DTS DELTA R FULL COLOR, DELTA R TRILED, DELTA 5-7 RGB R User Manual

Download

Page 1

DELTA R

DELTA R FULL COLOR

DELTA R TRILED

DELTA 5-7 RGB R

User’s Manual Rel 1.5

D.T.S. Illuminazione srl - ITALY http://www.dts-lighting.it

Made in Italy

Page 2

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

DELTA R

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

D.T.S.

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

D.T.S.

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

D.T.S.

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

D.T.S.

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S

D.T.S.

Page 3

DELTA R

INDEX:

1- TECHNICAL FEATURES 4 2- IMPORTANT SAFETY INFORMATION 8

2.1 Fire prevention

2.2 Prevention of electric shock

2.3 Protection against direct light radiation

2.4 Safety

2.5 Level of protection against the penetration of solid and liquid matter

3- VOLTAGE AND FREQUENCY 9 4- INSTALLATION 9

4.1 Safety cable

4.2 Risk of fire

4.3 Ambient temperature

5- MAINS CONNECTION 10

5.1 Protection:

6- DMX SIGNAL CONNECTION 10

6.1 DMX Addresses

6.2 Selecting the DMX address

7- MOVEMENT 11 8- DISPLAY FUNCTIONS 12

9- OPENING UP THE PROJECTOR HOUSING 25

9.1 Arms

9.2 base

10- CHANGHING THE LENSES 26 11- PERIODIC CLEANING 28 12- PERIODIC CONTROLS 13- DMX PROTOCOL 29

Page 4

DELTA R

1- TECHNICAL FEATURES

Delta R Full Color

40 RGB Full Color LEDs/ LED power 3W

2.800 Lumens / 370 Lux at 5 m (medium flood lenses) RGB color generation / 16 million colours Colour temperature variable on a linear range (3.200°K÷5.500°K) No infrared emission / no ultraviolet emission LEDs average lifespan: 100.000 hours Optical units can be interchanged by users (spot / medium /wide) Interface: OLED display + 4 buttons / infrared remote control Control signals: USITT DMX 512 USITT serial digital signals 15 DMX channels Independent operation (Master / Slave) Programmable automated playback (7 days) Movement on 3 axes : Pan 320° /Tilt1 160°(Motorized) / Tilt2 135°(Manual). Safety-locking system IP65 protection level Professional HARTING / ILME sockets (IP65 protection rating) Full range AC 90-260V, 50-60Hz power supply Operating ambient temperature -10° / 40° Weight: 24 Kg

ACCESSORIES

Lenses set spot (cod. 03.LK.008) Lenses set medium flood (cod. 03.LK.001) Lenses set wide flood (cod. 03.LK.002) Flight case for 1 DELTA (cod. 0521C029) Flight case for 2 DELTA (cod. 0521C030) Safety wire (3mm x 60 cm), Ring spring catch (max. capacity load 60Kg) (Cod. 0521A010) “C” Clamp GQUICK with “Fast Lock” connection ¼ turn (max. load 80Kg) (cod. 0521A014)

Dimensions (LxDxH) projector 430 x 285 x 570 mm

Weight24 Kg (motorized version)

Packaging Dimensions (LxDxH)

530 x 500 x 660 mm

Weight 30 Kg (motorized version)

Page 5

DELTA R

Delta R Triled

20 LEDs / TRILED technology / LED power 1W x 3

2.400 Lumens / 450 Lux at 5 m (medium flood lenses) RGB color generation / 16 million colours Colour temperature variable on a linear range (3.200°K÷5.500°K) No infrared emission / no ultraviolet emission LEDs average lifespan: 100.000 hours Optical units can be interchanged by users (spot / medium flood / wide flood) Interface: OLED display + 4 buttons / infrared remote control Control signals: USITT DMX 512 USITT serial digital signals 15 DMX channels Independent operation (Master / Slave) Programmable automated playback (7 days) Movement on 3 axes : Pan 320° /Tilt1 160°(Motorized) / Tilt2 135°(Manual) Safety-locking system IP65 protection level Professional HARTING / ILME sockets (IP65 protection rating) Full range AC 90-260V, 50-60Hz power supply Operating ambient temperature -10° / 40° Weight: 24 Kg

ACCESSORIES

Lenses set spot (cod. 03.LK.004) Lenses set medium flood (cod. 03.LK.005) Lenses set wide flood (cod. 03.LK.006)

Flight case for 1 DELTA (cod. 0521C029) Flight case for 2 DELTA (cod. 0521C030) Safety wire (3mm x 60 cm), Ring spring catch (max. capacity load 60Kg) (Cod. 0521A010) “C” Clamp GQUICK with “Fast Lock” connection ¼ turn (max. load 80Kg) (cod. 0521A014)

Dimensions (LxDxH) projector 430 x 285 x 570 mm

Weight24 Kg (motorized version)

Packaging Dimensions (LxDxH)

530 x 500 x 660 mm

Weight 30 Kg (motorized version)

Page 6

DELTA R

1- TECHNICAL FEATURES

Delta 5 RGB R

108 X 1W Luxeon type LEDS (36 Red, 36 Green, 36 Blue)

2.400 Lumens / 900 Lux at 5 m (medium flood lenses) RGB color generation / 16 million colours Colour temperature variable on a linear range (3.200°K÷5.500°K) No infrared emission / no ultraviolet emission LEDs average lifespan: 100.000 hours Optical units can be interchanged by users (spot / medium /wide) Interface: OLED display + 4 buttons / infrared remote control Control signals: USITT DMX 512 USITT serial digital signals 15 DMX channels Independent operation (Master / Slave) Programmable automated playback (7 days) Movement on 3 axes : Pan 320° /Tilt1 160°(Motorized) / Tilt2 135°(Manual). Safety-locking system IP65 protection level Professional HARTING / ILME sockets (IP65 protection rating) Full range AC 90-260V, 50-60Hz power supply Operating ambient temperature -10° / 40° Weight: 24 Kg

ACCESSORIES

Dimensions (LxDxH) projector 430 x 285 x 570 mm

Weight24 Kg (motorized version)

Packaging Dimensions (LxDxH)

530 x 500 x 660 mm

Weight 30 Kg (motorized version)

Page 7

DELTA R

1- TECHNICAL FEATURES

Delta 7 RGB R

108 X 1W P4 type LEDS (36 Red, 36 Green, 36 Blue)

2.400 Lumens / 1150 Lux at 5 m (medium flood lenses) RGB color generation / 16 million colours Colour temperature variable on a linear range (3.200°K÷5.500°K) No infrared emission / no ultraviolet emission LEDs average lifespan: 100.000 hours Optical units can be interchanged by users (spot / medium /wide) Interface: OLED display + 4 buttons / infrared remote control Control signals: USITT DMX 512 USITT serial digital signals 15 DMX channels Independent operation (Master / Slave) Programmable automated playback (7 days) Movement on 3 axes : Pan 320° /Tilt1 160°(Motorized) / Tilt2 135°(Manual). Safety-locking system IP65 protection level Professional HARTING / ILME sockets (IP65 protection rating) Full range AC 90-260V, 50-60Hz power supply Operating ambient temperature -10° / 40° Weight: 24 Kg

ACCESSORIES

Dimensions (LxDxH) projector 430 x 285 x 570 mm

Weight24 Kg (motorized version)

Packaging Dimensions (LxDxH)

530 x 500 x 660 mm

Weight 30 Kg (motorized version)

Page 8

DELTA R

2- IMPORTANT SAFETY INFORMATION

2.1 Fire prevention:

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 m.

-Minimum distance from the closest illuminable surface: 1 m.

-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

2.2 Prevention of electric shock:

-High voltage is present inside the unit. Isolate the projector from the mains supply prior to performing any function which involves touching the inside of the unit.

-The level of technology inherent in the DELTA R requires the assistance of specialised personnel for all servicing.Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector. Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

2.3 Protection against direct light radiation:

-Never turn the unit on if any of the lenses or the glass lenses protection is damaged.

-Never look directly the leds when they are on.

2.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.

-Always use a second safety chain to sustain the weight of the unit in case of the failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 80°C. Never handle the unit until it’s on.

-Never install the fixture in an enclosed area lacking sufficient air flow.

-The ambient temperature should not exceed 40°C.

2.5 Level of protection against the penetration of solid and liquid matter:

-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid matter is IP 65.

Page 9

DELTA R

3- VOLTAGE AND FREQUENCY:

Delta R can operate at 90-270V, 50 or 60 Hz.

4- INSTALLATION:

Delta R may be either floor or ceiling mounted. For floor mounting installations, the unit is supplied with four rubber mounting feet on the base. For ceiling mounted installations, we reccommend the use of appropriate clamps to fix the unit to the mounting surface. The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to move or shake whilst the Delta R is moving. The Delta R is fitted with 4 fixing points on the bottom used to attach accessories (clamps, hooks, etc.) With a fast lock closure/release system (1/4 turn) to fix the fixture in any position. .

4.1 Safety cable:

We recommend the use of a safety cable or chain connected to the Delta R and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable or chain can bear the weight of the entire unit. You may attach the safety chain to the holes located on the base of the fixture, as shown in the picture below.

SAFETY CABLE FIXING POINT

4.2 Risk of fire:

Each fixture produces heat and must be installed in a well-ventilated position. The minimum recommended distance from flammable material is 1m. Minimum distance from the object being illuminated is 1 m.

Page 10

DELTA R

4.3 Ambient temperature:

The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.

5- MAINS CONNECTION:

Delta R can operate at 90-270V, 50 or 60Hz. For connection purposes, ensure that your plug can handle at least 300W power consuption.

Strict adherence to regulatory norms is strongly Recommended.

FUSE: T 3,15A

MAINS

Electronic ballast 90-260V 50 / 60Hz

5.1 Protection:

The use of a thermal magnetic circuit breaker is recommended for each Delta R. A good earth connection is essential for the correct operation of the projector.

6- DMX SIGNAL CONNECTION:

The unit operates using a digital DMX 512 (1990) signal. Connection between the control box and the projector or between projectors must be carried out using a two pair screened ø0.5 mm cable and a CANNON XLR 5 or 3 pole connector.

Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one. In this way, all the projectors are cascade connected.

CONTROLLER S T A N D A R D D M X 5 1 2

4 2

1=GND 2=DATA3=DATA+

DMX IN

DMX OUT

OUT

OUT OUT

P.S: If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

Page 11

6.1 DMX Addresses:

DELTA R have 15 DMX control channels. Here below are described the DMX channels addressing for the controller:

Projector 1 A001 Projector 2 A016 If you want to select the next projector, just add “15” Projector 3 A031 ….. A…. projector 6 A091

6.2 Selelcting the DMX address:

1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now controlled by the new DMX address.

DELTA R

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.

ENTER

DOWN

7- Movement

The projector has a maximum movement of 320° for Pan,180° for Tilt 1 and 135° for tilt 2 (7 mechanical steps 22,5° each). DO NOT place any obstructions in the path of the projector's movement.

Tilt 2 mechanical regulation

PAN 320°

TILT1 180° Motorized

TILT2 135° Mechanical

Page 12

DELTA R

8- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The DELTA R display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections.

DELTA SOFTWARE RELEASE 1.72

1)GLOBAL SETTING MENU

LANGUAGE DEFAULT PAGE SECURITY DEFAULT SETTING SET DATE SET TIME UPDATE DOWNLOAD ABOUT

2)MODE SETTING MENU

MODE DMX MODE RECORDER MODE MASTER MODE SLAVE MODE IR MODE MANUAL MODE TWILIGHT

3)MOVING HEAD SETUP MENU

PAN MIN PAN MAX TILT MIN TILT MAX CALIBRATE PAN CALIBRATE TILT INVERT PAN INVERT TILT SWAP PAN & TILT ENCODER RESET PAN & TILT SPEED PAN & TILT

4)LED SETUP MENU

COLOUR MODE WHITE BALANCE BOOST DRIVING MIN RGB MAX RGB SMOOT FILTER PWM FREQUENCY

5)DIPLAY SETTINGS MENU

CONTRAST FLIP DISPLAY SCREEN SAVER

6)MEASURE MENU

LIFE DMX VOLTAGE TEMPERATURA TWILIGHT

Page 13

1)GLOBAL SETTING MENU

LANGUAGE DEFAULT PAGE SECURITY DEFAULT SETTING SET DATE SET TIME UPDATE DOWNLOAD ABOUT

DELTA R

A001

Up-Down

LANGUAGE SELECTION This menu allow to set the

Up-Down

DEFAULT PAGE SELECTION This menu allow to set the visualisation for the start up page

Up-Down

SECURITY PASSWORD This menu allow to select a security password to lock the user’s settings

Language

Default Page

Security

Up-Down

GLOBAL SETTING

Up-DownENTER

Up-Down

Up-DownENTER

Up-Down

Up-DownENTER

Up-Down

Set Language English

Set Default Page

Four Digit

A001

Status

Security Unlocked

Enter Security Code 0 0 0 0

ENTER

English = Default

Four Digit = DMX address visualisation

Status = DMX / Color Mode / Boost Power / Security

Default 0000 = no password

Universal Unlock code = 2903

ENTER

Up-Down

DEFAULT SETTINGS This menu allow to set the unit to the company settings

Up-Down

DATE SETTING This menu allow to set the day of the week the month and the year

Default Setting

Set Date

Up-DownENTER

Up-Down

Up-DownENTER

Confirm Security Code 0 0 0 0

Restore Main Settings

ENTER to CONFIRM & Reboot

Set Date

Year 2007 Month Jan Day of the month 01 Day of the week Mon

GAME,TIMER and WHITE SETTING will not be changed

Date settings for Stand Alone mode

ENTER

Page 14

DELTA R

Up-Down

TIME SETTING This menu allow to set the unit’s on board clock for STAND ALONE MODE

Up-Down

UPDATE MENU This menu allow to upgrade the uni’s software by computer or remote control

Up-Down

DOWNLOAD MENU This menu allow to save unit’s programs into computer

Set Time

Update

Download

Up-DownENTER

Set Time

Real time internal clock setting

ENTER

Hour 03

Minute 01

Up-DownENTER

Select UPDATE Mode Direct to PC

Update the unit’s software from PC by cable

ENTER

ENTER to CONFIRM

Up-DownENTER

Select DOWNLOAD Mode Direct to PC

Download the unit’s program to PC by cable

ENTER

ENTER to CONFIRM

Up-Down

ABOUT MENU This menu show informations about unit’s hardware and software

ABOUT

ENTER

Up-Down

About DELTA R Master PCB 0514L019 Loader Version 1.02 HW Version 1.01 SW Version 1.61 Pan&Tilt PCB 0514S100 PAn&Tilt Version 2.05

Unit’s Hardware and software infos

ENTER

Page 15

2)MODE SETTING MENU

MODE DMX MODE RECORDER MODE MASTER MODE SLAVE MODE IR MODE MANUAL MODE TWILIGHT

DELTA R

A001

Up-Down

DMX ADDRESS SELECTION This menu allow to set the unit’s DMX address.

Up-Down

RECORDER MODE SETTING This menu let you create 2 different chases,CPR1 and CPR2 (16 steps each) that will then run in Master Mode. Two different recording mode are available:

1)Manual Recording Mode

2)DMX Recording Mode

1)Manual Recording Mode

Mode DMX

Mode Recorder

Up-Down

MODE SETTINGS

Up-DownENTER

Set Address DMX

001

RECORDER Mode

Input Mode MANUAL

Select Chase CPR1

RECORDER MANUAL CPR1 STEP 01 EDIT PAN 016 TILT 255 SHUTTER 009 DIMM 017 R 016 G 016 B 000 WHITE 012 CTC 000 MACRO 000

ENTER

Address range 001-489

In Manual Recording Mode,it is possible to create and store the steps of the chase by using the unit display panel and buttons.

Three different options are available:

1)EDIT = Let you modify and store new values for all the channels on the selected Step.

2)WIEV MEM = Let you see the existing programmed steps of the chase

3)SET LAST = Let you set the last step to be ran on the chase.

ENTER

2)DMX Recorder Mode To program CPR1 and CPR2 by using a DMX controller, 3 more DMX channels are needed in addition to the 15 channels necessary to control the unit. So that in RECORDER mode (via DMX) the unit will need 18 channels to be correctly programmed. The 3 new DMX channels are: DMX channel 16 = STEPS channel From 0 - 15 = VIEW DMX, the unit shows the values received from the DMX controller in that moment. From 16 – 255, the previously programmed steps (16 steps from 01 to 16) are displayed. DMX channel 17 = VIEW / EDIT / SET LAST channel If channel 16 (STEPS channel) is set to value 0 - 15, the DMX channel 17 has no functions. If channel 16 (STEPS channel) is set to value 16 - 255, the DMX channel 17 has the following functions: From 0 - 19 = VIEW MEM, the unit shows the previously programmed steps. From 20 - 234 = EDIT, the unit runs the configuration given by the DMX controller in that moment.

With the STEPS channel it is possible to select the step to create, while with REC channel it is possible to store the configuration on the selected step.From 234 - 255 = SET LAST, the unit runs the configuration given by the DMX controller in that moment closing the Program as last step. With the REC channel it is possible to record the selected step as last step to be ran on the Program. DMX channel 18 = REC channel REC channel saves the configuration given by the DMX controller in the selected step: you change the DMX value from 0 to 255 (the display shows “WRITING” indicating that the step has been recorded). We suggest to keep the REC channel set to 0 and to run through the 255 only once you have decided to save the new configuration. If CPR1 or CPR2 are not closed, by indicating the last step (Edit channel between 235-255), all 16 steps will be played through in playback mode, even if not programmed.

RECORDER Mode

Input Mode DMX

Select Chase CPR1

Warning 18 channels !

RECORDER DMX CPR1 STEP 01 EDIT PAN 016 TILT 255 SHUTTER 009 DIMM 017 R 016 G 016 B 000 WHITE 012 CTC 000 MACRO 000

In DMX Recording Mode,it is possible to create and store the steps of the chases by using an external DMX controller.

WARNING !

To program CPR1 and CPR2 by using a DMX controller, 3 more DMX channels are needed in addition to the 15 channels necessary to control the unit.

ENTER

Page 16

DELTA R

Up-Down

MASTER MODE SETTING This menu allow to set Delta R as master unit (No DMX signal must be present on unit’s DMX input panel) . The unit will ran in automatic mode without needing of an external controller. Different chases are selectable by user

CPR1/CPR2/CPR1&2 Chases with 16 steps previously created in RECORDER mode. Time and Wait time selectable by user

CRNB Rainbow colours effect. Time and Pan&Tilt selectable by user

CUE 1-9 Color Macros with fixed colors Pan&Tilt selectable by user

Mode Master

Up-DownENTER

Up-Down

Set MASTER MODE

Mode : MASTER Actual : DMX

ENTER to CONFIRM

Master Mode

Set CHASE CPR1 Set TIME Sec 0025 Set WAIT Sec 0015

The Delta setted as MASTER, send DMX signal to all the other units connected to the same DMX line

By setting all the units connected to the MASTER, to DMX address 1, them will be sinchronized with the Master unit following the chase selected on it, including TIME, WAIT and Pan&Tilt position of the MASTER unit.

By setting all the units connected to the MASTER, as SLAVE unit (see SLAVE mode), them will be sinchronized with the Master unit only for TIME and WAIT time, but running their own chase CPR1/CPR2 with dedidicated Pan&Tilt position, colors and effects.

ENTER

Up-Down

SLAVE MODE SETTING This menu allow to set the Delta R as slave unit. DMX signal must be present from MASTER unit in order to ran in SLAVE mode.

Mode Slave

Up-DownENTER

Set SLAVE MODE

The SLAVE unit receive DMX signal

ENTER

from the MASTER unit

Mode : SLAVE Actual : DMX

By setting all the units connected to the MASTER, as SLAVE unit, them

ENTER to CONFIRM

will be sinchronized with the Master unit only for TIME and WAIT time, but running their own chase CPR1/CPR2 with dedidicated Pan&Tilt position, colors and effects.

Page 17

DELTA R

Up-Down

IR MODE SETTING By activating IR mode on Delta unit it will be possible to navigate trought the unit functions by using the D.T.S. infrared remote control (D.T.S. Code :0514L008).

Mode IR

Up-DownENTER

Set IR MODE

Mode : IR Actual : DMX

ENTER to CONFIRM

INFRARED REMOTE CONTROL

By activating IR mode on Delta unit it will be possible to navigate trought the unit functions by using the D.T.S. infrared remote control (D.T.S. Code :0514L008).

Infrared remote control functions:

ON/OFF and MUTE buttons

In Master/Slave mode let you stop the games running. Master and slave units will go in Stand-by mode

1-9 buttons

Let you select the chase to run (CPR1/CPR2/CRNB/CUE 1-6)

1-/.. Button

Let you select the chase to run (CUE 7-9)

VOL +/-

No function

PROG +/-

Let you scroll between the selectable chases

RED/GREEN/YELLOW/BLUE buttons

Direct acces to cues for Red/Green/Blue/Yellow colour. Red=CUE1 / Green=CUE3 / Yellow=CUE2 / Blue=CUE5

Navigation buttons

Same as UP/DOWN on unit display

OK button

Same as ENTER on unit display

MENU button

Same as MENU on unit display

The unit is controlled by the infrared remote control

ON/OFF Button

1-/.. Button

VOL +/Buttons

NAVIGATION Buttons

OK Button

ENTER

1-9 Buttons

PROG +/Buttons

R-G-Y-B Buttons

MENU Button

Up-Down

MANUAL MODE SETTING This menu let you control Delta unit in manual mode by using the unit display. In MANUAL mode, no external controller is needed.

Mode Manual

Up-DownENTER

Set MANUAL MODE

In MANUAL mode it is possible to

ENTER

adjust all the unit functions by using

Mode : MANUAL Actual : DMX

ENTER to CONFIRM

MAN Mode Enter VALUES

Channel Value PAN H 128

UP/DOWN and ENTER buttons:

PAN H PAN L TILT H TILT L SPEED PAN&TILT SHUTTER DIMMER RED GREEN BLUE WHITE CTC MACRO FUNCTION RESET

Page 18

DELTA R

Up-Down

TWILIGHT MODE MENU This menu allow to set the unit in Twilight mode. Twilight mode let you turn ON and OFF the unit at a specific clock time (including day of the week) and/or at a specific twilight level. The Twilight mode make use of a twilight sensor located on the front panel near unit display.

To know the twilight ambient level value measured from the sensor, scroll the unit menu till MEASURE Mode and select Twilight.

TWILIGHT MODE

Up-DownENTER

Set TWILIGHT MODE

Mode : TWILIGHT Actual : DMX

The unit is switched on and off at the desired twilight level or/and at a specific clock time.

ACTION :

ENTER to CONFIRM

Let you select the desired function in twilight mode.

TWILIGHT Mode ACTION CPR1 LEVEL ON 100 OFF 150: TIME CONDIT INCLUSIVE DAY Mon START 22:00 TIME ON 10:00

You can choose between: DMX / CPR1 / CPR2 / CPR1&2 / CRNB / CUE 1-9 /

LEVEL ON and OFF : Let you select the desired twilight levels for: Twilight mode ON and OFF.

TIME CONDITION: Four different options are available:

1) INACTIVE Clock time (START) and Time on period (TIME ON), are inactive. In this condition the unit goes ON only if the twilight level is valid

2)COMBINED Clock time (START), Time on period (TIME ON) and Twilight level are active. In this condition, the unit goes ON only if all the parameters are valid.

3)INCLUSIVE Clock time (START), Time on period (TIME ON) and Twilight level are active. In this condition, the unit goes ON also if only one of the paramete is valid.

4)EXCLUSIVE Clock time (START) and Time on period (TIME ON), are active, while Twilight level is inactive. In this condition, the unit goes ON only if Clock time (START) is valid.

ENTER

3)MOVING HEAD SETUP MENU

PAN MIN PAN MAX TILT MIN TILT MAX CALIBRATE PAN CALIBRATE TILT INVERT PAN INVERT TILT SWAP PAN & TILT ENCODER RESET PAN & TILT SPEED PAN & TILT

A001

Up-Down

MOVING HEAD SETUP

ENTER

Page 19

DELTA R

A001

Up-Down

PAN MINIMUM POSITION This menu allow to set the Pan minimum position (Default =000)

Up-Down

PAN MAXIMUM POSITION This menu allow to set Pan maximum position (Default = 255)

Up-Down

TILT MINIMUM POSITION This menu allow to set the Tilt minimum position in degrees (Default =000)

Pan Min

Pan Max

Tilt Min

Up-Down

MOVING HEAD SETUP

Up-DownENTER

Setting Pan Min

Pan Min : 000

Setting Pan Max

Pan Man : 000

Setting Tilt Min

Tilt Min : 000

ENTER

Range 000-255 Default = 000

Range 255-000 Default = 255

Range 000-255 Default = 000

ENTER

Up-Down

TILT MAXIMUM POSITION This menu allow to set the Tilt maximum position (Default = 255)

Up-Down

PAN CALIBRATION This menu allow to calibrate Pan home position (Default = 105)

Up-Down

TILT CALIBRATION This menu allow to calibrate Tilt home position (Default = 128)

Tilt Max

Calibrate Pan

Calibrate Tilt

Up-DownENTER

Setting Tilt Max

Range 255-000

ENTER

Default = 255

Tilt Max : 000

Up-DownENTER

Calibrating Pan

Pan : 105

Up-DownENTER

Calibrating Tilt

Tilt : 105

Range 000-255

ENTER

Page 20

DELTA R

Up-Down

PAN INVERTION This menu allow to set the Pan movement. Normal or Inverted

Up-Down

TILT INVERTION This menu allow to set the Tilt movement. Normal or Inverted

Up-Down

PAN&TILT SWAP This menu allow to invert the control of Pan with the control of Tilt.

Invert Pan

Invert Tilt

Swap Pan&Tilt

Up-DownENTER

Set PAN INVERTION

Pan movement Normal or Inverted Default = Normal

ENTER

Pan : Normal

Actual Normal

Up-DownENTER

Set TILT INVERTION

Tilt movement Normal or Inverted

ENTER

Default = Normal

Tilt : Normal

Actual Normal

Up-DownENTER

Set Pan/Tilt SWAPPING

Pan control inverted with Tilt control

ENTER

and vice versa

Swap : Normal

Actual Normal

Dfault = Normal

IMPORTANT: (During PAN/TILT MIN,PAN/TILT MAX and PAN/TILT CALIBRATE setting,PAN/TILT INVERT and PAN/TILT SWAP are disabled

Up-Down

ENCODER SETTING This menu allow to enable/disable the auto-repositioning function for Pan and Tilt

Up-Down

PAN&TILT RESET This menu allow to reset Pan and Tilt Motors

Encoder

Reset Pan & Tilt

ENTER

Up-DownENTER

Set Encoder Status

Encoder : Active

Actual Active

Resetting Pan & Tilt

PRESS ENTER To RESET Pan & Tilt

Pan/Tilt auto-repositioning system enabled or disabled Default = Active

Pan &Tilt motors reset

Up-Down

PAN & TILT MAXIMUM SPEED This menu allow to set the maximum speed for Pan & Tilt movement.

Speed Pan & Tilt

Up-DownENTER

Set SPEED MAX P&T

Speed MAX % 100

Pan&Tilt maximum motor speed Selectable between 25-100%

ENTER

Page 21

4)LED SETUP MENU

COLOUR MODE WHITE BALANCE BOOST DRIVING MIN RGB MAX RGB SMOOT FILTER PWM FREQUENCY

DELTA R

A001

Up-Down

COLOUR MODE This menu allow to select the LED’S colour mode control system between RGB, CMYK or HSV

Up-Down

WHITE BALANCE This menu allow to select the levels for Red,Green and blue obtaining a custom White

Colour Mode

White balance

Up-Down

LED SETUP

Up-DownENTER

Set Colour Mode RGB CMYK HSV

Actual RGB

Setting WHITE RED 255 GREEN 255 BLUE

255

ENTER

RGB Mode (Default) Ch7 = Dimmer / Ch8 = Red Ch9= Green / Ch10= BLue

CMYK Mode Ch7 = Black / Ch8 = Cyan Ch9= Magenta / Ch10= Yellow

HSV Mode Ch7 = Nu / Ch8 = Hue Ch9= Saturation / Ch10= Value

The Custom White can be Recall by setting DMX channel 11 (WHITE) in the range 172-213

ENTER

Up-Down

BOOST DRIVING This menu allow to increase the LED’s current from 350mA to 500 mA

Up-Down

RGB MINIMUM VALUES This menu allow to select the minimum levels for Red,Green and blue

Up-Down

RGB MAXIMUM VALUES This menu allow to select the maximum levels for Red,Green and blue

Boost Driving

Min RGB

Max RGB

Up-DownENTER

Setting LED BOOST BOOST Status

Whit BOOST active,the LED’s current is setted to 500mA (30%more gain).

ENTER

Default = Disable

Active

NTC thermal protection active.

Warning TEMPERATURE

PROTECTION ACTIVATED

Up-DownENTER

Setting RGB Min

These settings have priority on Master Dimmer (DMX channel 7)

ENTER

Min RED : 000 Min GREEN : 000 Min BLUE

Up-DownENTER

Setting RGB Max

: 000

These settings have priority on Master Dimmer (DMX channel 7)

ENTER

Max RED : 000 Max GREEN: 000 Max BLUE

: 000

Page 22

DELTA R

Up-Down

SMOOTH FILTER VALUE This menu allow to select the value of the delay( in millisecons) for RGB channels reaction to DMX or Program variation. 001=2.5 ms delay (Fast response) 100=250 ms delay (Slow response)

Up-Down

PWM FREQUENCY VALUE This menu allow to adjust the PWM frequency value (Hz) in order to reduce flickering in the process of your camera recordings

Smooth Filter

PWM frequency

5)DIPLAY SETUP MENU

CONTRAST FLIP DISPLAY SCREEN SAVER

Up-DownENTER

Set Smooth Filter

Filter Value: 010

Range = 001 / 100 Default = 10 001 = 2.5mS (Istant response to DMX

ENTER

variation) 100 = 250mS (Smooth response to

ENTER to CONFIRM

DMX variation)

Up-DownENTER

Set PWM Frequency

427 Hz 1000 Hz 2000 Hz 4000 Hz 6000 Hz Actual 427 Hz

5 different PWM frequencies available. Default = 427 Hz

ENTER

A001

Up-Down

DISPLAY CONTRAST This menu allow to select display’s contrast level.

Up-Down

DISPLAY FLIP This menu allow to reverse display's reading depending on the mounting position (On the ground or suspended).

Up-Down

SCREEN SAVER This menu allow to activate the screen saver.

Contrast

Flip Display

Screen saver

Up-Down

DISPLAY SETUP MENU

Up-DownENTER

Contrast 7

0 1 2 3 4 5 6 7 8 9

Flip Select

Up-DownENTER

SCREEN SAVER SETTING

Screen Type None

Screen Time (sec):005

ENTER

Range = 0-9

Default = On the ground

Screen saver selectable between None (default) and Blank. Screen saver activating time selectable between 005 / 180 seconds

ENTER

Page 23

6)MEASURE MENU

LIFE DMX VOLTAGE TEMPERATURE TWILIGHT

DELTA R

A001

Up-Down

LIFE TIME This menu show the total UNIT LIFE TIME (reset not possible) and the RGB life

TIME (reset possible)

Life

Up-Down

MEASURE MENU

Up-DownENTER

Measure Life

Delta R Total LIFE

Days Hours Min Sec

1 19 47 55

UP/DW Change Measure

Measure Life

Delta R RED LIFE

Days Hours Min Sec

0 5 22 30

UP/DW Change Measure

Measure Life

Delta R GREEN LIFE

ENTER

Total Unit Life Time Reset not possible

To resed Red life time,keep pushed Enter button for more than 5 seconds

To resed Green life time,keep pushed Enter button for more than 5 seconds

ENTER

Days Hours Min Sec

0 4 37 15

UP/DW Change Measure

Measure Life

Delta R BLUE LIFE

Days Hours Min Sec

0 4 06 53

UP/DW Change Measure

To resed Blue life time,keep pushed Enter button for more than 5 seconds

ENTER

Page 24

DELTA R

Up-Down

DMX This menu show the DMX channel levels

Up-Down

VOLTAGE This menu show the different Voltage levels for every electronic circuit inside the unit

Up-Down

TEMPERATURE This menu show the NTC sensor temperature.

Dmx

Voltage

Temperature

Up-DownENTER

Measure DMX Start Channels Values

DMX channel levels as received from DMX line

ENTER

001 000 000 000 000 005 000 000 000 000 009 000 000 000 000 013 000 000 000 000

Up-DownENTER

Measure VOLTAGE

All the values are espressed in Volt

ENTER

V Motor 36,9 V Power 160,5 V Internal 17,6 V Oled 13,2

Up-DownENTER

LED’s temperature monitor

ENTER

Measure TEMPERATURE

Celsius 20,5

Up-Down

TWILIGHT This menu show the twilight level.

Twilight

Up-DownENTER

Measure TWILIGHT

Light sensor Twilight level (Located on the front panel of the

ENTER

unit)

Value : 0314

Page 25

DELTA R

9- OPENING UP THE PROJECTOR HOUSING:

It is possible to inspect the inside of the projector by removing the covers as shown below.

Attention: REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR'S INTERNAL COMPONENTS.

Proceed as per the pictures below

9.1- Arms

9.2- Base

Remove these two screws on both arm sides

Remove the 12 screws located on the base

Page 26

10- CHANGHING THE LENSES

Delta R Full Color

Optical Lenses set can be interchanged by users. Three different models are available: (spot / medium /wide) Lenses set spot (cod. 03.LK.008) Lenses set medium (cod. 03.LK.001) Lenses set wide (cod. 03.LK.002)

To change the lenses set, proceed as per the pictures below

DELTA R

Remove these 12 screws on both sides of the rear head assembly

Remove the top head cover

Remove these 8 screws and change the panel

ATTENTION: Never touch LEDs and Lensens with hands

Page 27

10- CHANGHING THE LENSES

Delta R Triled

To change the lenses set, proceed as per the pictures below

DELTA R

Remove these 12 screws on both sides of the rear head assembly

Remove the top head cover

Remove these 6 screws and change the panel

ATTENTION: Never touch LEDs and Lensens with hands

Page 28

DELTA R

11- PERIODIC CLEANING:

Front lenses Glass

The dust can reduce the luminous output substantially. Regularly clean the front lenses glass using a soft cotton cloth, dampened with a specialist glasses cleaning solution.

12- PERIODIC CONTROLS:

Mechanical parts:

Periodically check all mechanical parts and the gaskets, replacing them if necessary.

Electrical components:

Check all electrical components for correct earthing and proper attachment of all connectors, refastening if necessary.

Fuse replacement:

Locate the fuse, which protect the electronics, in the base of the DELTA R. Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.

Attention: Disconnect mains power prior to removing the projector housing.

Page 29

13- DMX PROTOCOL

15 CHANNELS MODE

1 PAN msb 320°

2 PAN lsb 3 TILT msb 180° 4 TILT lsb 5 SPEED MOVEMENT 6 SHUTTER 7 DIMMER 8 RED 9 GREEN 10 BLUE 11 WHITE (Preprogrammed white at different color temperature) 12 CTC 13 COLOURS MACRO 14 FUNCTIONS 15 RESET

DMX CHANNEL

Parameter: PAN msb

Parameter: PAN lsb

Parameter: TILT msb

Parameter: TILT lsb

Parameter: MOVEMENT SPEED

DELTA R

DMX range

Value

0-10

11-255

DMX CHANNEL

DMX range

Value

0-9 10-19 20-29 30-119

120-149 150-179 180-204 205-229 230-244 245-255

(degrees)

Move

range

Mode Option Function

Standard

Vector mode from fast to slow

Mid point

DMX value

Mid point

DMX value

Parameter: SHUTTER

Move

range

(degrees)

5 14 24

192 218

238

250

Mode Option Function

Black-out

Open

Black-out

Strobe at variable speed(from slow to fast)

Pulse open at variable speed(from slow to fast) Pulse close at variable speed(from slow to fast)

Random Strobe (Master and RGB active)

Random Strobe (Full)

PAn&Tilt movement in Black-out

Open

Page 30

DMX CHANNEL

DMX range

Value

0-255

Mid point

DMX value

Parameter: DIMMER NOTE: IN CMYK MODE Ch7 = BLACK

Move

range

Mode Option Function

DELTA R

(degrees)

Proportional dimmer

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

DMX CHANNEL

DMX range

Value

0-255 Proportional colour

Mid point

DMX value

Mid point

DMX value

Mid point

DMX value

Parameter: RED NOTE: IN CMYK MODE Ch8 = CYAN

IN HSV MODE Ch8 = HUE

Move

range

Mode Option Function

(degrees)

Parameter: GREEN NOTE: IN CMYK MODE Ch9 = MAGENTA

IN HSV MODE Ch9 = SATURATION

Move

range

Mode Option Function

(degrees)

Parameter: BLUE NOTE: IN CMYK MODE Ch10 = YELLOW

IN HSV MODE Ch10 = VALUE

Move

range

Mode Option Function

(degrees)

DMX CHANNEL

DMX range Mid point

Value DMX value

0-43 21 44-85 86-127

Parameter: WHITE (Pre-programmed White at diff. color temperature)

66 105

Move

range

(degrees)

Mode Option Function

No Function

Full (Red-Green-Blue at Full)

White DTS

IF CHANNEL 14 (FUNCTIONS) = CUSTOM WHITE RECALL (Dmx range value 0 - 79)

128-171 172-213

214-255

150

192

234

White Balance(White Balance programmed on Unit’s Menu)

Custom White Recall

White CTC (Channel 12 CTC enabled Linear color temp. Correction: 3000K-7000K)

IF CHANNEL 14 (FUNCTIONS) = CUSTOM WHITE CREATE (Dmx range value 80 - 160)

128-171 172-213

214-255

150

192

234

Custom White Create (RGB levels selectable by DMX)

White Balance(White Balance programmed on Unit’s Menu)

White CTC (Channel 12 CTC enabled Linear color temp. Correction: 3000K-7000K)

Page 31

DMX CHANNEL

DMX range Mid point

Value DMX value

Parameter: CTC (Color temperature correction)

Move

range

(degrees)

Mode Option Function

IF CHANNEL 11 (White) = WHITE CTC (Dmx range value 214 - 255)

0-255

Linear color temp. Correction: 0 = 3000K / 128 = 5500K / 255 = 7000K

IF CHANNEL 11 (White) = NO FUNCTION (Dmx range value 0 - 43)

0-255

DMX CHANNEL

DMX range

Value

Parameter: COLOUR MACROS

Mid point

DMX value

Smooth RGB linear Hue correction

Move

range

(degrees)

Mode Option Function

0-14 15-29 30-44 45-59 60-74 75-89 90-104

105-119

120-134

135-149 150-164 165-179

180-194

195-209

210-225 226-239 240-255

DELTA R

No Function Macro 1 Macro 2 Macro 3

Macro

Macro 4 Macro

Macro 5 Macro

Macro 6 Macro

Macro 7 Macro

Macro 8 Macro

Macro 9

Macro

Macro 10 Macro

Macro 11 Macro

Macro 12

Macro

Macro 13 Macro

Macro 14 Macro

Macro 15 Macro 16

DMX CHANNEL

DMX range

Value

0-79

80-160

161-255

DMX CHANNEL

DMX range

Value

0-15

16-255

Mid point

DMX value

Mid point

DMX value

Parameter: FUNCTIONS (Recall,Create and Store the Custom white)

Move

range

(degrees)

Custom White Recall (Enable CH 11 for Custom white Recall)

Mode Option Function

Custom White Create (Enable CH 11 for Custom white Creation)

Parameter: RESET (Pan&Tilt Reset)

Move

range

(degrees)

120

Custom White Store (Store the Custom White created )

Mode Option Function

No Functions

Pan&Tilt Reset

Page 32

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.

MADE IN ITALY

*0517I069*

D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy

Tel. +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it www.dts-lighting.it