SAFETY INFORMATION
THE SANDWICH TOASTER
2 3
1. Sandwich cages.
2. 28mm wide slots - Fit sandwiches or large buns in
these super wide slots.
3. Adjustable foot - can be rasied or lowered to
compensate for uneven surfaces.
4. Crumb tray - Removable easy clean tray catches
drips of crumbs.
5. Ejector knob - Manualy eject buns from the slots.
6. Mechanical timer - on/off control with countdown
timer.
7. Slot selector switch - select which slots will heat up.
8. Stainless steel cover - easy clean durable cover.
• The sandwich toasters are supplied with Sandwich cages.
Additional cages can be purchased as an accessory.
• Using medium sliced bread, lightly butter one side of each
slice and place lling between un-buttered sides. Use the
sandwich cage recipe book for various ideas. Pre-sliced or grated
cheeses work best.
• Place sandwich into a cage and insert into one of the slots.
• The two slot sandwich toaster uses two timer dials. (The top one
switches on the left hand slot and the bottom one switch the right
hand slot).
• The four slot has a 3 position rotary switch to select 1,2 or 4
slots and a single timer.
• Set timer dial for each loaded slot to between no. 2.5 and no. 3.5
according to the darkness required. After the toaster has
warmed up, reduce time by half a number (Usually after 2 or 3
cycles).
• The timer dial turns off automatically after the selected
time cycle has nished or can be reset manually by turning the
timer knob back to the off position.
• The sandwiches will keep warm inside the toaster until removed
for serving.
USING A SANDWICH TOASTER
CLEANING REPLACING ELEMENTS
• See the included recipe booklet for lots of inspirational ideas.
• Always lightly butter the OUTER sides of the sandwich as this will
make the lling hotter.
• We recommend the use of 1 or 2 day old bread. Slices should
be cleanly cut & not ragged edged.
• Very thinly sliced bread may produce uneven toasting.
• Do not force in thick slices of bread as you may experience
difculty in ejecting them. Never insert broken pieces of bread.
• If heated slots are left empty the adjacent slots will toast
unevenly.
CAUTION: Heating up slots that have not been loaded with bread
may damage the elements and will cause uneven toasting. Do not
use the toaster if the crumb tray or base plate are missing or are
incorrectly tted and never cover the top of the toaster or use as a
hot plate. Always unplug the toaster when not in use.
READ ALL INSTRUCTIONS
Before using the toaster .Keep these instructions for future
reference.
• WARNING: This appliance must be earthed.
• We recommend that the toaster is plugged into a socket that
has no other appliance connected to it.
Failure to do this may cause an overload, trip a circuit breaker or
blow a fuse. Preferably the socket outlet should be protected by
a Residual Current device (RCD).
• Before plugging in, check that the voltage on the rating label is
the same as the mains supply.
• To protect against electric shock, do not immerse any part of
this product in water or other liquid.
• Unplug from outlet when not in use and before cleaning. Allow
to cool before putting on or taking off parts.
• Do not operate the appliance with a damaged cord or plug.
• Do not allow cable to touch hot surfaces, or to hang over edge
of a table or counter top.
• When in use a re may occur if the toaster is covered or
touching ammable material.
• Do not attempt to dislodge bread when the toaster is plugged
in.
• Bread may burn. Therefore toasters must not be used near or
below curtains and other combustible materials.
• When toasting do not leave appliance unattended.
THIS IS AN ATTENDED APPLIANCE
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with this appliance.
• Do not store toaster in an appliance garage or under
cupboards.
• Do not use outdoors.
• The toaster is not intended to be operated by means of an
external timer or separate remote-control system.
• Accessible surfaces of the toaster may get hot during use.
• NOTE: Any plug cut from power supply cord should be
disposed of immediately. Inserting any cut off plug into a 13A
socket-outlet is hazardous.
• Never use the plug without the fuse cover tted. Ensure
replacement fuse is the same current value as original.
• Replacement fuses should be ASTA approved to BS 1362.
• Do not operate any appliance with a damaged lead or plug, or
after the appliance malfunctions, or has been damaged in any
manner.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
SAVE THESE INSTRUCTIONS
Accessible surfaces of the toaster
may get hot during use.
Cleaning and maintaining your toaster on a regular basis will
keep it shining and prolong the life of your machine.
• IMPORTANT: Always unplug the toaster and allow to cool
down before performing any cleaning.
• Remove crumb tray & clean daily.
• Crumbs should be carefully brushed off the elements (using
only a soft brush), the toaster turned upside down and shaken
out.
• Never insert a fork or other sharp instrument to remove torn
pieces of bread as the heating elements may be damaged.
• Use a microber or damp cloth to wipe off the outside surfaces
of the toaster. Do not use any cleaner on the end castings, wipe
and dry.
• A stainless steel polish can be used to restore shine but this
must not be an aggressive cleaner or contain ammonia and
should only be used on the stainless steel cover.
• This appliance must not be immersed in water or cleaned
with a water jet.
• Sandwich cages are dishwasher safe or can be washed in
warm soapy water. Do not use abrasive cleaners.
• Empty the crumb tray on a daily basis, do not allow crumbs to
build up.
Spares for your Dualit toasters are available by mail order, call us
on 01293 652 500 for more details.
• Servicing must only be carried out by Dualit authorised service
agent or a competent electrician.
• For your own protection only use original Dualit spares.
• When replacing ProHeat elements, only use genuine Dualit
elements (stamped "DUALIT") the safety and the performance of
the toaster cannot be guaranteed if inferior elements are used.
Fitting of non Dualit parts will also invalidate the guarantee.
• A. Disconnect toaster from mains.
• B. Remove the crumb tray.
• C. Unscrew feet and remove base
• D. Loosen the two nuts and slide back element retaining strip.
• E. Note the position of the connecting links and wires, then
unscrew nuts which secure them to the broken element, bend back
the connecting links, pull out the old element and slide in the new
element. Fasten connecting links back to their original position by
tightening the nuts.
• F. Slide back element retaining strip and tighten nuts.
• G. Make sure that you have the high wattage elements marked
'CENTRE" or low wattage elements marked "END". Different
toasters have different element congurations, if you are unsure
please call the dualit helpline on 01263 652 500.
• H. Ret base plate, feet and crumb tray.
8
1
3
2
7
6
4 5