DTS DELTA 8 Series, DELTA 8 WHITE + AMBER B, DELTA 8 FULL COLOUR B, DELTA 8 RGB B User Manual
DELTA 8 B
DELTA 8 WHITE + AMBER B
DELTA 8 FULL COLOUR B
DELTA 8 RGB B
User’s Manual Rel 1.0
D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it
GB
Made in Italy
2
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
DELTA 8 B
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
D.T.S.
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
D.T.S.
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
D.T.S.
sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
D.T.S.
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S
D.T.S.
3
DELTA 8 B
INDEX
1- SYMBOLS 4
2- GENERAL WARNING 4
3- GENERAL WARRANTY CONDITION 4
4- TECHNICAL FEATURES 5
5- TECHNICAL SPECIFICATIONS 5
6- ACCESSORIES 7
7- IMPORTANT SAFETY INFORMATION 8
7.1 Fire prevention
7.2 Prevention of electric shock
7.3 Safety
7.4 Level of protection against the penetration of solid and liquid objects
8- VOLTAGE AND FREQUENCY 9
9- INSTALLATION 9
9.1 Safety cable
9.2 Protection against liquids
9.3 Movement
9.4 Risk of fire
9.5 Forced ventilation
9.6 Ambient temperature
10- MAINS CONNECTION 10
10.1 Protection
11- DMX SIGNAL CONNECTION 11
11.1 DMX Addresses
11.2 Selecting the DMX address
12- FIRMWARE UPDATING 12
13- DISPLAY FUNCTIONS 13
14- AUTOMATIC OPERATION (AUTO) 20
15- PERIODIC CLEANING 21
16- PERIODIC CONTROLS 21
17- DMX PROTOCOL 22
1- SYMBOLS
Graphic symbols used on this manual
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC SHOCK RISK
4
DELTA 8 B
!
F
0,5M
2- GENERAL WARNING
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON
INFLAMMABLE SURFACES”
THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO
BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT
Read the instruction contained in this user manual carefully, as they give important information
regarding safety during installation , use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or experienced
person.
Always disconnect the device from the mains before replacing the lamp.
The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.
The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 36 months from the date of purchase against manufacturing material defects.
5
DELTA 8 B
4- TECHNICAL FEATURES
Overview
The DELTA 8 B is a self-contained high-output LED projector suitable for lighting and colouring large
surfaces.
The DELTA 8 B features a light body detachable from base (max distance 50m).
The DELTA 8 B provides a powerful colour synthesis engine: * 16 million colours (RGB, FULL COLOUR), *
linear colour temperature (2800°K to 6500°K).
The unit is available with interchangeable lenses sets offering a range of beam angles.
DELTA 8 RGB B: 108 x 1W P4 type RGB LEDs
DELTA 8 FULL COLOUR B: 36 Full Colour LEDs
DELTA 8 WHITE + AMBER B: 108 x 1W P4 type WHITE + AMBER LEDs
Applications
DELTA 8 B is ideal in various applications, such as: lighting shopping malls, libraries, museums,
exhibitions, clubs, restaurants, buildings, monuments, as well as special events, fashion displays, indoor
and outdoor.
5- TECHNICAL SPECIFICATIONS
LED technology
Delta 8 RGB B:108 x 1W P4 type RGB LEDs (36 Red, 36 Green, 36 Blue)
Delta 8 White + Amber B:108 x 1W P4 type White + Amber LEDs. (72 White, 36 Amber).
Delta 8 FULL COLOUR B: 36 x 3W P5 II Full colour LEDs
LEDs average lifespan: 100.000 hours
Colour temperature variable on a linear range (2800°K ÷ 6500°K)
No infrared emission; no ultraviolet emission
Optical units
4 interchangeable lenses sets available (Spot, Medium flood, Wide flood, Very wide flood)
User interface
LED display
Independent operation
Fully programmable via built-in user interface
Master or Slave capability (chains of up to 32 interconnected units)
Remote control
Remotely controlled by cable or wireless (USITT DMX512)
USITT DMX 512 serial digital protocol (reception / transmission)
9 DMX channels
Protection
IP65 protection level
Hardware configuration
Light body detachable from base. (max distance 50m)
Power supply
Full range AC 90-260V, 50-60Hz power supply
Power consumption Delta 8 RGB B / Delta 8 White + Amber B:
* 90 V - 2,1 A - 190 W
* 120 V - 1,58 A - 190 W
* 230 V - 0,83 A - 190 W
* 260 V - 0,73 A - 190 W
Power consumption Delta 8 FULL COLOUR B:
* 90 V - 2,44 A - 220 W
* 120 V - 1,83 A - 220 W
* 230 V - 0,95 A - 220 W
* 260 V - 0,85 A - 220 W
Movements (horizontal/pan – vertical/tilt axes)
Mechanical movement 180° Pan / 180° Tilt
Thermal
Operating ambient temperature - 10° / + 40°
Finishes
Black or white finish
Certification and Safety
Certification CE;
LED Class
Class 2 LED product
Weight
18 Kg
6
DELTA 8 B
Dimensions
Unit Dimensions (LxWxH)
459x311x511mm
Weight:
18 Kg
Packaging Dimensions (LxWxH)
x 500 x 660 mm
530
Weight:
24 Kg
7
DELTA 8 B
6- ACCESSORIES
As standard
• 2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• ABS cover protection for Main AC and DMX cables on the base (cod. 0511C083)
• User’s manual
Optional (on request)
Lenses sets (black colour assembly)
Delta 8 RGB B / White + Amber B:
Lenses set Spot (cod. 03.LK021) ,Lenses set MEDIUM flood (cod. 03.LK.022), Lenses set WIDE flood
(cod. 03.LK.023), Lenses set VERY WIDE flood (cod. 03.LK.020)
Delta 8 FULL COLOUR B:
Lenses set Spot (cod. 03.LK098) ,Lenses set MEDIUM flood (cod. 03.LK.099), Lenses set WIDE flood
(cod. 03.LK.100), Lenses set VERY WIDE flood (cod. 03.LK.020)
Flight cases
Flight case for 1 DELTA with no wheels (cod. 0521C029), Flight case with wheels for 2 DELTA
(cod. 0521C030)
Wireless DMX receivers retrofits
• Wireless DMX Receiver Card with OUTDOOR IP65 omnidirectional 2dBi antenna included
(cod.03.LA.012)
Clamps / safety wires
• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)
• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)
• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)
• Omega clamp with “Fast Lock” connection 1⁄4 turn 1 couple (2 pieces) (Cod. 02K00467)
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)
Cables / connectors
Extension Cable with M/F M16 9-pole connectors, 5 m (cod. 03.LA.121.05)
Extension Cable with M/F M16 9-pole connectors, 10 m (cod. 03.LA.121.10)
Extension Cable with M/F M16 9-pole connectors, 20 m (cod. 03.LA.121.20)
Extension Cable with M/F M16 9-pole connectors, 30 m (cod. 03.LA.121.30)
Extension Cable with M/F M16 9-pole connectors, 50 m (cod. 03.LA.121.50)
Cable for DELTA B, 9xAWG22 (cod. 0509C085)
9-pin M16 IP67 cable connector for Delta B, Male (cod. 0508B105)
9-pin M16 IP67 cable connector for Delta B, Female (cod. 0508B106)
ANTENNA Outdoor 2dBi Omni-directional, radiation (HxV) 360°x360° (cod. 0508A040)
IR remote control for Delta 8 (cod. 0514L008)
8
DELTA 8 B
7- IMPORTANT SAFETY INFORMATION
7.1 Fire prevention:
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 MT.
-Minimum distance from the closest illuminable surface: 0,5 MT.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
7.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head.
-The level of technology inherent in the DELTA 8 B requires the assistance of specialised personnel for all
servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
F
0,5M
7.3 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C.
Never handle the unit until at least 10 minutes have elapsed since the
projector was turned off.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
7.4 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid objects is IP 65.
!
!
9
8- VOLTAGE AND FREQUENCY
The DELTA 8 B can operate at 90-260 VOLT 50 or 60 Hz.
9- INSTALLATION
DELTA 8 B may be either floor or ceiling mounted.
For floor mounting installations, the DELTA 8 B is supplied with four rubber mounting feet on the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake if moving head units are attached to it.
Two 1/4 turn Fast Locks connections placed in the base of the units allow to hang the DELTA 8 B by
using the Fast Lock ‘C’ clamps provided in the box.
.
DELTA 8 B
!
LOCK
9.1- Safety cable
We recommend the use of a safety chain/cord connected to the DELTA 8 B and to the suspension truss
in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron
cable or chain can bear the weight of the entire unit.
You may attach the safety chain/cord to the attachment points (A) located on the base of the fixture, as
shown in the picture below.
SAFETY CHAIN/CORD
A
SAFETY CHAIN/CORD
ATTACHMENT POINT
A
SAFETY CHAIN/CORD
A
!
A
9.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.
A
10
DELTA 8 B
9.3- Movement
Pan 180° (mechanical movement), Tilt 180° (mechanical movement)
Tilt
180°
!
WARNING
Do not place any object in the path
of the projector’s movement
9.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
Pan
180°
F
Minimum distance from the object being illuminated is 0,5 MT.
9.5- Forced ventilation
You will note, on inspection, that the unit feature a thermal dissipator on the head. This should, under no
circumstances, be blocked or obstructed whilst the projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
9.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.
10- MAINS CONNECTION
DELTA 8 B operate at 90-260 VOLT 50-60 Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession
correctly matches the mains supply available.
For connection purposes, ensure that your plug
is capable of supporting 1 amps at 230V,
Or 2,5 amps at 90 V.
Strict adherence to regulatory norms
is strongly recommended.
0,5M
DMX IN
DMX 512
1 GND
2 DATA3 DATA +
DMX OUT
)
90-260 Vac
50/60 Hz
Mains
90-260V AC 50 / 60Hz
8
9
Pin1
7
6
2
LED OUTPUTS
5
4
ANTENNA
WIRELESS
DMX
10.1- Protection
!
The use of a thermal magnetic circuit breaker is recommended for each DELTA 8 B.
A good earth connection is essential for the correct operation of the projector.
11
DELTA 8 B
11- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR
5 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable ground to
the XLR chassy.
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it
to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
This way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
CONTROLLER
STANDARD DMX 512
5
4 2
1
1=GND
2=DATA3=DATA+
3
DMX OUT
)
DMX IN
DMX OUT
90-260 Vac
50/60 Hz
8
9
Pin1
7
6
2
LED OUTPUTS
5
4
ANTENNA
WIRELESS
DMX
)
DMX IN
DMX OUT
90-260 Vac
50/60 Hz
8
9
Pin1
7
6
2
LED OUTPUTS
5
4
ANTENNA
WIRELESS
DMX
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out cable connector) of the DMX line.
5
4
3
120 ohm
2
1
OUT
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
PIN 3
PIN 2
Loading...