4 8.1 0.4
1.2 1.9 9.9 0.4
Sync a
Computer /
Signal
TEXT 3 42 400 1
VGA (60Hz) 2 33 480 10
Mac 13"mode 3 39 480 3
VGA (72Hz) 3 28 480 9
VGA (75Hz) 3 16 480 1
VGA (85Hz) 3 25 480 1
SVGA (56Hz) 2 22 600 1
SVGA (60Hz) 4 23 600 1
SVGA (72Hz) 6 23 600 37
SVGA (75Hz) 3 21 600 1
SVGA (85Hz) 3 27 600 1
Mac 16"mode 3 39 624 1
XGA (60Hz) 6 29 768 3
XGA (70Hz) 6 29 768 3
XGA (75Hz) 3 28 768 1
XGA (85Hz) 3 36 768 1
1152×864 (75Hz)
1280×960 (60Hz)
1280×1024 (60Hz)
1280×1024 (75Hz)
1280×1024 (85Hz)
1600×1200 (60Hz)
Vertical signal timimg (lines)
a b c d
3 32 864 1
3 36 960 1
3 38 1024 1
3 38 1024 1
3 44 1024 1
3 46 1200 1
TECHNICAL
TECHNICAL - 3
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
2
1
4
3
6
5
2
1
4
3
6
5
8
7
10
9
12
11
14
13
15
CLK
DATA
SEL0
RTS
GND
+5V
DATA
GND +5V CLK
2
1
4
3
6
5
1
2
3
4
5
678
9
10
11 12
13
14
15
))
Connection to the Mouse Control
1. PS/2, ADB or Serial Mouse
(1) Turn off the projector and computer, and connect the two units with the appropriate cable. For
PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult
your dealer. (2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector. (3) Turn on the computer.
Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or
(4)
reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4.
2. USB Mouse
(1) Connect the projector and computer with a suitable commercially available USB cable. Consult
your dealer to get the cable, if you need. (2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT
button” of page 4.
NOTE
• Before connecting, read the instruction manuals of the devices to be connected.
• In the case of notebook type computers with an internal pointing device, the mouse control function will not work unless the internal pointing device is disabled. In such case, disable the internal pointing device and change the BIOS setting to select an external mouse before the operations described in (1) to (5) above. Also, some computers may not have a utility program to operate a mouse. Refer to the computer hardware manual for detail.
PS/2 Mouse
CONTROL Terminal
D-sub 15-pin shrink jack
Projector
Computer
TECHNICAL - 4
Mouse jack
Mini DIN 6-pin
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
1
2
3
4
1
2
3
4
+
5V
DATA
+
DATA
GND
+
5V
DATA
+
DATA
GND
1
234
2
1
3
4
2
1
4
3
6
5
2
1
4
3
8
7
10
9
12
11
14
13
15
RTS
GND
+5V
ADB
GND
+5V
(
POWER ON
)
DATA
2
1
4
3
1
2
3
4
5
678
9
10
11 12 13
14
15
2
1
4
3
6
5
2
1
4
3
6
5
8
7
10
9
8
7
9
12
11
14
13
15
RI
CD RD TD
DTR GND DSR
CTS
RTS
RTS
GND
SEL0
TD
21
4
3
6
5
8
9
7
1
2
3
4
5
678
9
10
11 12 13
14
15
))
ADB Mouse
CONTROL Terminal
D-sub 15-pin shrink jack
Serial Mouse
CONTROL Terminal
D-sub 15-pin shrink jack
Projector
Projector
Computer
Mouse jack
Mini DIN 4-pin
Computer
Mouse jack D-sub 9-pin
USB Mouse
USB jack
(B type)
Projector
USB cable
Computer
USB jack
(A type)
TECHNICAL - 5
TECHNICAL
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
1
23
4
5
6
7
89
10
11
1213
1415
1 2 3 4 5 6 7 8 9
10
11
12
13 14
15
RD
TD
GND
SELO
RTS
1 2 3 4 5 6 7 8 9
CD RD TD DTR GND DSR RTS DTS RI
1
2345
67
8
9
))
RS-232C communication
(1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and, after the computer has started up, turn on the projector
power supply.
Projector Computer
Control jack
D-sub 15-pin shrink jack
Communications setting
19200bps, 8N1
1 Protocol
Consist of header (7 bytes) + command data (6 bytes).
2 Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low : Lower byte of CRC flag for command data. CRC_high : Upper byte of CRC flag for command data.
3 Command data
Command data chart
byte_0 byte_1 byte_2 byte_3 byte_4 byte_5
Action Type Setting code
low high low high low high
RS-232C jack
D-sub 9-pin
TECHNICAL - 6
Action (byte_0 - 1)
Action Classification Content
1 SET Change setting to desired value.
2 GET Read projector internal setup value.
4 INCREMENT Increment setup value by 1.
5 DECREMENT Decrement setup value by 1.
6 EXECUTE Run a command.
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’)
from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2
bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+ type (2
bytes) +‘00H’+‘00H’) to the projector. (2) The projector changes the specified setting to the default value. (3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+ type (2 bytes)
+‘00H’+‘00H’) to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+ type (2 bytes)
+‘00H’ + ‘00H’) to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer.
When a command sent by the projector cannot be understood by the computer
When the command sent by the projector cannot be understood, the error command ‘15H’ is returned by the computer. Some times, the projector ignores RS-232C commands during other works. If the error command ‘15H’ is returned, please send the same command again.
When data sent by the projector cannot be practice
When the command sent by the projector cannot be practiced, the the error code ‘1cH’ +‘xxxxH’ is returned. When the data length is greater than indicated by the data length code, the projector will ignore the excess data code. Conversely, when the data length is shorter than indicated by the data length code, an error code will be returned to the projector.
NOTE
data.
Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data.
• Commands are not accepted during warm-up.
Operation cannot be guaranteed when the projector receives an undefined command or
TECHNICAL - 7
TECHNICAL
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Command data chart
Names Operation type Header
Red BE EF 03 06 00 3B D3 01 00 00 30 00 00
Orange BE EF 03 06 00 AB D2 01 00 00 30 01 00
Green BE EF 03 06 00 5B D2 01 00 00 30 02 00
Blank Color
Mirror
Freeze
Menu Color
Startup
Language
Set
Set
Set
Set
Set
Set
Blue BE EF 03 06 00 CB D3 01 00 00 30 03 00
Purple BE EF 03 06 00 FB D1 01 00 00 30 04 00
White BE EF 03 06 00 6B D0 01 00 00 30 05 00
Black BE EF 03 06 00 9B D0 01 00 00 30 06 00
Get BE EF 03 06 00 08 D3 02 00 00 30 00 00
Normal BE EF 03 06 00 C7 D2 01 00 01 30 00 00
H Inverse BE EF 03 06 00 57 D3 01 00 01 30 01 00
V lnverse BE EF 03 06 00 A7 D3 01 00 01 30 02 00
H&V Inverse BE EF 03 06 00 37 D2 01 00 01 30 03 00
Get BE EF 03 06 00 F4 D2 02 00 01 30 00 00
Normal BE EF 03 06 00 83 D2 01 00 02 30 00 00
Freeze BE EF 03 06 00 13 D3 01 00 02 30 01 00
Get BE EF 03 06 00 B0 D2 02 00 02 30 00 00
Red BE EF 03 06 00 7F D3 01 00 03 30 00 00
Orange BE EF 03 06 00 EF D2 01 00 03 30 01 00
Green BE EF 03 06 00 1F D2 01 00 03 30 02 00
Blub BE EF 03 06 00 8F D3 01 00 03 30 03 00
Purple BE EF 03 06 00 BF D1 01 00 03 30 04 00
Transparent BE EF 03 06 00 2F D0 01 00 03 30 05 00
Gray BE EF 03 06 00 DF D0 01 00 03 30 06 00
Get BE EF 03 06 00 4C D3 02 00 03 30 00 00
Turn ON BE EF 03 06 00 0B D2 01 00 04 30 00 00
Turn OFF BE EF 03 06 00 9B D3 01 00 04 30 01 00
Get BE EF 03 06 00 38 D2 02 00 04 30 00 00
English BE EF 03 06 00 F7 D3 01 00 05 30 00 00
Français BE EF 03 06 00 67 D2 01 00 05 30 01 00
Deutsch BE EF 03 06 00 97 D2 01 00 05 30 02 00
Español BE EF 03 06 00 07 D3 01 00 05 30 03 00
Italiano BE EF 03 06 00 37 D1 01 00 05 30 04 00
Norsk BE EF 03 06 00 A7 D0 01 00 05 30 05 00
Nederlands BE EF 03 06 00 57 D0 01 00 05 30 06 00
Português BE EF 03 06 00 C7 D1 01 00 05 30 07 00
Japanese BE EF 03 06 00 37 D4 01 00 05 30 08 00
Get BE EF 03 06 00 C4 D3 02 00 05 30 00 00
CRC Action Type Setting code
Command data
TECHNICAL - 8
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Command data chart
Names Operation type Header
Get BE EF 03 06 00 7C D2 02 00 07 30 00 00
Magnify
Auto off
Brightness Reset Execute BE EF 03 06 00 58 D3 06 00 00 70 00 00
Contrast Reset Execute BE EF 03 06 00 A4 D2 06 00 01 70 00 00
V.Position Reset Execute BE EF 03 06 00 E0 D2 06 00 02 70 00 00
H.Position Reset Execute BE EF 03 06 00 IC D3 06 00 03 70 00 00
H.Size Reset Execute BE EF 03 06 00 68 D2 06 00 04 70 00 00
Color Balance R Reset Execute BE EF 03 06 00 94 D3 06 00 05 70 00 00
Color Balance B Reset Execute BE EF 03 06 00 D0 D3 06 00 06 70 00 00
Sharpness Reset Execute BE EF 03 06 00 C4 D0 06 00 09 70 00 00
Color Reset Execute BE EF 03 06 00 80 D0 06 00 0A 70 00 00
Tint Reset Execute BE EF 03 06 00 7C D1 06 00 0B 70 00 00
Keystone_VReset
Auto Execute BE EF 03 06 00 91 D0 06 00 0A 20 00 00
Blank on/off
Error Status Get
Power
Input Source
Volume
Increment BE EF 03 06 00 1A D2 04 00 07 30 00 00
Decrement BE EF 03 06 00 CB D3 05 00 07 30 00 00
Get BE EF 03 06 00 08 86 02 00 10 31 00 00
Increment BE EF 03 06 00 6E 86 04 00 10 31 00 00
Decrement BE EF 03 06 00 BF 87 05 00 10 31 00 00
Execute BE EF 03 06 00 08 D0 06 00 0C 70 00 00
off BE EF 03 06 00 FB D8 01 00 20 30 00 00
Set
on BE EF 03 06 00 6B D9 01 00 20 30 01 00
Get BE EF 03 06 00 C8 D8 02 00 20 30 00 00
BE EF 03 06 00 D9 D8 02 00 20 60 00 00
(Example of Return) 00 00 01 00 02 00 03 00 (Normal) (Cover-error) (Fan-error) (Lamp-error)
04 00 05 00 06 00 (reserved) (reserved) (Lamp-Time-over)
OFF
Set
ON
Get
RGB1 BE EF 03 06 00 FE D2 01 00 00 20 00 00
RGB2 BE EF 03 06 00 3E D0 01 00 00 20 04 00
DVI BE EF 03 06 00 0E D2 01 00 00 20 03 00
Set
Video BE EF 03 06 00 6E D3 01 00 00 20 01 00
SVideo BE EF 03 06 00 9E D3 01 00 00 20 02 00
Component
Get BE EF 03 06 00 CD D2 02 00 00 20 00 00
Get BE EF 03 06 00 31 D3 02 00 01 20 00 00
Increment BE EF 03 06 00 57 D3 04 00 01 20 00 00
Decrement BE EF 03 06 00 86 D2 05 00 01 20 00 00
BE EF 03 06 00 2A D3 01 00 00 60 00 00 BE EF 03 06 00 BA D2 01 00 00 60 01 00
BE EF 03 06 00 19 D3 02 00 00 60 00 00
BE EF 03 06 00 AE D1 01 00 00 20 05 00
CRC Action Type Setting code
Command data
TECHNICAL - 9
TECHNICAL
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Command data chart
Names Operation type Header
Normal BE EF 03 06 00 46 D3 01 00 02 20 00 00
Mute
Brightness
Contrast
Color
Balance R
Color
Balance B
Keystone_V
Keystone_H
Aspect
Display
Position at
16 : 9 or Small
V.Position
H.Position
H.Size
H.Phase
Set
Set
Set
Mute BE EF 03 06 00 D6 D2 01 00 02 20 01 00
Get BE EF 03 06 00 75 D3 02 00 02 20 00 00
Get BE EF 03 06 00 89 D2 02 00 03 20 00 00
Increment BE EF 03 06 00 EF D2 04 00 03 20 00 00
Decrement BE EF 03 06 00 3E D3 05 00 03 20 00 00
Get BE EF 03 06 00 FD D3 02 00 04 20 00 00
Increment BE EF 03 06 00 9B D3 04 00 04 20 00 00
Decrement BE EF 03 06 00 4A D2 05 00 04 20 00 00
Get BE EF 03 06 00 01 D2 02 00 05 20 00 00
Increment BE EF 03 06 00 67 D2 04 00 05 20 00 00
Decrement BE EF 03 06 00 B6 D3 05 00 05 20 00 00
Get BE EF 03 06 00 45 D2 02 00 06 20 00 00
Increment BE EF 03 06 00 23 D2 04 00 06 20 00 00
Decrement BE EF 03 06 00 F2 D3 05 00 06 20 00 00
Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00
Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00
Decrement BE EF 03 06 00 0E D2 05 00 07 20 00 00
Get BE EF 03 06 00 E9 D0 02 00 0B 20 00 00
Increment BE EF 03 06 00 8F D0 04 00 0B 20 00 00
Decrement BE EF 03 06 00 5E D1 05 00 0B 20 00 00
4:3, Full BE EF 03 06 00 9E D0 01 00 08 20 00 00
16:9 BE EF 03 06 00 0E D1 01 00 08 20 01 00
Small BE EF 03 06 00 FE D1 01 00 08 20 02 00
Real BE EF 03 06 00 6E D0 01 00 08 20 03 00
Get BE EF 03 06 00 AD D0 02 00 08 20 00 00
Default BE EF 03 06 00 62 D1 01 00 09 20 00 00
Bottom BE EF 03 06 00 F2 D0 01 00 09 20 01 00
Top BE EF 03 06 00 02 D0 01 00 09 20 02 00
Get BE EF 03 06 00 51 D1 02 00 09 20 00 00
Get BE EF 03 06 00 0D 83 02 00 00 21 00 00
Increment BE EF 03 06 00 6B 83 04 00 00 21 00 00
Decrement BE EF 03 06 00 BA 82 05 00 00 21 00 00
Get BE EF 03 06 00 F1 82 02 00 01 21 00 00
Increment BE EF 03 06 00 97 82 04 00 01 21 00 00
Decrement BE EF 03 06 00 46 83 05 00 01 21 00 00
Get BE EF 03 06 00 B5 82 02 00 02 21 00 00
Increment BE EF 03 06 00 D3 82 04 00 02 21 00 00
Decrement BE EF 03 06 00 02 83 05 00 02 21 00 00
Get BE EF 03 06 00 49 83 02 00 03 21 00 00
Increment BE EF 03 06 00 2F 83 04 00 03 21 00 00
Decrement BE EF 03 06 00 FE 82 05 00 03 21 00 00
CRC Action Type Setting code
Command data
TECHNICAL - 10
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Command data chart
Names Operation type Header
Get BE EF 03 06 00 F1 72 02 00 01 22 00 00
Sharpness
Color
Tint
Video Format
Progressive
Black
HDTV
PinP Size
Increment BE EF 03 06 00 97 72 04 00 01 22 00 00
Decrement BE EF 03 06 00 46 73 05 00 01 22 00 00
Get BE EF 03 06 00 B5 72 02 00 02 22 00 00
Increment BE EF 03 06 00 D3 72 04 00 02 22 00 00
Decrement BE EF 03 06 00 02 73 05 00 02 22 00 00
Get BE EF 03 06 00 49 73 02 00 03 22 00 00
Increment BE EF 03 06 00 2F 73 04 00 03 22 00 00
Decrement BE EF 03 06 00 FE 72 05 00 03 22 00 00
Auto BE EF 03 06 00 9E 75 01 00 00 22 0A 00
NTSC BE EF 03 06 00 FE 71 01 00 00 22 04 00
PAL BE EF 03 06 00 6E 70 01 00 00 22 05 00
Set
Set
Set
Set
Set
SECAM BE EF 03 06 00 6E 75 01 00 00 22 09 00
NTSC 4.43 BE EF 03 06 00 5E 72 01 00 00 22 02 00
M-PAL BE EF 03 06 00 FE 74 01 00 00 22 08 00
N-PAL BE EF 03 06 00 0E 71 01 00 00 22 07 00
Get BE EF 03 06 00 0D 73 02 00 00 22 00 00
off BE EF 03 06 00 4A 72 01 00 07 22 00 00
TV BE EF 03 06 00 DA 73 01 00 07 22 01 00
FILM BE EF 03 06 00 2A 73 01 00 07 22 02 00
Get BE EF 03 06 00 79 72 02 00 07 22 00 00
off BE EF 03 06 00 5E 71 01 00 08 22 00 00
on BE EF 03 06 00 CE 70 01 00 08 22 01 00
Get BE EF 03 06 00 6D 71 02 00 08 22 00 00
1080i BE EF 03 06 00 F2 73 01 00 05 22 00 00
1035i BE EF 03 06 00 62 72 01 00 05 22 01 00
Get BE EF 03 06 00 C1 73 02 00 05 22 00 00
off BE EF 03 06 00 FE 22 01 00 00 23 00 00
Large BE EF 03 06 00 6E 23 01 00 00 23 01 00
Small BE EF 03 06 00 9E 23 01 00 00 23 02 00
Get BE EF 03 06 00 Cd 22 02 00 00 23 00 00
Command data
CRC Action Type Setting code
TECHNICAL - 11
TECHNICAL
TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))
))
Command data chart
Names Operation type Header
Upper left BE EF 03 06 00 02 23 01 00 01 23 00 00
Upper right BE EF 03 06 00 92 22 01 00 01 23 01 00
Set
PinP Position
PinP Audio ch
PinP Input
Sync on G
WHISPER
GAMMA
bottom left BE EF 03 06 00 62 22 01 00 01 23 03 00
bottom right BE EF 03 06 00 F2 23 01 00 01 23 02 00
Get BE EF 03 06 00 31 23 02 00 01 23 00 00
Set
Set
Set
Set
Set
RGB BE EF 03 06 00 BA 22 01 00 03 23 00 00
Video BE EF 03 06 00 2A 23 01 00 03 23 01 00
Get BE EF 03 06 00 89 22 02 00 03 23 00 00
Video BE EF 03 06 00 D6 22 01 00 02 23 01 00
S-Video BE EF 03 06 00 26 22 01 00 02 23 02 00
Component BE EF 03 06 00 16 20 01 00 02 23 05 00
Get BE EF 03 06 00 75 23 02 00 02 23 00 00
off BE EF 03 06 00 CB D0 01 00 08 30 01 00
on BE EF 03 06 00 5B D1 01 00 08 30 00 00
Get BE EF 03 06 00 68 D1 02 00 08 30 00 00
NORMAL BE EF 03 06 00 3B 23 01 00 00 33 00 00
WHISPER BE EF 03 06 00 AB 22 01 00 00 33 01 00
Get BE EF 03 06 00 08 23 02 00 00 33 00 00
NORMAL BE EF 03 06 00 C7 F0 01 00 A1 30 00 00
CINEMA BE EF 03 06 00 57 F1 01 00 A1 30 01 00
DYNAMIC BE EF 03 06 00 A7 F1 01 00 A1 30 02 00
Get BE EF 03 06 00 F4 F0 02 00 A1 30 00 00
Command data
CRC Action Type Setting code
TECHNICAL - 12
REGULATORY NOTICES
REGULATORY NOTICES
FCC Statement Warning
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that the following conditions are met. The cables may have to be used with the core set to the projector side. Use the cables which are included with the projector or specified.
Core
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
For the Customers in CANADA
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.
Pour les utilisateurs au Canada
AVIS: Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
REGULATORY NOTICES - 1
LEGAL INFORMATION
FIVE-YEAR LIMITED WARRANTY
This Dukane LCD projector is warranted to the original purchaser for a period of five (5) years from the original purchase date - in normal use and service ­against defects in material and workmanship. DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
During the warranty period, Dukane Corporation will repair or replace (at the manufacturer's option) any such defective parts (except for the lamp, which is subject to whatever warranties the manufacturer may provide) without charge to the purchaser for parts or labor when the product is returned, prepaid and insured, with proof-of-purchase date. This remedy is void if the product has been damaged by accident, unreasonable use, neglect, improper service or other causes not arising out of defects in material or workmanship.
Dukane Corporation disclaims all liability for incidental or consequential damage of any kind, including all damages arising out of any interruptions in operation of the product and all damages to software.
No person, firm, or representative is authorized to assume any obligation or to make any warranty on behalf of the Dukane Corporation other than as stated above.
THIS LIMITED WARRANTY IS VALID FOR U.S.A AND CANADA. FOR OTHER LOCATIONS, LOCAL WARRANTIES APPLY.
LAMP REPLACEMENT SERVICE & REPAIR POLICY & PROCEDURE
For service and parts, contact the Dukane AV Service Department at 1 (800) 676-2487 within the USA or 1 (630) 584-2300 worldwide. If you would like to send a facsimile (FAX), dial 1 (630) 584-5156 worldwide.
When requesting warranty service, please have the sales receipt available along with the model name and serial number.
If it becomes necessary to return the projector, use the original packing material and box (if retained) or pack securely. Dukane Corporation will not be liable for any pick-up or delivery charges or any expenses incurred for service calls or service supplied by anyone other than the Dukane AV Service Department.
Dukane Corporation Audio Visual Products Division 2900 Dukane Drive St. Charles, IL 60174-3395 E-mail: avsales@dukane.com
Audio Visual Products
Phone: (630) 584-2300
Orders: (800) 676-2485
Information: (800) 676-2486
Fax: (630) 584-5156
Parts & Service: (800) 676-2487
Fax: (630) 584-0984
Part # 401-601-00
Loading...