DSE DSE103 MKII Operator's Manual
DSE103 MKII Operator Manual Issue 1
DEEP SEA ELECTRONICS PLC
DSE103 MK II Speed Switch Operators
Manual
Document number 057-135
Author : Paul Gibbons
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
parts@genpowerusa.com
SHOP ONLINE
www.genpowerusa.com
DSE103 MKII Operating Manual
2
Deep Sea Electronics Plc
Highfield House
Hunmanby
North Yorkshire
YO14 0PH
ENGLAND
Sales Tel: +44 (0) 1723 890099
Sales Fax: +44 (0) 1723 893303
E-mail: sales@deepseaplc.com
Website: www.deepseaplc.com
DSE Model 103 MKII Speed Switch Operators Manual.
© Deep Sea Electronics Plc
All rights reserved. No part of this publication may be reproduced in any material form (including photocopying or storing in any
medium by electronic means or other) without the written permission of the copyright holder except in accordance with the
provisions of the Copyright, Designs and Patents Act 1988.
Applications for the copyright holder’s written permission to reproduce any part of this publication should be addressed to Deep
Sea Electronics Plc at the address above.
The DSE logo is a UK registered trademark of Deep Sea Electronics PLC.
Any reference to trademarked product names used within this publication is owned by their respective companies.
Deep Sea Electronics Plc reserves the right to change the contents of this document without prior notice.
Amendments since last publication
Issue no. Comments
1 First Release
Clarification of notation used within this publication.
NOTE:
Highlights an essential element of a procedure to ensure correctness.
CAUTION!
Indicates a procedure or practice, which, if not strictly observed, could result in damage or
destruction of equipment.
WARNING!
Indicates a procedure or practice, which could result in injury to personnel or loss of life if not
followed correctly.
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
parts@genpowerusa.com
SHOP ONLINE
www.genpowerusa.com
DSE103 MKII Operating Manual
3
TABLE OF CONTENTS
Section Page
1 BIBLIOGRAPHY .............................................................................................. 4
1.1 INSTALLATION INSTRUCTIONS ....................................................................................... 4
1.2 MANUALS ............................................................................................................................ 4
1.3 CONFIGURATION SOFTWARE ......................................................................................... 4
2 INTRODUCTION .............................................................................................. 5
3 SPECIFICATIONS ............................................................................................ 6
3.1 PART NUMBERING ............................................................................................................ 6
3.2 TERMINAL SPECIFICATION .............................................................................................. 6
3.3 POWER SUPPLY REQUIREMENTS .................................................................................. 6
3.4 INPUTS ................................................................................................................................ 7
3.4.1.1 FREQUENCY SENSING INPUT HZ , RPM ............................................................................................ 7
3.4.1.2 MAGNETIC PICKUP .............................................................................................................................. 7
3.5 OUTPUTS ............................................................................................................................ 8
3.5.1.1 TACHOMETER ...................................................................................................................................... 8
3.5.1.2 CONFIGURABLE OUTPUTS R1, R2 ..................................................................................................... 8
3.6 COMMUNICATION .............................................................................................................. 8
3.6.1.1 USB P813 INTERFACE CONNECTION ................................................................................................. 8
3.7 DIMENSIONS AND MOUNTING ....................................................................................... 10
3.7.1.1 DIMENSIONS ....................................................................................................................................... 10
3.7.1.2 MOUNTING .......................................................................................................................................... 10
4 INSTALLATION .............................................................................................. 11
4.1 TERMINAL NUMBER AND DESCRIPTION...................................................................... 11
4.2 TYPICAL WIRING DIAGRAM............................................................................................ 12
5 SETTINGS AND ADJUSTMENT .................................................................... 13
5.1 SETTING OF NOMINAL SPEED ....................................................................................... 13
5.2 ADJUSTMENT OF TRIP POINTS ..................................................................................... 13
5.3 METER CALIBRATION ..................................................................................................... 13
5.4 PC CONFIGURATION ....................................................................................................... 13
6 APPLICABLE STANDARDS .......................................................................... 14
7 COMMISSIONING .......................................................................................... 14
7.1 PRE-COMMISSIONING ..................................................................................................... 14
8 FAULT FINDING ............................................................................................ 15
9 MAINTENANCE, SPARES, REPAIR AND SERVICING ................................ 15
10 WARRANTY ................................................................................................ 15
11 DISPOSAL................................................................................................... 15
11.1 WEEE (WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT) ............................. 15
11.2 ROHS (RESTRICTION OF HAZARDOUS SUBSTANCES) .......................................... 15
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
parts@genpowerusa.com
SHOP ONLINE
www.genpowerusa.com
DSE103 MKII Operating Manual
4
1 BIBLIOGRAPHY
This document refers to and is referred to by the following DSE publications which can be obtained from the DSE
website www.deepseaplc.com
1.1 INSTALLATION INSTRUCTIONS
Installation instructions are supplied with the product in the box and are intended as a ‘quick start’ guide only.
DSE PART DESCRIPTION
053-124 DSE103 MKII Installation Instructions
1.2 MANUALS
DSE PART DESCRIPTION
057-136 DSE103 MKII Speed Switch Software (using DSE configuration Suite Lite)
1.3 CONFIGURATION SOFTWARE
DESCRIPTION
DSE Configuration Suite Lite
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
parts@genpowerusa.com
SHOP ONLINE
www.genpowerusa.com
DSE103 MKII Operating Manual
5
2 INTRODUCTION
This document details the installation and operation requirements of the DSE103 MKII Series Speed Switch, part of
the DSE range of products.
The manual forms part of the product and should be kept for the entire life of the product. If the product is passed or
supplied to another party, ensure that this document is passed to them for reference purposes.
This is not a controlled document. You will not be automatically informed of updates. Any future updates of this
document will be included on the DSE website at www.deepseaplc.com
The DSE103 MKII Series Speed Switch is designed to monitor the speed of an engine or piece of rotating
machinery by detecting a magnetic pickup pulse or frequency. Should these exceed the configured trip points, the
appropriate relay contact will change state.
The electronics are housed in a robust case encapsulated in resin for environmental protection which is designed
for bolt on mounting. Electrical connections are via ¼” spade connectors.
The modules flexibility allows it to be used for many different applications including under speed and over speed
protection or crank disconnect facilities.
The DSE Configuration Suite Lite software allows configuration of selected operational sequences, timers and
latches.
.
CALL US TODAY
1-888-POWER-58
REQUEST A QUOTE
parts@genpowerusa.com
SHOP ONLINE
www.genpowerusa.com
Loading...