Duevi EzyDriveCAM Hardware Installation Manual
This device meets the R&TTE requirements (European Union)
EzyDrive
EzyDriveEzyDrive
EzyDriveCAM
D I G I T A L V I D E O R E C O R D E R
HARDWARE INSTALLATION MANUAL
(VERSION 3.0)
Software manual only on CD
This manual may be subject to change without notice
2
Thank you for choosing our product.
We invite you to read carefully these directions before installing and using this device in order to fully make
the most of all its capacities.
1. INTRODUCTION
THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY IMPROPER USE OF THE PRODUCT,
INCORRECT INSTALLATION OR FAILURE TO COMPLY WITH INSTRUCTIONS OF THIS MANUAL
AND THE LAW REGARDING ELECTRICAL SYSTEMS.
DO NOT CLEAN THE CASE WITH ALCOHOL OR OTHER LIQUID CLEANER BUT ONLY WITH A
CLOTH BARELY DAMPENED WITH WATER.
IN CASE OF FAILURE OF THE DEVICE DO NOT TRY TO REPAIR IT YOURSELF BUT BRING TO THE
NEAREST AUTHORIZED SERVICE CENTER.
EEEEzyMegaCAM
zyMegaCAMzyMegaCAM
zyMegaCAM is a megapixel camera with recording storage on board that can be questioned by a vision
and programming software (EzyViewCAM) through locale network, power line (HomePlug® system) or
remote connection (WEB).
It can be visualized and programmed by EzyTV also, for management without PC.
The non-volatile memory inserted in the device (up to two SD card) make possible to store the video
directly in MPG4 format, therefore it is not needed any server or additional video recorder.
The rechargeable backup battery allows to record even in case of power supply 12 V lack.
The EzyMegaCAM are equipped of:
• alarm input: NC at +12 V
• open-collector output useful for command a device from remote
• onboard IR detector, for detect the presence of strangers and activate the video recording
• light sensor: EzyCAM defines day and night, adapting the C-MOS sensor parameters for having
always the best image quality during day and night.
3
2. DEVICECONNECTION
Figure 1 – Electronic board of EzyMegaCAM
LAN
(connector side)
POWER SUPPLY
Can be in two different types. When using PoE, do NOT connect 12 V power supply!
12 V POWER SUPPLY
PoE
Power is supplied by LAN (if present a Power
over Ethernet system)
+12V
GND
BAT
Backup battery
connector
LAN
LAN connector RJ45
type
Power supply 12 V
Power 12 V
Not necessary if using the PoE (LAN)
system
MASTER slot
Lower slot
Use ONLY this one
in case of single SD
card
SLAVE slot
Upper slot
DO NOT use in case
of single SD card
Double SD slot
To install up to
two SD cards
(must be
identical).
Insert/remove
only with device
completely
unpowered
Input/Output
Use provided cable
4
Figure 2 – Electronic board of EzyMegaCAM
POF
(connector side)
POWER SUPPLY
The camera can be powered:
power supply 12 ÷ 30 V or power supply 24 V
The POWER connector does not have preferential polarity (even in case of CC)
POWER
BAT
Backup battery
connector
POF1 LED
Network activity
MASTER slot
Lower slot
Use ONLY this one
in case of single SD
card
SLAVE slot
Upper slot
DO NOT use in case
of single SD card
Double SD slot
To install up to
two SD cards
(must be
identical).
Insert/remove
only with device
completely
unpowered
Input/Output
Use provided cable
POF1
Plastic optic fiber
connector (LAN)
POF2
Plastic optic fiber
connector (LAN)
POF2 LED
Network activity
5
Figura 3 – Electronic board of EzyMegaCAMPL (connector side)
TO PREVENT
TO PREVENT TO PREVENT
TO PREVENT THE RISK OF ELECTRIC SHOCK, OPEN THE DEVICE COVER ONLY
THE RISK OF ELECTRIC SHOCK, OPEN THE DEVICE COVER ONLY THE RISK OF ELECTRIC SHOCK, OPEN THE DEVICE COVER ONLY
THE RISK OF ELECTRIC SHOCK, OPEN THE DEVICE COVER ONLY
WHEN THE 110
WHEN THE 110WHEN THE 110
WHEN THE 110 VVVV / 230
/ 230/ 230
/ 230 VVVV POWER SUPPLY IS SWITCHED OFF
POWER SUPPLY IS SWITCHED OFFPOWER SUPPLY IS SWITCHED OFF
POWER SUPPLY IS SWITCHED OFF....
POWER
and DATA
The camera is powered directly by 230 V power line
Data communication from/to the camera is made through power line by HomePlug® 1.0 system
GND
230 V
BAT
Backup battery
connector
Activity LED
Data transfer
MASTER slot
Lower slot
Use ONLY this one
in case of single SD
card
SLAVE slot
Upper slot
DO NOT use in case
of single SD card
Double SD slot
To install up to
two SD cards
(must be
identical).
Insert/remove
only with device
completely
unpowered
Input/Output
Use provided cable
Link LED
Connection to
HomPlug system
230 V
AC
N = Neutral (blue)
F = Phase (brown)
Loading...