DTM System GALACTIC NANO 868 Installation Manual
NANO 868
ONE CHANNEL RADIO RECEIVER
I C
C T
A
L
A
G
insta l l a t i o n m a n u a l v. 1.5
GENERAL INFORMATION
NANO receiver is DTM remote control system additional device. It is a simplified one channel receiver designed to
work with gates, roller shutter and other devices where remote control impulse is required.
NANO receiver is a simple and inexpensive device to expand functionality of simpler installation with remote
control.
GALACTIC function allows to add remotes programmed and configured outside of the installation, without need
to use receiver button.
TECHNICAL SPECIFICATIONS
4clear and simple user interface based on single button with built-in LED;
4easy remote registering and GALACTIC function allows to add remotes without need to use receiver button;
4verifying number of registered remotes;
4complimentary 104-bit IRS variable rolling code ;
4 power supply 12...24V AC/DC ±10%;
4 max current consumption 60mA (relay on);
4memory up to 200 remotes DTM868MHz series;
4one separate NO relay output, permissible resistive load 1A/24V AC/DC;
4 monostable mode backup time 1s;
4superheterodyne receiver, frequency: 868 MHz;
4 work temperature -20°C to +55°C;
4 IP-20 protection, designed to be installed in gate drivers or indoors;
4dimensions / with
mounting brackets
[mm]: 48 x 42 x 22 / 64
programming button with LED
x 42 x 22.
( )
Antenna
( )
12...24V AC/DC
C1 (NO)
Fig.1. NANO868 receiver electric connection description
1. Installation
Receiver designed for use inside buildings or inside other automation equipment. Ensure proper working
conditions in line with technical parameters. Do not mount in locations exposed to high humidity and frequent
sudden changes of temperature.
Due to externally accesible screw connection provide galvanic isolation from other devices and wires.
Attention to thermal insulation of automation elements which can reach high temperatures (motors,
transformers, circuits implementing, heat sink etc.). For electrical connection see Fig. 1.
Factory wire antenna connected to antenna terminal. Optionally external antenna can be used. Connect external
antenna with 50Ω impedance coaxial cable to ( ) terminal - center core, to ( ) terminal- shield.
2. Receiver programming
2.1. Registering remote to receiver's memory
While holding receiver button press remote button.
LED blink. Selected button will control the output
channel of receiver. Any remote button can be
registered.
Registering another button does not erase
4
previously registered button.
Holding receiver button for more than 15
4
seconds will erase memory.
Attempt of registering 201 transmitter will
4
fail. LED will not blink.
11
PRESS AND HOLD
C1 BUTTON
Fig. 2. Remote button programming.
C1 LED
BLINK
2
BLINK
PRESS REMOTE
3
BUTTON
4
CZAS
3x
C1 LED
BLINK
THREE TIMES
2.2. Easy remote registering
Easy remote registering function allows registering
new remotes without access to receiver button.
Previously registered remote is needed.
press and hold for 15 seconds previously
4
REMOTES IN RECEIVER RADIO RANGE
registered remote button in receiver radio
2
range,
in no more than 3 seconds press and hold new
4
remote button for 15 seconds, new remote is
registered with the same active button as in the
previously registered remote.
11
PRESS AND HOLD
FOR 15 SECONDS
ANY BUTTON
OF„OLD” REMOTE
Fig.3. Easy remote registering.
BREAK TIME
MAX 3 SECONDS
PRESS AND HOLD
FOR 15 SECONDS
ANY BUTTON
OF „NEW” REMOTE
CZAS
Failure in registering may be caused by:
low battery of the remote,
4
radio interference during the procedure,
4
full memory of the receiver.
4
2.3. Easy remote registering function LOCK / UNLOCK
To protect receiver against unauthorized attempts of registering remote (important in access protected user
zones) easy remote registering function must be locked. To lock/unlock easy remote registering function:
turn off receiver power supply;
4
press and hold C1 button;
4
turn on receiver power supply;
4
While holding the button, C1 LED will alternately light on and light off every 5 seconds. To lock/unlock
4
easy remote registering release button when:
LED light on - easy remote registering locked,
LED light off - easy remote registering unlocked.
Loading...