DTS FOS 100 WHITE 36, FOS 100 SOLO ON-OFF WHITE 36, FOS 100 SOLO WHITE 36 User Manual

FOS 100 WHITE 36

FOS 100 WHITE 36

FOS 100 SOLO ON-OFF WHITE 36

FOS 100 SOLO WHITE 36

User’s Manual rel 1.0

D.T.S. Illuminazione s.r.l. - ITALY
http://www.dts-lighting.it

GB

Made in Italy

1

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

FOS 100 WHITE 36

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

D.T.S.

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

D.T.S.

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

D.T.S.

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

D.T.S.

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S

D.T.S.

1- SYMBOLS

Graphic symbols used on this manual:

2

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK RISK

FOS 100 WHITE 36

!

LED 0,5 m

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS YOU CAN PLACE THE UNIT
ON NORMALLY FLAMMABLE SURFACES

THIS SYMBOL INDICATES THE MINIMUM
DISTANCE BETWEEN THE UNIT AND THE
ILLUMINATED OBJECTS

THIS SYMBOL INDICATES THE EUROPEAN
COMMUNITY DIRECTIVE 2002/96/EC ON
WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT (WEEE)

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important information regarding
safety during installation, use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or experienced person.
The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing material defects.

3

FOS 100 WHITE 36

4- TECHNICAL FEATURES

FOS 100 WHITE 36

D.T.S. Product codes:

03.LBB012E11WB10 FOS 100 WHITE 36 3000K Narrow lenses Black

03.LBB012E11WB25 FOS 100 WHITE 36 3000K Medium flood lenses Black

03.LBB012E11WB40 FOS 100 WHITE 36 3000K Wide flood lenses Black

03.LBB012E11WBE3 FOS 100 WHITE 36 3000K 15° x 40° lenses Black

03.LBB012E11WB02 FOS 100 WHITE 36 3000K 58° lenses Black

03.LBB012E11WB03 FOS 100 WHITE 36 3000K 77° lenses Black

03.LBB012E11WB14 FOS 100 WHITE 36 3000K ASY Spot lenses Black

03.LBB012E11WB11 FOS 100 WHITE 36 3000K ASY Wash lenses Black

Light source

36 x WHITE LEDs; Colour temperature: 2700K / 3000K / 4000K / 5600K
6500 Lumens; LEDs average lifespan: 70.000 hrs

Optical group

Narrow, Medium, Wide, 15° x 40°, 58°, 77°, ASY Spot, ASY Wash lenses set

Construction

FOS 100 WHITE 36 is made on extruded aluminium

Protection

IP 65 protection level

Connection

2 poles cable

Power supply

1050mA or 1400mA Constant current LED PSU
Electronic full-range 90-260 Vac 50-60 Hz

Power consumption

36W Max @ 350mA; 54W Max @ 500mA

Operating ambient temperature

-10° / 40°

Weight

5,5 Kg

Accessories

- 1050mA Constant current LED PSU (D.T.S. Code 0502T046)

- 1400mA Constant current LED PSU (D.T.S. Code 0502T050)

Dimensions

4

FOS 100 WHITE 36

5

FOS 100 WHITE 36

4- TECHNICAL FEATURES

FOS 100 SOLO ON-OFF WHITE 36

D.T.S. Product codes:

03.LBB001S11WB10 FOS 100 SOLO ON-OFF WHITE 36 3000K Narrow lenses Black

03.LBB001S11WB25 FOS 100 SOLO ON-OFF WHITE 36 3000K Medium flood lenses Black

03.LBB001S11WB40 FOS 100 SOLO ON-OFF WHITE 36 3000K Wide flood lenses Black

03.LBB001S11WBE3 FOS 100 SOLO ON-OFF WHITE 36 3000K 15° x 40° lenses Black

03.LBB001S11WB02 FOS 100 SOLO ON-OFF WHITE 36 3000K 58° lenses Black

03.LBB001S11WB03 FOS 100 SOLO ON-OFF WHITE 36 3000K 77° lenses Black

03.LBB001S11WB14 FOS 100 SOLO ON-OFF WHITE 36 3000K ASY Spot lenses Black

03.LBB001S11WB11 FOS 100 SOLO ON-OFF WHITE 36 3000K ASY Wash lenses Black

Light source

36 x WHITE LEDs; Colour temperature: 2700K / 3000K / 4000K / 5600K
6500 Lumens; LEDs average lifespan: 70.000 hrs

Optical group

Narrow, Medium, Wide, 15° x 40°, 58°, 77°, ASY Spot, ASY Wash lenses set

Construction

FOS 100 SOLO ON-OFF WHITE 36 is made on extruded aluminium

Protection

IP 65 protection level

Control system

ON-OFF

Connection

Mains AC Power cable

Power supply

Electronic full-range 90-260 Vac 50-60 Hz

Power consumption

54W Max

Operating ambient temperature

-10° / 40°

Weight

6,5 Kg

Dimensions

6

FOS 100 WHITE 36

7

FOS 100 WHITE 36

4- TECHNICAL FEATURES

FOS 100 SOLO IP20 WHITE 36 (on request)

Light source

36 x WHITE LEDs; Colour temperature: 2700K / 3000K / 4000K / 5600K
6500 Lumens; LEDs average lifespan: 70.000 hrs

Optical group

Narrow, Medium, Wide, 15° x 40°, 58°, 77°, ASY Spot, ASY Wash lenses set

Construction

FOS 100 SOLO IP20 WHITE 36 is made on extruded aluminium

Protection

IP 65 (LED bar); IP 20 (Power supply)

Control system

DMX 512

Connection

Power supply: POWERCON Female panel connectors (IN-OUT)
DMX: XLR 5 poles Male/Female panel connectors (IN-OUT)

Power supply

Z10 IP20 LED PSU
Electronic full-range 90-260 Vac 50-60 Hz

Power consumption

54W Max

Operating ambient temperature

-10° / 40°

Weight

7 Kg

Dimensions

8

FOS 100 WHITE 36

9

FOS 100 WHITE 36

4- TECHNICAL FEATURES

FOS 100 SOLO IP65 WHITE 36 (on request)

Light source

36 x WHITE LEDs; Colour temperature: 2700K / 3000K / 4000K / 5600K
6500 Lumens; LEDs average lifespan: 70.000 hrs

Optical group

Narrow, Medium, Wide, 15° x 40°, 58°, 77°, ASY Spot, ASY Wash lenses set

Construction

FOS 100 SOLO IP65 WHITE 36 is made on extruded aluminium

Protection

IP 65 protection level

Control system

DMX 512

Connection

Power supply: 3x1,5 sq mm cable (IN); HARTING Female panel connector (OUT)
DMX: HARTING 4 poles Male/Female panel connectors (IN-OUT)

Power supply

Z10 IP65 LED PSU
Electronic full-range 90-260 Vac 50-60 Hz

Power consumption

54W Max

Operating ambient temperature

-10° / 40°

Weight

7,5 Kg

Dimensions

10

FOS 100 WHITE 36

11

FOS 100 WHITE 36

5- IMPORTANT SAFETY INFORMATION

5.1 Fire prevention:

-It is permissible to place the unit on normally flammable surfaces.
Suitable for mounting on normally flammable material surfaces greater than 200°C with some
combustion time lag.

-Minimum distance between the unit and the illuminated objects: 0,5 m.

5.2 Prevention of electric shock:

-High voltage is present inside the unit.
Unplug the unit prior to performing any function which involves touching the inside of the fixture.

-A good earth connection is essential for proper functioning of the unit.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

LED 0,5 m

5.3 Safety:

-The external surface of the unit, at various points, may exceed 50°C.
Never handle the unit until at least 5 minutes have elapsed since the unit was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow.
The ambient temperature should not exceed 40°C.

5.4 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an outdoor appliance and its protection level against the penetration of
solid and liquid objects is IP 65.

5.5 Waste Electrical and Electronic Equipment (WEEE) directive:

The LED bar, accessories and packaging should be sorted for environmental-friendly recycling.
For EC countries: according to the European Directive 2002/96/EC for Waste Electrical and Electronic
Equipment and its implementation into national right, luminaires that are no longer usable must be
collected separately and disposed of in an environmentally correct manner.

!

!

6- CONNECTION

FOS 100 WHITE 36

FOS 100 WHITE 36 is provided with a 2 poles cable.

12

FOS 100 WHITE 36

-

(Blue)

+

(Brown)

FOS 100 SOLO ON-OFF WHITE 36

FOS 100 SOLO ON-OFF WHITE 36 is provided with a Mains AC Power cable.

Brown = L
Blue = N
Yellow/Green = GND

MAINS INPUT

90-260Vac 50-60Hz

13

6- CONNECTION

FOS 100 SOLO IP20 WHITE 36 (on request)

FOS 100 WHITE 36

MAINS INPUT

POWERCON Female

panel connector

LED OUT

DMX IN

XLR 5 poles male

panel connector

MAINS OUTPUT

POWERCON Female

panel connector

DMX OUT

XLR 5 poles female

panel connector

FOS 100 SOLO IP65 WHITE 36 (on request)

DMX IN

HARTING 4 poles male

panel connector

MAINS INPUT

3 x 1,5 sq mm cable

with cable gland

DMX OUT

HARTING 4 poles Female

panel connector

MAINS OUTPUT

HARTING Female

panel connector

14

FOS 100 WHITE 36

7- DMX SIGNAL CONNECTION

FOS 100 SOLO IP20 WHITE 36 (on request)

The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or
between units must be carried out using a two pair screened ø 0.5 mm.

Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX
connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN
projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to
the DMX IN plug of the second one.
In this way, all the projectors are cascade connected.

DMX INDMX IN

UNIT 2

DMX OUTDMX OUT

CONTROLLER
S T AN D A RD
D M X 5 1 2

5

4 2

3

1

1=GND
2=DATA­3=DATA+

DMX INDMX IN

UNIT 1

DMX OUTDMX OUT

P.S:
If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

5

4

3

120 ohm

2

1

OUT

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

PIN 3

PIN 2

15

FOS 100 WHITE 36

7- DMX SIGNAL CONNECTION

FOS 100 SOLO IP65 WHITE 36 (on request)

The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or
between units must be carried out using a two pair screened ø 0.5 mm.

Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX
connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN projector
plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to the DMX
IN plug of the second one.
In this way, all the projectors are cascade connected.

CONTROLLER
S T AN D AR D
D M X 5 1 2

5

4 2

1

1=GND
2=DATA-

3

3=DATA+

DMX INDMX IN

DMX OUTDMX OUT

DMX INDMX IN

DMX OUTDMX OUT

P.S:
If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male DMX cable connector with a 120 ohm resistor Between pin 2 and 3.
The DMX terminator must be plugged into the DMX out panel connector of the last unit connected to
the DMX line.

DMX

MALE CABLE
CONNECTOR

120 OHM

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE DMX CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

16

FOS 100 WHITE 36

8- DMX ADDRESS

FOS 100 SOLO IP20 WHITE 36 (on request)
FOS 100 SOLO IP65 WHITE 36 (on request)

FOS 100 SOLO IP20/IP65 WHITE 36 can be used in 8 different modes: 10 DMX channels mode
(default), 6 DMX channels mode (Shutter + Dimmer + RGBW), 15 DMX channels mode, WALL
mode (6 DMX channels; for use with DTS Wall mounted DMX controller 0514L007), M4CH mode (5
DMX channels; Dimmer + RGBW), RGBW mode (4 channels), 1 DMX channel mode or CUSTOM
DMX mode (not yet implemented).

In order to use the unit in 10 DMX channels mode (default) set the following addresses on the
mixer:

Projector 1 A001
Projector 2 A011 If you want to select the next projector, just add “10”
Projector 3 A021
….. A….
projector 6 A051

Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the
display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and
you get a faster selection.

9- DISPLAY FUNCTIONS

FOS 100 SOLO IP20 WHITE 36
FOS 100 SOLO IP65 WHITE 36

17

FOS 100 WHITE 36

MENU

DOWN

UP

ENTER

DISPLAY FUNCTIONS

The FOS 100 SOLO display panel shows all the available functions . Using these functions, it is
possible to change some of the parameters and add some functions. Changing the D.T.S. setting
can vary the functions of the unit so that it does not respond to the DMX 512 signal used to
control it. Carefully follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Software version 5.15

MENU

REVERSE DISPLAY
Reverses display's reading depending on
the mounting position
(On the ground or suspended).

DISPLAY STAND BY
To turn off the display (after 5 seconds)
or leave it always on.

ENTERUp-Down

Up-Down

Up-Down

Up-DownENTER

Up-DownENTER

Floor

position

Suspension

position

Display OFF

Display

always ON

ENTER

ENTER

ENTER

ENTER

Up-Down

DMX MODE
To select DMX mode: 10 DMX channels
mode (default), 6 DMX channels mode
(Shutter + Dimmer + RGBW), 15 DMX
channels mode, WALL mode (6 DMX
channels; for use with DTS Wall
mounted DMX controller 0514L007),
M4CH mode (5 DMX channels; Dimmer
+ RGBW), RGBW mode (4 channels), 1
DMX channel mode.

CUSTOM DMX mode (not yet
implemented) lets you set the parameters
for Shutter, Dimmer, Red, Green, Blue,
White, White pre-programmed, CTC,
Macro and Function to the desired DMX

Up-DownMENU ENTER

Up-Down

Up-Down

Up-Down

Up-Down

Up-Down

Up-Down

10 CHANNELS

6 CHANNELS

15 CHANNELS

WALL (6 CHANNELS)

M4CH (5 CHANNELS)

RGBA (4 CHANNELS)

1 CHANNEL

CUSTOM DMX MODE
NOT YET IMPLEMENTED

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

Up-DownENTER

Default DMX Mode = 10 CH

Shutter + Dimmer + RGBW

Dimmer + RGBW

Custom mode enabled

ENTER

Show Custom settings

ENTER

Parameters Setting on
Custom Mode

ENTER

Up-Down

MENU ENTER

MACRO
MACRO Function, enable channel
mapping macro rainbow effects
STD (default)

Up-Down

18

FOS 100 WHITE 36

Standard mode enabled:
(Default).

Up-DownENTER

ENTER

Extended mode enabled:
Rainbow effects on MACRO

ENTER

channel.

MENU

LED
RGBW Min/Max, Smooth, Compression,
Sync and Boost level values settings

RGBW MINIMUM VALUES
This menu allows to select the
minimum levels for Red, Green,
Blue and White

RGBW MAXIMUM VALUES
This menu allows to select the
maximum levels for Red, Green,
Blue and White

These settings have priority
on Master Dimmer channel

SMOOTH VALUE
This menu allows to select the
value of the delay (in milliseconds)
for RGBW and Dimmer channels
reaction to DMX or Program
variation.
Off=25 ms delay (Fast response)
20=250 ms delay (Slow response)

Up-Down

ENTERUp-Down

Up-DownENTER

Default = 0

Default = 255

Default = 0

Up-Down

Up-DownENTER

Default = 255

Default = 0

Up-Down

Up-DownENTER

Default = 255

Default = 0

Up-Down

Up-DownENTER

Default = 255

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

ENTER

COMPRESSION
This menu allows to select between
Linear current output or Quadratic
current output for LEDs
Default = Linear

SYNC
This menu allows to adjust the
PWM frequency value (Hz) in order
to reduce flickering in the process
of your camera recordings

BOOST DRIVING
This menu allows to increase the
LED’s current from 350 mA to 500 mA

Up-Down

Up-Down

Up-Down

Up-DownENTER

Up-DownENTER

Up-DownENTER

Up-DownENTER

Up-Down

Range = Off-20
Default = 4

ENTER

Off = 25 ms
Istant responce to DMX variation

20 = 250 ms
Smooth response to DMX variation

Linear = Linear
current output

ENTER

Quadratic =
Linear light

ENTER

output

Range = 610 Hz -10 KHz
Default = 610 Hz

Boost mode activated

Boost mode deactivated

ENTER

ENTER

With BOOST active, the LED’s
current is set to 500 mA (30%
more gain).
Default = Disabled

ENTER

Up-Down

MENU

AUTOMATIC MODE
Automatic demo game without
DMX controller

ChPr
Chase with 16 steps previously
created in REC MODE
Speed and Wait time selectable
by user

CUPr
RGB values selectable by user

Rainbow (rAIn)
Rainbow colours effect.
Speed time selectable by user

CU01-CU16
Color Macros as on DMX channel
8 (Macro)

WHITE MACROS
16 macros for White color from
2800K to 6500K

ENTER

19

Up-DownENTER ENTER

ENTER

ENTER

ENTER

Up-DownENTER ENTER

FOS 100 WHITE 36

Up-Down

Up-Down

Up-Down

ENTER

ENTER

DIMMER
Dimmer level selectable by user
as on DMX channel 2 (Dimmer)
Dimmer level is active for all the
programs and macros

SHUTTER
Shutter level selectable by user
as on DMX channel 1 (Shutter)
Shutter level is active only for

CU01/CU16 and Wh01/Wh16
macros

ESC
Esc from Automatic Mode Menu

Up-DownENTER ENTER

Up-DownENTER

ENTER

Up-Down

MENU

REC MODE

In DMX Recorder Mode,it is
possible to create and store the
scenes of the ChPr by using an
external DMX controller.
The unit must be set to 10
channels MODE

ENTER

ENTER

Up-DownENTER

ENTER

20

FOS 100 WHITE 36

DMX Recorder Mode
For the programming of ChPr by using a DMX controller, besides the 10 channels necessary to control the unit a further 3
DMX channels are needed.
So that in RECORDER mode (via DMX) the unit will need 13 channels to be correctly programmed.
The three new DMX channels are:

DMX channel 11 = SCENES channel
From 0-10 = no function (r001)
From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

DMX channel 12 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.
With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the
selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene.
With the channel REC it is possible to record the selected scene as last scene.

DMX channel 13 = RECORDING channel
Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has been
recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to
save the scene. If ChPr is not closed, by indicating the last scene ( Edit channel between 235-255), in playback mode all
16 scenes will be played through even if not programmed

Up-Down

MENU

SLAVE MODE
Slave mode for ChPr program.
All slave units will be
synchronised with master unit,
running their own Chpr program.

Up-Down

MENU

INFRARED MODE
Infrared remote control.
By activating Ir MODE, it will be
possible to navigate trought the
unit functions by using the D.T.S.
infrared remote control.
D.T.S. Code :0514L008

Up-Down

MENU

WIRELESS DMX
Wireless DMX enabled/disabled.

Wireless DMX receiver kit on FOS
100 is available on request.

ENTER

Up-DownENTER

Up-DownENTER

Up-Down

Up-DownENTER

ENTER

ENTER

NOTE:
External infrared remote sensor
needed.
D.T.S. Code :03.LA.016

NOT IMPLEMENTED ON FOS 100

ENTER

WIRELESS DMX Disabled
(Default)

WIRELESS DMX Enabled

ENTER

UNLINK = LOG OUT

Up-Down

MENU

FAN SPEED CONTROL
Internal Fan Speed control
selectable by user.
Range: OFF - 24 volt
Default : 12 volt

Up-Down

MENU

EMERGENCY
Emergency operating mode.
By setting Emergency mode, it
will be possible to select one of
the 16 preprogrammed WHITE
cues that will then ran if DMX
signal is missing or not available.
Usefull for Emergency EXIT
ilumination on public areas.

Up-DownENTER

ENTER

Fan Speed Control
Range: OFF - 24 volt
Default = 12 volt

Up-DownENTER

Up-DownENTER

ENTER

Default = OFF

ENTER

Default = White 1

Default = 255

ENTER

21

FOS 100 WHITE 36

Up-Down

MENU

DEFAULT
To restore default settings

Up-Down

MENU

TEMPERATURE
Internal Unit temperature
visualisation

Up-Down

MENU

LIFE TIME
This menu show the total UNIT life time
and the RGBW life time

Up-Down

MENU

TEST MODE
RGBW colours test with rainbow

ENTER

ENTERENTER

.

Up-DownENTER

ENTERENTER

ENTER

Internal Unit temperature.
(° Celsius)

NOT YET IMPLEMENTED

Up-Down

MENU

SOFTWARE
Software version

ENTER

.

.

22

10- DMX PROTOCOL

FOS 100 SOLO IP20 WHITE 36
FOS 100 SOLO IP65 WHITE 36

10 CHANNELS MODE (Default)

1 SHUTTER
2 DIMMER
3 RED (first 9 LEDs line)
4 GREEN (second 9 LEDs line)
5 BLUE (third 9 LEDs line)
6 WHITE (fourth 9 LEDs line)
7 WHITE PRE-PROGRAMMED (Useful for FOS FC o CT model)
8 CTC (Useful for FOS FC or CT model)
9 COLOURS MACRO (Useful for FOS FC or CT model)
10 FUNCTIONS (Useful for FOS FC or CT model)

FOS 100 WHITE 36

DMX CHANNEL

DMX range

Value

0-9
10-19
20-29
30-119

120-149
150-179
180-204
205-229
230-234
235-255

DMX CHANNEL

DMX range

Value

0-255

1

Mid point

DMX value

5
14
24

192
218

245

2

Mid point

DMX value

Parameter: SHUTTER

Move

range

Mode Option Function

(degrees)

Parameter: DIMMER

Strobe at variable speed from slow to fast (3,27 s - 30 ms)

Pulse open at variable speed from slow to fast (42,6 s - 120ms)

Pulse close at variable speed from slow to fast (42,6 s - 120ms)

Move

range

Mode Option Function

(degrees)

Black-out

Open

Black-out

Random Strobe (Master and RGBW active)

Random Strobe (Full)

Colour effects at variable speed

Open

Proportional dimmer

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

Mid point

DMX value

Parameter: RED (first 9 LEDs line)

3

Move

range

Mode Option Function

(degrees)

23

FOS 100 WHITE 36

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

Mid point

DMX value

Mid point

DMX value

Mid point

DMX value

Parameter: GREEN (second 9 LEDs line)

4

Move

range

Mode Option Function

(degrees)

Parameter: BLUE (third 9 LEDs line)

5

Move

range

Mode Option Function

(degrees)

Parameter: WHITE (fourth 9 LEDs line)

6

Move

range

Mode Option Function

(degrees)

DMX CHANNEL

DMX range Mid point

Value DMX value

0-55 23

56-105

106-155

7

80
130

Parameter: PRE-PROGRAMME WHITE (Useful for FOS FC or CT model)

Move

range

(degrees)

Mode Option Function

No Function

Full (Red-Green-Blue-White at Full)

White DTS

IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE RECALL (Dmx range value 0 - 79)

156-205

206-255

180

225

White CTC (Channel 8 CTC enabled
256 color temp. Correction Macros: 2800K - 6500K)

Custom White Recall

IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE CREATE (Dmx range value 80 - 160)

156-205

206-255

180

225

Custom White Create (RGBA levels selectable by DMX)

White CTC (Channel 8 CTC enabled
256 color temp. Correction Macros: 2800K - 6500K)

24

DMX CHANNEL

DMX range Mid point

Value DMX value

8

Parameter: CTC (Useful for FOS FC or CT model)

Move

range

(degrees)

Mode Option Function

IF CHANNEL 7 (White) = WHITE CTC (Dmx range value 206 - 255)

0-255

256 color temp. Correction Macros: 0 = 2800°K / 128 = 4500°K / 255 = 6500°K

IF CHANNEL 7 (White) = NO FUNCTION (Dmx range value 0 - 43)

0-255

DMX CHANNEL

9

Parameter: COLOUR MACROS (Useful for FOS FC or CT model)

No Function

FOS 100 WHITE 36

IF:

MENU

Up-Down

DMX range

Value

0-14
15-29
30-44
45-59
60-74
75-89
90-104

105-119
120-134
135-149
150-164
165-179
180-194

195-209
210-225

226-239
240-255

DMX value

ENTER

Mid point

Up-Down

(degrees)

Move
range

PLEASE CHECK PAGE 13

ENTER

Up-Down

ENTER

Mode Option Function

No Function
Macro 1
Macro 2
Macro 3

Macro

Macro 4
Macro

Macro 5
Macro

Macro 6
Macro

Macro 7
Macro

Macro 8
Macro

Macro 9
Macro

Macro 10
Macro

Macro 11
Macro

Macro 12

Macro

Macro 13
Macro

Macro 14
Macro

Macro 15
Macro 16

DMX CHANNEL

9

25

Parameter: COLOUR MACROS (Useful for FOS FC or CT model)

FOS 100 WHITE 36

IF:

Up-Down

MENU

DMX range

Value

0-14
15-22
23-30
31-38
39-46
47-54
55-62
63-70
71-78
79-86
87-94
95-102

103-110
111-118

119-126
127-134
135-142
143-150
151-158
159-166
167-174
175-182
183-190
191-198
199-206
207-214

215-222
223-230

231-238
239-246
247-255

DMX value

ENTER

Mid point

Up-Down

Up-Down

ENTER

Move

range Mode Option

(degrees)

PLEASE CHECK PAGE 13

ENTER

Function

No Function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8

Macro 9
Macro 10
Macro 11
Macro 12

Macro 13
Macro 14
Macro 15

Macro 16
Rainbow Speed 1 (1 Sec.)
Rainbow Speed 2 (5 Sec.)
Rainbow Speed 3 (10 Sec.)

Rainbow Speed 4 (20 Sec.)
Rainbow Speed 5 (30 Sec.)
Rainbow Speed 6 (60 Sec.)
Rainbow Speed 7 (120 Sec.)

Rainbow Speed 8 (180 Sec.)
Random Speed 1 (0.5 sec.)
Random Speed 2 (1 Sec.)
Random Speed 3 (2 Sec.)
Random Speed 4 (5 Sec.)
Random Speed 5 (10 Sec.)
Random Speed 6 (30 Sec.)

DMX CHANNEL

10

DMX range Mid point

Value DMX value

0-79

80-160

161-255

Parameter: FUNCTIONS (Recall, Create and Store the Custom white)

Move

range

(degrees)

Custom White Recall (Enable CH 7 for Custom white Recall)

Mode Option Function

Custom White Create (Enable CH 7 for Custom white Creation)

Custom White Store (Store the Custom White created )

11- WIRING DIAGRAMS

FOS 100 WHITE 36

26

FOS 100 WHITE 36

+

(Brown)

48Vdc

OUT

LED+ (Red)

-

(Blue)

LED- (Black)

90-260Vac

IN

1050mA or 1400mA

1050mA or 1400mA

constant current LED PSU

constant current LED PSU

L (Brown)

N (Blue)

The maximum number of FOS 100
WHITE 36 connectable to a 1050mA
or 1400mA Constant current LED PSU
is 1 piece.

The maximum distance between the
unit and the PSU should not exceed
15 meters.

Never connect or disconnect the
unit when the PSU is turned on.

FOS 100 SOLO ON-OFF WHITE 36

Brown = L
Blue = N
Yellow/Green = GND

MAINS INPUT

90-260Vac 50-60Hz

The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its
products without prior notice. D.T.S. assumes no responsibility for the use or application of the
products or circuits described herein.

MADE IN ITALY

ISO 9001:2008

D.T.S. quality system

is certified to the

ISO 9001:2008 standard

D.T.S. products are designed
and manufactured at the D.T.S.
plants in italy

*0517I253*

0517I253

D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy

Tel. [phone] Fax [phone] [e-mail] www.dts-lighting.it