Dukane 28A8909 User Manual

Progressive Scan

Liquid Crystal Projector

Model

28A8909

User's Manual

ENGLISH

Liquid Crystal Projector

USER'S MANUAL

USER'S MANUAL

ENGLISH-1

Thank you for purchasing this liquid crystal projector.

CONTENTS

CONTENTS

Page

FEATURES .......................................2

BEFORE USE ...................................2

Contents of Package ..............................2

Part Names.............................................3

Loading the Batteries..............................5

INSTALLATION ................................6

Installation of the Projector and Screen

........6

Angle Adjustment ...................................6

Cabling ...................................................7

Power Connection ..................................8

Example of System Setup ......................8

Plug & Play.............................................8

OPERATIONS...................................9

Power On...................................................9

Power Off

................................................9

Basic Operation....................................10

Setup Menu ..........................................12

Input Menu............................................13

Image Menu..........................................14

Options Menu .......................................15

No Signal Menu....................................16

MAINTENANCE ..............................17

Lamp.....................................................17

Air Filter ................................................19

Other Maintenance...............................19

Page

TROUBLESHOOTING ....................20

OSD Message ......................................20

Indicators Message ..............................21

Symptom ..............................................22

SPECIFICATIONS...........................23

WARRANTY AND AFTER-SERVICE

......24

.......................................................................................

TABLES

Table 1. Installation Reference.................6

Table 2. Cabling .......................................7

Table 3. Basic Operations ......................10

Table 4. Setup Menu ..............................12

Table 5. Input Menu................................13

Table 6. Image Menu..............................14

Table 7. Options Menu ...........................15

Table 8. No Signal Menu........................16

Table 9. OSD Message ..........................20

Table 10. Indicator Message ..................21

Table 11. Symptom ................................22

Table 12. Specifications .........................23

.......................................................................................

For "TECHNICAL" and "REGULATORY
NOTICE", see the end of this manual.

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual

• The reproduction, transmission or use of this document or contents is not permitted without
express written authority.

TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of
International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of
Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard
Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the
trademarks and registered trademarks of all companies, even when not mentioned.

NOTE

WARNING • Please read the accompanying manual “SAFETY

INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.

ENGLISH-2

FEATURES

FEATURES

This liquid crystal projector is used to project various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space is required for installation and large images can
easily be realized.

Outstanding Brightness

The UHB lamp and high-efficiency optical system assure a high level of brightness.

Partial Magnification Function

Interesting parts of images can be magnified for closer viewing.

Distortion Correction Function

Distortion-free images are quickly available.

BEFORE USE

BEFORE USE

Contents of package

Make sure all of the following items are included in the package. If anything is missing, please
contact your dealer.

• Keep the original packing material for future reshipment.

NOTE

Projector

User’s Manual

(this manual)

Safety Instructions

Power Cord

(US Type)

Power Cord

(UK Type)

Power Cord

(Europe Type)

RGB Cable Video/Audio Cable

(with white lead)

Mouse cable

(PS/2)

Remote Control

Transmitter

Batteries

for Remote Control

Transmitter

Component

Video Cable

(with green lead)

(in this manual)

VIDEO

STANDBY/ON

LASER

RGB

BLANK

AUTO

MENU

POSITION

MENU SELECT

RESET

PinP

FREEZE

VOLUME

MAGNIFY

OFF

MUTE

ZOOMFOCUS

ENGLISH-3

BBBBEEEEFFFFOOOORRRREEEE UUUUSSSSEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

ENGLISH

Part Names

Control Panel

(Refer to P.9 "OPERATIONS")

Front/Right View

Rear/Left View

Terminal Panel

(Refer below)

Terminal
Panel

DIGTAL Terminal

S-VIDEO Terminal

VIDEO Terminal

AUDIO(MONO)/L

Terminal

AUDIO R Terminal

USB Terminal

ZOOM Button

MUTE Button

STANDBY/ON Button

LAMP Indicator

POWER Indicator

FOCUS Button

INPUT Button

MENU Button

RESET Button

TEMP Indicator

Remote Control Sensor

Lens

Foot Adjuster

Lens Cap

Control Panel

Ventilation Openings
(exhaust)

Carrying Handle

Air Filter and Intake
for the Cooling Fan

Foot Adjuster

Remote Control Sensor

Speaker

Power Switch

AC Inlet

(to Power Cord)

RGB IN 1 Terminal
RGB IN 2 Terminal

RGB OUT Terminal

CONTROL Terminal
AUDIO IN RGB1 Terminal

AUDIO IN RGB2 Terminal
AUDIO OUT Terminal

COMPONENT VIDEO
Y Terminal
C

B/PB Terminal

C

R/PR Terminal

ZOOM

MUTE INPUT

STANDBY/ON

MENU

POWER TEMPLAMP

FOCUS

RESET

DIGTAL

S-VIDEO

COMPO

VIDEO

(MONO)/L

AUDIO

R

USB

RGB IN 2

NENT

VIDEO

RGB OUT

CONTROL

AUDIO IN AUDIO

C

B/PB

CR/PR

RGB 1
DIGITAL

OUT

RGB 2

ENGLISH-4

BBBBEEEEFFFFOOOORRRREEEE UUUUSSSSEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Part Names (continued)

S

T

A

N

D

B

Y

/O

N

LASER

VIDEO

BLANK

RGB

AUTO

MENU

MENU SELECT

POSITION

R

E

SET

FR

EEZE

MAGNIFY

PinP

OFF

VOLUME

MUTE

ZOOM

FOCUS

REMOTE CONTROL TRANSMITTER

(Refer to P.9 "OPERATIONS")

To prevent any malfunction;

• Do not give the remote control transmitter any physical impact. Take care not to drop.

• Do not place the heavy objects on the remote control transmitter.

• Do not wet the remote control transmitter or place it on any wet object.

• Do not place the remote control transmitter close to the cooling fan of the projector.

• Do not disassemble the remote control transmitter in case of malfunction. Please bring it to the

service station.

NOTE

STANDBY/ON Button

LASER Button

BLANK Button

Disk Pad

Used to operate the
mouse shift function and
left click function.

AUTO Button

MENU Button

MENU SELECT Button

Used to click the left
mouse button.

, , , Button

Used to operate the
mouse shift function.

MAGNIFY Button

VIDEO Button

RGB Button

MOUSE / RIGHT Button

Used to click the right
mouse button.

RESET Button

Used to click the right
mouse button.

VOLUME Button

FREEZE Button

MUTE Button

POSITION Button

ZOOM Button

These functions works when the mouse control function is activated. Remember, the POSITION,

BLANK ON and MENU ON functions disable the mouse control function.

WARNING • The laser pointer of the remote control transmitter is used in

place of a finger or rod. Never look directly into the laser beam outlet or point
the laser beam at other people. The laser beam can cause vision problems.

FOCUS Button

PinP Button

CAUTION

LASER RADIATION­DO NOT STARE INTO BEAM

WAVE LENGTH: 650nm
MAX . OUTPUT: 1mW

CLASS 2 LASER PRODUCT

RADIAZIONI LASER
NON GUARDARE NEL RAGGIO LUCE
APPARECCHIO LASER DI CLASSE 2
RAYONNEMENT LASER
NE PAS REGARDER DANS
LE FAISCEAU APPAREIL
A LASER DE CLASSE 2
LASER-STRAHLUNG
NICHT IN DEN STRAHL
BLICKEN LASER KLASSE2

MANUFACTURED

PLACE OF
MANUFACTURER:A
MADE IN JAPAN

IEC60825-1:1993+A1:1997

ENGLISH-5

BBBBEEEEFFFFOOOORRRREEEE UUUUSSSSEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

ENGLISH

Loading the Batteries

Install the AA batteries into the remote control
transmitter.

1. Remove the battery cover.
Push the knob while lifting up the battery cover.

2. Load the batteries.
Make sure the plus and minus poles are correctly
oriented.

3. Close the battery cover.

1

2

Replace the batteries when remote control transmitter operation becomes difficult.

NOTE

CAUTION • Use only the specified batteries with this remote control
transmitter. Also, do not mix new and old batteries. This could cause in

battery cracking or leakage, which could result in fire or personal injury.

• When loading the batteries, make sure the plus and minus terminals are
correctly oriented as indicated in the remote control transmitter. Incorrect
orientation could cause battery cracking or leakage, which could result in
personal injury or pollution of the surrounding environment.

• When you dispose the battery, you obey the law in the relative area or country.

• Keep the battery away from children and pets.

• When not to be used for an extended period, remove the batteries from the

remote control transmitter.

ENGLISH-6

INSTALLATION

INSTALLATION

Installation of the Projector and Screen

Refer to the drawing and table below for determining of the screen size and projection distance.

Top View

Side View

Screen size
[inches (m)]

a [inches (m)]

b

[inches (cm)]

Min. Max.
40 (1.0) 55 (1.4) 73 (1.9) 1 (3)
60 (1.5) 85 (2.2) 114 (2.9) 2 (4)
80 (2.0) 114 (2.9) 151 (3.8) 2 (6)

100 (2.5) 144 (3.7) 191 (4.9) 3 (7)
120 (3.0) 176 (4.5) 231 (5.9) 3 (9)
150 (3.8) 220 (5.6) 282 (7.2) 4 (11)
200 (5.0) 291 (7.4) 386 (9.8) 6 (15)

Angle Adjustment

Use the foot adjusters on the bottom of the
projector to adjust the projection angle. It is
variable within 0˚ to 9˚ approximately.

1. Lift up the front side of the projector, and
pressing the foot adjuster button, adjust the
projection angle.

2. Release the button to lock at the angle to be
fixed.

3. Make the foot adjusters screw for fine
adjustment. Do not force the adjusters to make
screw. This could damage the adjusters or
cause the lock to fail.

Foot Adjusters

The projection distances shown in the table below
are for full size (1024 x 768 dots).

a: Distance from the projector to the screen. (±10%)
b: Distance from the lens center to the bottom of the

screen. (±10%)

Table 1. Installation Reference

b

a

Lens center

Screen

CAUTION • Install the projector in a suitable environment according to
instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this

manual.

• Please basically use liquid crystal projector at the horizontal position.

If you use
liquid crystal projector by the lens up position, the lens down position and the side up
position, this may cause the heat inside to build up and become the cause of damage.
Be especially careful not to install it with ventilation holes blocked.

• Do not install LCD projector in smoke effected environment. Smoke residue may
buildup on critical parts (i.e.LCD panel, Lens Assy etc.).

CAUTION • Do not release the foot adjuster button unless the projector is
being held; otherwise, the projector could overturn or the fingers could get

caught and cause personal injury.

Variable within the range of approximately 0° - 9°

ENGLISH-7

ENGLISH

IIIINNNNSSSSTTTTAAAALLLLLLLLAAAATTTTIIIIOOOONNNN ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

• Before connecting, read instruction manuals of the devices to be connected, and make sure that the

projector is compatible with the device.

• Secure the screws on the connectors and tighten.

• For some RGB input modes, the optional Mac adapter is necessary.

• To select the digital RGB input, the comuter may need some settings. See the manuals of the computer for

details.

• Some computers may have multiple display screen modes. Use of some of these modes will not be possible
with this projector.

• Refer to the “TECNICAL” section for the pin assign of connectors and RS-232C communication data.

• When the DIGITAL terminal is used, the RGB OUT terminal may not function.

NOTE

CAUTION • Incorrect connecting could result in fire or electrical shock.
Please read this manual and the separate “SAFETY INSTRUCTIONS”.

• Before connecting, turn off to all devices to be connected, except for the USB
cable.

• The cables may have to be used with the core set to the projector side. Use the
cables which are included with the projector or specified.

Cabling

Refer to the table below for connecting each terminal of the projector to each device.

Table 2. Cabling

Function Terminal Cable

Analog RGB input

RGB IN 1

Accessory RGB cable or optional RGB
cable with D-sub 15-pin shrink jack and
inch thread screws

RGB IN 2

Analog RGB output RGB OUT

Digital RGB input DIGITAL

Optional digital RGB cable with inch thread
screws

Audio input
(from the computer)

AUDIO IN [RGB 1] / [DIGITAL]

(interlocked with RGB IN 1 or
DIGITAL)

Optional audio cable with stereo mini jack

AUDIO IN [RGB 2]

(interlocked with RGB IN 2)

PS/2 mouse control

CONTROL

Accessory PS/2 mouse cable

ADB mouse control Optional ADB mouse cable

Serial mouse control Optional Serial mouse cable

RS-232C communication Optional RS-232C cable
USB mouse control USB Optional USB cable

S-video input S-VIDEO

Optional S-video cable with mini DIN 4-pin
jack

Video input VIDEO Accessory video/audio cable

Component video input

COMPONENT VIDEO Y

Accessory component video cableCOMPONENT VIDEO CB/PB

COMPONENT VIDEO CR/PR

Audio input
(from video equipment)

AUDIO (MONO)/L

Accessory video/audio cable or optional
audio cable with RCA jack

AUDIO R

Audio output AUDIO OUT Optional audio cable with stereo mini jack

Example of system setup

S-Video Tape
Recorder

Computer (desktop type)

Computer

(notebook type)

• When connecting with notebook computer, set to valid the RGB external image output
(setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of
the notebook for more information.

Plug & Play

This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer
that is VESA DDC (Display Data Channel) compatible.
Please use this function by connecting the accessory RGB cable with RGB IN 1 terminal (DDC
1/2B compatible), or by connecting an optional digital RGB cable with DIGITAL terminal (DDC
2B compatible). Plug & play may not operate by other connecting.

• Plug & play is a system configured with peripheral equipment including a computer and
display, and an operating system.

• This projector is recognized as a plug & play monitor. Use the standard display drivers.

• Plug & play may not operate by the computer to connect. Plug & play will not operate in the

connection with Apple computer.

NOTE

NOTE

ENGLISH-8

IIIINNNNSSSSTTTTAAAALLLLLLLLAAAATTTTIIIIOOOONNNN ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Power Connection

Use the correct one of the enclosed power cords depending on the power outlet to be used.
Connect the AC inlet of the projector to the power outlet firmly by the power cord.

AC Inlet

Power Cord

Power outlet

Speaker
with
amplifier

Display
Monitor

CAUTION • Be carful in handling the power

cord according to instructions of the
accompanying manual "SAFETY INSTRUCTIONS"
and this manual.

• Connect the power cord firmly. Avoid using a
loose, unsound outlet or contact failure.

Computer

(desktop type)

DVD Player

DIGTAL

RGB IN 2

S-VIDEO

COMPO

NENT
VIDEO

VIDEO

(MONO)/L

AUDIO

R

USB

RGB OUT

AUDIO IN AUDIO

B/PB

C

CR/PR

DIGITAL

RGB 2

RGB 1

CONTROL

OUT

ENGLISH-9

ENGLISH

ENGLISH-9

OPERATIONS

OPERATIONS

Power ON

1. Check that the power cord is connected correctly.

2. Set the power switch to [ | ]. The standby mode is selected, and the POWER indicator is turned to
orange.

3. Press the STANDBY/ON button on the control panel or the remote control transmitter.
Warm-up begins and the POWER indicator blinks in green.

4. The POWER indicator ceases blinking and turns to green when power is on. Remove the lens
cap.

5. Adjust picture size using the ZOOM button.

6. Adjust focus using the FOCUS button .

Power OFF

1. Press the STANDBY/ON button on the control panel or the remote control transmitter for
approximately two second. The projector lamp is extinguished and lamp cooling begins. The
POWER indicator blinks orange during lamp cooling. Pressing the STANDBY/ON button
has no effect while the POWER indicator is blinking.

2. The system assumes the Standby mode when cooling is complete, and the POWER indicator
ceases blinking and changes to orange. Check that the indicator is orange and set the Power
switch to [

O

].

3. The POWER indicator is extinguished when power is off. Attach the lens cap.

Power Switch

Lens cap

STANDBY/ON Button

POWER Indicator

STANDBY/

ON Button

ZOOM button

FOCUS button

• Except in emergencies, do not turn off unless the POWER indicator is orange as it will

reduce the life of the projector lamp.

• To prevent any troble, turn on/off the projector when the computer or video tape recorder is OFF.

Providing a RS-232C cable is connected, turn on the computer before the projector.

NOTE

WARNING

• Please read this manual, and the separate “SAFETY

INSTRUCTIONS” thoroughly before using the equipment. Always ensure that

the equipment is used safely.

FOCUS button

ZOOM button

STANDBY/ON

BLANK

AUTO

MENU

MENU SELECT

PinP

MAGNIFY

LASER

FREEZE

OFF

ZOOMFOCUS

VIDEO

RGB

POSITION

RESET

VOLUME

MUTE

ENGLISH-10ENGLISH-10

OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Basic Operation

The basic operations shown in Table 3 is performed from the supplied remote control transmitter or
the projector control panel. Items indicated by (*) may be used from the control panel.

Table 3 . Basic Operation

Item Description

INPUT
SELECT

Select Input Signal (*) : Press the INPUT button.

RGB IN 1 → RGB IN 2 → DIGITAL
→ VIDEO → S-VIDEO → COMPONENT VIDEO (→ RGB IN 1)

Select RGB Input : Press the RGB button.

VIDEO/S-VIDEO/COMPONENT VIDEO → RGB IN 1/RGB IN 2/DIGITAL
RGB IN 1 → RGB IN 2 → DIGITAL (→ RGB IN 1)

Select Video Input : Press the VIDEO button.

RGB IN 1/RGB IN 2/DIGITAL → VIDEO/S-VIDEO/COMPONENT VIDEO
VIDEO → S-VIDEO → COMPONENT VIDEO (→ VIDEO)

• The selected signal name is displayed for approximately 3 seconds when the input
signal is changed.

POSITION

Set/Clear Position Adjustment Mode : Press the POSITION button.

The [ ] icon is displayed in the POSITION mode.

Image Position Adjustment: Press the , , and buttons in the
POSITION mode.

• Valid only in the MAGNIFY mode with a video signal is input.

• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the

POSITION mode is cleared automatically.

• , , and

buttons may operate as the mouse control button. Refer to page 4.

RESET (*)

Initialise Each Item : Select an item and press the RESET button.
Initialise Position Adjustment : Press the RESET button and the

POSITION mode. This function is valid only when RGB signal is input.

• Valid except for the VOLUME, LANGUAGE and H PHASE.

• The RESET button may operate as the mouse control button. Refer to page 4.

MAGNIFY

Set MAGNIFY Mode : Press the MAGNIFY button.
Move Magnified Area : Run the POSITION in the MAGNIFY mode.
Adjust Magnification : Press the MAGNIFY / button in MAGNIFY

mode.
Clear MAGNIFY Mode : Press the MAGNIFY button.

• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT
SELECT or VIDEO, or by changing the input signal.

OFF

FREEZE

Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is
displayed, and the image frozen, in the FREEZE mode.

• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the input
signal.

• Do not forget to clear frozen static images.

• Use the remote control transmitter at a distance of approximately 5m from the sensor on
the front of the projector, and within a range of 30° left-right. Strong light and obstacles will
interfere with operation of the remote control transmitter.

NOTE

Item Description

VOLUME

Volume Adjustment : Press the VOLUME / button.

MUTE (*)

Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the
MUTE mode.

AUTO

Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and
horizontal size(H.SIZE) are automatically adjusted. Use with the window at
maximum size in the application display.
Automatic Adjustment at Video Input : Press the AUTO button. A signal
type appropriate for the input signal is selected automatically. Valid only
when AUTO is set for VIDEO on the menu.

• This operation requires approximately ten seconds. It may not function correctly
with some input signals.

BLANK
ON/OFF

Set/Clear Blank Mode: Press the BLANK button. No image is displayed in
the Blank mode. The screen color is as set in BLANK on the Image menu.

MENU
ON/OFF (

*)

Menu Display Start/Stop: Press the MENU button.

• The menu display is terminated automatically after approximately ten seconds of
inactivity.

MENU
SELECT

Select Menu Type: Press the MENU SELECT button. Allows the user to
select the normal menu or the single menu. Only the selected item is
displayed on the single menu, and other items are displayed with the
and buttons as with the normal menu.

• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as "BRIGHTNESS".

• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.

Normal menu Single menu

P.IN P.
MODE

Select Mode of P.IN P. Display : Press the PinP button.

Small

→ Large → P.IN P. off (→Small)

• Valid only at RGB IN 1, RGB IN 2 or DIGITAL input.

ZOOM

Adjust Screen Size : Press the ZOOM / button.

FOCUS

Adjust Focus : Press the FOCUS / button.

ENGLISH-11

ENGLISH

ENGLISH-11

OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Items indicated by (*) may be used from the control panel.

Table 3. Basic Operation (continued)

CONTRAST

-2

BRIGHT

CONTRAST

V POSIT
H POSIT
H PHASE

H SIZE
COLOR BAL R
COLOR BAL B

ASPECT

0

-2

+1

0
0

100
100

800

SETUP INPUT OPT.IMAGE

(MENU SELECT)

ENGLISH-12ENGLISH-12

OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Setup Menu

The following adjustments and settings are possible
when SETUP is selected at the top of the menu. Part
of the Setup menu differs between RGB input and
video input. Select an item with the and
buttons, and start operation. Use the Single menu to
reduce menu size (see Table 3, MENU SELECT).

Table 4. Setup Menu

VIDEO

S-VIDEO

COMPONENT VIDEO

RGB IN 1
RGB IN 2

DIGITAL

BRIGHT

CONTRAST

V POSIT
H POSIT

H PHASE

H SIZE
COLOR BAL R
COLOR BAL B

ASPECT

0

-2

+1

0
0

100
100

800

SETUP INPUT OPT.IMAGE

BRIGHT

CONTRAST

SHARPNESS

COLOR

TINT
COLOR BAL R
COLOR BAL B

ASPECT

0
+1
+1

0

0

0

0

SETUP INPUT OPT.IMAGE

Item Description

RGB IN 1
RGB IN 2

DIGTAL

VIDEO

S-VIDEO

COMPONENT

BRIGHT

Adjustment: Dark ↔ Light

✔ ✔ ✔

CONTRAST

Adjustment: Weak ↔ Strong

✔ ✔ ✔

V POSIT

Adjustment: Down ↔ Up

✔

- -

H POSIT

Adjustment: Left ↔ Right

✔

- -

H PHASE

Adjustment: Left ↔ Right

• Adjust to eliminate flicker.

✔

- -

H SIZE

Adjustment: Small ↔ Large

• The image may not be displayed correctly if the horizontal
size is excessive. In such cases, press the RESET button,
and initialize the horizontal size.

✔

- -

SHARPNESS

Adjustment: Soft ↔ Clear

- -

✔

COLOR

Adjustment: Light ↔ Dark

- -

✔

TINT

Adjustment: Red ↔ Green

• Valid only when NTSC or NTSC 4.43 signal is received.

- -

✔

COLOR BAL R

Adjustment: Light ↔ Dark

✔ ✔ ✔

COLOR BAL B

Adjustment: Light ↔ Dark

✔ ✔ ✔

ASPECT

Select Image Aspect Ratio : 4:3[ ] ↔
16:9[ ]

Select Position of Image:

Press the button while 16:9[ ] is selected.
Center

→ Down → Up ( → Center )

✔ ✔

-

Select Image Aspect Ratio:

4:3[ ] ↔ 16:9[ ] ↔ 4:3 small[ ]

Select Position of Image :

Press the button while 16:9[ ] / 4:3 small[ ]
is selected.
Center

→ Down → Up ( → Center )

• 4:3 small may not be displayed correctly with some input
signals.

- -

✔

ENGLISH-13

ENGLISH

ENGLISH-13

OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Input Menu

The following functions are available when INPUT is selected on the
menu. Select an item with the and buttons, and start or stop
operation with the and buttons. The function indicated (**) are
effective on video input mode only, not on RGB input mode, except in
the P.IN P. window on RGB input mode.

Table 5. Input Menu

Item Description

AUTO

Automatic Adjustment at RGB Input: Select the EXECUTE with the
button.

Horizontal position (H.POSIT), vertical position (V.POSIT), clock
phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted.
Use with the window at maximum size in the application display.
Automatic Adjustment at Video Input: Select the

EXECUTE

with the
button. A signal type appropriate for the input signal is selected
automatically when

EXECUTE

is selected automatically. Valid only when

AUTO is set for VIDEO on the menu.

•

This operation requires approximately 10 seconds. It may not function correctly with

some input signals. Pressing the AUTO button in this case may correct this problem.

• This function is the same as for the AUTO function in Basic operation.

RGB

Displays RGB Input Frequency: Displays the horizontal and vertical sync
signal frequencies for RGB input.

• Valid only at RGB input.

VIDEO (**)

Select Video Signal Type: Select the signal type with the and
buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as
appropriate for the input signal. The selection of AUTO enables and
executes the function AUTO (Automatic Adjustment at Video Input), except
for the N-PAL input.

• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.

• Automatic Adjustment requires approximately ten seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may correct
this problem except for the N-PAL input.

• For the COMPONENT VIDEO input, this function is not effective and the signal type
is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the
signal of HDTV.

VIDEO NR

(**)

Set/Clear Noise Reduction Mode: Select the TURN ON / TURN OFF with
the / button. When the TURN ON is selected, the NR mode is active
and the noise on screen of the video input will be reduced.

Progressive

(**)

Select Progressive Mode: Select the mode suitable for the input signal
with the and buttons. The TV mode and the CINEMA mode convert
the interlaced video signal into the progressive signal. The CINEMA mode is
adptable 2-3 Pull-Down system to the conversion.

• Use this function to raise resolution, at the interlaced video input except HDTV
signal.

BLACK(**)

Set/Clear Black Enhancement Mode: Select the TURN ON / TURN OFF
with the / button. When the TURN ON is selected, the black
enhancement mode is active and the contrast ratio of the screen for the
video input will be raised by making black level darker.

SETUP INPUT OPT.

AUTO

RGB

VIDEO

VIDEO NR

Progressive

BLACK

IMAGE

EXECUTE
CANCEL

ENGLISH-14ENGLISH-14

OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Image Menu

The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the and buttons, and
start operation.

Table 6. Image Menu

Item Description

KEYSTONE

Keystone Adjustment:

Reduce size of bottom of image ↔ Reduce size of top of image

• When this function is activated, the image may not be displayed correctly with
some input signals.

BLANK

Select Blank Screen Color: Select color with the and buttons.

• The image is cleared when the BLANK mode is set with BLANK ON, or when there
is no signal, and the entire screen is displayed in the selected color.

MIRROR

Operation Start/Stop: Press the or button.
Select Mirror Status: Select mirror status with and buttons.

START UP

Operation Start/Stop: Press the or button.
Setup Initial Screen Display: Select TURN ON with the button.
Clear Initial Screen Display: Select TURN OFF with the button.

• Note that if TURN OFF is selected the blank screen is displayed in blue when there
is no signal.

P. IN P.

Operation Start/Stop: Press the or button.
Select Position of P. in P. Display : Press the or button.

↔↔↔(↔)

• Valid only at RGB IN 1, RGB IN 2 or DIGITAL input.

SETUP INPUT OPT.

KEYSTONE

BLANK

MIRROR

START UP

P. IN P.

IMAGE

+1

ENGLISH-15

ENGLISH

ENGLISH-15

OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Options Menu

The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the and buttons, and
start operation. The function indicated (**) are effective on video input
mode only, not on RGB input mode, except in the P.IN P. window on
RGB input mode.

Table 7. Options Menu

VOLUME

MENU COLOR

LANGUAGE

AUTO OFF

SYNC ON G

HDTV

16

SETUP INPUT OPT.IMAGE

Item Description

VOLUME

Volume Adjustment: Reduce VOLUME ↔ Increase VOLUME

MENU COLOR

Select Menu Background Color: Select with the and buttons.

LANGUAGE

Operation Start/Stop: Press the or button.
Select Menu Display Language: Select with the and buttons.

AUTO OFF

Operation Start/Stop: Press the or button.
Set AUTO OFF: Set 1~99 minutes with the and buttons. The

system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF: Select STOP (0 min.) with the button. When
STOP is selected the system does not enter the standby mode even if
no signal is received.

SYNC ON G

Operation Start/Stop: Press the or button.
SYNC ON G Valid: Select TURN ON with the button.
SYNC ON G Invalid: Select TURN OFF with the button.

• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set SYNC ON G to invalid, and reconnect the signal.

HDTV (**)

Select HDTV mode: Select the 1035i mode or 1080i mode suitable for
the input signal with the / button.

ENGLISH-16ENGLISH-16

OOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNNSSSS ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

No Signal Menu

The same adjustments and settings are available as with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.

Table 8. No Signal Menu

VOLUME

KEYSTONE

BLANK

MIRROR

START UP

MENU COLOR

LANGUAGE

AUTO OFF

SYNC ON G

16
+1

Item Description

VOLUME

Volume Adjustment: Reduce VOLUME ↔ Increase VOLUME

• When this function is used, audio input is automatically switched to video. The
audio input can be switched by moving the DISK PAD left and right during the
display of the volume adjustment bar. The volume adjustment bar is displayed by
pressing VOLUME or VOLUME button.

KEYSTONE

Keystone Adjustment: Reduce the size of bottom of image ↔
Reduce the size of top of image

BLANK

Select Blank Screen Color: Select the color with the and
buttons.

• When the blank mode is set with BLANK ON, by absence of a signal, or by
input of a non-standard signal, the image is cleared and the complete screen is
displayed in the selected color.

MIRROR

Operation Start/Stop: Press the or button.
Select Mirror Status: Select the mirror status with the and

buttons.

START UP

Operation Start/Stop: Press the or button.
Setup Initial Screen Display: Select the TURN ON with the button.
Clear Initial Screen Display: Select the TURN OFF with the button.

• Note that if TURN OFF is selected the blank screen is displayed in blue when
there is no signal.

MENU COLOR

Select Menu Background Color: Select the color with the and
buttons.

LANGUAGE

Operation Start/Stop: Press the or button.
Select Menu Display Language: Select the language with the and

buttons.

AUTO OFF

Operation start/stop: Press the or button.
Set AUTO OFF: Set 1~99 minutes with the and buttons. The

system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF: Select the STOP (0 min.) with the button. When
the STOP is selected the system does not enter the standby mode even
if no signal is received.

SYNC ON G

Operation Start/Stop: Press the or button.
SYNC ON G Valid: Select the TURN ON with the button.
SYNC ON G Invalid: Select the TURN OFF with the button.

• May not be displayed correctly with some input signals when the SYNC ON G
is valid. In such cases, remove the signal connector so that no signal is received,
set the SYNC ON G to invalid, and reconnect the signal.

ENGLISH-17

ENGLISH

ENGLISH-17

MAINTENANCE

MAINTENANCE

Lamp

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

Contact your dealer before replacing the lamp.
For the optional lamp, see the item “Option Parts” of the Table 12.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.

Lamp Life

Projector lamps have a finite life. The image will become darker, and hues will become weaker,
after a lamp has been used for a long period of time.
Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears
when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.

• The LAMP indicator is also red when the lamp unit reaches high temperature. Before

replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.

NOTE

Lamp

Front
glasss

Reflector

WARNING • For disposal of used lamp, treat
according to the instruction of community

authorities.

• Since the lamp is made of glass, do not apply shock
to it and do not scratch it.

• Also, do not use old lamp. This could also cause
explosion of the lamp.

• If it is probable that the lamp has exploded (explosive
sound is heard), disconnect the power plug from the
power outlet and ask your dealer to replace lamp. The
lamp is covered by front glass , but, in rare cases, the
reflector and the inside of the projector may be
damaged by scattered broken pieces of glass, and
broken pieces could cause injury when being handled.

• Do not use the projector with the lamp cover removed.

ENGLISH-18ENGLISH-18

MMMMAAAAIIIINNNNTTTTEEEENNNNAAAANNNNCCCCEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Replacing the Lamp

1. Switch the projector OFF, remove the power cord from the
power outlet, and wait at least 45 minutes for the unit to cool.

2. Prepare a new lamp.

3. Check that the projector has cooled sufficiently, and gently
turn it upside down.

4. Loosen the screw as shown in the diagram, and remove the
lamp cover.

5. Loosen the two screws, and gently remove the lamp while
holding the grips. Touching the inside of the lamp case may
result in uneven coloring.

6. Install the new lamp and tighten the two screws firmly. Also
steadily push the opposite side of the screwed lamp into the
unit.

7. Replace the lamp cover in position and tighten the screw
firmly.

8. Gently turn the projector right-side up.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following
operation within ten minutes of switching power ON. The power will be turned off automatically in
over 10 minutes.

1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP
xxxx hr’ message will appear on the lamp timer on the bottom of the screen.

2. Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx

→ 0 ■ CANCEL’ message will

then appear.

3. Press the and select 0, and wait until the timer display is cleared.

• Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always

when replacing the lamp. The message functions will not operate properly if the lamp timer is not
reset correctly.

NOTE

CAUTION • Ensure that screws are tightened
properly. Screws not tightened fully may result

in injury or accidents.

• Do not use the projector with the lamp cover
removed.

ENGLISH-19

ENGLISH

ENGLISH-19

MMMMAAAAIIIINNNNTTTTEEEENNNNAAAANNNNCCCCEEEE ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Air Filter Maintenance

The air filter should be cleaned as described below at intervals of approximately 100 hours.

1. Switch the projector power supply OFF, and remove the power cord from the power outlet.

2. Clean the air filter with a vacuum cleaner.

Other Maintenance

Maintenance Inside the Equipment

For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two
years. Maintaining the equipment by yourself is dangerous.

Cleaning the Lens

Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.

Cleaning the Cabinet and Remote control transmitter

Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth
dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.

CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY

INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.

• Do not use detergents or chemicals other than those noted above (e.g. benzene

or thinners).

• Do not use cleaning sprays.

• Do not rub with hard materials, or tap the equipment.

CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY

INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.

• Replace the air filter if contamination cannot be removed, or if it is damaged.

Contact your dealer in such case. For the optional air filter, see the item “Option
Parts” of the Table 12.

• Do not use the equipment with the air filter removed.

• When the air filter is clogged with dust etc. the power supply is switched OFF

automatically to prevent the temperature rising inside the projector.

ENGLISH-20ENGLISH-20

TROUBLESHOOTING

TROUBLESHOOTING

OSD Message

The messages as described below may appear on the screen at power ON. Take the appropriate
measures when such a message appears.

Table 9. OSD Messages

Message Contents

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

*1)

The message shown at left appears after the lamp has
been used for more than 1300 hours.
The lamp is approaching the end of its life.
Power is switched OFF automatically when the lamp
reaches the end of its life. Prepare a new lamp for
installation.
Always reset the lamp timer after replacing the lamp.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

THE POWER WILL TURN OFF

AFTER ** hr.

*1)

The lamp will reach the end of its life in ** hours.
Power will be switched OFF automatically in

** hours.
Replace the lamp as shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

THE POWER WILL

TURN OFF

AFTER 0 hr.

The lamp has reached the end of its life. Power will be
switched OFF in a few minutes.
Switch power OFF immediately and replace the lamp as
shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.

NO INPUT IS DETECTED

ON ***

No input signal found.
Check signal input connections and signal sources.

SYNC IS OUT OF RANGE

ON ***

The horizontal or vertical frequency of the input signal is
not within the specified range.
Check the specifications of the equipment and the signal
source.

*1) This message is cleared automatically after approximately three minutes, and appears

every time power is switched ON.

NOTE

ENGLISH-21

ENGLISH

ENGLISH-21

TTTTRRRROOOOUUUUBBBBLLLLEEEESSSSHHHHOOOOOOOOTTTTIIIINNNNGGGG ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Indicators Message

The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the
appropriate measures.

Table 10. Indicators Message

POWER

indicator

LAMP

indicator

TEMP

indicator

Contents

Lights

orange

Turns off Turns off The Standby mode has been set.

Blinks

green

Turns off Turns off Warming up. Please wait.

Lights

green

Turns off Turns off ON. Normal operation possible.

Blinks

orange

Turns off Turns off Cooling. Please wait.

Lights red

Lights

red

Turns off

Lamp is not lit.
The interior of the equipment may be too hot. Switch
power OFF, wait 20 minutes until the equipment cools,
and check whether the ventilation openings are blocked,
whether the air filter is dirty, or whether the ambient
temperature exceeds 35 °C. And switch power ON
again. Replace the lamp if the same problem occurs.

Lights red

Blinks

red

Turns off

Lamp or lamp cover is not found, or hasn’t been fitted in
correctly.
Switch power OFF, and wait for 45 minutes until the
equipment cools. Check fitting of the lamp and lamp
cover, and switch power ON again. Contact your dealer if
the same problem occurs again.

Lights red Turns off

Blinks

red

The cooling fan is not operating.
Switch power OFF, and wait for 20 minutes until the
equipment cools. Check for foreign matters in the fan,
and switch power ON again. Contact your dealer if the
same problem occurs again.

*1) When the internal temperature becomes excessive power is switched OFF

automatically for safety reasons, and the indicator is extinguished. Set the power switch to [

O

] and

wait for 20 minutes until the equipment has cooled sufficiently.

NOTE

ENGLISH-22ENGLISH-22

TTTTRRRROOOOUUUUBBBBLLLLEEEESSSSHHHHOOOOOOOOTTTTIIIINNNNGGGG ((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Symptom

Before requesting repair, check in accordance with the following chart. If the situation cannot be
corrected, then contact your dealer.

Table 11. Symptom

Symptom Possible cause Remedy Page

The power is not
turned on.

The main power switch is not
turned on.

Turn on the main power switch.

8,9

The power cord is
disconnected.

Plug the power cord into an AC
power outlet.

No video or audio.

The input is not correctly set.

Use the projector or remote control
transmitter to set.

10

No signal input. Connect correctly.

7,8

Video is present but
no audio.

The projector is not correctly
connected.

Connect correctly.

7,8

The volume is set to minimum.

Press VOLUME on the remote
control or display the menu screen
and adjust the volume.

11,15

Mute is turned on.

Press the MUTE button.

11

Audio is present but
no video.

The projector is not correctly
connected.

Connect correctly.

7,8

The brightness adjustment knob
is rotated fully clockwise.

Select BRIGHT with the MENU
button and the press the button.

12

The lens cap is still attached. Remove the lens cap.

9

Colors are pale and
color matching is
poor.

Color density and color
matching are not correctly
adjusted.

Adjust the video.

12

Images are dark.

Brightness and contrast are not
correctly adjusted.

Adjust the video.

12

The lamp is nearing the end of
its service life.

Replace with a new lamp.

17

Video is blurred.

Focus or H PHASE is out of
adjustment.

Adjust the focus or H PHASE.

9,12

ENGLISH-23

ENGLISH

ENGLISH-23

SPECIFICATIONS

SPECIFICATIONS

Table 12. Specifications

• This specifications are subject to change without notice.

NOTE

Item Specification

Product name Liquid crystal projector

Liquid
crystal
panel

Panel size 3.3 cm (1.3 type)
Drive system TFT active matrix

Pixels 786,432 pixels (1024 horizontal x 768 vertical)
Lens Zoom lens F=1.7 ~ 2.3 f=49.0 ~ 64.0 mm
Lamp 250 W UHB
Speaker 1.2 W + 1.2W (Stereo)
Power supply AC100 ~ 120V, 4.5A / AC220 ~ 240V, 2.2A
Power consumption 400W
Temperature range 0 ~ 35°C (Operating)
Size 289 (W) x 124 (H) x 350 (D) mm
Weight (mass) 6.4 kg

RGB
signal
input

RGB IN

1

Video: Analog 0.7Vp-p, 75Ω terminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack

2

DIGITAL

TMDS, DC: 150~1200 mV / AC: 1.56 Vp-p
TTL Level (Positive/Negative)

AUDIO IN

RGB1

200mVrms, 50 kΩ (max. 3.0Vp-p)
Stereo mini jack

DIGITAL
RGB2

Video
signal
input

VIDEO

1.0Vp-p, 75Ω terminator
RCA jack

S-VIDEO

Brightness signal: 1.0Vp-p, 75Ω terminator
Color signal: 0.286Vp-p (burst signal), 75Ω terminator
Mini DIN 4-pin jack

COMPONENT
VIDEO

Y 1.0 Vp-p, 75 Ω Terminator (Positive)

CB/CR 0.7 Vp-p, 75 Ω Terminator (Positive)

PB/PR 1.0 Vp-p, 75 Ω Terminator (Positive)

AUDIO

L

200mVrms, 50 kΩ (max. 3.0Vp-p)
RCA jack

R

Signal
output

RGB OUT

Video: Analog 0.7Vp-p, 75Ω output impedance (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack

AUDIO OUT

200mVrms, output impedance 1 kΩ (max. 3.0Vp-p)
Stereo mini jack

Control
functions

CONTROL D-sub 15-pin shrink plug

USB USB jack (B type)

Optional Parts

Lamp: DT00341
Air Filter: MU0832
* For others, consult your dealer.

ENGLISH-24ENGLISH-24

WARRANTY AND AFTER-SERVICE

WARRANTY AND AFTER-SERVICE

If a problem occurs with the equipment, first refer to the P.20 “TROUBLESHOOTING” section and
run through the suggested checks. If this does not resolve the problem contact your dealer or service
company. If repairs are possible, and desirable, they will be charged.

Pin No Signal Pin No Signal Pin No Signal

1 T.M.D.S. Data 2 - 11 T.M.D.S. Data 1 / 3 Shield 21 -

2 T.M.D.S. Data 2 + 12 - 22 T.M.D.S. Clock Shield

3 T.M.D.S. Data 2 / 4 Shield 13 - 23 T.M.D.S. Clock +

4 - 14 +5V Power 24 T.M.D.S. Clock -

5 - 15

Ground (+5V, Analog H/V Sync.)

6 DDC Clock 16 Hot-Plug Sense

7 DDC Data 17 T.M.D.S. Data 0 -

8 Analog V. Sync. 18 T.M.D.S. Data 0 +

9 T.M.D.S. Data 1 - 19 T.M.D.S. Data 0 / 5 Shield

10 T.M.D.S. Data 1 + 20 -

Pin No Signal Pin No Signal Pin No Signal

1 Video input Red 9 -

15

RGB IN 1: SCL(DDC)

2 Video input Green 10 Ground RGB IN 2: -

3 Video input Blue 11 - RGB OUT: -

4 -

12

RGB IN 1: SDA(DDC)

5 Ground RGB IN 2: -

6 Ground Red RGB OUT: -

7 Ground Green 13

H. sync./ Composite sync.

8 Ground Blue 14 Vertical sync

TECHNICAL - 1

TECHNICAL

TECHNICAL

TECHNICAL

Dimension Diagram

350

124

68

289

31

Unit : mm

3. Mini Din 4-pin Connector (S-VIDEO)

Pin No Signal

1

Color:0.286Vp-p (NTSC, burst signal),75Ω terminator

0.3Vp-p (PAL/SECAM, burst signal),75Ω terminator

2 Brightness:1.0Vp-p, 75Ω terminator

3 Ground

4 Ground

Signal Connector Pin Assignment

1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT)

1

23

4

5

6

7

89

10

11

1213

1415

2. Digital Receptacle Connector (DIGITAL)

123456 78
9 101112131415

17 18 19 20 21 22 23 24

16

TECHNICAL - 2

TECHNICAL

TECHNICAL

Example of computer signal

Resolution

H × V

fH (kHz) fV (Hz) Rating Signal mode

Display

mode

720 × 400

37.9 85.0 VESA TEXT Zoom in

640 × 480

31.5 59.9 VESA VGA (60Hz) Zoom in

640 × 480

35.0 66.7 Mac13"mode Zoom in

640 × 480

37.9 72.8 VESA VGA (72Hz) Zoom in

640 × 480

37.5 75.0 VESA VGA (75Hz) Zoom in

640 × 480

43.3 85.0 VESA VGA (85Hz) Zoom in

800 × 600

35.2 56.3 VESA SVGA (56Hz) Zoom in

800 × 600

37.9 60.3 VESA SVGA (60Hz) Zoom in

800 × 600

48.1 72.2 VESA SVGA (72Hz) Zoom in

800 × 600

46.9 75.0 VESA SVGA (75Hz) Zoom in

800 × 600

53.7 85.1 VESA SVGA (85Hz) Zoom in

832 × 624

49.7 74.5 Mac16"mode Zoom in

1024 × 768

48.4 60.0 VESA XGA (60Hz)

1024 × 768

56.5 70.1 VESA XGA (70Hz)

1024 × 768

60.0 75.0 VESA XGA (75Hz)

1024 × 768

68.7 85.0 VESA XGA (85Hz)

1152 × 864

67.5 75.0 VESA SXGA (75Hz) Zoom out

1280 × 960

60.0 60.0 VESA SXGA (60Hz) Zoom out

1280 × 1024

64.0 60.0 VESA SXGA (60Hz) Zoom out

1280 × 1024

80.0 75.0 VESA SXGA (75Hz) Zoom out

• Some computers may have multiple display screen modes. Use of some of these modes

will not be possible with this projector.

• Be sure to check jack type, signal level, timing and resolution before connecting this projector to a
computer.

• Depending on the input signal, full-size display may not be possible in some cases. Refer to the
number of display pixels above.

• The image might be something wrong with computer by computer on the digital RGB mode. In the
case, it is recommended to reduce the resolution and / or reflesh rate.

NOTE

TECHNICAL - 3

TECHNICAL

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Initial set signals

The following signals are used for the initial settings.
The signal timing of some computer models may be different. In such case, refer to adjust the
V.POSIT and H.POSIT of the menu.

DATA

HSYNC

DATA

VSYNC

Display interval c

Back porch b

Sync a

Front porch d

Display interval c

Back porch b

Sync a

Front porch d

Computer /

Signal

Horizontal signal timing (µs)

a b c d

TEXT 2.0 3.0 20.3 1.0

VGA (60Hz) 3.8 1.9 25.4 0.6

Mac 13"mode 2.1 3.2 21.2 2.1

VGA (72Hz) 1.3 3.8 20.3 1.0

VGA (75Hz) 2.0 3.8 20.3 0.5

VGA (85Hz) 1.6 2.2 17.8 1.6

SVGA (56Hz) 2.0 3.6 22.2 0.7

SVGA (60Hz) 3.2 2.2 20.0 1.0

SVGA (72Hz) 2.4 1.3 16.0 1.1

SVGA (75Hz) 1.6 3.2 16.2 0.3

SVGA (85Hz) 1.1 2.7 14.2 0.6

Mac 16"mode 1.1 3.9 14.5 0.6

XGA (60Hz) 2.1 2.5 15.8 0.4

XGA (70Hz) 1.8 1.9 13.7 0.3

XGA (75Hz) 1.2 2.2 13.0 0.2

XGA (85Hz) 1.0 2.2 10.8 0.5

1152×864 (75Hz)

1.2 2.4 10.7 0.6

1280×960 (60Hz)

1.0 2.9 11.9 0.9

1280×1024 (60Hz)

1.0 2.3 11.9 0.4

1280×1024 (75Hz)

1.1 1.8 9.5 0.1

Computer /

Signal

Vertical signal timimg (lines)

a b c d

TEXT 3 42 400 1

VGA (60Hz) 2 33 480 10

Mac 13"mode 3 39 480 3

VGA (72Hz) 3 28 480 9

VGA (75Hz) 3 16 480 1

VGA (85Hz) 3 25 480 1

SVGA (56Hz) 2 22 600 1

SVGA (60Hz) 4 23 600 1

SVGA (72Hz) 6 23 600 37

SVGA (75Hz) 3 21 600 1

SVGA (85Hz) 3 27 600 1

Mac 16"mode 3 39 624 1

XGA (60Hz) 6 29 768 3

XGA (70Hz) 6 29 768 3

XGA (75Hz) 3 28 768 1

XGA (85Hz) 3 36 768 1

1152×864 (75Hz)

3 32 864 1

1280×960 (60Hz)

3 36 960 1

1280×1024 (60Hz)

3 38 1024 1

1280×1024 (75Hz)

3 38 1024 1

TECHNICAL - 4

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Connection to the Mouse Control

1. PS/2, ADB or Serial Mouse

(1) Turn off the projector and computer, and connect the two units with the appropriate cable. For

PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult

your dealer.
(2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector.
(3) Turn on the computer.
(4)

Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or

reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4.

2. USB Mouse

(1) Connect the projector and computer with a suitable commercially available USB cable. Consult

your dealer to get the cable, if you need.
(2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT

button” of page 4.

• Before connecting, read the instruction manuals of the devices to be connected.

• In the case of notebook type computers with an internal pointing device, the mouse control

function will not work unless the internal pointing device is disabled. In such case, disable the
internal pointing device and change the BIOS setting to select an external mouse before the
operations described in (1) to (5) above.
Also, some computers may not have a utility program to operate a mouse.
Refer to the computer hardware manual for detail.

NOTE

PS/2 Mouse

2

1

4

3

6

5

2

1

4

3

6

5

8

7

10

9

12

11

14

13

15

CLK

DATA

SEL0

RTS

GND

+5V

DATA

GND

+5V

CLK

2

1

4

3

6

5

Mouse jack

Mini DIN 6-pin

Projector

Computer

1

2

3

4

5

678

9

10

11 12

13

14

15

CONTROL Terminal

D-sub 15-pin shrink jack

TECHNICAL - 5

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

TECHNICAL

1

2

3

4

1

2

3

4

+

5V

—

DATA

+

DATA

GND

+

5V

—

DATA

+

DATA

GND

1

234

2

1

3

4

USB jack

(B type)

USB jack

(A type)

Projector

USB cable

Computer

ADB Mouse

2

1

4

3

6

5

2

1

4

3

8

7

10

9

12

11

14

13

15

RTS

GND

+5V

ADB

GND

+5V

(

POWER ON

)

DATA

2

1

4

3

Mouse jack

Mini DIN 4-pin

Projector

Computer

1

2

3

4

5

678

9

10

11 12 13

14

15

CONTROL Terminal

D-sub 15-pin shrink jack

Serial Mouse

2

1

4

3

6

5

2

1

4

3

6

5

8

7

10

9

8

7

9

12

11

14

13

15

RI

CD

RD

TD
DTR
GND
DSR

CTS

RTS

RTS

GND

SEL0

TD

21

4

3

6

5

8

9

7

Mouse jack
D-sub 9-pin

Projector

Computer

1

2

3

4

5

678

9

10

11 12 13

14

15

CONTROL Terminal

D-sub 15-pin shrink jack

USB Mouse

TECHNICAL - 6

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

RS-232C communication

(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.
(2) Turn on the computer power supply and, after the computer has started up, turn on the projector

power supply.

1

23

4

5

6

7

89

10

11

1213

1415

Control jack

D-sub 15-pin shrink jack

1
2
3
4
5
6
7
8
9

10

11

12

13
14

15

RD
TD

GND

SELO

RTS

1
2
3
4
5
6
7
8
9

CD
RD
TD
DTR
GND
DSR
RTS
DTS
RI

1

2345

67

8

9

RS-232C jack

D-sub 9-pin

Projector Computer

Communications setting

19200bps, 8N1

1 Protocol

Consist of header (7 bytes) + command data (6 bytes).

2 Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data.
CRC_high : Upper byte of CRC flag for command data.

3 Command data

byte_0 byte_1 byte_2 byte_3 byte_4 byte_5

Action Type Setting code

low high low high low high

Command data chart

Action (byte_0 - 1)

Action Classification Content

1 SET Change setting to desired value.

2 GET Read projector internal setup value.

4 INCREMENT Increment setup value by 1.

5 DECREMENT Decrement setup value by 1.

6 EXECUTE Run a command.

TECHNICAL - 7

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

TECHNICAL

Requesting projector status (Get command)

(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’)

from the computer to the projector.

(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.

Changing the projector settings (Set command)

(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2

bytes)) from the computer to the projector.

(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.

Using the projector default settings (Reset Command)

(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+ type (2

bytes) +‘00H’+‘00H’) to the projector.

(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.

Increasing the projector setting value (Increment command)

(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+ type (2 bytes)

+‘00H’+‘00H’) to the projector.

(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.

Decreasing the projector setting value (Decrement command)

(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+ type (2 bytes)

+‘00H’ + ‘00H’) to the projector.

(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.

When a command sent by the projector cannot be understood by the computer

When the command sent by the projector cannot be understood, the error command ‘15H’ is
returned by the computer. Some times, the projector ignores RS-232C commands during other
works. If the error command ‘15H’ is returned, please send the same command again.

When data sent by the projector cannot be practice

When the command sent by the projector cannot be practiced, the the error code ‘1cH’ +‘xxxxH’ is
returned.
When the data length is greater than indicated by the data length code, the projector will ignore the
excess data code.
Conversely, when the data length is shorter than indicated by the data length code, an error code
will be returned to the projector.

• Operation cannot be guaranteed when the projector receives an undefined command or

data.

•

Provide an interval of at least 40ms between the response code and any other code.

• The projector outputs test data when the power supply is switched ON, and when the lamp is lit.
Ignore this data.

• Commands are not accepted during warm-up.

NOTE

TECHNICAL - 8

Names Operation type Header

Command data

CRC Action Type Setting code

Blank Color

Set

Red BE EF 03 06 00 3B D3 01 00 00 30 00 00

Orange BE EF 03 06 00 AB D2 01 00 00 30 01 00

Green BE EF 03 06 00 5B D2 01 00 00 30 02 00

Blue BE EF 03 06 00 CB D3 01 00 00 30 03 00

Purple BE EF 03 06 00 FB D1 01 00 00 30 04 00

White BE EF 03 06 00 6B D0 01 00 00 30 05 00

Black BE EF 03 06 00 9B D0 01 00 00 30 06 00

Get BE EF 03 06 00 08 D3 02 00 00 30 00 00

Mirror

Set

Normal BE EF 03 06 00 C7 D2 01 00 01 30 00 00

H Inverse BE EF 03 06 00 57 D3 01 00 01 30 01 00

V lnverse BE EF 03 06 00 A7 D3 01 00 01 30 02 00

H&V Inverse BE EF 03 06 00 37 D2 01 00 01 30 03 00

Get BE EF 03 06 00 F4 D2 02 00 01 30 00 00

Freeze

Set

Normal BE EF 03 06 00 83 D2 01 00 02 30 00 00

Freeze BE EF 03 06 00 13 D3 01 00 02 30 01 00

Get BE EF 03 06 00 B0 D2 02 00 02 30 00 00

Menu Color

Set

Red BE EF 03 06 00 7F D3 01 00 03 30 00 00

Orange BE EF 03 06 00 EF D2 01 00 03 30 01 00

Green BE EF 03 06 00 1F D2 01 00 03 30 02 00

Blub BE EF 03 06 00 8F D3 01 00 03 30 03 00

Purple BE EF 03 06 00 BF D1 01 00 03 30 04 00

Transparent BE EF 03 06 00 2F D0 01 00 03 30 05 00

Gray BE EF 03 06 00 DF D0 01 00 03 30 06 00

Get BE EF 03 06 00 4C D3 02 00 03 30 00 00

Startup

Set

Turn ON BE EF 03 06 00 0B D2 01 00 04 30 00 00

Turn OFF BE EF 03 06 00 9B D3 01 00 04 30 01 00

Get BE EF 03 06 00 38 D2 02 00 04 30 00 00

Language

Set

English BE EF 03 06 00 F7 D3 01 00 05 30 00 00

Français BE EF 03 06 00 67 D2 01 00 05 30 01 00

Deutsch BE EF 03 06 00 97 D2 01 00 05 30 02 00

Español BE EF 03 06 00 07 D3 01 00 05 30 03 00

Italiano BE EF 03 06 00 37 D1 01 00 05 30 04 00

Norsk BE EF 03 06 00 A7 D0 01 00 05 30 05 00

Nederlands BE EF 03 06 00 57 D0 01 00 05 30 06 00

Português BE EF 03 06 00 C7 D1 01 00 05 30 07 00

Japanese BE EF 03 06 00 37 D4 01 00 05 30 08 00

Get BE EF 03 06 00 C4 D3 02 00 05 30 00 00

Command data chart

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

TECHNICAL - 9

TECHNICAL

Names Operation type Header

Command data

CRC Action Type Setting code

Magnify

Get BE EF 03 06 00 7C D2 02 00 07 30 00 00

Increment BE EF 03 06 00 1A D2 04 00 07 30 00 00

Decrement BE EF 03 06 00 CB D3 05 00 07 30 00 00

Auto off

Get BE EF 03 06 00 08 86 02 00 10 31 00 00

Increment BE EF 03 06 00 6E 86 04 00 10 31 00 00

Decrement BE EF 03 06 00 BF 87 05 00 10 31 00 00

Brightness Reset Execute BE EF 03 06 00 58 D3 06 00 00 70 00 00

Contrast Reset Execute BE EF 03 06 00 A4 D2 06 00 01 70 00 00

V.Position Reset Execute BE EF 03 06 00 E0 D2 06 00 02 70 00 00

H.Position Reset Execute BE EF 03 06 00 IC D3 06 00 03 70 00 00

H.Size Reset Execute BE EF 03 06 00 68 D2 06 00 04 70 00 00

Color Balance R Reset Execute BE EF 03 06 00 94 D3 06 00 05 70 00 00

Color Balance B Reset Execute BE EF 03 06 00 D0 D3 06 00 06 70 00 00

Sharpness Reset Execute BE EF 03 06 00 C4 D0 06 00 09 70 00 00

Color Reset Execute BE EF 03 06 00 80 D0 06 00 0A 70 00 00

Tint Reset Execute BE EF 03 06 00 7C D1 06 00 0B 70 00 00

Keystone Reset Execute BE EF 03 06 00 08 D0 06 00 0C 70 00 00

Auto Execute BE EF 03 06 00 91 D0 06 00 0A 20 00 00

Blank on/off

Set

off BE EF 03 06 00 FB D8 01 00 20 30 00 00

on BE EF 03 06 00 6B D9 01 00 20 30 01 00

Get BE EF 03 06 00 C8 D8 02 00 20 30 00 00

Error Status Get

BE EF 03 06 00 D9 D8 02 00 20 60 00 00

(Example of Return)
00 00 01 00 02 00 03 00
(Normal) (Cover-error) (Fan-error) (Lamp-error)

04 00 05 00 06 00
(reserved) (reserved) (Lamp-Time-over)

Power

Set

OFF

BE EF 03 06 00 2A D3 01 00 00 60 00 00

ON

BE EF 03 06 00 BA D2 01 00 00 60 01 00

Get

BE EF 03 06 00 19 D3 02 00 00 60 00 00

Input Source

Set

RGB1 BE EF 03 06 00 FE D2 01 00 00 20 00 00

RGB2 BE EF 03 06 00 3E D0 01 00 00 20 04 00

Digital BE EF 03 06 00 0E D2 01 00 00 20 03 00

Video BE EF 03 06 00 6E D3 01 00 00 20 01 00

SVideo BE EF 03 06 00 9E D3 01 00 00 20 02 00

Component

BE EF 03 06 00 AE D1 01 00 00 20 05 00

Get BE EF 03 06 00 CD D2 02 00 00 20 02 00

Volume

Get BE EF 03 06 00 31 D3 02 00 01 20 00 00

Increment BE EF 03 06 00 57 D3 04 00 01 20 00 00

Decrement BE EF 03 06 00 86 D2 05 00 01 20 00 00

Command data chart

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

TECHNICAL - 10

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Names Operation type Header

Command data

CRC Action Type Setting code

Mute

Set

Normal BE EF 03 06 00 46 D3 01 00 02 20 00 00

Mute BE EF 03 06 00 D6 D2 01 00 02 20 01 00

Get BE EF 03 06 00 75 D3 02 00 02 20 00 00

Brightness

Get BE EF 03 06 00 89 D2 02 00 03 20 00 00

Increment BE EF 03 06 00 EF D2 04 00 03 20 00 00

Decrement BE EF 03 06 00 3E D3 05 00 03 20 00 00

Contrast

Get BE EF 03 06 00 FD D3 02 00 04 20 00 00

Increment BE EF 03 06 00 9B D3 04 00 04 20 00 00

Decrement BE EF 03 06 00 4A D2 05 00 04 20 00 00

Color

Balance R

Get BE EF 03 06 00 01 D2 02 00 05 20 00 00

Increment BE EF 03 06 00 67 D2 04 00 05 20 00 00

Decrement BE EF 03 06 00 B6 D3 05 00 05 20 00 00

Color

Balance B

Get BE EF 03 06 00 45 D2 02 00 06 20 00 00

Increment BE EF 03 06 00 23 D2 04 00 06 20 00 00

Decrement BE EF 03 06 00 F2 D3 05 00 06 20 00 00

Keystone

Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00

Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00

Decrement BE EF 03 06 00 0E D2 05 00 07 20 00 00

Aspect

Set

4:3 BE EF 03 06 00 9E D0 01 00 08 20 00 00

16:9 BE EF 03 06 00 0E D1 01 00 08 20 01 00

Small BE EF 03 06 00 FE D1 01 00 08 20 02 00

Get BE EF 03 06 00 AD D0 02 00 08 20 00 00

Display

Position at

16 : 9 or Small

Set

Default BE EF 03 06 00 62 D1 01 00 09 20 00 00

Bottom BE EF 03 06 00 F2 D0 01 00 09 20 01 00

Top BE EF 03 06 00 02 D0 01 00 09 20 02 00

Get BE EF 03 06 00 51 D1 02 00 09 20 00 00

V.Position

Get BE EF 03 06 00 0D 83 02 00 00 21 00 00

Increment BE EF 03 06 00 6B 83 04 00 00 21 00 00

Decrement BE EF 03 06 00 BA 82 05 00 00 21 00 00

H.Position

Get BE EF 03 06 00 F1 82 02 00 01 21 00 00

Increment BE EF 03 06 00 97 82 04 00 01 21 00 00

Decrement BE EF 03 06 00 46 83 05 00 01 21 00 00

H.Size

Get BE EF 03 06 00 B5 82 02 00 02 21 00 00

Increment BE EF 03 06 00 D3 82 04 00 02 21 00 00

Decrement BE EF 03 06 00 02 83 05 00 02 21 00 00

H.Phase

Get BE EF 03 06 00 49 83 02 00 03 21 00 00

Increment BE EF 03 06 00 2F 83 04 00 03 21 00 00

Decrement BE EF 03 06 00 FE 82 05 00 03 21 00 00

Command data chart

TECHNICAL - 11

TECHNICAL

Names Operation type Header

Command data

CRC Action Type Setting code

Sharpness

Get BE EF 03 06 00 F1 72 02 00 01 22 00 00

Increment BE EF 03 06 00 97 72 04 00 01 22 00 00

Decrement BE EF 03 06 00 46 73 05 00 01 22 00 00

Color

Get BE EF 03 06 00 B5 72 02 00 02 22 00 00

Increment BE EF 03 06 00 D3 72 04 00 02 22 00 00

Decrement BE EF 03 06 00 02 73 05 00 02 22 00 00

Tint

Get BE EF 03 06 00 49 73 02 00 03 22 00 00

Increment BE EF 03 06 00 2F 73 04 00 03 22 00 00

Decrement BE EF 03 06 00 FE 72 05 00 03 22 00 00

Video Format

Set

Auto BE EF 03 06 00 9E 75 01 00 00 22 0A 00

NTSC BE EF 03 06 00 FE 71 01 00 00 22 04 00

PAL BE EF 03 06 00 6E 70 01 00 00 22 05 00

SECAM BE EF 03 06 00 6E 75 01 00 00 22 09 00

NTSC 4.43 BE EF 03 06 00 5E 72 01 00 00 22 02 00

M-PAL BE EF 03 06 00 FE 74 01 00 00 22 08 00

N-PAL BE EF 03 06 00 0E 71 01 00 00 22 07 00

Get BE EF 03 06 00 0D 73 02 00 00 22 00 00

Video NR

Set

off BE EF 03 06 00 B6 73 01 00 06 22 00 00

on BE EF 03 06 00 26 72 01 00 06 22 01 00

Get BE EF 03 06 00 85 73 02 00 06 22 00 00

Progressive

Set

off BE EF 03 06 00 4A 72 01 00 07 22 00 00

TV BE EF 03 06 00 DA 73 01 00 07 22 01 00

CINEMA BE EF 03 06 00 2A 73 01 00 07 22 02 00

Get BE EF 03 06 00 79 72 02 00 07 22 00 00

Black

Set

off BE EF 03 06 00 5E 71 01 00 08 22 00 00

on BE EF 03 06 00 CE 70 01 00 08 22 01 00

Get BE EF 03 06 00 6D 71 02 00 08 22 00 00

HDTV

Set

1080i BE EF 03 06 00 F2 73 01 00 05 22 00 00

1035i BE EF 03 06 00 62 72 01 00 05 22 01 00

Get BE EF 03 06 00 C1 73 02 00 05 22 00 00

PinP Size

Set

off BE EF 03 06 00 FE 22 01 00 00 23 00 00

Large BE EF 03 06 00 6E 23 01 00 00 23 01 00

Small BE EF 03 06 00 9E 23 01 00 00 23 02 00

Get BE EF 03 06 00 Cd 22 02 00 00 23 00 00

Command data chart

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Names Operation type Header

Command data

CRC Action Type Setting code

PinP Position

Set

Upper left BE EF 03 06 00 02 23 01 00 01 23 00 00

Upper right BE EF 03 06 00 92 22 01 00 01 23 01 00

bottom left BE EF 03 06 00 62 22 01 00 01 23 03 00

bottom right BE EF 03 06 00 F2 23 01 00 01 23 02 00

Get BE EF 03 06 00 31 23 02 00 01 23 00 00

PinP Audio ch

Set

RGB BE EF 03 06 00 BA 22 01 00 03 23 00 00

Video BE EF 03 06 00 2A 23 01 00 03 23 01 00

Get BE EF 03 06 00 89 22 02 00 03 23 00 00

FOCUS

Increment BE EF 03 06 00 6A 93 04 00 00 24 00 00

Decrement BE EF 03 06 00 BB 92 05 00 00 24 00 00

Zoom

Increment BE EF 03 06 00 96 92 04 00 01 24 00 00

Decrement BE EF 03 06 00 47 93 05 00 01 24 00 00

Sync on G

Set

off BE EF 03 06 00 CB D0 01 00 08 30 01 00

on BE EF 03 06 00 5B D1 01 00 08 30 00 00

Get BE EF 03 06 00 68 D1 02 00 08 30 00 00

TECHNICAL - 12

TTTTEEEECCCCHHHHNNNNIIIICCCCAAAALLLL((((ccccoooonnnnttttiiiinnnnuuuueeeedddd))

))

Command data chart

REGULATORY NOTICES - 1

REGULATORY NOTICES - 1

REGULATORY NOTICES

REGULATORY NOTICES

WARNING: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements
of FCC (Federal Communication Commission) equipment provided that the
following conditions are met.
The cables may have to be used with the core set to the projector side. Use
the cables which are included with the projector or specified.

CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.

FCC Statement Warning

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Pour les utilisateurs au Canada

AVIS: Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du
Canada.

Core

LEGAL INFORMATION

FIVE-YEAR LIMITED WARRANTY

This Dukane LCD projector is warranted to the original purchaser for a period of
five (5) years from the original purchase date - in normal use and service ­against defects in material and workmanship. DUKANE CORPORATION
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.

During the warranty period, Dukane Corporation will repair or replace (at the
manufacturer's option) any such defective parts (except for the lamp, which is
subject to whatever warranties the manufacturer may provide) without charge to
the purchaser for parts or labor when the product is returned, prepaid and insured,
with proof-of-purchase date. This remedy is void if the product has been
damaged by accident, unreasonable use, neglect, improper service or other
causes not arising out of defects in material or workmanship.

Dukane Corporation disclaims all liability for incidental or consequential damage
of any kind, including all damages arising out of any interruptions in operation of
the product and all damages to software.

No person, firm, or representative is authorized to assume any obligation or to
make any warranty on behalf of the Dukane Corporation other than as stated
above.

THIS LIMITED WARRANTY IS VALID FOR U.S.A AND CANADA.
FOR OTHER LOCATIONS, LOCAL WARRANTIES APPLY.

LAMP REPLACEMENT SERVICE & REPAIR POLICY & PROCEDURE

For service and parts, contact the Dukane AV Service Department
at 1 [phone] within the USA or 1 [phone] worldwide.
If you would like to send a facsimile (FAX), dial 1 [phone] worldwide.

When requesting warranty service, please have the sales receipt available along
with the model name and serial number.

If it becomes necessary to return the projector, use the original packing material
and box (if retained) or pack securely. Dukane Corporation will not be liable for
any pick-up or delivery charges or any expenses incurred for service calls or
service supplied by anyone other than the Dukane AV Service Department.

Dukane Corporation
Audio Visual Products Division
2900 Dukane Drive
St. Charles, IL 60174-3395
E-mail: [e-mail]

Audio Visual Products

Phone: [phone]

Orders: [phone]

Information: [phone]

Fax: [phone]

Parts & Service: [phone]

Fax: [phone]

Part # 401-571-00