DTS NICK NRG1200 CT User Manual

D.T.S. Illuminazione s.r.l.

Via Fagnano Selve 10/12/14 47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it http://www.dts-lighting.it

Made in Italy

CT

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1-SYMBOLS 4 2- GENERAL WARNING 4 3- GENERAL WARRANTY CONDITION 4 4- TECHNICAL FEATURES 5 5- TECHNICAL SPECIFICATIONS 7 6- ACCESSORIES 7 7- IMPORTANT SAFETY INFORMATION 8

7.1 Fire prevention

7.2 Prevention of electric shock

7.3 Safety

7.4 Level of protection against the penetration of solid and liquid objects 8- VOLTAGE AND FREQUENCY 9 9- INSTALLATION 9

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature 10- MAINS CONNECTION 11

10.1 Protection 11- DMX SIGNAL CONNECTION 12

11.1 DMX Addresses

11.2 Selecting the DMX address 12- FIRMWARE UPDATING 13 13- DISPLAY FUNCTIONS 14 14- PERIODIC CLEANING 23 15- PERIODIC CONTROLS 23 16- DMX PROTOCOL 24

4

1- SYMBOLS Graphic symbols used on this manual

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK

RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE

UNIT ON INFLAMMABLE SURFACES”

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE TO BE KEPT BETWEEN THE DEVICE

AND THE LIT OBJECT

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important information regarding safety during installation , use and maintenance. The device is not for domestic use and must be installed by a qualified electrician or experienced person. Always disconnect the device from the mains before maintenance. The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing material defects.

F

!

0,5M

5

4- TECHNICAL FEATURES

Overview

NICK NRG 1200 CT is the most efficient LED moving head wash light ever produced. The exceptional brightness / consumption ratio makes NICK NRG 1200 CT a truly “green” fixture. NICK NRG 1200 CT is equipped with 30 high-power Full White LEDs, 5.600 °K. NICK NRG 1200 CT features three interchangeable lens fittings: Spot, Medium Flood and Wide Flood and ultra-fast silent Pan / Tilt.

Applications:

NICK NRG 1200 CT is suitable for top professional applications, such as tours and special events.

Product codes:

03.LDR008.FW12 NICK NRG 1200 CT Full White *Spot lenses *Black finish

03.LDR008.FW25 NICK NRG 1200 CT Full White *Medium flood lenses *Black finish

03.LDR008.FW45 NICK NRG 1200 CT Full White *Wide flood lenses *Black finish

03.LDR008.FW12WS NICK NRG 1200 CT Full White *Spot lenses *With Wireless on board *Black finish

03.LDR008.FW25WS NICK NRG 1200 CT Full White *Medium flood lenses *With Wireless on board *Black finish

03.LDR008.FW45WS NICK NRG 1200 CT Full White *Wide flood lenses *With Wireless on board *Black finish

LED Technology * 30 Full White LEDs (5.600 °K)

Optical group

* Three interchangeable lenses sets: Spot, Medium Flood and Wide Flood * Uniform projection on surfaces

Interface / Control / Programming * Multi-function OLED graphic colour display + 4 soft keys: control / management /

monitoring of the main parameters * Controlled via DMX 512 and RDM standard digital communication protocols * Wireless ready; Ethernet ready * Internal operating system updatable via D.T.S. RED BOX interface via “D.T.S. firmware upgrade utility” program on windows based PC

6

DMX

20 DMX channels

Pan & Tilt

* 16-bit movement resolution * Ultra-fast movement: Pan 540° (2 sec.); Tilt 270° (1,2 sec.) * Selectable speed ranges

Power supply * Electronic full-range AC 90-260 V 50 / 60 Hz

* Power consumption: 90 V – 3,7 A – 340 W ; 120 V – 2,83 A – 340 W ; 230 V – 1,47 A - 340 W ; 260 V – 1,3 A – 340 W

Connectors

* DMX: 4 XLR connectors (3 poles In / Out; 5 poles In / Out) by Neutrik * Power supply: POWERCON In / Out connectors by Neutrik

Operating ambient temperature

-10° / 40°

Weight

9,5 Kg

International certifications

Certification CE; LED Class: Class 2 LED product

7

5- TECHNICAL SPECIFICATIONS Dimensions

Packaging Dimensions (LxWxH) 530 x 430 x 414 mm Weight: 12 Kg

Unit Dimensions (LxWxH) 369x218x497 mm Weight: 9,5 Kg

6- ACCESSORIES As standard

• 1 x POWERCON male cable connector (cod. 0520P014)

• 1 x XLR 5 Pins Male cable connector by Neutrik (cod. 0508B066)

• 1 x XLR 5 Pins Female cable connector by Neutrik (cod. 0508B065)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (cod. 0521A014)

• User’s manual

Optional (on request) Flight case

• Professional Flight case for 4 units; compartment for accessories, swivel wheels, cover with hinges with-stay, dishes on cover for piling, 8 handles (2 eachside) (cod. 0521C051.1) Wireless DMX receiver retrofit

• Wireless DMX Receiver Card with INDOOR IP20 omnidirectional 2dBi antenna included (cod.03.LA.126)

Clamps / safety wires

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg)

(cod. 0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn 1 couple (2 pieces)

(Cod. 02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

369 mm

306 mm

4

9

7

m

4 1 3

m m

218 mm

8

7- IMPORTANT SAFETY INFORMATION

7.1 Fire prevention:

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 0,5 MT.

-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

7.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head.

-The level of technology inherent in the NICK NRG 1200 CT requires the assistance of specialised personnel for all servicing. Please refer to an authorised D.T.S. service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

7.3 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at least 10 minutes have elapsed since the projector was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should not exceed 40°C.

7.4 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid objects is IP 20.

F

!

0,5M

9

8- VOLTAGE AND FREQUENCY

The NICK NRG 1200 CT can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

NICK NRG 1200 CT may be either floor or ceiling mounted. For floor mounting installations, the NICK NRG 1200 CT is supplied with four rubber mounting feet on the base. For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface. The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to move or shake whilst the NICK NRG 1200 CT is moving. Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the NICK NRG 1200 CT by using the Fast Lock “C” clamps provided in the box.

9.1- Safety cable

We recommend the use of a safety cable or chain connected to the NICK NRG 1200 CT and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable or chain can bear the weight of the entire unit. You may attach the safety chain/cord to the attachment point (A) located on the base of the fixture, as shown in the picture below.

!

SAFETY CHAIN/CORD ATTACHMENT POINT

A

10

9.2 Protection against liquids

The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur.

9.3- Movement

Ultra-fast movement: Pan 540° (2,0 sec.); Tilt 270° (1,2 sec.)

WARNING Do not place any object in the path

of the projector’s movement

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 0,5 MT.

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans. These should, under no circumstances, be blocked or obstructed whilst the projector is in operation. Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.

F

!

0,5M

540°

270°

11

10- MAINS CONNECTION

NICK NRG 1200 CT operate at 90-260 VOLT 50-60 Hz. Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 2 amps at 230V, or 5 amps at 90 V. Strict adherence to regulatory norms is strongly recommended.

MAINS AC OUTPUT 90 – 260 V 50 / 60 Hz (16A Max)

MAX 10 NICK NRG 1200 UNITS @ 230V MAX 5 NICK NRG 1200 UNITS @ 120V

MAINS AC INPUT 90 – 260 V 50 / 60 Hz

Wireless DMX Receiver Retrofit (Cod. 03.LA.126)

FUSE 5A T 5X20

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each NICK NRG 1200 CT.

!

Cod. 03.LDR008.FW12 Cod. 03.LDR008.FW25 Cod. 03.LDR008.FW45

Cod. 03.LDR008.FW12WS Cod. 03.LDR008.FW25WS Cod. 03.LDR008.FW45WS

12

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy. The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one. This way, all the projectors are cascade connected. NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX terminator. The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor between pin 2 and 3. The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

5

3

4 2

1

1=GND 2=DATA3=DATA+

CONTROLLER S TA ND AR D D M X 5 1 2

DMX OUT

DMX OUT DMX IN

DMX IN

DMX IN DMX OUT

13

11.1-DMX Addresses

NICK NRG 1200 CT can be controlled with 20 DMX channels. In order to use the unit in 20 channels, set the following addresses on the mixer:

Projector 1 A001 Projector 2 A021 If you want to select the next projector, just add “20” Projector 3 A041 ….. A…. projector 6 A101

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.

TRICKS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.

12- FIRMWARE UPDATING

Warning:

This procedure require a base knowledge of computer applications and Windows Hyperterminal program. Please refer to an authorised D.T.S. service centre.

To update the software version of the NICK NRG 1200 you need: D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008). USB-DMX Driver for the D.T.S. RED BOX interface. D.T.S. Firmware upgrade utility program. (The driver and the installation procedure are available in our web site www.dts-lighting.it)

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using D.T.S. Firmware upgrade utility program.

!

14

13- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The NICK NRG 1200 CT display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections. NOTE: the symbol shows which key has to be pushed to obtain the desired function.

MENU

ENTER

DOWN

UP

DISPLAY

2dBi IP20 omnid.

antenna

DMX INDMX

OUT

WIRELESS DMX RECEIVER RETROFIT

03.LA.126

03.LDR008.FW12

03.LDR008.FW25

03.LDR008.F12

03.LDR008.F25

MAINS AC INPUT

90-260V 50 / 60Hz

MAINS AC OUTPUT

90-260V 50 / 60 Hz

(16A Max)

DMX OUT

DMX IN

DMX OUT

DMX IN

Cod. 03.LDR008.FW12WS Cod. 03.LDR008.FW25WS Cod. 03.LDR008.FW45WS

Cod. 03.LDR008.FW12 Cod. 03.LDR008.FW25 Cod. 03.LDR008.FW45

15

13- DISPLAY FUNCTIONS

Software version 1.10

Display

DISPLAY POSITION / STAND BY Display Position:

Reverses display's reading depending on the mounting position (on the ground or suspended).

Display Standby: To turn off the display (after 5 seconds) or leave it always on.

DMX Set

DMX MODE / MACRO DMX Mode 20 channels

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

AA

DISPLAY

MENU ENTER DOWN

UP

OFF

DISPLAY

POSITION

STANDBY

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

STD

DMX SET

MACRO

Display Position ON THE GROUND (Default) SUSPENDED

Display Standby OFF = Display Standby disabled (Default) ON = Display goes OFF after 5 seconds

DMX Mode 20 channels

MACRO (Colour MACROS active only on NICK NRG 1200 FULLCOLOUR, NICK NRG 1200 CT will show only different white light intensity ) Macro Mode: STD = Standard (Default) EXT = Extended; enable rainbow effects on Macro channel (DMX ch 16)

MACRO (Active only on NICK NRG 1200 FULLCOLOUR NICK NRG 1200 CT will show only different white light intensity) STD = Standard mode enabled (Default) EXT = Extended; enable rainbow effects on Macro channel (DMX ch 16)

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

20 channels

DMX SET

DMX MODE

16

13- DISPLAY FUNCTIONS

LED NICK NRG 1200 FULLCOLOUR:

RGBA MINIMUM VALUES This menu allow to select the minimum levels for Red, Green, Blue and Amber/White

NICK NRG 1200 CT:

4 x WHITE MINIMUM VALUES This menu allow to select the minimum levels for Red = White 1, Green = White 2, Blue = White 3 and Amber/White = White 4

NICK NRG 1200 FULLCOLOUR:

RGBA MAXIMUM VALUES This menu allow to select the maximum levels for Red, Green, Blue and Amber/White These settings have priority on Master Dimmer (DMX channel 9)

NICK NRG 1200 CT:

4 x WHITE MAXIMUM VALUES This menu allow to select the maximum levels for Red = White 1, Green = White 2, Blue = White 3 and Amber/White = White 4 These settings have priority on Master Dimmer (DMX channel 9)

SMOOTH VALUE This menu allow to select the value of the delay (in milliseconds) for RGBA (NICK NRG 1200 FULLCOLOUR) or WHITE (NICK NRG 1200 CT) and Dimmer channels reaction to DMX or program variation. 4 = 25 ms delay (Fast response) 20 = 250 ms delay (Slow response)

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

LED

RED MIN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

LED

GREEN MIN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

LED

BLUE MIN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0

LED

AMBER MIN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

4

LED

SMOOTH

NICK NRG 1200 FULLCOLOUR / CT:

RED / WHITE 1 Min default = 0 RED / WHITE 1 Max default = 100

NICK NRG 1200 FULLCOLOUR / CT:

BLUE / WHITE 3 Min default = 0 BLUE / WHITE 3 Max default = 100

NICK NRG 1200 FULLCOLOUR / CT:

GREEN / WHITE 2 Min default = 0 GREEN / WHITE 2 Max default = 100

NICK NRG 1200 FULLCOLOUR / CT:

AMBER / WHITE 4 Min default = 0 AMBER / WHITE 4 Max default = 100

SMOOTH Range = Off – 20 Default = 4

17

13- DISPLAY FUNCTIONS

GAMMA CORRECTION This menu allow to select between Linear current output or Quadratic current output for LEDs Default = Quadratic

OUTPUT FREQUENCY This menu allow to adjust the PWM frequency value (Hz) in order to reduce flickering in the process of your camera recordings

BOOST DRIVING This menu allow to increase the LED’s current from 350 mA to 500 mA

AUTO AUTOMATIC MODE

Automatic demo games without DMX controller

(Colour MACROS active only on NICK NRG 1200 FULLCOLOUR, NICK NRG 1200 CT will show only different white light intensity )

STEP 01/16 Chase with 16 steps previously created in REC MODE Speed time, Wait time, Dimmer, Pan and Tilt values selectable by user.

PERSONAL COLOURS RGBA, Dimmer, Shutter, Pan and Tilt values selectable by user.

RAINBOW Rainbow colours effect. Speed time, Dimmer, Shutter, Pan and Tilt values selectable by user.

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

AUTO

SURE?

Menu - NO

Enter - YES

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

01/16

AUTO-PROGRAM

STEP

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

120

AUTO-PERS.COL.

RED

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0010

AUTO-RAINBOW

SPEE

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

QUAD

LED

GAMMA CORR.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

610

LED

OUTPUT FREQ.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

ON

LED

BOOST

GAMMA CORRECTION Linear = Linear current output Quadratic = Linear light output (default)

OUTPUT FREQUENCY Range = 610 Hz – 10KHz Default = 610 Hz

BOOST With BOOST active, the LEDs current is set to 500 Ma (30% more gain) Default = Enabled

By setting all the units connected to the MASTER to DMX address 1, them will be synchronized with the Master unit following the chase selected on it including TIME, WAIT, Pan and Tilt position of the MASTER unit.

18

13- DISPLAY FUNCTIONS

FIXED COLOURS Sixteen Colour Macros as on “MACRO” channel. Dimmer, Shutter, Pan and Tilt it, values selectable by user.

WHITE MACROS (Active only on NICK NRG 1200 FULLCOLOUR) Sixteen macros for White colour (active only on NICK NRG 1200 FULLCOLOUR); White Macros for NICK NRG 1200 CT: Different white light Intensity. Dimmer, Shutter, Pan and Tilt values selectable by user.

SLAVE

SLAVE MODE SETTING This menu allow to set the NICK NRG 1200 CT as slave unit. DMX signal must be present from MASTER unit (set in AUTO MODE) in order to ran the units in SLAVE mode. By setting all the SLAVE units connected to the MASTER, to DMX address 1, them will be synchronized with the Master unit following the chase selected on it, but running their own Pan and Tilt position.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

1

AUTO-WHITE

WHITE NO.

20 ch

DMX SET

DMX MODE

1

AUTO-FIXED COL.

COLOR

MENU ENTER DOWN

UP

MENU ENTER DOWN

UP

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

128

SLAVE

PAN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

SLAVE

SURE?

Menu - NO

Enter - YES

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

128

SLAVE

TILT

By setting all the units connected to the MASTER to DMX address 1, them will be synchronized with the Master unit following the chase selected on it including TIME, WAIT, Pan and Tilt position of the MASTER unit.

The SLAVE unit receive DMX signal from the MASTER unit. By setting all the SLAVE units connected to the MASTER, to DMX address 1, them will be synchronized with the Master unit following the chase selected on it, but running their own Pan and Tilt position.

19

13- DISPLAY FUNCTIONS WIRELESS

WIRELESS DMX Wieless DMX enabled / disabled. By activating WDMX MODE, it will be possible to control NICK NRG 1200 CT via D.T.S. ANTENNA Wireless DMX Transmitter (cod.

03.E1271).

Wireless DMX Receiver Kit (Cod. 03.LA.126) on NICK NRG 1200 CT is available on request.

Logging on NICK NRG 1200 CT (WIRELESS DMX must be enabled on the unit). To log on the NICK NRG 1200 CT in the WIRELESS system simply press and quickly release the

function button on the transmitter . The transmitter will start flashing rapidly red/green scanning for new free receivers / NICK NRG 1200 CT units. When a NICK NRG 1200 CT logs on to the transmitter the LINK green light on transmitter starts to flash rapidly. After approximately 10 seconds the transmitter will jump back to normal mode and continue transmitting data. The NICK NRG 1200 CT now try to synchronize to the transmitter. When synchronized to the transmitter, 2 different modes are possible:

1. Antenna transmitter has detected and transmits a DMX signal, in this mode a solid green light is seen on the transmitter and solid display is seen on NICK NRG 1200 CT.

2. No DMX signal connected, the Antenna transmitter will flash red/green; display blinking on NICK NRG 1200 CT.

To log off NICK NRG 1200 CT from a transmitter simply select UNLINK function under WIRELESS DMX MENU and press ENTER. When NICK NRG 1200 CT is logged off the display is blinking, meaning its available for log in on a new transmitter.

Logging out a NICK NRG 1200 CT. Select UNLINK function under WIRELESS DMX MENU and press ENTER. When NICK NRG 1200 CT is logged off the display is blinking, meaning its available for log in on a new transmitter.

Logging out all NICK NRG 1200 CT linked to a transmitter. Press and hold the function button of the transmitter for about 3 seconds. When the display is blinking on NICK NRG 1200 CT, it mean that the units are logged out.

Transmitter, Status LED. Flashing red/green, no dmx connected. Solid green, dmx signal detected and transmitted. Fast flashing red/green, log in mode (every free NICK NRG 1200 CT unit, not logged in to any other transmitter, will be logged on)

NICK NRG 1200 CT Status. Display blinking, not logged on to a transmitter (free). Solid display, logged on to a transmitter and receiving dmx data.

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

WIRELESS

UNLINK

20 ch

DMX SET

DMX MODE

OFF

WIRELESS

SELECTION

MENU ENTER DOWN

UP

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

ON

WIRELESS

SELECTION

MENU ENTER DOWN

UP

MENU ENTER DOWN

UP

Up-Down

Menu

Up-DownENTER

ENTER

WIRELESS DMX SYSTEM DISABLED (Default)

WIRELESS DMX SYSTEM ENABLED

UNLINK = LOG OUT

20

13- DISPLAY FUNCTIONS

EMERGENCY

EMERGENCY Emergency operating mode. By setting Emergency mode, it will be possible to select one of the 16 pre-programmed WHITE cues (active only on NICK NRG 1200 FULLCOLOUR; NICK NRG 1200 CT will show only different white light intensity) that will then ran if DMX signal is missing or not available. Useful for Emergency EXIT illumination on public areas. Dimmer level and Pan&Tilt values selectable by user.

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

OFF

EMERGENCY

SELECTION

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

1

EMERGENCY

WHITE

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

255

EMERGENCY

DIMMER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

128

EMERGENCY

PAN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

128

EMERGENCY

TILT

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

ON

EMERGENCY

SELECTION

EMERGENCY Disabled = Default

EMERGENCY Enabled

WHITE (1-16) Default = WHITE 1

DIMMER Default = 255

PAN Default = 128

TILT Default = 128

21

13- DISPLAY FUNCTIONS

DEFAULT SET

DEFAULT SETTINGS To restore default settings

TEMPER. °C

TEMPERATURE Unit temperature

TIME

LIFE TIME This menu show the total UNIT life time and the RGBA (NICK NRG 1200 FULLCOLOUR) or the R = WHITE 1, G = WHITE 2, B = WHITE 3, A = WHITE 4 (NICK NRG 1200 CT) life time

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

Up-Down

Menu

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

028.7

TEMPER. °C

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

13 Hr - 08 min

TIME

UNIT

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0 Hr - 08 min

TIME

RED

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0 Hr - 08 min

TIME

GREEN

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0 Hr - 08 min

TIME

BLUE

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

0 Hr - 08 min

TIME

AMBER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

DEFAULT SET

SURE?

Menu - NO

Enter - YES

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

DEFAULT SET

22

13- DISPLAY FUNCTIONS

SYSTEM PAN INVERSION / TILT INVERSION /

PAN SPEED / TILT SPEED / FAN MAX SPEED / RESET BY DMX / MOTORS FIRMWARE UPGRADE.

PAN INVERSION This menu allows to set the Pan movement. Normal or Reversed.

TILT INVERTION This menu allows to set the Tilt movement. Normal or Reversed.

PAN SPEED Pan Speed control (1-8)

TILT SPEED Tilt Speed control (1-8)

FAN MAX SPEED This menu’ allow to select the internal fans speed.

RESET BY DMX This menu’ allow to enable / disable the Motors reset control (Pan&Tilt) via DMX.

MOTORS FIRMWARE UPGRADE This menu’ allow to upgrade the firmware for Pan&Tilt circuit boards.

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

NORM

SYSTEM

PAN INVERSION

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

NORM

SYSTEM

TILT INVERSION

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

SYSTEM

MOTORS

FW UPGRADE

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

100%

SYSTEM

FAN MAX SPEED

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

ENAB

SYSTEM

RESET BY DMX

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

4

SYSTEM

PAN SPEED

MENU ENTER DOWN

UP

DMX SET

DMX MODE

MENU ENTER DOWN

UP

4

SYSTEM

TILT SPEED

PAN INVERSION Default = NORM

TILT INVERSION Default = NORM

PAN SPEED CONTROL Default = 4

TILT SPEED CONTROL Default = 4

FAN MAX SPEED 50% - 100% Default = 100%

RESET BY DMX Enable: Motors reset enabled via DMX (Default) Disabled: Motors reset disabled via DMX Now: Instant motors reset.

MOTORS FIRMWARE UPGRADE Pan&Tilt circuit boards firmware upgrade.

23

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

Id 0D1307C1

v1.10 Jun 13 2012

SOFTWARE

LED

MENU ENTER DOWN

UP

20 ch

DMX SET

DMX MODE

MENU ENTER DOWN

UP

Pan/Tilt v.13

SOFTWARE

Motors

13- DISPLAY FUNCTIONS

SOFTWARE SOFTWARE

LEDs circuit board software, MOTORS circuit boards software (Pan&Tilt)

14- PERIODIC CLEANING

Front lenses Glass

The dust can reduce the luminous output substantially. Regularly clean the front lenses glass using a soft cotton cloth, dampened with a specialist glasses cleaning solution.

Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. If necessary, clean the fans and air passages more frequently.

15- PERIODIC CONTROLS

Mechanical parts

Periodically check all mechanical parts and the gaskets, replacing them if necessary.

Electrical components

Check all electrical components for correct earthing and proper attachment of all connectors, refastening if necessary.

Attention: Disconnect mains power prior to removing the

projector housing.

Fuse replacement

Locate the fuse, which protect the electronics, in the base of the NICK NRG 1200 CT. Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.

Attention: Disconnect mains power prior to removing the

projector housing.

!

Up-Down

Menu

Up-DownENTER

ENTER

LEDs CIRCUIT BOARD SOFTWARE

MOTORS CIRCUIT BOARDS SOFTWARE (PAN&TILT)

24

16- DMX PROTOCOL

20 CHANNELS MODE

1 PAN msb 540° 2 PAN Isb 3 TILT msb 270° 4 TILT Isb 5 SPEED MOVEMENT 6 NO FUNCTION 7 NO FUNCTION 8 SHUTTER 9 DIMMER 10 RED = WHITE 1 11 GREEN = WHITE 2 12 BLUE = WHITE 3 13 WHITE = WHITE 4 14 WHITE PRE-PROGRAMMED (Not Active) 15 CTC 16 MACRO (Not Active) 17 FUNCTION (Recall, Create and Store the Custom white) 18 NO FUNCTION 19 NO FUNCTION 20 RESET

DMX CHANNEL

1

Parameter: PAN msb

DMX CHANNEL

2

Parameter: PAN lsb

DMX CHANNEL

3

Parameter: TILT msb

DMX CHANNEL

4

Parameter: TILT lsb

DMX CHANNEL

5

Parameter: SPEED MOVEMENT

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-010

Standard

011-025

Fast movement

026-127

Vector mode

from fast to

slow

128-247

Variable time

reaction to

DMX signal (fast

to slow)

248-255

Slow reaction

time to DMX

signal

25

DMX CHANNEL

6

Parameter: NO FUNCTION

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

NO FUNCTION

DMX CHANNEL

7

Parameter: NO FUNCTION

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

NO FUNCTION

DMX CHANNEL

8

Parameter: SHUTTER

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-009

Black-out

010-019

Open

020-029

Black-out

030-119

Strobe (from 3.27 s to 30 ms)

120-149

Pulse up (from 42.6 s to 120 ms)

150-179

Pulse down (from 42.6 s to 120 ms)

180-204

Random strobe (Dimmer, Red,

Green, Blue, Amber channels

active)

205-229

Full independent Random Strobe

(Dimmer, Red, Green, Blue, Amber

channels disabled)

230-255

Open

DMX CHANNEL

9

Parameter: DIMMER

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-007

Black-out

008-255

Proportional

dimmer

DMX CHANNEL

10 Parameter: RED = WHITE 1

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

26

DMX CHANNEL

11 Parameter: GREEN = WHITE 2

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

DMX CHANNEL

12 Parameter: BLUE = WHITE 3

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

DMX CHANNEL

13 Parameter: WHITE = WHITE 4

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

DMX CHANNEL

14 Parameter: WHITE PRE-PROGRAMMED (Not Active on NICK NRG 1200 CT)

NICK NRG 1200 CT will show only different white light intensity

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-055

23

No Function

056-105

80

Full (Red-Green-

Blue at Full)

106-155

130

White DTS

156-205

180

Custom White

Create (RGB

levels selectable

by DMX)

206-255

230

White CTC

(Channel 15

CTC enabled)

DMX CHANNEL

15 Parameter: CTC (Colour Temperature Correction)

NICK NRG 1200 CT will show only different white light intensity

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

IF CHANNEL 14 WHITE PREPROGRAMMED = WHITE CTC (DMX range value 206 – 255)

000-255

Linear control

temperature

correction.

NICK NRG 1200

FULLCOLOR:

0 = 2700°K /

255 = 8000°K.

NICK NRG 1200 CT

FULLWHITE:

different white

light intensity

27

DMX CHANNEL

16 Parameter: MACRO (NICK NRG 1200 CT WILL SHOW ONLY DIFFERENT WHITE LIGHT INTENSITY)

IF: DMX SET MACRO STD (Please refer to page 15 for details)

000-014

No Function

015-029

Macro 1

030-044

Macro 2

045-059

Macro 3

060-074

Macro 4

075-089

Macro 5

090-104

Macro 6

105-119

Macro 7

120-134

Macro 8

135-149

Macro 9

150-164

Macro 10

165-179

Macro 11

180-194

Macro 12

195-209

Macro 13

210-225

Macro 14

226-239

Macro 15

240-255

Macro 16

DMX CHANNEL

16 Parameter: MACRO (NICK NRG 1200 CT WILL SHOW ONLY DIFFERENT WHITE LIGHT INTENSITY)

IF: DMX SET MACRO EXT (Please refer to page 15 for details)

000-014

No Function

015-024

Macro 1

025-034

Macro 2

035-044

Macro 3

045-054

Macro 4

055-064

Macro 5

065-074

Macro 6

075-084

Macro 7

085-094

Macro 8

095-104

Macro 9

105-114

Macro 10

115-124

Macro 11

125-134

Macro 12

135-144

Macro 13

145-154

Macro 14

155-164

Macro 15

165-174

Macro 16

175-184

Rainbow Speed 1 (6 Sec.)

185-194

Rainbow Speed 2 (15 Sec.)

195-204

Rainbow Speed 3 (30 Sec.)

205-214

Rainbow Speed 4 (45 Sec.)

215-224

Rainbow Speed 5 (60 Sec.)

225-234

Rainbow Speed 6 (120 Sec.)

235-244

Rainbow Speed 7 (150 Sec.)

245-255

Rainbow Speed 8 (180 Sec.)

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

28

DMX CHANNEL

17 Parameter: FUNCTIONS (Recall, Create and Store the Custom white)

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

IF CHANNEL 14 WHITE PREPROGRAMMED = DMX range value 156 – 205)

000-079

Custom White

Recall

080-160

Custom White Create (Enable

Custom White

Creation)

161-255

Custom White

Store (Store the

Custom White

created)

DMX CHANNEL

18 Parameter: NO FUNCTION

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

NO FUNCTION

DMX CHANNEL

19 Parameter: NO FUNCTION

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

NO FUNCTION

DMX CHANNEL

20 Parameter: RESET

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-015

No Effect

016-255

Total Reset

(activation after

3 sec.)

29

NOTES

30

NOTES

31

NOTES

32

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.

D.T.S. Illuminazione s.r.l. – Via Fagnano Selve 10-12-14 47843

Misano Adriatico (RN) Italia

Tel.: +39 0541 611131. Fax + 39 0541 611111

info@dts-lighting.it www.dts-lighting.it

0517I195.CT

MADE IN ITALY

ISO 9001:2008

D.T.S. quality system

is certified to the

ISO 9001:2008 standard

D.T.S. products are designed and manufactured at the D.T.S. plants in italy

*0517I195.CT*