DTS SCENA LED 80 PC FC, SCENA LED 80 FR FC User Manual

Page 1
SCENA LED 80 FC
Made in Italy
SCENA LED 80 FR FC
SCENA LED 80 PC FC
User’s Manual rel. 1.0 GB
D.T.S. Illuminazione s.r.l. – ITALY http://www.dts-lighting.it/
Page 2
2
Le informazioni contenute in questo documento sono state attentamente redatte e
controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.
Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,
riprodotto per intero o in parte senza previo consenso scritto della D.T.S .
D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche
estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna
responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are
reserved and this document cannot be copied, photocopied or reproduced, in part or
completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to
any of its products without prior notice. D.T.S. assumes no responsibility for the use or
application of the products or circuits described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées
avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas
d'éventuelles inexactitudes. Tous droits réservés. Ce document ne peut être copié,
photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement
préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,
fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline
toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits
décrits.
Las informaciones contenidas en este documento han sido cuidadosamente
redactadas y controladas. Con todo, no se asume ninguna responsabilidad por
eventuales inexactitudes. Todos los derechos han sido reservados y este documento
no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa
autorización escrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de
carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume
responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los
productos o de los circuitos descritos.
Page 3
3
INDEX:
1- SYMBOLS ................................................................................................................. 4
2- GENERAL WARNING .............................................................................................. 4
3- GENERAL WARRANTY CONDITIONS .................................................................... 4
4- TECHNICAL FEATURES ......................................................................................... 5
5- ACCESSORIES ........................................................................................................ 6
6- IMPORTANT SAFETY INFORMATION .................................................................... 7
6.1 Fire prevention...................................................................................................... 7
6.2 Prevention of electric shock .................................................................................. 7
6.3 Safety ................................................................................................................... 7
6.4 Waste Electrical and Electronic Equipment directive ............................................ 7
7- INPUT / OUTPUT CONNECTIONS ........................................................................... 8
8- DMX SIGNAL CONNECTION ................................................................................... 9
8.1 DMX Addresses .................................................................................................. 10
8.2 Selecting the DMX address ................................................................................ 10
9- FIRMWARE UPDATING ......................................................................................... 10
10- DISPLAY FUNCTIONS ......................................................................................... 11
11- DMX PROTOCOL ................................................................................................. 17
Page 4
4
!
1- SYMBOLS Graphic symbols used on this manual:
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC SHOCK
RISK
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS YOU CAN PLACE THE
UNIT ON NORMALLY FLAMMABLE SURFACES
THIS SYMBOL INDICATES THE MINIMUM
DISTANCE TO BE KEPT BETWEEN THE UNIT
AND THE ILLUMINATED OBJECTS
THIS SYMBOL INDICATES THE EUROPEAN
COMMUNITY DIRECTIVE 2002/96/EC ON WASTE
ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important information regarding safety during installation , use and maintenance. The device is not for domestic use and must be installed by a qualified electrician or experienced person. Always disconnect the device from the mains before maintenance. The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 36 months from the date of purchase against manufacturing material defects.
LED 30 cm
Page 5
5
4- TECHNICAL FEATURES
OVERVIEW
SCENA LED 80 FC is a compact, lightweight, DMX-controlled LED projector equipped with an high-power Full Colour (RGBW) LED featuring 4 LED channels (Red / Green / Blue / White); 3660 Total Lumens. The unit in available in two models: SCENA LED 80 PC FC, featuring a Ø 90 mm PC lens, and a long excursion 10°-76° linear zoom with high-efficiency optical system, enabling it to be used as a PC Beam or a very wide Wash (4245 Lux / 2 m). SCENA LED 80 FR FC, featuring a Ø 112 mm Fresnel lens, and a long excursion 14°-77° linear zoom (3864 Lux / 2 m) with high-efficiency optical system. SCENA LED 80 FC is a modern alternative to conventional lights, improving light quality, flexibility of use and installation, energy savings and component duration. The fixture doesn’t heat up and the projection is always flicker free. The dimming curves are similar to those of halogen lamps. The connectors are Powercon In/Out and 5 poles DMX In/Out. SCENA LED 80 FC is contained in a strong housing with folded edges, designed to resist all the rigors of continuous use. Also, the yoke has an exclusive round flange + clutch system which guarantees a perfect grip and safer operation.
PRODUCT CODES:
03.TS026.03.A SCENA LED 80 FC *PC lens *White finishing
03.TS026.44.A SCENA LED 80 FC *PC lens *Grey Silver finishing
03.TS026.46.A SCENA LED 80 FC *PC lens *Black finishing
03.TS026.03.F SCENA LED 80 FC *Fresnel lens *White finishing
03.TS026.44.F SCENA LED 80 FC *Fresnel lens *Grey Silver finishing
03.TS026.46.F SCENA LED 80 FC *Fresnel lens *Black finishing
LED Technology 1 x FULL RGBW LED; 3660 Lumens
Optical group PC version (Ø 90 mm PC lens), 4245 Lux / 2 m, 10° - 76° linear zoom FR version (Ø 112 mm Fresnel lens), 3864 Lux / 2 m, 14° - 77° linear zoom
Control 10 DMX channels (Default) 4 digit 7 segments LED display + 4 soft keys
Connectors Power supply: Powercon In & Out connectors DMX: 5 poles In & Out connectors
Power supply Electronic full-range 90-260Vac , 50/60 Hz Consumption: max 90W
Weight
4 Kg (PC version) 3,7 Kg (FR version)
Page 6
6
DIMENSIONS
5- ACCESSORIES
As standard
1 x User’s Manual 1 x POWERCON male cable connector (D.T.S. Code 0520P014) 1 x XLR 5 pins male cable connector (D.T.S. Code 0508B028) 1 x XLR 5 pins female cable connector (D.T.S. Code 0508B027) 1 x Filterframe for SCENA COMPACT *Black finish (D.T.S. Code 02M00422.46)
Optional (on request)
- “C” Clamp G50 (Max. Load. 10 Kg) *Black finish (D.T.S. Code 0521A012)
- “C” Clamp G60 (Max. Load. 50 Kg) *Black finish (D.T.S. Code 0521A004)
- Barndoor for SCENA COMPACT *Black finish (D.T.S. Code 03.TA206)
Page 7
7
6- IMPORTANT SAFETY INFORMATION
6.1 Fire prevention:
It is permissible to place the unit on normally flammable surfaces. Suitable for mounting on normally flammable materials surfaces greater than 200°C with some combustion time lag. Minimum distance from the closest illuminable surface: 30 cm. Replace any blown or damaged fuses only with those of identical value (2AT).
6.2 Prevention from electric shock:
High voltage is present inside the unit. Unplug the unit prior to performing any operation which involves touching the inside of the unit. This equipment must be grounded, do not connect to non-grounded supplies. The use of a thermal magnetic circuit breaker is recommended for each SCENA LED 80 FC unit. Use only AC supplies 90-260V , 50-60 Hz. SCENA LED 80 FC should never be located in position exposed to rain or in areas of extreme humidity. A good air ventilation is essential for proper equipment work.
6.3 Safety:
The external surface of the unit may exeed 50°C; never handle the unit until at least 5 minutes have elapsed since the unit was turned off. Never install the unit in an enclosed area lacking sufficient air flow. The ambient temperature should not exeed 40°C and should not be lower than -10°C.
6.4 Waste Electrical and Electronic Equipment (WEEE) directive:
The machine, accessories and packaging should be sorted for environmental-friendly recycling. For EC countries: according to the European Directive 2002/96/EC for Waste Electrical and Electronic Equipment and its implementation into national right, luminaires that are no longer usable must be collected separately and disposed of in an environmentally correct manner.
!
Page 8
8
7- INPUT / OUTPUT CONNECTIONS
FUSE 2AT
DMX OUTPUT XLR 5 Pins Female Panel Connector
MAINS AC
INPUT 90-260V, 50/60 Hz
DMX INPUT XLR 5 Pins Male Panel Connector
DISPLAY PANEL
MAINS AC
OUTPUT 90-260V, 50/60 Hz
MAX 16A
Page 9
9
5
3
4 2
1
1=GND 2=DATA­3=DATA+
CONTROLLER S T A N D A R D D M X 5 1 2
DMX OUT DMX OUT
DMX IN DMX IN
DMX OUT
DMX IN
DMX OUT
8- DMX SIGNAL CONNECTION:
The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or between units must be carried out using a two pair screened ø 0.5 mm. Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to the DMX IN plug of the second one. In this way, all the projectors are cascade connected.
If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX reception problem For Installations where long distance DMX cable connections are needed, we
suggest to use a DMX terminator. The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3. The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
Page 10
10
8.1 DMX addresses
SCENA LED 80 FC can be controlled with 10 DMX channels (Default). In order to use the unit in 10 DMX channels mode, set the following addresses on the mixer:
Projector 1 A001 Projector 2 A011 If you want to select the next projector, just add “10” Projector 3 A021 ….. A…. projector 6 A051
8.2 Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now controlled by the new DMX address.
TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now controlled by the new DMX address.
9- FIRMWARE UPDATING
To update the software version of the SCENA LED 80 FC you need:
- D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008)
- USB-DMX Driver for the D.T.S. RED BOX interface
- D.T.S. Firmware upgrade utility” program installed on PC
- Latest firmware release available for SCENA LED 80 FC unit
Updating the software version.
Please follow the procedure below to perform the update:
1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.
2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
4. Send the new software version into the unit by using D.T.S. Firmware upgrade Utility program.
Page 11
11
Up-Down
MENU
ENTERUp-Down
Up-DownENTER
Up-DownENTER
ENTER
ENTER
ENTER
ENTER
Up-Down
Up-Down
MENU
ENTER
Up-Down
ENTER
Up-Down
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
Up-Down
ENTER
Up-Down
ENTER
Standard mode enabled: (Default).
Extended mode enabled: Rainbow effects on MACRO channel.
10- DISPLAY FUNCTIONS
DISPLAY FUNCTIONS
The SCENA LED 80 FC display panel shows all the available functions. Using these functions, it is possible to change some of the parameters and add some functions. Changing the D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections. NOTE: the symbol shows which key has to be pushed to obtain the desired function.
Software version 5.13
REVERSE DISPLAY Reverses display's reading depending on the mounting position (on the ground or suspended).
DISPLAY STAND-BY To turn off the display (after 5 seconds) Or leave it always on.
DMX MODE To select DMX mode: 10 DMX channels mode (default), 6 DMX channel mode, 15 DMX channels mode, “WALL” mode,
“M4CH” mode, “RGBA” mode or 1 DMX
channel mode.
MACRO MACRO Function, enable channel mapping macro rainbow effects STD (default)
Suspended Position
Floor Position
Display Off
Display Always on
Default DMX Mode 10 Channels
1 channel mode
6 DMX channels mode
15 DMX channels mode
“WALL” (6 channels mode)
“M4CH” (5 channels mode)
RGBA (4 channels mode)
Page 12
12
With BOOST active, the LED’S current is set to Max value. (30% more gain compared to BOOST Off) Default = Disabled
Up-Down
MENU
ENTER
Up-Down
Up-Down
Up-Down
Up-DownENTER
ENTER
ENTER
Up-Down
Up-Down
Up-DownENTER
Up-DownENTER
Up-DownENTER
ENTER
ENTER
ENTER
ENTER
Up-DownENTER
ENTER
ENTER
LED RGBW Min/Max, Smooth, Compression, Sync and Boost level values settings
RGBW MINIMUM VALUE This menu allows to select the minimum levels for Red, Green, Blue and White
RGBW MAXIMUM VALUE This menu allows to select the maximum levels for Red, Green, Blue and White
These settings have priority on Master Dimmer channel
SMOOTH VALUE This menu allows to select the value of the delay (in milliseconds) for Dimmer channel reaction to DMX or Program variation. Off = 25 ms Instant response to DMX variation. 20 = 250 ms Smooth response to DMX variation.
COMPRESSION This menu allows to select between Linear current output or Quadratic current output for LEDs Default = Quadratic
SYNC This menu allows to adjust the PWM frequency value (Hz) in order to reduce flickering in the process of your camera recordings
BOOST DRIVING This menu allows to increase the
LED’s current from 350mA to
500mA
Linear = Linear Current output
Quadratic = Linear light output
Range: 0-100
Range = Off-20 Default = 4
Range = 610 Hz – 20 KHz Default = 610 Hz
Boost mode activated
Boost mode deactivated
Page 13
13
Up-DownENTER ENTER
Up-DownENTER
Up-DownENTER
ENTER
ENTER
ENTER
ENTER
MENU Up-Down
ENTER
MENU
Up-Down
Up-DownENTER ENTER
Up-Down
ENTER
ENTER
ENTER
Up-Down
ENTER
ENTER
Up-Down
Up-DownENTER ENTER
AUTOMATIC MODE Automatic demo game without DMX controller
ChPr Chase with 16 steps previously created in REC MODE Speed and Wait time selectable by user
CUPr RGBW values selectable by user
Rainbow (rAIn) Rainbow colours effect. Speed time selectable by user
CU01-CU16 Color Macros as on DMX channel 9 (MACRO)
WHITE MACROS 16 macros for White color from 2800K to 6500K
DIMMER Dimmer level selectable by user as on DMX channel 2 (DIMMER) Dimmer level is active for all the programs and macros
SHUTTER Shutter level selectable by user as on DMX channel 1 (SHUTTER) Shutter level is active only for CU01/CU16 and Wh01/Wh16 macros
ESC Esc from Automatic Mode Menu
REC MODE In DMX Recorder Mode,it is possible to create and store the scenes of the ChPr by using an external DMX controller. The unit must be set to 10 channels mode.
Page 14
14
ENTER
MENU Up-Down
Up-DownENTER
Up-Down
DMX Recorder Mode For the programming of ChPr by using a DMX controller, besides the 10 channels necessary to control the unit a further 3 DMX channels are needed. So that in RECORDER mode (via DMX) the unit will need 13 channels to be correctly programmed. The three new DMX channels are:
DMX channel 11 = SCENES channel From 0-10 = no function (r001) From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016)
DMX channel 12 = EDIT channel:
-From 0-19 = no function
-From 20-234 the unit runs the configuration given by the received input DMX values. With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene.
-From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene. With the channel REC it is possible to record the selected scene as last scene.
DMX channel 13 = RECORDING channel Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has been recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene. If ChPr is not closed, by indicating the last scene ( Edit channel between 235-255), in playback mode all 16 scenes will be played through even if not programmed
MENU
Up-Down Up-DownENTER
ENTER
ENTER
INFRARED MODE Infrared remote control. By activating Ir Mode, it will be possible to navigate trought the unit functions by using the D.T.S. infrared remote control (D.T.S. Code: 0514L008)
Note: External infrared remote sensor needed (D.T.S. Code: 03.LA.016)
NOT IMPLEMENTED ON SCENA LED 80 FC
SLAVE MODE Slave mode for ChPr program. All slave units will be synchronised with master unit, running their own Chpr program.
Page 15
15
MENU Up-Down
Up-DownEN TER
Up-DownEN TER
ENTER
ENTER
ENTER
WIRELESS DMX
Wireless DMX enabled / disabled. By activating WDMX MODE, it will be possible to control SCENA LED 80 FC via D.T.S. ANTENNA Wireless DMX Transmitter (cod. 03.E1271). Active only on SCENA LED 80 FC with Wireless on board
Wireless Enabled
Wireless Disabled
UNLINK = LOG OUT
Logging on SCENA LED 80 FC (WIRELESS DMX must be enabled on SCENA LED 80 FC unit)
To log on the SCENA LED 80 FC in the WIRELESS system simply press and quickly release the function button on the transmitter. The transmitter will start flashing rapidly red/green scanning for new free receivers / SCENA LED 80 FC units. When a SCENA LED 80 FC logs on to the transmitter the LINK green light on transmitter starts to flash rapidly. After approximately 10 seconds the transmitter will jump back to normal mode and continue transmitting data. The SCENA LED 80 FC now try to synchronize to the transmitter. When synchronized to the transmitter, 2 different modes are possible:
1. Antenna transmitter has detected and transmits a DMX signal, in this mode a solid green light is seen on the transmitter and solid display is seen on SCENA LED 80 FC.
2. No DMX signal connected, the Antenna transmitter will flash red/green; display blinking on SCENA LED 80 FC.
To log SCENA LED 80 FC off from a transmitter simply select UNLINK function under WIRELESS DMX MENU and press ENTER.
When SCENA LED 80 FC is logged off, the display is blinking, meaning its available for log in on a new transmitter.
Logging out a SCENA LED 80 FC Select UNLINK function under WIRELESS DMX MENU and press ENTER.
When SCENA LED 80 FC is logged off the display is blinking, meaning its available for log in on a new transmitter.
Logging out all SCENA LED 80 FC units linked to a transmitter Press and hold the function button of the transmitter for about 3 seconds. When the display is blinking on
SCENA LED 80 FC, it mean that the units are logged out.
Transmitter, Status LED Flashing red/green, no dmx connected. Solid green, dmx signal detected and transmitted. Fast flashing red/green, log in mode (every free SCENA LED 80 FC unit, not logged in to any other transmitter, will be logged on)
SCENA LED 80 FC Status Display blinking = not logged on to a transmitter (free). Solid display = logged on to a transmitter and receiving dmx data.
Page 16
16
ENTER
Up-DownENTER
Up-Down
MENU
ENTER
ENTER
ENTER
ENTER
MENU Up-Down
Up-DownEN TER
ENTER
Up-DownEN TER
ENTER
ENTER
EMERGENCY Emergency operating mode. By setting Emergency mode, it will be possible to select Dimmer intensity level that will then ran if DMX signal is missing or not available. Usefull for Emergency EXIT illumination on public areas.
ENTERENTER
Up-Down
MENU
ENTERENTER
Up-Down
MENU
.
DEFAULT SETTING To restore default settings
TEMPERATURE Internal unit temperature visualisation
Internal unit temperature (° Celsius)
LIFE TIME This menu shows the total unit life time and the LED life time
SOFTWARE Software version
Default = OFF
ENTER
Up-Down
MENU
. .
Page 17
17
11- DMX PROTOCOL
10 CHANNELS MODE (Default) 1 SHUTTER
2 DIMMER 3 RED 4 GREEN 5 BLUE 6 WHITE 7 WHITE PRE-PROGRAMMED 8 CTC 9 MACRO 10 FUNCTIONS
DMX CHANNEL
1
Parameter: SHUTTER
DMX range
Value
Mid Point
DMX
value
Move Range
(degrees)
Mode
Option
Function
000-009
5
Black-out
010-019
14
Open
020-029
24
Black-out
030-119
Strobe at variable speed from slow
to fast (3,27 s – 30 ms)
120-149
Pulse open at variable speed from
slow to fast (42,6 s – 120 ms)
150-179
Pulse close at variable speed from
slow to fast (42,6 s – 120 ms)
180-204
192
Random Strobe
205-229
218
Full Independent Random Strobe
230-234
Red, Yellow, Cyan and Blue colour
effects at variable speed
235-255
245
Open
DMX CHANNEL
2
Parameter: DIMMER
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
dimmer
DMX CHANNEL
3
Parameter: RED
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
4
Parameter: GREEN
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
Page 18
18
DMX CHANNEL
5
Parameter: BLUE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
6
Parameter: WHITE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
7
Parameter: WHITE PRE-PROGRAMMED
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-055
23
No Function
056-105
80
Full (Red-Green-
Blue at Full)
106-155
130
White DTS
IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE RECALL (DMX range value 000-079)
156-205
180
Custom White
Recall
206-255
225
White CTC
(Channel 8 CTC
enabled 256
color temp.
Correction
Macros: 2800°K
– 6500°K)
IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE CREATE (DMX range value 080-160)
156-205
180
Custom White
Create (RGB
levels selectable
by DMX)
206-255
225
White CTC
(Channel 8 CTC
enabled 256
color temp.
Correction
Macros: 2800°K
– 6500°K)
DMX CHANNEL
8
Parameter: CTC (Colour Temperature Correction)
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
IF CHANNEL 7 (WHITE PRE-PROGRAMMED) = WHITE CTC (DMX range value 206-255)
000-255
256 colour temp. Correction
Macros: 0=2800°K / 128=4500°K
/ 255=6500°K
IF CHANNEL 7 (WHITE PRE-PROGRAMMED) = NO FUNCTION (DMX range value 000-055)
000-255
NO FUNCTION
Page 19
19
DMX CHANNEL
9
Parameter: MACRO
IF:
DMX range
Value
Mid Point
DMX value
Move Range
(degrees)
Mode
Option
Function
000-014
No Function
015-029
Macro 1
030-044
Macro 2
045-059
Macro 3
060-074
Macro 4
075-089
Macro 5
090-104
Macro 6
105-119
Macro 7
120-134
Macro 8
135-149
Macro 9
150-164
Macro 10
165-179
Macro 11
180-194
Macro 12
195-209
Macro 13
210-225
Macro 14
226-239
Macro 15
240-255
Macro 16
DMX CHANNEL
9
Parameter: MACRO
IF:
DMX range
Value
Mid Point
DMX value
Move Range
(degrees)
Mode
Option
Function
000-014
No Function
015-022
Macro 1
023-030
Macro 2
031-038
Macro 3
039-046
Macro 4
047-054
Macro 5
055-062
Macro 6
063-070
Macro 7
071-078
Macro 8
079-086
Macro 9
087-094
Macro 10
095-102
Macro 11
103-110
Macro 12
111-118
Macro 13
119-126
Macro 14
127-134
Macro 15
135-142
Macro 16
143-150
Rainbow Speed 1 (1 Sec.)
151-158
Raibow Speed 2 (5 Sec.)
159-166
Rainbow Speed 3 (10 Sec.)
167-174
Rainbow Speed 4 (20 Sec.)
175-182
Rainbow Speed 5 (30 Sec.)
183-190
Rainbow Speed 6 (60 Sec.)
191-198
Rainbow Speed 7 (120 Sec.)
199-206
Rainbow Speed 8 (180 Sec.)
207-214
Random Speed 1 (0,5 Sec.)
215-222
Random Speed 2 (1 Sec.)
223-230
Random Speed 3 (2 Sec.)
231-238
Random Speed 4 (5 Sec.)
239-246
Random Speed 5 (10 Sec.)
247-255
Random Speed 6 (30 Sec.)
PLEASE CHECK PAGE 11
PLEASE CHECK PAGE 11
Page 20
20
DMX CHANNEL
10 Parameter: FUNCTIONS (Recall, Create and Store the Custom white)
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-079
Custom White
Recall (Enable
CH 7 for Custom
white Recall)
080-160
Custom White Create (Enable
CH 7 for Custom
white Creation)
161-255
Custom White
Store (Store the
Custom White
created)
“WALL” 6 CHANNELS MODE (For use with DTS Wall mounted DMX controller 0514L007)
Up-DownMENU ENTERUp-Down
ENTER
6 CHANNELS
1 GREEN 2 RED 3 BLUE 4 DIMMER 5 NOT USED 6 SHUTTER
DMX CHANNEL
1
Parameter: GREEN
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
2
Parameter: RED
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
3
Parameter: BLUE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
Page 21
21
DMX CHANNEL
4
Parameter: DIMMER
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
dimmer
DMX CHANNEL
5
Parameter: NOT USED
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
No Function
DMX CHANNEL
6
Parameter: SHUTTER
DMX range
Value
Mid Point
DMX
value
Move Range
(degrees)
Mode
Option
Function
000-009
5
Black-out
010-019
14
Open
020-029
24
Black-out
030-119
Strobe at variable speed from slow
to fast (3,27 s – 30 ms)
120-149
Pulse open at variable speed from
slow to fast (42,6 s – 120 ms)
150-179
Pulse close at variable speed from
slow to fast (42,6 s – 120 ms)
180-204
192
Random Strobe
205-229
218
Full Independent Random Strobe
230-234
Red, Yellow, Cyan and Blue colour
effects at variable speed
235-255
245
Open
“M4CH” 5 CHANNELS MODE 1 DIMMER
2 RED 3 GREEN 4 BLUE 5 WHITE
DMX CHANNEL
1
Parameter: DIMMER
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
dimmer
DMX CHANNEL
2
Parameter: RED
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
Page 22
22
DMX CHANNEL
3
Parameter: GREEN
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
4
Parameter: BLUE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
5
Parameter: WHITE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
4 CHANNELS MODE 1 RED
2 GREEN 3 BLUE 4 WHITE
DMX CHANNEL
1
Parameter: RED
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
2
Parameter: GREEN
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
3
Parameter: BLUE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
4
Parameter: WHITE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
Page 23
23
1 CHANNEL MODE 1 DIMMER
DMX CHANNEL
1
Parameter: DIMMER
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
Dimmer
15 CHANNELS MODE 1 SHUTTER
2 DIMMER 3 DIMMER FINE 4 RED 5 RED FINE 6 GREEN 7 GREEN FINE 8 BLUE 9 BLUE FINE 10 WHITE 11 WHITE FINE 12 WHITE PRE-PROGRAMMED 13 CTC 14 MACRO 15 FUNCTIONS
DMX CHANNEL
1
Parameter: SHUTTER
DMX range
Value
Mid Point
DMX
value
Move Range
(degrees)
Mode
Option
Function
000-009
5
Black-out
010-019
14
Open
020-029
24
Black-out
030-119
Strobe at variable speed from slow
to fast (3,27 s – 30 ms)
120-149
Pulse open at variable speed from
slow to fast (42,6 s – 120 ms)
150-179
Pulse close at variable speed from
slow to fast (42,6 s – 120 ms)
180-204
192
Random Strobe
205-229
218
Full Independent Random Strobe
230-234
Red, Yellow, Cyan and Blue colour
effects at variable speed
235-255
245
Open
DMX CHANNEL
2
Parameter: DIMMER
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
dimmer
Page 24
24
DMX CHANNEL
3
Parameter: DIMMER FINE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
Dimmer
DMX CHANNEL
4
Parameter: RED
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
5
Parameter: RED FINE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
6
Parameter: GREEN
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
7
Parameter: GREEN FINE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
8
Parameter: BLUE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
9
Parameter: BLUE FINE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
Page 25
25
DMX CHANNEL
10 Parameter: WHITE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
11 Parameter: WHITE FINE
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-255
Proportional
colour
DMX CHANNEL
12 Parameter: WHITE PRE-PROGRAMMED
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-055
23
No Function
056-105
80
Full (Red-Green-
Blue at Full)
106-155
130
White DTS
IF CHANNEL 15 (FUNCTIONS) = CUSTOM WHITE RECALL (DMX range value 000-079)
156-205
180
Custom White
Recall
206-255
225
White CTC
(Channel 13
CTC enabled
256 color temp.
Correction
Macros: 2800°K
– 6500°K)
IF CHANNEL 15 (FUNCTIONS) = CUSTOM WHITE CREATE (DMX range value 080-160)
156-205
180
Custom White
Create (RGB
levels selectable
by DMX)
206-255
225
White CTC
(Channel 13
CTC enabled
256 color temp.
Correction
Macros: 2800°K
– 6500°K)
DMX CHANNEL
13 Parameter: CTC (Colour Temperature Correction)
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
IF CHANNEL 12 (WHITE PRE-PROGRAMMED) = WHITE CTC (DMX range value 206-255)
000-255
256 colour temp. Correction
Macros: 0=2800°K / 128=4500°K
/ 255=6500°K
IF CHANNEL 12 (WHITE PRE-PROGRAMMED) = NO FUNCTION (DMX range value 000-043)
000-255
NO FUNCTION
Page 26
26
DMX CHANNEL
14 Parameter: MACRO
IF:
DMX range
Value
Mid Point
DMX value
Move Range
(degrees)
Mode
Option
Function
000-014
No Function
015-029
Macro 1
030-044
Macro 2
045-059
Macro 3
060-074
Macro 4
075-089
Macro 5
090-104
Macro 6
105-119
Macro 7
120-134
Macro 8
135-149
Macro 9
150-164
Macro 10
165-179
Macro 11
180-194
Macro 12
195-209
Macro 13
210-225
Macro 14
226-239
Macro 15
240-255
Macro 16
DMX CHANNEL
14 Parameter: MACRO
IF:
DMX range
Value
Mid Point
DMX value
Move Range
(degrees)
Mode
Option
Function
000-014
No Function
015-022
Macro 1
023-030
Macro 2
031-038
Macro 3
039-046
Macro 4
047-054
Macro 5
055-062
Macro 6
063-070
Macro 7
071-078
Macro 8
079-086
Macro 9
087-094
Macro 10
095-102
Macro 11
103-110
Macro 12
111-118
Macro 13
119-126
Macro 14
127-134
Macro 15
135-142
Macro 16
143-150
Rainbow Speed 1 (1 Sec.)
151-158
Raibow Speed 2 (5 Sec.)
159-166
Rainbow Speed 3 (10 Sec.)
167-174
Rainbow Speed 4 (20 Sec.)
175-182
Rainbow Speed 5 (30 Sec.)
183-190
Rainbow Speed 6 (60 Sec.)
191-198
Rainbow Speed 7 (120 Sec.)
199-206
Rainbow Speed 8 (180 Sec.)
207-214
Random Speed 1 (0,5 Sec.)
215-222
Random Speed 2 (1 Sec.)
223-230
Random Speed 3 (2 Sec.)
231-238
Random Speed 4 (5 Sec.)
239-246
Random Speed 5 (10 Sec.)
247-255
Random Speed 6 (30 Sec.)
PLEASE CHECK PAGE 11
PLEASE CHECK PAGE 11
Page 27
27
DMX CHANNEL
15 Parameter: FUNCTIONS (Recall, Create and Store the Custom white)
DMX range
Value
Mid Point DMX
value
Move Range
(degrees)
Mode
Option
Function
000-079
Custom White
Recall (Enable
CH 12 for
Custom white
Recall)
080-160
Custom White Create (Enable
CH 12 for
Custom white
Creation)
161-255
Custom White
Store (Store the
Custom White
created)
Page 28
28
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.
D.T.S. Illuminazione s.r.l. – Via Fagnano Selve 10-12-14 47843
Misano Adriatico (RN) Italia
Tel.: +39 0541 611131. Fax + 39 0541 611111
info@dts-lighting.it www.dts-lighting.it
0517I243
MADE IN ITALY
ISO 9001:2008
D.T.S. quality system
is certified to the
ISO 9001:2008 standard
D.T.S. products are designed and manufactured at the D.T.S. plants in italy
*0517I243*
Loading...